-source "arch/sh/mm/Kconfig"
-
-config CF_ENABLER
- bool "Compact Flash Enabler support"
- depends on SH_SOLUTION_ENGINE || SH_UNKNOWN || SH_SH03
- ---help---
- Compact Flash is a small, removable mass storage device introduced
- in 1994 originally as a PCMCIA device. If you say `Y' here, you
- compile in support for Compact Flash devices directly connected to
- a SuperH processor. A Compact Flash FAQ is available at
- <http://www.compactflash.org/faqs/faq.htm>.
-
- If your board has "Directly Connected" CompactFlash at area 5 or 6,
- you may want to enable this option. Then, you can use CF as
- primary IDE drive (only tested for SanDisk).
-
- If in doubt, select 'N'.
-
-choice
- prompt "Compact Flash Connection Area"
- depends on CF_ENABLER
- default CF_AREA6
-
-config CF_AREA5
- bool "Area5"
- help
- If your board has "Directly Connected" CompactFlash, You should
- select the area where your CF is connected to.
-
- - "Area5" if CompactFlash is connected to Area 5 (0x14000000)
- - "Area6" if it is connected to Area 6 (0x18000000)
-
- "Area6" will work for most boards.
-
-config CF_AREA6
- bool "Area6"
-
-endchoice
-
-config CF_BASE_ADDR
- hex
- depends on CF_ENABLER
- default "0xb8000000" if CF_AREA6
- default "0xb4000000" if CF_AREA5
-
-menu "Processor features"
-
-choice
- prompt "Endianess selection"
- default CPU_LITTLE_ENDIAN
- help
- Some SuperH machines can be configured for either little or big
- endian byte order. These modes require different kernels.
-
-config CPU_LITTLE_ENDIAN
- bool "Little Endian"
-
-config CPU_BIG_ENDIAN
- bool "Big Endian"
-
-endchoice
-
-config SH_FPU
- bool "FPU support"
- depends on !CPU_SH3
- default y
- help
- Selecting this option will enable support for SH processors that
- have FPU units (ie, SH77xx).
-
- This option must be set in order to enable the FPU.
-
-config SH_FPU_EMU
- bool "FPU emulation support"
- depends on !SH_FPU && EXPERIMENTAL
- default n
- help
- Selecting this option will enable support for software FPU emulation.
- Most SH-3 users will want to say Y here, whereas most SH-4 users will
- want to say N.
-
-config SH_DSP
- bool "DSP support"
- default y if SH4AL_DSP || !CPU_SH4
- default n
- help
- Selecting this option will enable support for SH processors that
- have DSP units (ie, SH2-DSP, SH3-DSP, and SH4AL-DSP).
-
- This option must be set in order to enable the DSP.
-
-config SH_ADC
- bool "ADC support"
- depends on CPU_SH3
- default y
- help
- Selecting this option will allow the Linux kernel to use SH3 on-chip
- ADC module.
-
- If unsure, say N.
-
-config SH_STORE_QUEUES
- bool "Support for Store Queues"
- depends on CPU_SH4
- help
- Selecting this option will enable an in-kernel API for manipulating
- the store queues integrated in the SH-4 processors.
-
-config SPECULATIVE_EXECUTION
- bool "Speculative subroutine return"
- depends on CPU_SUBTYPE_SH7780 && EXPERIMENTAL
- help
- This enables support for a speculative instruction fetch for
- subroutine return. There are various pitfalls associated with
- this, as outlined in the SH7780 hardware manual.
-
- If unsure, say N.
-
-config CPU_HAS_INTEVT
- bool
-
-config CPU_HAS_PINT_IRQ
- bool
-
-config CPU_HAS_MASKREG_IRQ
- bool
-
-config CPU_HAS_INTC2_IRQ
- bool
-
-config CPU_HAS_IPR_IRQ
- bool
-
-config CPU_HAS_SR_RB
- bool "CPU has SR.RB"
- depends on CPU_SH3 || CPU_SH4
- default y
- help
- This will enable the use of SR.RB register bank usage. Processors
- that are lacking this bit must have another method in place for
- accomplishing what is taken care of by the banked registers.
-
- See <file:Documentation/sh/register-banks.txt> for further
- information on SR.RB and register banking in the kernel in general.
-
-config CPU_HAS_PTEA
- bool
-
-endmenu
-