[linux-2.6] / include / net / mac80211.h

/*
 * mac80211 <-> driver interface
 *
 * Copyright 2002-2005, Devicescape Software, Inc.
 * Copyright 2006-2007  Jiri Benc <jbenc@suse.cz>
 * Copyright 2007       Johannes Berg <johannes@sipsolutions.net>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef MAC80211_H
#define MAC80211_H

#include <linux/kernel.h>
#include <linux/if_ether.h>
#include <linux/skbuff.h>
#include <linux/wireless.h>
#include <linux/device.h>
#include <linux/ieee80211.h>
#include <net/wireless.h>
#include <net/cfg80211.h>

/* Note! Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
 * called in hardware interrupt context. The low-level driver must not call any
 * other functions in hardware interrupt context. If there is a need for such
 * call, the low-level driver should first ACK the interrupt and perform the
 * IEEE 802.11 code call after this, e.g., from a scheduled tasklet (in
 * software interrupt context).
 */

/*
 * Frame format used when passing frame between low-level hardware drivers
 * and IEEE 802.11 driver the same as used in the wireless media, i.e.,
 * buffers start with IEEE 802.11 header and include the same octets that
 * are sent over air.
 *
 * If hardware uses IEEE 802.3 headers (and perform 802.3 <-> 802.11
 * conversion in firmware), upper layer 802.11 code needs to be changed to
 * support this.
 *
 * If the receive frame format is not the same as the real frame sent
 * on the wireless media (e.g., due to padding etc.), upper layer 802.11 code
 * could be updated to provide support for such format assuming this would
 * optimize the performance, e.g., by removing need to re-allocation and
 * copying of the data.
 */

#define IEEE80211_CHAN_W_SCAN 0x00000001
#define IEEE80211_CHAN_W_ACTIVE_SCAN 0x00000002
#define IEEE80211_CHAN_W_IBSS 0x00000004

/* Channel information structure. Low-level driver is expected to fill in chan,
 * freq, and val fields. Other fields will be filled in by 80211.o based on
 * hostapd information and low-level driver does not need to use them. The
 * limits for each channel will be provided in 'struct ieee80211_conf' when
 * configuring the low-level driver with hw->config callback. If a device has
 * a default regulatory domain, IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED
 * can be set to let the driver configure all fields */
struct ieee80211_channel {
        short chan; /* channel number (IEEE 802.11) */
        short freq; /* frequency in MHz */
        int val; /* hw specific value for the channel */
        int flag; /* flag for hostapd use (IEEE80211_CHAN_*) */
        unsigned char power_level;
        unsigned char antenna_max;
};

#define IEEE80211_RATE_ERP 0x00000001
#define IEEE80211_RATE_BASIC 0x00000002
#define IEEE80211_RATE_PREAMBLE2 0x00000004
#define IEEE80211_RATE_SUPPORTED 0x00000010
#define IEEE80211_RATE_OFDM 0x00000020
#define IEEE80211_RATE_CCK 0x00000040
#define IEEE80211_RATE_TURBO 0x00000080
#define IEEE80211_RATE_MANDATORY 0x00000100

#define IEEE80211_RATE_CCK_2 (IEEE80211_RATE_CCK | IEEE80211_RATE_PREAMBLE2)
#define IEEE80211_RATE_MODULATION(f) \
        (f & (IEEE80211_RATE_CCK | IEEE80211_RATE_OFDM))

/* Low-level driver should set PREAMBLE2, OFDM, CCK, and TURBO flags.
 * BASIC, SUPPORTED, ERP, and MANDATORY flags are set in 80211.o based on the
 * configuration. */
struct ieee80211_rate {
        int rate; /* rate in 100 kbps */
        int val; /* hw specific value for the rate */
        int flags; /* IEEE80211_RATE_ flags */
        int val2; /* hw specific value for the rate when using short preamble
                   * (only when IEEE80211_RATE_PREAMBLE2 flag is set, i.e., for
                   * 2, 5.5, and 11 Mbps) */
        signed char min_rssi_ack;
        unsigned char min_rssi_ack_delta;

        /* following fields are set by 80211.o and need not be filled by the
         * low-level driver */
        int rate_inv; /* inverse of the rate (LCM(all rates) / rate) for
                       * optimizing channel utilization estimates */
};

/* 802.11g is backwards-compatible with 802.11b, so a wlan card can
 * actually be both in 11b and 11g modes at the same time. */
enum {
        MODE_IEEE80211A, /* IEEE 802.11a */
        MODE_IEEE80211B, /* IEEE 802.11b only */
        MODE_ATHEROS_TURBO, /* Atheros Turbo mode (2x.11a at 5 GHz) */
        MODE_IEEE80211G, /* IEEE 802.11g (and 802.11b compatibility) */
        MODE_ATHEROS_TURBOG, /* Atheros Turbo mode (2x.11g at 2.4 GHz) */

