+ layout
+ The "layout" for the array for the particular level. This is
+ simply a number that is interpretted differently by different
+ levels. It can be written while assembling an array.
+
+ reshape_position
+ This is either "none" or a sector number within the devices of
+ the array where "reshape" is up to. If this is set, the three
+ attributes mentioned above (raid_disks, chunk_size, layout) can
+ potentially have 2 values, an old and a new value. If these
+ values differ, reading the attribute returns
+ new (old)
+ and writing will effect the 'new' value, leaving the 'old'
+ unchanged.
+
+ component_size
+ For arrays with data redundancy (i.e. not raid0, linear, faulty,
+ multipath), all components must be the same size - or at least
+ there must a size that they all provide space for. This is a key
+ part or the geometry of the array. It is measured in sectors
+ and can be read from here. Writing to this value may resize
+ the array if the personality supports it (raid1, raid5, raid6),
+ and if the component drives are large enough.
+
+ metadata_version
+ This indicates the format that is being used to record metadata
+ about the array. It can be 0.90 (traditional format), 1.0, 1.1,
+ 1.2 (newer format in varying locations) or "none" indicating that
+ the kernel isn't managing metadata at all.
+
+ resync_start
+ The point at which resync should start. If no resync is needed,
+ this will be a very large number. At array creation it will
+ default to 0, though starting the array as 'clean' will
+ set it much larger.
+
+ new_dev
+ This file can be written but not read. The value written should
+ be a block device number as major:minor. e.g. 8:0
+ This will cause that device to be attached to the array, if it is
+ available. It will then appear at md/dev-XXX (depending on the
+ name of the device) and further configuration is then possible.
+
+ safe_mode_delay
+ When an md array has seen no write requests for a certain period
+ of time, it will be marked as 'clean'. When another write
+ request arrives, the array is marked as 'dirty' before the write
+ commences. This is known as 'safe_mode'.
+ The 'certain period' is controlled by this file which stores the
+ period as a number of seconds. The default is 200msec (0.200).
+ Writing a value of 0 disables safemode.
+
+ array_state
+ This file contains a single word which describes the current
+ state of the array. In many cases, the state can be set by
+ writing the word for the desired state, however some states
+ cannot be explicitly set, and some transitions are not allowed.
+
+ clear
+ No devices, no size, no level
+ Writing is equivalent to STOP_ARRAY ioctl
+ inactive
+ May have some settings, but array is not active
+ all IO results in error
+ When written, doesn't tear down array, but just stops it
+ suspended (not supported yet)
+ All IO requests will block. The array can be reconfigured.
+ Writing this, if accepted, will block until array is quiessent
+ readonly
+ no resync can happen. no superblocks get written.
+ write requests fail
+ read-auto
+ like readonly, but behaves like 'clean' on a write request.
+
+ clean - no pending writes, but otherwise active.
+ When written to inactive array, starts without resync
+ If a write request arrives then
+ if metadata is known, mark 'dirty' and switch to 'active'.
+ if not known, block and switch to write-pending
+ If written to an active array that has pending writes, then fails.
+ active
+ fully active: IO and resync can be happening.
+ When written to inactive array, starts with resync
+
+ write-pending
+ clean, but writes are blocked waiting for 'active' to be written.
+
+ active-idle
+ like active, but no writes have been seen for a while (safe_mode_delay).
+
+