err.no Git - linux-2.6/blob - drivers/usb/host/ohci-omap.c

   1 /*
   2  * OHCI HCD (Host Controller Driver) for USB.
   3  *
   4  * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
   5  * (C) Copyright 2000-2005 David Brownell
   6  * (C) Copyright 2002 Hewlett-Packard Company
   7  *
   8  * OMAP Bus Glue
   9  *
  10  * Modified for OMAP by Tony Lindgren <tony@atomide.com>
  11  * Based on the 2.4 OMAP OHCI driver originally done by MontaVista Software Inc.
  12  * and on ohci-sa1111.c by Christopher Hoover <ch@hpl.hp.com>
  13  *
  14  * This file is licenced under the GPL.
  15  */
  16
  17 #include <linux/signal.h>       /* IRQF_DISABLED */
  18 #include <linux/jiffies.h>
  19 #include <linux/platform_device.h>
  20 #include <linux/clk.h>
  21
  22 #include <asm/hardware.h>
  23 #include <asm/io.h>
  24 #include <asm/mach-types.h>
  25
  26 #include <asm/arch/mux.h>
  27 #include <asm/arch/irqs.h>
  28 #include <asm/arch/gpio.h>
  29 #include <asm/arch/fpga.h>
  30 #include <asm/arch/usb.h>
  31
  32
  33 /* OMAP-1510 OHCI has its own MMU for DMA */
  34 #define OMAP1510_LB_MEMSIZE     32      /* Should be same as SDRAM size */
  35 #define OMAP1510_LB_CLOCK_DIV   0xfffec10c
  36 #define OMAP1510_LB_MMU_CTL     0xfffec208
  37 #define OMAP1510_LB_MMU_LCK     0xfffec224
  38 #define OMAP1510_LB_MMU_LD_TLB  0xfffec228
  39 #define OMAP1510_LB_MMU_CAM_H   0xfffec22c
  40 #define OMAP1510_LB_MMU_CAM_L   0xfffec230
  41 #define OMAP1510_LB_MMU_RAM_H   0xfffec234
  42 #define OMAP1510_LB_MMU_RAM_L   0xfffec238
  43
  44
  45 #ifndef CONFIG_ARCH_OMAP
  46 #error "This file is OMAP bus glue.  CONFIG_OMAP must be defined."
  47 #endif
  48
  49 #ifdef CONFIG_TPS65010
  50 #include <linux/i2c/tps65010.h>
  51 #else
  52
  53 #define LOW     0
  54 #define HIGH    1
  55
  56 #define GPIO1   1
  57
  58 static inline int tps65010_set_gpio_out_value(unsigned gpio, unsigned value)
  59 {
  60         return 0;
  61 }
  62
  63 #endif
  64
  65 extern int usb_disabled(void);
  66 extern int ocpi_enable(void);
  67
  68 static struct clk *usb_host_ck;
  69 static struct clk *usb_dc_ck;
  70 static int host_enabled;
  71 static int host_initialized;
  72
  73 static void omap_ohci_clock_power(int on)
  74 {
  75         if (on) {
  76                 clk_enable(usb_dc_ck);
  77                 clk_enable(usb_host_ck);
  78                 /* guesstimate for T5 == 1x 32K clock + APLL lock time */
  79                 udelay(100);
  80         } else {
  81                 clk_disable(usb_host_ck);
  82                 clk_disable(usb_dc_ck);
  83         }
  84 }
  85
  86 /*
  87  * Board specific gang-switched transceiver power on/off.
  88  * NOTE:  OSK supplies power from DC, not battery.
  89  */
  90 static int omap_ohci_transceiver_power(int on)
  91 {
  92         if (on) {
  93                 if (machine_is_omap_innovator() && cpu_is_omap1510())
  94                         fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
  95                                 | ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
  96                                INNOVATOR_FPGA_CAM_USB_CONTROL);
  97                 else if (machine_is_omap_osk())
  98                         tps65010_set_gpio_out_value(GPIO1, LOW);
  99         } else {
 100                 if (machine_is_omap_innovator() && cpu_is_omap1510())
 101                         fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
 102                                 & ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
 103                                INNOVATOR_FPGA_CAM_USB_CONTROL);
 104                 else if (machine_is_omap_osk())
 105                         tps65010_set_gpio_out_value(GPIO1, HIGH);
 106         }
 107
 108         return 0;
 109 }
 110
 111 #ifdef CONFIG_ARCH_OMAP15XX
 112 /*
 113  * OMAP-1510 specific Local Bus clock on/off
 114  */
 115 static int omap_1510_local_bus_power(int on)
 116 {
 117         if (on) {
 118                 omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
 119                 udelay(200);
 120         } else {
 121                 omap_writel(0, OMAP1510_LB_MMU_CTL);
 122         }
 123
 124         return 0;
 125 }
 126
 127 /*
 128  * OMAP-1510 specific Local Bus initialization
 129  * NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
 130  *       See also arch/mach-omap/memory.h for __virt_to_dma() and
 131  *       __dma_to_virt() which need to match with the physical
 132  *       Local Bus address below.
 133  */
 134 static int omap_1510_local_bus_init(void)
 135 {
 136         unsigned int tlb;
 137         unsigned long lbaddr, physaddr;
 138
 139         omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
 140                OMAP1510_LB_CLOCK_DIV);
 141
 142         /* Configure the Local Bus MMU table */
 143         for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
 144                 lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
 145                 physaddr = tlb * 0x00100000 + PHYS_OFFSET;
 146                 omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
 147                 omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
 148                        OMAP1510_LB_MMU_CAM_L);
 149                 omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
 150                 omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
 151                 omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
 152                 omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
 153         }
 154
 155         /* Enable the walking table */
 156         omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
 157         udelay(200);
 158
 159         return 0;
 160 }
 161 #else
 162 #define omap_1510_local_bus_power(x)    {}
 163 #define omap_1510_local_bus_init()      {}
 164 #endif
 165
 166 #ifdef  CONFIG_USB_OTG
 167
 168 static void start_hnp(struct ohci_hcd *ohci)
 169 {
 170         const unsigned  port = ohci_to_hcd(ohci)->self.otg_port - 1;
 171         unsigned long   flags;
 172         u32 l;
 173
 174         otg_start_hnp(ohci->transceiver);
 175
 176         local_irq_save(flags);
 177         ohci->transceiver->state = OTG_STATE_A_SUSPEND;
 178         writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]);
 179         l = omap_readl(OTG_CTRL);
 180         l &= ~OTG_A_BUSREQ;
 181         omap_writel(l, OTG_CTRL);
 182         local_irq_restore(flags);
 183 }
 184
 185 #endif
 186
 187 /*-------------------------------------------------------------------------*/
 188
 189 static int ohci_omap_init(struct usb_hcd *hcd)
 190 {
 191         struct ohci_hcd         *ohci = hcd_to_ohci(hcd);
 192         struct omap_usb_config  *config = hcd->self.controller->platform_data;
 193         int                     need_transceiver = (config->otg != 0);
 194         int                     ret;
 195
 196         dev_dbg(hcd->self.controller, "starting USB Controller\n");
 197
 198         if (config->otg) {
 199                 ohci_to_hcd(ohci)->self.otg_port = config->otg;
 200                 /* default/minimum OTG power budget:  8 mA */
 201                 ohci_to_hcd(ohci)->power_budget = 8;
 202         }
 203
 204         /* boards can use OTG transceivers in non-OTG modes */
 205         need_transceiver = need_transceiver
 206                         || machine_is_omap_h2() || machine_is_omap_h3();
 207
 208         if (cpu_is_omap16xx())
 209                 ocpi_enable();
 210
 211 #ifdef  CONFIG_ARCH_OMAP_OTG
 212         if (need_transceiver) {
 213                 ohci->transceiver = otg_get_transceiver();
 214                 if (ohci->transceiver) {
 215                         int     status = otg_set_host(ohci->transceiver,
 216                                                 &ohci_to_hcd(ohci)->self);
 217                         dev_dbg(hcd->self.controller, "init %s transceiver, status %d\n",
 218                                         ohci->transceiver->label, status);
 219                         if (status) {
 220                                 if (ohci->transceiver)
 221                                         put_device(ohci->transceiver->dev);
 222                                 return status;
 223                         }
 224                 } else {
 225                         dev_err(hcd->self.controller, "can't find transceiver\n");
 226                         return -ENODEV;
 227                 }
 228         }
 229 #endif
 230
 231         omap_ohci_clock_power(1);
 232
 233         if (cpu_is_omap1510()) {
 234                 omap_1510_local_bus_power(1);
 235                 omap_1510_local_bus_init();
 236         }
 237
 238         if ((ret = ohci_init(ohci)) < 0)
 239                 return ret;
 240
 241         /* board-specific power switching and overcurrent support */
 242         if (machine_is_omap_osk() || machine_is_omap_innovator()) {
 243                 u32     rh = roothub_a (ohci);
 244
 245                 /* power switching (ganged by default) */
 246                 rh &= ~RH_A_NPS;
 247
 248                 /* TPS2045 switch for internal transceiver (port 1) */
 249                 if (machine_is_omap_osk()) {
 250                         ohci_to_hcd(ohci)->power_budget = 250;
 251
 252                         rh &= ~RH_A_NOCP;
 253
 254                         /* gpio9 for overcurrent detction */
 255                         omap_cfg_reg(W8_1610_GPIO9);
 256                         omap_request_gpio(9);
 257                         omap_set_gpio_direction(9, 1 /* IN */);
 258
 259                         /* for paranoia's sake:  disable USB.PUEN */
 260                         omap_cfg_reg(W4_USB_HIGHZ);
 261                 }
 262                 ohci_writel(ohci, rh, &ohci->regs->roothub.a);
 263                 distrust_firmware = 0;
 264         } else if (machine_is_nokia770()) {
 265                 /* We require a self-powered hub, which should have
 266                  * plenty of power. */
 267                 ohci_to_hcd(ohci)->power_budget = 0;
 268         }
 269
 270         /* FIXME khubd hub requests should manage power switching */
 271         omap_ohci_transceiver_power(1);
 272
 273         /* board init will have already handled HMC and mux setup.
 274          * any external transceiver should already be initialized
 275          * too, so all configured ports use the right signaling now.
 276          */
 277
 278         return 0;
 279 }
 280
 281 static void ohci_omap_stop(struct usb_hcd *hcd)
 282 {
 283         dev_dbg(hcd->self.controller, "stopping USB Controller\n");
 284         omap_ohci_clock_power(0);
 285 }
 286
 287
 288 /*-------------------------------------------------------------------------*/
 289
 290 /**
 291  * usb_hcd_omap_probe - initialize OMAP-based HCDs
 292  * Context: !in_interrupt()
 293  *
 294  * Allocates basic resources for this USB host controller, and
 295  * then invokes the start() method for the HCD associated with it
 296  * through the hotplug entry's driver_data.
 297  */
 298 static int usb_hcd_omap_probe (const struct hc_driver *driver,
 299                           struct platform_device *pdev)
 300 {
 301         int retval, irq;
 302         struct usb_hcd *hcd = 0;
 303         struct ohci_hcd *ohci;
 304
 305         if (pdev->num_resources != 2) {
 306                 printk(KERN_ERR "hcd probe: invalid num_resources: %i\n",
 307                        pdev->num_resources);
 308                 return -ENODEV;
 309         }
 310
 311         if (pdev->resource[0].flags != IORESOURCE_MEM
 312                         || pdev->resource[1].flags != IORESOURCE_IRQ) {
 313                 printk(KERN_ERR "hcd probe: invalid resource type\n");
 314                 return -ENODEV;
 315         }
 316
 317         usb_host_ck = clk_get(0, "usb_hhc_ck");
 318         if (IS_ERR(usb_host_ck))
 319                 return PTR_ERR(usb_host_ck);
 320
 321         if (!cpu_is_omap1510())
 322                 usb_dc_ck = clk_get(0, "usb_dc_ck");
 323         else
 324                 usb_dc_ck = clk_get(0, "lb_ck");
 325
 326         if (IS_ERR(usb_dc_ck)) {
 327                 clk_put(usb_host_ck);
 328                 return PTR_ERR(usb_dc_ck);
 329         }
 330
 331
 332         hcd = usb_create_hcd (driver, &pdev->dev, dev_name(&pdev->dev));
 333         if (!hcd) {
 334                 retval = -ENOMEM;
 335                 goto err0;
 336         }
 337         hcd->rsrc_start = pdev->resource[0].start;
 338         hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
 339
 340         if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
 341                 dev_dbg(&pdev->dev, "request_mem_region failed\n");
 342                 retval = -EBUSY;
 343                 goto err1;
 344         }
 345
 346         hcd->regs = (void __iomem *) (int) IO_ADDRESS(hcd->rsrc_start);
 347
 348         ohci = hcd_to_ohci(hcd);
 349         ohci_hcd_init(ohci);
 350
 351         host_initialized = 0;
 352         host_enabled = 1;
 353
 354         irq = platform_get_irq(pdev, 0);
 355         if (irq < 0) {
 356                 retval = -ENXIO;
 357                 goto err2;
 358         }
 359         retval = usb_add_hcd(hcd, irq, IRQF_DISABLED);
 360         if (retval)
 361                 goto err2;
 362
 363         host_initialized = 1;
 364
 365         if (!host_enabled)
 366                 omap_ohci_clock_power(0);
 367
 368         return 0;
 369 err2:
 370         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 371 err1:
 372         usb_put_hcd(hcd);
 373 err0:
 374         clk_put(usb_dc_ck);
 375         clk_put(usb_host_ck);
 376         return retval;
 377 }
 378
 379
 380 /* may be called with controller, bus, and devices active */
 381
 382 /**
 383  * usb_hcd_omap_remove - shutdown processing for OMAP-based HCDs
 384  * @dev: USB Host Controller being removed
 385  * Context: !in_interrupt()
 386  *
 387  * Reverses the effect of usb_hcd_omap_probe(), first invoking
 388  * the HCD's stop() method.  It is always called from a thread
 389  * context, normally "rmmod", "apmd", or something similar.
 390  */
 391 static inline void
 392 usb_hcd_omap_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 393 {
 394         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 395
 396         usb_remove_hcd(hcd);
 397         if (ohci->transceiver) {
 398                 (void) otg_set_host(ohci->transceiver, 0);
 399                 put_device(ohci->transceiver->dev);
 400         }
 401         if (machine_is_omap_osk())
 402                 omap_free_gpio(9);
 403         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 404         usb_put_hcd(hcd);
 405         clk_put(usb_dc_ck);
 406         clk_put(usb_host_ck);
 407 }
 408
 409 /*-------------------------------------------------------------------------*/
 410
 411 static int
 412 ohci_omap_start (struct usb_hcd *hcd)
 413 {
 414         struct omap_usb_config *config;
 415         struct ohci_hcd *ohci = hcd_to_ohci (hcd);
 416         int             ret;
 417
 418         if (!host_enabled)
 419                 return 0;
 420         config = hcd->self.controller->platform_data;
 421         if (config->otg || config->rwc) {
 422                 ohci->hc_control = OHCI_CTRL_RWC;
 423                 writel(OHCI_CTRL_RWC, &ohci->regs->control);
 424         }
 425
 426         if ((ret = ohci_run (ohci)) < 0) {
 427                 dev_err(hcd->self.controller, "can't start\n");
 428                 ohci_stop (hcd);
 429                 return ret;
 430         }
 431         return 0;
 432 }
 433
 434 /*-------------------------------------------------------------------------*/
 435
 436 static const struct hc_driver ohci_omap_hc_driver = {
 437         .description =          hcd_name,
 438         .product_desc =         "OMAP OHCI",
 439         .hcd_priv_size =        sizeof(struct ohci_hcd),
 440
 441         /*
 442          * generic hardware linkage
 443          */
 444         .irq =                  ohci_irq,
 445         .flags =                HCD_USB11 | HCD_MEMORY,
 446
 447         /*
 448          * basic lifecycle operations
 449          */
 450         .reset =                ohci_omap_init,
 451         .start =                ohci_omap_start,
 452         .stop =                 ohci_omap_stop,
 453         .shutdown =             ohci_shutdown,
 454
 455         /*
 456          * managing i/o requests and associated device resources
 457          */
 458         .urb_enqueue =          ohci_urb_enqueue,
 459         .urb_dequeue =          ohci_urb_dequeue,
 460         .endpoint_disable =     ohci_endpoint_disable,
 461
 462         /*
 463          * scheduling support
 464          */
 465         .get_frame_number =     ohci_get_frame,
 466
 467         /*
 468          * root hub support
 469          */
 470         .hub_status_data =      ohci_hub_status_data,
 471         .hub_control =          ohci_hub_control,
 472         .hub_irq_enable =       ohci_rhsc_enable,
 473 #ifdef  CONFIG_PM
 474         .bus_suspend =          ohci_bus_suspend,
 475         .bus_resume =           ohci_bus_resume,
 476 #endif
 477         .start_port_reset =     ohci_start_port_reset,
 478 };
 479
 480 /*-------------------------------------------------------------------------*/
 481
 482 static int ohci_hcd_omap_drv_probe(struct platform_device *dev)
 483 {
 484         return usb_hcd_omap_probe(&ohci_omap_hc_driver, dev);
 485 }
 486
 487 static int ohci_hcd_omap_drv_remove(struct platform_device *dev)
 488 {
 489         struct usb_hcd          *hcd = platform_get_drvdata(dev);
 490
 491         usb_hcd_omap_remove(hcd, dev);
 492         platform_set_drvdata(dev, NULL);
 493
 494         return 0;
 495 }
 496
 497 /*-------------------------------------------------------------------------*/
 498
 499 #ifdef  CONFIG_PM
 500
 501 static int ohci_omap_suspend(struct platform_device *dev, pm_message_t message)
 502 {
 503         struct ohci_hcd *ohci = hcd_to_ohci(platform_get_drvdata(dev));
 504
 505         if (time_before(jiffies, ohci->next_statechange))
 506                 msleep(5);
 507         ohci->next_statechange = jiffies;
 508
 509         omap_ohci_clock_power(0);
 510         ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
 511         return 0;
 512 }
 513
 514 static int ohci_omap_resume(struct platform_device *dev)
 515 {
 516         struct usb_hcd  *hcd = platform_get_drvdata(dev);
 517         struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 518
 519         if (time_before(jiffies, ohci->next_statechange))
 520                 msleep(5);
 521         ohci->next_statechange = jiffies;
 522
 523         omap_ohci_clock_power(1);
 524         ohci_finish_controller_resume(hcd);
 525         return 0;
 526 }
 527
 528 #endif
 529
 530 /*-------------------------------------------------------------------------*/
 531
 532 /*
 533  * Driver definition to register with the OMAP bus
 534  */
 535 static struct platform_driver ohci_hcd_omap_driver = {
 536         .probe          = ohci_hcd_omap_drv_probe,
 537         .remove         = ohci_hcd_omap_drv_remove,
 538         .shutdown       = usb_hcd_platform_shutdown,
 539 #ifdef  CONFIG_PM
 540         .suspend        = ohci_omap_suspend,
 541         .resume         = ohci_omap_resume,
 542 #endif
 543         .driver         = {
 544                 .owner  = THIS_MODULE,
 545                 .name   = "ohci",
 546         },
 547 };
 548
 549 MODULE_ALIAS("platform:ohci");