        /* keep last */
        NUM_IEEE80211_MODES
};

struct ieee80211_hw_mode {
        int mode; /* MODE_IEEE80211... */
        int num_channels; /* Number of channels (below) */
        struct ieee80211_channel *channels; /* Array of supported channels */
        int num_rates; /* Number of rates (below) */
        struct ieee80211_rate *rates; /* Array of supported rates */

        struct list_head list; /* Internal, don't touch */
};

struct ieee80211_tx_queue_params {
        int aifs; /* 0 .. 255; -1 = use default */
        int cw_min; /* 2^n-1: 1, 3, 7, .. , 1023; 0 = use default */
        int cw_max; /* 2^n-1: 1, 3, 7, .. , 1023; 0 = use default */
        int burst_time; /* maximum burst time in 0.1 ms (i.e., 10 = 1 ms);
                         * 0 = disabled */
};

struct ieee80211_tx_queue_stats_data {
        unsigned int len; /* num packets in queue */
        unsigned int limit; /* queue len (soft) limit */
        unsigned int count; /* total num frames sent */
};

enum {
        IEEE80211_TX_QUEUE_DATA0,
        IEEE80211_TX_QUEUE_DATA1,
        IEEE80211_TX_QUEUE_DATA2,
        IEEE80211_TX_QUEUE_DATA3,
        IEEE80211_TX_QUEUE_DATA4,
        IEEE80211_TX_QUEUE_SVP,

        NUM_TX_DATA_QUEUES,

/* due to stupidity in the sub-ioctl userspace interface, the items in
 * this struct need to have fixed values. As soon as it is removed, we can
 * fix these entries. */
        IEEE80211_TX_QUEUE_AFTER_BEACON = 6,
        IEEE80211_TX_QUEUE_BEACON = 7
};

struct ieee80211_tx_queue_stats {
        struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES];
};

struct ieee80211_low_level_stats {
        unsigned int dot11ACKFailureCount;
        unsigned int dot11RTSFailureCount;
        unsigned int dot11FCSErrorCount;
        unsigned int dot11RTSSuccessCount;
};

/* Transmit control fields. This data structure is passed to low-level driver
 * with each TX frame. The low-level driver is responsible for configuring
 * the hardware to use given values (depending on what is supported). */
#define HW_KEY_IDX_INVALID -1

struct ieee80211_tx_control {
        int tx_rate; /* Transmit rate, given as the hw specific value for the
                      * rate (from struct ieee80211_rate) */
        int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw
                           * specific value for the rate (from
                           * struct ieee80211_rate) */

#define IEEE80211_TXCTL_REQ_TX_STATUS   (1<<0)/* request TX status callback for
                                                * this frame */
#define IEEE80211_TXCTL_DO_NOT_ENCRYPT  (1<<1) /* send this frame without
                                                * encryption; e.g., for EAPOL
                                                * frames */
#define IEEE80211_TXCTL_USE_RTS_CTS     (1<<2) /* use RTS-CTS before sending
                                                * frame */
#define IEEE80211_TXCTL_USE_CTS_PROTECT (1<<3) /* use CTS protection for the
                                                * frame (e.g., for combined
                                                * 802.11g / 802.11b networks) */
#define IEEE80211_TXCTL_NO_ACK          (1<<4) /* tell the low level not to
                                                * wait for an ack */
#define IEEE80211_TXCTL_RATE_CTRL_PROBE (1<<5)
#define IEEE80211_TXCTL_CLEAR_DST_MASK  (1<<6)
#define IEEE80211_TXCTL_REQUEUE         (1<<7)
#define IEEE80211_TXCTL_FIRST_FRAGMENT  (1<<8) /* this is a first fragment of
                                                * the frame */
#define IEEE80211_TXCTL_TKIP_NEW_PHASE1_KEY (1<<9)
#define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send
                                                  * using the through
                                                  * set_retry_limit configured
                                                  * long retry value */
        u32 flags;                             /* tx control flags defined
                                                * above */
        u8 retry_limit;         /* 1 = only first attempt, 2 = one retry, ..
                                 * This could be used when set_retry_limit
                                 * is not implemented by the driver */
        u8 power_level;         /* per-packet transmit power level, in dBm */
        u8 antenna_sel_tx;      /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
        s8 key_idx;             /* HW_KEY_IDX_INVALID = do not encrypt,
                                 * other values: keyidx from hw->set_key() */
        u8 icv_len;             /* length of the ICV/MIC field in octets */
        u8 iv_len;              /* length of the IV field in octets */
        u8 tkip_key[16];        /* generated phase2/phase1 key for hw TKIP */
        u8 queue;               /* hardware queue to use for this frame;
                                 * 0 = highest, hw->queues-1 = lowest */
        u8 sw_retry_attempt;    /* number of times hw has tried to
                                 * transmit frame (not incl. hw retries) */

        struct ieee80211_rate *rate;            /* internal 80211.o rate */
        struct ieee80211_rate *rts_rate;        /* internal 80211.o rate
                                                 * for RTS/CTS */
        int alt_retry_rate; /* retry rate for the last retries, given as the
                             * hw specific value for the rate (from
                             * struct ieee80211_rate). To be used to limit
                             * packet dropping when probing higher rates, if hw
                             * supports multiple retry rates. -1 = not used */
        int type;       /* internal */
        int ifindex;    /* internal */
};

/* Receive status. The low-level driver should provide this information
 * (the subset supported by hardware) to the 802.11 code with each received
 * frame. */
struct ieee80211_rx_status {
        u64 mactime;
        int freq; /* receive frequency in Mhz */
        int channel;
        int phymode;
        int ssi;
        int signal; /* used as qual in statistics reporting */
        int noise;
        int antenna;
        int rate;
#define RX_FLAG_MMIC_ERROR      (1<<0)
#define RX_FLAG_DECRYPTED       (1<<1)
#define RX_FLAG_RADIOTAP        (1<<2)
        int flag;
};

/* Transmit status. The low-level driver should provide this information
 * (the subset supported by hardware) to the 802.11 code for each transmit
 * frame. */
struct ieee80211_tx_status {
        /* copied ieee80211_tx_control structure */
        struct ieee80211_tx_control control;

#define IEEE80211_TX_STATUS_TX_FILTERED (1<<0)
#define IEEE80211_TX_STATUS_ACK         (1<<1) /* whether the TX frame was ACKed */
        u32 flags;              /* tx staus flags defined above */

        int ack_signal; /* measured signal strength of the ACK frame */
        int excessive_retries;
        int retry_count;

        int queue_length;      /* information about TX queue */
        int queue_number;
};


/**
 * struct ieee80211_conf - configuration of the device
 *
 * This struct indicates how the driver shall configure the hardware.
 *
 * @radio_enabled: when zero, driver is required to switch off the radio.
 */
struct ieee80211_conf {
        int channel;                    /* IEEE 802.11 channel number */
        int freq;                       /* MHz */
        int channel_val;                /* hw specific value for the channel */

        int phymode;                    /* MODE_IEEE80211A, .. */
        struct ieee80211_channel *chan;
        struct ieee80211_hw_mode *mode;
        unsigned int regulatory_domain;
        int radio_enabled;

        int beacon_int;

#define IEEE80211_CONF_SHORT_SLOT_TIME  (1<<0) /* use IEEE 802.11g Short Slot
                                                * Time */
#define IEEE80211_CONF_SSID_HIDDEN      (1<<1) /* do not broadcast the ssid */
#define IEEE80211_CONF_RADIOTAP         (1<<2) /* use radiotap if supported
                                                  check this bit at RX time */
        u32 flags;                      /* configuration flags defined above */

        u8 power_level;                 /* transmit power limit for current
                                         * regulatory domain; in dBm */
        u8 antenna_max;                 /* maximum antenna gain */

        /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
        u8 antenna_sel_tx;
        u8 antenna_sel_rx;
};

/**
 * enum ieee80211_if_types - types of 802.11 network interfaces
 *
 * @IEEE80211_IF_TYPE_AP: interface in AP mode.
 * @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap
 *      daemon. Drivers should never see this type.
 * @IEEE80211_IF_TYPE_STA: interface in STA (client) mode.
 * @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode.
 * @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode.
 * @IEEE80211_IF_TYPE_WDS: interface in WDS mode.
 * @IEEE80211_IF_TYPE_VLAN: not used.
 */
enum ieee80211_if_types {
        IEEE80211_IF_TYPE_AP = 0x00000000,
        IEEE80211_IF_TYPE_MGMT = 0x00000001,
        IEEE80211_IF_TYPE_STA = 0x00000002,
        IEEE80211_IF_TYPE_IBSS = 0x00000003,
        IEEE80211_IF_TYPE_MNTR = 0x00000004,
        IEEE80211_IF_TYPE_WDS = 0x5A580211,
        IEEE80211_IF_TYPE_VLAN = 0x00080211,
};

/**
 * struct ieee80211_if_init_conf - initial configuration of an interface
 *
 * @if_id: internal interface ID. This number has no particular meaning to
 *      drivers and the only allowed usage is to pass it to
 *      ieee80211_beacon_get() and ieee80211_get_buffered_bc() functions.
 *      This field is not valid for monitor interfaces
 *      (interfaces of %IEEE80211_IF_TYPE_MNTR type).
 * @type: one of &enum ieee80211_if_types constants. Determines the type of
 *      added/removed interface.
 * @mac_addr: pointer to MAC address of the interface. This pointer is valid
 *      until the interface is removed (i.e. it cannot be used after
 *      remove_interface() callback was called for this interface).
 *      This pointer will be %NULL for monitor interfaces, be careful.
 *
 * This structure is used in add_interface() and remove_interface()
 * callbacks of &struct ieee80211_hw.
 *
 * When you allow multiple interfaces to be added to your PHY, take care
 * that the hardware can actually handle multiple MAC addresses. However,
 * also take care that when there's no interface left with mac_addr != %NULL
 * you remove the MAC address from the device to avoid acknowledging packets
 * in pure monitor mode.
 */
struct ieee80211_if_init_conf {
        int if_id;
        int type;
        void *mac_addr;
};

/**
 * struct ieee80211_if_conf - configuration of an interface
 *
 * @type: type of the interface. This is always the same as was specified in
 *      &struct ieee80211_if_init_conf. The type of an interface never changes
 *      during the life of the interface; this field is present only for
 *      convenience.
 * @bssid: BSSID of the network we are associated to/creating.
 * @ssid: used (together with @ssid_len) by drivers for hardware that
 *      generate beacons independently. The pointer is valid only during the
 *      config_interface() call, so copy the value somewhere if you need
 *      it.
 * @ssid_len: length of the @ssid field.
 * @generic_elem: used (together with @generic_elem_len) by drivers for
 *      hardware that generate beacons independently. The pointer is valid
 *      only during the config_interface() call, so copy the value somewhere
 *      if you need it.
 * @generic_elem_len: length of the generic element.
 * @beacon: beacon template. Valid only if @host_gen_beacon_template in
 *      &struct ieee80211_hw is set. The driver is responsible of freeing
 *      the sk_buff.
 * @beacon_control: tx_control for the beacon template, this field is only
 *      valid when the @beacon field was set.
 *
 * This structure is passed to the config_interface() callback of
 * &struct ieee80211_hw.
 */
struct ieee80211_if_conf {
        int type;
        u8 *bssid;
        u8 *ssid;
        size_t ssid_len;
        u8 *generic_elem;
        size_t generic_elem_len;
        struct sk_buff *beacon;
        struct ieee80211_tx_control *beacon_control;
};

typedef enum {
        ALG_NONE,
        ALG_WEP,
        ALG_TKIP,
        ALG_CCMP,
} ieee80211_key_alg;

struct ieee80211_key_conf {
        /* shall be changed by the driver to anything but HW_KEY_IDX_INVALID */
        int hw_key_idx;

        ieee80211_key_alg alg;

        int keylen;

#define IEEE80211_KEY_FORCE_SW_ENCRYPT (1<<0) /* to be cleared by low-level
                                                 driver */
        u32 flags; /* key configuration flags defined above */

        s8 keyidx;                      /* WEP key index */
        u8 key[0];
};

#define IEEE80211_SEQ_COUNTER_RX        0
#define IEEE80211_SEQ_COUNTER_TX        1

typedef enum {
        SET_KEY, DISABLE_KEY, REMOVE_ALL_KEYS,
} set_key_cmd;

/* This is driver-visible part of the per-hw state the stack keeps. */
struct ieee80211_hw {
        /* points to the cfg80211 wiphy for this piece. Note
         * that you must fill in the perm_addr and dev fields
         * of this structure, use the macros provided below. */
        struct wiphy *wiphy;

        /* assigned by mac80211, don't write */
        struct ieee80211_conf conf;

        /* Single thread workqueue available for driver use
         * Allocated by mac80211 on registration */
        struct workqueue_struct *workqueue;

        /* Pointer to the private area that was
         * allocated with this struct for you. */
        void *priv;

        /* The rest is information about your hardware */

        /* TODO: frame_type 802.11/802.3, sw_encryption requirements */

/* hole at 0 */

        /*
         * The device only needs to be supplied with a beacon template.
         * If you need the host to generate each beacon then don't use
         * this flag and use ieee80211_beacon_get().
         */
#define IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE (1<<1)

        /*
         * Some devices handle decryption internally and do not
         * indicate whether the frame was encrypted (unencrypted frames
         * will be dropped by the hardware, unless specifically allowed
         * through.)
         * It is permissible to not handle all encrypted frames and fall
         * back to software encryption; however, if this flag is set
         * unencrypted frames must be dropped unless the driver is told
         * otherwise via the set_ieee8021x() callback.
         */
#define IEEE80211_HW_DEVICE_HIDES_WEP (1<<2)

        /* Whether RX frames passed to ieee80211_rx() include FCS in the end */
#define IEEE80211_HW_RX_INCLUDES_FCS (1<<3)

        /* Some wireless LAN chipsets buffer broadcast/multicast frames for
         * power saving stations in the hardware/firmware and others rely on
         * the host system for such buffering. This option is used to
         * configure the IEEE 802.11 upper layer to buffer broadcast/multicast
         * frames when there are power saving stations so that low-level driver
         * can fetch them with ieee80211_get_buffered_bc(). */
#define IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING (1<<4)

        /*
         * This flag is only relevant if hardware encryption is used.
         * If set, it has two meanings:
         *  1) the IV and ICV are present in received frames that have
         *     been decrypted (unless IEEE80211_HW_DEVICE_HIDES_WEP is
         *     also set)
         *  2) on transmission, the IV should be generated in software.
         *
         * Please let us know if you *don't* use this flag, the stack would
         * really like to be able to get the IV to keep key statistics
         * accurate.
         */
#define IEEE80211_HW_WEP_INCLUDE_IV (1<<5)

/* hole at 6 */

        /* Force software encryption for TKIP packets if WMM is enabled. */
#define IEEE80211_HW_NO_TKIP_WMM_HWACCEL (1<<7)

        /*
         * Some devices handle Michael MIC internally and do not include MIC in
         * the received packets passed up. This flag must be set for such
         * devices. The 'encryption' frame control bit is expected to be still
         * set in the IEEE 802.11 header with this option unlike with the
         * IEEE80211_HW_DEVICE_HIDES_WEP flag.
         */
#define IEEE80211_HW_DEVICE_STRIPS_MIC (1<<8)

        /* Device is capable of performing full monitor mode even during
         * normal operation. */
#define IEEE80211_HW_MONITOR_DURING_OPER (1<<9)

        /* Device does not need BSSID filter set to broadcast in order to
         * receive all probe responses while scanning */
#define IEEE80211_HW_NO_PROBE_FILTERING (1<<10)

        /* Channels are already configured to the default regulatory domain
         * specified in the device's EEPROM */
#define IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED (1<<11)

        /* calculate Michael MIC for an MSDU when doing hwcrypto */
#define IEEE80211_HW_TKIP_INCLUDE_MMIC (1<<12)
        /* Do TKIP phase1 key mixing in stack to support cards only do
         * phase2 key mixing when doing hwcrypto */
#define IEEE80211_HW_TKIP_REQ_PHASE1_KEY (1<<13)
        /* Do TKIP phase1 and phase2 key mixing in stack and send the generated
         * per-packet RC4 key with each TX frame when doing hwcrypto */
#define IEEE80211_HW_TKIP_REQ_PHASE2_KEY (1<<14)

        u32 flags;                      /* hardware flags defined above */

        /* Set to the size of a needed device specific skb headroom for TX skbs. */
        unsigned int extra_tx_headroom;

        /* This is the time in us to change channels
         */
        int channel_change_time;
        /* Maximum values for various statistics.
         * Leave at 0 to indicate no support. Use negative numbers for dBm. */
        s8 max_rssi;
        s8 max_signal;
        s8 max_noise;

        /* Number of available hardware TX queues for data packets.
         * WMM requires at least four queues. */
        int queues;
};

static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
{
        set_wiphy_dev(hw->wiphy, dev);
}

static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
{
        memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}

/* Configuration block used by the low-level driver to tell the 802.11 code
 * about supported hardware features and to pass function pointers to callback
 * functions. */
struct ieee80211_ops {
        /* Handler that 802.11 module calls for each transmitted frame.
         * skb contains the buffer starting from the IEEE 802.11 header.
         * The low-level driver should send the frame out based on
         * configuration in the TX control data.
         * Must be atomic. */
        int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
                  struct ieee80211_tx_control *control);

        /* Handler that is called when any netdevice attached to the hardware
         * device is set UP for the first time. This can be used, e.g., to
         * enable interrupts and beacon sending. */
        int (*open)(struct ieee80211_hw *hw);

        /* Handler that is called when the last netdevice attached to the
         * hardware device is set DOWN. This can be used, e.g., to disable
         * interrupts and beacon sending. */
        int (*stop)(struct ieee80211_hw *hw);

        /* Handler for asking a driver if a new interface can be added (or,
         * more exactly, set UP). If the handler returns zero, the interface
         * is added. Driver should perform any initialization it needs prior
         * to returning zero. By returning non-zero addition of the interface
         * is inhibited. Unless monitor_during_oper is set, it is guaranteed
         * that monitor interfaces and normal interfaces are mutually
         * exclusive. If assigned, the open() handler is called after
         * add_interface() if this is the first device added. The
         * add_interface() callback has to be assigned because it is the only
         * way to obtain the requested MAC address for any interface.
         */
        int (*add_interface)(struct ieee80211_hw *hw,
                             struct ieee80211_if_init_conf *conf);

        /* Notify a driver that an interface is going down. The stop() handler
         * is called prior to this if this is a last interface. */
        void (*remove_interface)(struct ieee80211_hw *hw,
                                 struct ieee80211_if_init_conf *conf);

        /* Handler for configuration requests. IEEE 802.11 code calls this
         * function to change hardware configuration, e.g., channel. */
        int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);

        /* Handler for configuration requests related to interfaces (e.g.
         * BSSID). */
        int (*config_interface)(struct ieee80211_hw *hw,
                                int if_id, struct ieee80211_if_conf *conf);

        /* ieee80211 drivers do not have access to the &struct net_device
         * that is (are) connected with their device. Hence (and because
         * we need to combine the multicast lists and flags for multiple
         * virtual interfaces), they cannot assign set_multicast_list.
         * The parameters here replace dev->flags and dev->mc_count,
         * dev->mc_list is replaced by calling ieee80211_get_mc_list_item.
         * Must be atomic. */
        void (*set_multicast_list)(struct ieee80211_hw *hw,
                                   unsigned short flags, int mc_count);

        /* Set TIM bit handler. If the hardware/firmware takes care of beacon
         * generation, IEEE 802.11 code uses this function to tell the
         * low-level to set (or clear if set==0) TIM bit for the given aid. If
         * host system is used to generate beacons, this handler is not used
         * and low-level driver should set it to NULL.
         * Must be atomic. */
        int (*set_tim)(struct ieee80211_hw *hw, int aid, int set);

        /*
         * Set encryption key.
         *
         * This is called to enable hardware acceleration of encryption and
         * decryption. The address will be the broadcast address for default
         * keys and the other station's hardware address for individual keys.
         * When transmitting, the TX control data will use the hw_key_idx
         * selected by the low-level driver.
         */
        int (*set_key)(struct ieee80211_hw *hw, set_key_cmd cmd,
                       u8 *address, struct ieee80211_key_conf *key);

        /*
         * Set TX key index for default/broadcast keys. This is needed in cases
         * where wlan card is doing full WEP/TKIP encapsulation (wep_include_iv
         * is not set), in other cases, this function pointer can be set to
         * NULL since the IEEE 802.11 module takes care of selecting the key
         * index for each TX frame.
         */
        int (*set_key_idx)(struct ieee80211_hw *hw, int idx);

        /* Enable/disable IEEE 802.1X. This item requests wlan card to pass
         * unencrypted EAPOL-Key frames even when encryption is configured.
         * If the wlan card does not require such a configuration, this
         * function pointer can be set to NULL. */
        int (*set_ieee8021x)(struct ieee80211_hw *hw, int use_ieee8021x);

        /* Set port authorization state (IEEE 802.1X PAE) to be authorized
         * (authorized=1) or unauthorized (authorized=0). This function can be
         * used if the wlan hardware or low-level driver implements PAE.
         * 80211.o module will anyway filter frames based on authorization
         * state, so this function pointer can be NULL if low-level driver does
         * not require event notification about port state changes.
         * Currently unused. */
        int (*set_port_auth)(struct ieee80211_hw *hw, u8 *addr,
                             int authorized);

        /* Ask the hardware to service the scan request, no need to start
         * the scan state machine in stack. */
        int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);

        /* return low-level statistics */
        int (*get_stats)(struct ieee80211_hw *hw,
                         struct ieee80211_low_level_stats *stats);

        /* For devices that generate their own beacons and probe response
         * or association responses this updates the state of privacy_invoked
         * returns 0 for success or an error number */
        int (*set_privacy_invoked)(struct ieee80211_hw *hw,
                                   int privacy_invoked);

        /* For devices that have internal sequence counters, allow 802.11
         * code to access the current value of a counter */
        int (*get_sequence_counter)(struct ieee80211_hw *hw,
                                    u8* addr, u8 keyidx, u8 txrx,
                                    u32* iv32, u16* iv16);

        /* Configuration of RTS threshold (if device needs it) */
        int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);

        /* Configuration of fragmentation threshold.
         * Assign this if the device does fragmentation by itself,
         * if this method is assigned then the stack will not do
         * fragmentation. */
        int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);

        /* Configuration of retry limits (if device needs it) */
        int (*set_retry_limit)(struct ieee80211_hw *hw,
                               u32 short_retry, u32 long_retr);

        /* Number of STAs in STA table notification (NULL = disabled).
         * Must be atomic. */
        void (*sta_table_notification)(struct ieee80211_hw *hw,
                                       int num_sta);

        /* Handle ERP IE change notifications. Must be atomic. */
        void (*erp_ie_changed)(struct ieee80211_hw *hw, u8 changes,
                               int cts_protection, int preamble);

        /* Flags for the erp_ie_changed changes parameter */
#define IEEE80211_ERP_CHANGE_PROTECTION (1<<0) /* protection flag changed */
#define IEEE80211_ERP_CHANGE_PREAMBLE (1<<1) /* barker preamble mode changed */

        /* Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
         * bursting) for a hardware TX queue.
         * queue = IEEE80211_TX_QUEUE_*.
         * Must be atomic. */
        int (*conf_tx)(struct ieee80211_hw *hw, int queue,
                       const struct ieee80211_tx_queue_params *params);

        /* Get statistics of the current TX queue status. This is used to get
         * number of currently queued packets (queue length), maximum queue
         * size (limit), and total number of packets sent using each TX queue
         * (count).
         * Currently unused. */
        int (*get_tx_stats)(struct ieee80211_hw *hw,
                            struct ieee80211_tx_queue_stats *stats);

        /* Get the current TSF timer value from firmware/hardware. Currently,
         * this is only used for IBSS mode debugging and, as such, is not a
         * required function.
         * Must be atomic. */
        u64 (*get_tsf)(struct ieee80211_hw *hw);

        /* Reset the TSF timer and allow firmware/hardware to synchronize with
         * other STAs in the IBSS. This is only used in IBSS mode. This
         * function is optional if the firmware/hardware takes full care of
         * TSF synchronization. */
        void (*reset_tsf)(struct ieee80211_hw *hw);

        /* Setup beacon data for IBSS beacons. Unlike access point (Master),
         * IBSS uses a fixed beacon frame which is configured using this
         * function. This handler is required only for IBSS mode. */
        int (*beacon_update)(struct ieee80211_hw *hw,
                             struct sk_buff *skb,
                             struct ieee80211_tx_control *control);

        /* Determine whether the last IBSS beacon was sent by us. This is
         * needed only for IBSS mode and the result of this function is used to
         * determine whether to reply to Probe Requests. */
        int (*tx_last_beacon)(struct ieee80211_hw *hw);
};

/* Allocate a new hardware device. This must be called once for each
 * hardware device. The returned pointer must be used to refer to this
 * device when calling other functions. 802.11 code allocates a private data
 * area for the low-level driver. The size of this area is given as
 * priv_data_len.
 */
struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
                                        const struct ieee80211_ops *ops);

/* Register hardware device to the IEEE 802.11 code and kernel. Low-level
 * drivers must call this function before using any other IEEE 802.11
 * function except ieee80211_register_hwmode. */
int ieee80211_register_hw(struct ieee80211_hw *hw);

/* driver can use this and ieee80211_get_rx_led_name to get the
 * name of the registered LEDs after ieee80211_register_hw
 * was called.
 * This is useful to set the default trigger on the LED class
 * device that your driver should export for each LED the device
 * has, that way the default behaviour will be as expected but
 * the user can still change it/turn off the LED etc.
 */
#ifdef CONFIG_MAC80211_LEDS
extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
#endif
static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
        return __ieee80211_get_tx_led_name(hw);
#else
        return NULL;
#endif
}

static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
        return __ieee80211_get_rx_led_name(hw);
#else
        return NULL;
#endif
}

/* Register a new hardware PHYMODE capability to the stack. */
int ieee80211_register_hwmode(struct ieee80211_hw *hw,
                              struct ieee80211_hw_mode *mode);

/* Unregister a hardware device. This function instructs 802.11 code to free
 * allocated resources and unregister netdevices from the kernel. */
void ieee80211_unregister_hw(struct ieee80211_hw *hw);

/* Free everything that was allocated including private data of a driver. */
void ieee80211_free_hw(struct ieee80211_hw *hw);

/* Receive frame callback function. The low-level driver uses this function to
 * send received frames to the IEEE 802.11 code. Receive buffer (skb) must
 * start with IEEE 802.11 header. */
void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb,
                    struct ieee80211_rx_status *status);
void ieee80211_rx_irqsafe(struct ieee80211_hw *hw,
                          struct sk_buff *skb,
                          struct ieee80211_rx_status *status);

/* Transmit status callback function. The low-level driver must call this
 * function to report transmit status for all the TX frames that had
 * req_tx_status set in the transmit control fields. In addition, this should
 * be called at least for all unicast frames to provide information for TX rate
 * control algorithm. In order to maintain all statistics, this function is
 * recommended to be called after each frame, including multicast/broadcast, is
 * sent. */
void ieee80211_tx_status(struct ieee80211_hw *hw,
                         struct sk_buff *skb,
                         struct ieee80211_tx_status *status);
void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
                                 struct sk_buff *skb,
                                 struct ieee80211_tx_status *status);

/**
 * ieee80211_beacon_get - beacon generation function
 * @hw: pointer obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @control: will be filled with information needed to send this beacon.
 *
 * If the beacon frames are generated by the host system (i.e., not in
 * hardware/firmware), the low-level driver uses this function to receive
 * the next beacon frame from the 802.11 code. The low-level is responsible
 * for calling this function before beacon data is needed (e.g., based on
 * hardware interrupt). Returned skb is used only once and low-level driver
 * is responsible of freeing it.
 */
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
                                     int if_id,
                                     struct ieee80211_tx_control *control);

/**
 * ieee80211_rts_get - RTS frame generation function
 * @hw: pointer obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @frame: pointer to the frame that is going to be protected by the RTS.
 * @frame_len: the frame length (in octets).
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 * @rts: The buffer where to store the RTS frame.
 *
 * If the RTS frames are generated by the host system (i.e., not in
 * hardware/firmware), the low-level driver uses this function to receive
 * the next RTS frame from the 802.11 code. The low-level is responsible
 * for calling this function before and RTS frame is needed.
 */
void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
                       const void *frame, size_t frame_len,
                       const struct ieee80211_tx_control *frame_txctl,
                       struct ieee80211_rts *rts);

/**
 * ieee80211_rts_duration - Get the duration field for an RTS frame
 * @hw: pointer obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @frame_len: the length of the frame that is going to be protected by the RTS.
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 *
 * If the RTS is generated in firmware, but the host system must provide
 * the duration field, the low-level driver uses this function to receive
 * the duration field value in little-endian byteorder.
 */
__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, int if_id,
                              size_t frame_len,
                              const struct ieee80211_tx_control *frame_txctl);

/**
 * ieee80211_ctstoself_get - CTS-to-self frame generation function
 * @hw: pointer obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
 * @frame_len: the frame length (in octets).
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 * @cts: The buffer where to store the CTS-to-self frame.
 *
 * If the CTS-to-self frames are generated by the host system (i.e., not in
 * hardware/firmware), the low-level driver uses this function to receive
 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
 * for calling this function before and CTS-to-self frame is needed.
 */
void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
                             const void *frame, size_t frame_len,
                             const struct ieee80211_tx_control *frame_txctl,
                             struct ieee80211_cts *cts);

/**
 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
 * @hw: pointer obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
 * @frame_txctl: &struct ieee80211_tx_control of the frame.
 *
 * If the CTS-to-self is generated in firmware, but the host system must provide
 * the duration field, the low-level driver uses this function to receive
 * the duration field value in little-endian byteorder.
 */
__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, int if_id,
                                    size_t frame_len,
                                    const struct ieee80211_tx_control *frame_txctl);

