-/*
- * EEPROM related constants, enums, and structures.
- */
-
-/*
- * EEPROM access time values:
- *
- * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
- * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
- * CSR_EEPROM_REG_BIT_CMD (0x2).
- * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
- * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
- * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
- */
-#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
-#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
-
-/* EEPROM field values */
-#define ANTENNA_SWITCH_NORMAL 0
-#define ANTENNA_SWITCH_INVERSE 1
-
-/*
- * Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
- *
- * IBSS and/or AP operation is allowed *only* on those channels with
- * (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
- * RADAR detection is not supported by the 4965 driver, but is a
- * requirement for establishing a new network for legal operation on channels
- * requiring RADAR detection or restricting ACTIVE scanning.
- *
- * NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
- * It only indicates that 20 MHz channel use is supported; FAT channel
- * usage is indicated by a separate set of regulatory flags for each
- * FAT channel pair.
- *
- * NOTE: Using a channel inappropriately will result in a uCode error!
- */
-enum {
- EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
- EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
- /* Bit 2 Reserved */
- EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
- EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
- EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
- EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel, not used */
- EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
-};
-
-/* EEPROM field lengths */
-#define EEPROM_BOARD_PBA_NUMBER_LENGTH 11
-
-/* EEPROM field lengths */
-#define EEPROM_BOARD_PBA_NUMBER_LENGTH 11
-#define EEPROM_REGULATORY_SKU_ID_LENGTH 4
-#define EEPROM_REGULATORY_BAND1_CHANNELS_LENGTH 14
-#define EEPROM_REGULATORY_BAND2_CHANNELS_LENGTH 13
-#define EEPROM_REGULATORY_BAND3_CHANNELS_LENGTH 12
-#define EEPROM_REGULATORY_BAND4_CHANNELS_LENGTH 11
-#define EEPROM_REGULATORY_BAND5_CHANNELS_LENGTH 6
-
-#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS_LENGTH 7
-#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS_LENGTH 11
-#define EEPROM_REGULATORY_CHANNELS_LENGTH ( \
- EEPROM_REGULATORY_BAND1_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND2_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND3_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND4_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND5_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND_24_FAT_CHANNELS_LENGTH + \
- EEPROM_REGULATORY_BAND_52_FAT_CHANNELS_LENGTH)
-
-#define EEPROM_REGULATORY_NUMBER_OF_BANDS 5
-
-/* SKU Capabilities */
-#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
-#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
-#define EEPROM_SKU_CAP_OP_MODE_MRC (1 << 7)
-
-/* *regulatory* channel data format in eeprom, one for each channel.
- * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
-struct iwl4965_eeprom_channel {
- u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
- s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
-} __attribute__ ((packed));
-
-/* 4965 has two radio transmitters (and 3 radio receivers) */
-#define EEPROM_TX_POWER_TX_CHAINS (2)
-
-/* 4965 has room for up to 8 sets of txpower calibration data */
-#define EEPROM_TX_POWER_BANDS (8)
-
-/* 4965 factory calibration measures txpower gain settings for
- * each of 3 target output levels */
-#define EEPROM_TX_POWER_MEASUREMENTS (3)
-
-/* 4965 driver does not work with txpower calibration version < 5.
- * Look for this in calib_version member of struct iwl4965_eeprom. */
-#define EEPROM_TX_POWER_VERSION_NEW (5)
-
-
-/*
- * 4965 factory calibration data for one txpower level, on one channel,
- * measured on one of the 2 tx chains (radio transmitter and associated
- * antenna). EEPROM contains:
- *
- * 1) Temperature (degrees Celsius) of device when measurement was made.
- *
- * 2) Gain table index used to achieve the target measurement power.
- * This refers to the "well-known" gain tables (see iwl-4965-hw.h).
- *
- * 3) Actual measured output power, in half-dBm ("34" = 17 dBm).
- *
- * 4) RF power amplifier detector level measurement (not used).
- */
-struct iwl4965_eeprom_calib_measure {
- u8 temperature; /* Device temperature (Celsius) */
- u8 gain_idx; /* Index into gain table */
- u8 actual_pow; /* Measured RF output power, half-dBm */
- s8 pa_det; /* Power amp detector level (not used) */
-} __attribute__ ((packed));
-
-
-/*
- * 4965 measurement set for one channel. EEPROM contains:
- *
- * 1) Channel number measured
- *
- * 2) Measurements for each of 3 power levels for each of 2 radio transmitters
- * (a.k.a. "tx chains") (6 measurements altogether)
- */
-struct iwl4965_eeprom_calib_ch_info {
- u8 ch_num;
- struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS]
- [EEPROM_TX_POWER_MEASUREMENTS];
-} __attribute__ ((packed));
-
-/*
- * 4965 txpower subband info.