/**
 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
 * @hw: pointer obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @frame_len: the length of the frame.
 * @rate: the rate (in 100kbps) at which the frame is going to be transmitted.
 *
 * Calculate the duration field of some generic frame, given its
 * length and transmission rate (in 100kbps).
 */
__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, int if_id,
                                        size_t frame_len,
                                        int rate);

/**
 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @if_id: interface ID from &struct ieee80211_if_init_conf.
 * @control: will be filled with information needed to send returned frame.
 *
 * Function for accessing buffered broadcast and multicast frames. If
 * hardware/firmware does not implement buffering of broadcast/multicast
 * frames when power saving is used, 802.11 code buffers them in the host
 * memory. The low-level driver uses this function to fetch next buffered
 * frame. In most cases, this is used when generating beacon frame. This
 * function returns a pointer to the next buffered skb or NULL if no more
 * buffered frames are available.
 *
 * Note: buffered frames are returned only after DTIM beacon frame was
 * generated with ieee80211_beacon_get() and the low-level driver must thus
 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
 * NULL if the previous generated beacon was not DTIM, so the low-level driver
 * does not need to check for DTIM beacons separately and should be able to
 * use common code for all beacons.
 */
struct sk_buff *
ieee80211_get_buffered_bc(struct ieee80211_hw *hw, int if_id,
                          struct ieee80211_tx_control *control);

/* Given an sk_buff with a raw 802.11 header at the data pointer this function
 * returns the 802.11 header length in bytes (not including encryption
 * headers). If the data in the sk_buff is too short to contain a valid 802.11
 * header the function returns 0.
 */
int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);

/* Like ieee80211_get_hdrlen_from_skb() but takes a FC in CPU order. */
int ieee80211_get_hdrlen(u16 fc);

/**
 * ieee80211_wake_queue - wake specific queue
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @queue: queue number (counted from zero).
 *
 * Drivers should use this function instead of netif_wake_queue.
 */
void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);

/**
 * ieee80211_stop_queue - stop specific queue
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @queue: queue number (counted from zero).
 *
 * Drivers should use this function instead of netif_stop_queue.
 */
void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);

/**
 * ieee80211_start_queues - start all queues
 * @hw: pointer to as obtained from ieee80211_alloc_hw().
 *
 * Drivers should use this function instead of netif_start_queue.
 */
void ieee80211_start_queues(struct ieee80211_hw *hw);

/**
 * ieee80211_stop_queues - stop all queues
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 *
 * Drivers should use this function instead of netif_stop_queue.
 */
void ieee80211_stop_queues(struct ieee80211_hw *hw);

/**
 * ieee80211_wake_queues - wake all queues
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 *
 * Drivers should use this function instead of netif_wake_queue.
 */
void ieee80211_wake_queues(struct ieee80211_hw *hw);

/**
 * ieee80211_get_mc_list_item - iteration over items in multicast list
 * @hw: pointer as obtained from ieee80211_alloc_hw().
 * @prev: value returned by previous call to ieee80211_get_mc_list_item() or
 *      NULL to start a new iteration.
 * @ptr: pointer to buffer of void * type for internal usage of
 *      ieee80211_get_mc_list_item().
 *
 * Iterates over items in multicast list of given device. To get the first
 * item, pass NULL in @prev and in *@ptr. In subsequent calls, pass the
 * value returned by previous call in @prev. Don't alter *@ptr during
 * iteration. When there are no more items, NULL is returned.
 */
struct dev_mc_list *
ieee80211_get_mc_list_item(struct ieee80211_hw *hw,
                           struct dev_mc_list *prev,
                           void **ptr);

/* called by driver to notify scan status completed */
void ieee80211_scan_completed(struct ieee80211_hw *hw);

/* return a pointer to the source address (SA) */
static inline u8 *ieee80211_get_SA(struct ieee80211_hdr *hdr)
{
        u8 *raw = (u8 *) hdr;
        u8 tofrom = (*(raw+1)) & 3; /* get the TODS and FROMDS bits */

        switch (tofrom) {
                case 2:
                        return hdr->addr3;
                case 3:
                        return hdr->addr4;
        }
        return hdr->addr2;
}

/* return a pointer to the destination address (DA) */
static inline u8 *ieee80211_get_DA(struct ieee80211_hdr *hdr)
{
        u8 *raw = (u8 *) hdr;
        u8 to_ds = (*(raw+1)) & 1; /* get the TODS bit */

        if (to_ds)
                return hdr->addr3;
        return hdr->addr1;
}

static inline int ieee80211_get_morefrag(struct ieee80211_hdr *hdr)
{
        return (le16_to_cpu(hdr->frame_control) &
                IEEE80211_FCTL_MOREFRAGS) != 0;
}

#define MAC_FMT "%02x:%02x:%02x:%02x:%02x:%02x"
#define MAC_ARG(x) ((u8*)(x))[0], ((u8*)(x))[1], ((u8*)(x))[2], \
                   ((u8*)(x))[3], ((u8*)(x))[4], ((u8*)(x))[5]

#endif /* MAC80211_H */