- *
- * For each frequency subband, EEPROM contains the following:
- *
- * 1) First and last channels within range of the subband. "0" values
- * indicate that this sample set is not being used.
- *
- * 2) Sample measurement sets for 2 channels close to the range endpoints.
- */
-struct iwl4965_eeprom_calib_subband_info {
- u8 ch_from; /* channel number of lowest channel in subband */
- u8 ch_to; /* channel number of highest channel in subband */
- struct iwl4965_eeprom_calib_ch_info ch1;
- struct iwl4965_eeprom_calib_ch_info ch2;
-} __attribute__ ((packed));
-
-
-/*
- * 4965 txpower calibration info. EEPROM contains:
- *
- * 1) Factory-measured saturation power levels (maximum levels at which
- * tx power amplifier can output a signal without too much distortion).
- * There is one level for 2.4 GHz band and one for 5 GHz band. These
- * values apply to all channels within each of the bands.
- *
- * 2) Factory-measured power supply voltage level. This is assumed to be
- * constant (i.e. same value applies to all channels/bands) while the
- * factory measurements are being made.
- *
- * 3) Up to 8 sets of factory-measured txpower calibration values.
- * These are for different frequency ranges, since txpower gain
- * characteristics of the analog radio circuitry vary with frequency.
- *
- * Not all sets need to be filled with data;
- * struct iwl4965_eeprom_calib_subband_info contains range of channels
- * (0 if unused) for each set of data.
- */
-struct iwl4965_eeprom_calib_info {
- u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
- u8 saturation_power52; /* half-dBm */
- s16 voltage; /* signed */
- struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS];
-} __attribute__ ((packed));
-
-
-/*
- * 4965 EEPROM map
- */
-struct iwl4965_eeprom {
- u8 reserved0[16];
-#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
- u16 device_id; /* abs.ofs: 16 */
- u8 reserved1[2];
-#define EEPROM_PMC (2*0x0A) /* 2 bytes */
- u16 pmc; /* abs.ofs: 20 */
- u8 reserved2[20];
-#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
- u8 mac_address[6]; /* abs.ofs: 42 */
- u8 reserved3[58];
-#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
- u16 board_revision; /* abs.ofs: 106 */
- u8 reserved4[11];
-#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
- u8 board_pba_number[9]; /* abs.ofs: 119 */
- u8 reserved5[8];
-#define EEPROM_VERSION (2*0x44) /* 2 bytes */
- u16 version; /* abs.ofs: 136 */
-#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
- u8 sku_cap; /* abs.ofs: 138 */
-#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
- u8 leds_mode; /* abs.ofs: 139 */
-#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
- u16 oem_mode;
-#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
- u16 wowlan_mode; /* abs.ofs: 142 */
-#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
- u16 leds_time_interval; /* abs.ofs: 144 */
-#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
- u8 leds_off_time; /* abs.ofs: 146 */
-#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
- u8 leds_on_time; /* abs.ofs: 147 */
-#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
- u8 almgor_m_version; /* abs.ofs: 148 */
-#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
- u8 antenna_switch_type; /* abs.ofs: 149 */
- u8 reserved6[8];
-#define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */
- u16 board_revision_4965; /* abs.ofs: 158 */
- u8 reserved7[13];
-#define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */
- u8 board_pba_number_4965[9]; /* abs.ofs: 173 */
- u8 reserved8[10];
-#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
- u8 sku_id[4]; /* abs.ofs: 192 */
-
-/*
- * Per-channel regulatory data.
- *
- * Each channel that *might* be supported by 3945 or 4965 has a fixed location
- * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
- * txpower (MSB).
- *
- * Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
- * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
- *
- * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
- */
-#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
- u16 band_1_count; /* abs.ofs: 196 */
-#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
- struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
-
-/*
- * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
- * 5.0 GHz channels 7, 8, 11, 12, 16
- * (4915-5080MHz) (none of these is ever supported)
- */
-#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
- u16 band_2_count; /* abs.ofs: 226 */
-#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
- struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
-
-/*
- * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
- * (5170-5320MHz)
- */
-#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
- u16 band_3_count; /* abs.ofs: 254 */
-#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
- struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */