2 * sata_mv.c - Marvell SATA support
4 * Copyright 2005: EMC Corporation, all rights reserved.
5 * Copyright 2005 Red Hat, Inc. All rights reserved.
7 * Please ALWAYS copy linux-ide@vger.kernel.org on emails.
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License as published by
11 * the Free Software Foundation; version 2 of the License.
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
24 #include <linux/kernel.h>
25 #include <linux/module.h>
26 #include <linux/pci.h>
27 #include <linux/init.h>
28 #include <linux/blkdev.h>
29 #include <linux/delay.h>
30 #include <linux/interrupt.h>
31 #include <linux/sched.h>
32 #include <linux/dma-mapping.h>
33 #include <linux/device.h>
34 #include <scsi/scsi_host.h>
35 #include <scsi/scsi_cmnd.h>
36 #include <linux/libata.h>
39 #define DRV_NAME "sata_mv"
40 #define DRV_VERSION "0.6"
43 /* BAR's are enumerated in terms of pci_resource_start() terms */
44 MV_PRIMARY_BAR = 0, /* offset 0x10: memory space */
45 MV_IO_BAR = 2, /* offset 0x18: IO space */
46 MV_MISC_BAR = 3, /* offset 0x1c: FLASH, NVRAM, SRAM */
48 MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */
49 MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */
52 MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */
53 MV_SATAHC0_REG_BASE = 0x20000,
54 MV_FLASH_CTL = 0x1046c,
55 MV_GPIO_PORT_CTL = 0x104f0,
56 MV_RESET_CFG = 0x180d8,
58 MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ,
59 MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ,
60 MV_SATAHC_ARBTR_REG_SZ = MV_MINOR_REG_AREA_SZ, /* arbiter */
61 MV_PORT_REG_SZ = MV_MINOR_REG_AREA_SZ,
63 MV_USE_Q_DEPTH = ATA_DEF_QUEUE,
66 MV_MAX_Q_DEPTH_MASK = MV_MAX_Q_DEPTH - 1,
68 /* CRQB needs alignment on a 1KB boundary. Size == 1KB
69 * CRPB needs alignment on a 256B boundary. Size == 256B
70 * SG count of 176 leads to MV_PORT_PRIV_DMA_SZ == 4KB
71 * ePRD (SG) entries need alignment on a 16B boundary. Size == 16B
73 MV_CRQB_Q_SZ = (32 * MV_MAX_Q_DEPTH),
74 MV_CRPB_Q_SZ = (8 * MV_MAX_Q_DEPTH),
76 MV_SG_TBL_SZ = (16 * MV_MAX_SG_CT),
77 MV_PORT_PRIV_DMA_SZ = (MV_CRQB_Q_SZ + MV_CRPB_Q_SZ + MV_SG_TBL_SZ),
80 /* == (port / MV_PORTS_PER_HC) to determine HC from 0-7 port */
82 /* == (port % MV_PORTS_PER_HC) to determine hard port from 0-7 port */
86 MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
87 MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
88 MV_COMMON_FLAGS = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
89 ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
91 MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE,
93 CRQB_FLAG_READ = (1 << 0),
95 CRQB_CMD_ADDR_SHIFT = 8,
96 CRQB_CMD_CS = (0x2 << 11),
97 CRQB_CMD_LAST = (1 << 15),
99 CRPB_FLAG_STATUS_SHIFT = 8,
101 EPRD_FLAG_END_OF_TBL = (1 << 31),
103 /* PCI interface registers */
105 PCI_COMMAND_OFS = 0xc00,
107 PCI_MAIN_CMD_STS_OFS = 0xd30,
108 STOP_PCI_MASTER = (1 << 2),
109 PCI_MASTER_EMPTY = (1 << 3),
110 GLOB_SFT_RST = (1 << 4),
113 MV_PCI_EXP_ROM_BAR_CTL = 0xd2c,
114 MV_PCI_DISC_TIMER = 0xd04,
115 MV_PCI_MSI_TRIGGER = 0xc38,
116 MV_PCI_SERR_MASK = 0xc28,
117 MV_PCI_XBAR_TMOUT = 0x1d04,
118 MV_PCI_ERR_LOW_ADDRESS = 0x1d40,
119 MV_PCI_ERR_HIGH_ADDRESS = 0x1d44,
120 MV_PCI_ERR_ATTRIBUTE = 0x1d48,
121 MV_PCI_ERR_COMMAND = 0x1d50,
123 PCI_IRQ_CAUSE_OFS = 0x1d58,
124 PCI_IRQ_MASK_OFS = 0x1d5c,
125 PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */
127 HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
128 HC_MAIN_IRQ_MASK_OFS = 0x1d64,
129 PORT0_ERR = (1 << 0), /* shift by port # */
130 PORT0_DONE = (1 << 1), /* shift by port # */
131 HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
132 HC_SHIFT = 9, /* bits 9-17 = HC1's ports */
134 TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */
135 TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */
136 PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */
137 GPIO_INT = (1 << 22),
138 SELF_INT = (1 << 23),
139 TWSI_INT = (1 << 24),
140 HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
141 HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
142 PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
145 /* SATAHC registers */
148 HC_IRQ_CAUSE_OFS = 0x14,
149 CRPB_DMA_DONE = (1 << 0), /* shift by port # */
150 HC_IRQ_COAL = (1 << 4), /* IRQ coalescing */
151 DEV_IRQ = (1 << 8), /* shift by port # */
153 /* Shadow block registers */
155 SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */
158 SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */
159 SATA_ACTIVE_OFS = 0x350,
166 SATA_INTERFACE_CTL = 0x050,
168 MV_M2_PREAMP_MASK = 0x7e0,
172 EDMA_CFG_Q_DEPTH = 0, /* queueing disabled */
173 EDMA_CFG_NCQ = (1 << 5),
174 EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */
175 EDMA_CFG_RD_BRST_EXT = (1 << 11), /* read burst 512B */
176 EDMA_CFG_WR_BUFF_LEN = (1 << 13), /* write buffer 512B */
178 EDMA_ERR_IRQ_CAUSE_OFS = 0x8,
179 EDMA_ERR_IRQ_MASK_OFS = 0xc,
180 EDMA_ERR_D_PAR = (1 << 0),
181 EDMA_ERR_PRD_PAR = (1 << 1),
182 EDMA_ERR_DEV = (1 << 2),
183 EDMA_ERR_DEV_DCON = (1 << 3),
184 EDMA_ERR_DEV_CON = (1 << 4),
185 EDMA_ERR_SERR = (1 << 5),
186 EDMA_ERR_SELF_DIS = (1 << 7),
187 EDMA_ERR_BIST_ASYNC = (1 << 8),
188 EDMA_ERR_CRBQ_PAR = (1 << 9),
189 EDMA_ERR_CRPB_PAR = (1 << 10),
190 EDMA_ERR_INTRL_PAR = (1 << 11),
191 EDMA_ERR_IORDY = (1 << 12),
192 EDMA_ERR_LNK_CTRL_RX = (0xf << 13),
193 EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15),
194 EDMA_ERR_LNK_DATA_RX = (0xf << 17),
195 EDMA_ERR_LNK_CTRL_TX = (0x1f << 21),
196 EDMA_ERR_LNK_DATA_TX = (0x1f << 26),
197 EDMA_ERR_TRANS_PROTO = (1 << 31),
198 EDMA_ERR_FATAL = (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
199 EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR |
200 EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR |
201 EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 |
202 EDMA_ERR_LNK_DATA_RX |
203 EDMA_ERR_LNK_DATA_TX |
204 EDMA_ERR_TRANS_PROTO),
206 EDMA_REQ_Q_BASE_HI_OFS = 0x10,
207 EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */
209 EDMA_REQ_Q_OUT_PTR_OFS = 0x18,
210 EDMA_REQ_Q_PTR_SHIFT = 5,
212 EDMA_RSP_Q_BASE_HI_OFS = 0x1c,
213 EDMA_RSP_Q_IN_PTR_OFS = 0x20,
214 EDMA_RSP_Q_OUT_PTR_OFS = 0x24, /* also contains BASE_LO */
215 EDMA_RSP_Q_PTR_SHIFT = 3,
222 EDMA_IORDY_TMOUT = 0x34,
225 /* Host private flags (hp_flags) */
226 MV_HP_FLAG_MSI = (1 << 0),
227 MV_HP_ERRATA_50XXB0 = (1 << 1),
228 MV_HP_ERRATA_50XXB2 = (1 << 2),
229 MV_HP_ERRATA_60X1B2 = (1 << 3),
230 MV_HP_ERRATA_60X1C0 = (1 << 4),
231 MV_HP_ERRATA_XX42A0 = (1 << 5),
232 MV_HP_50XX = (1 << 6),
233 MV_HP_GEN_IIE = (1 << 7),
235 /* Port private flags (pp_flags) */
236 MV_PP_FLAG_EDMA_EN = (1 << 0),
237 MV_PP_FLAG_EDMA_DS_ACT = (1 << 1),
240 #define IS_50XX(hpriv) ((hpriv)->hp_flags & MV_HP_50XX)
241 #define IS_60XX(hpriv) (((hpriv)->hp_flags & MV_HP_50XX) == 0)
242 #define IS_GEN_I(hpriv) IS_50XX(hpriv)
243 #define IS_GEN_II(hpriv) IS_60XX(hpriv)
244 #define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE)
247 /* Our DMA boundary is determined by an ePRD being unable to handle
248 * anything larger than 64KB
250 MV_DMA_BOUNDARY = 0xffffU,
252 EDMA_REQ_Q_BASE_LO_MASK = 0xfffffc00U,
254 EDMA_RSP_Q_BASE_LO_MASK = 0xffffff00U,
267 /* Command ReQuest Block: 32B */
283 /* Command ResPonse Block: 8B */
290 /* EDMA Physical Region Descriptor (ePRD); A.K.A. SG */
298 struct mv_port_priv {
299 struct mv_crqb *crqb;
301 struct mv_crpb *crpb;
303 struct mv_sg *sg_tbl;
304 dma_addr_t sg_tbl_dma;
306 unsigned req_producer; /* cp of req_in_ptr */
307 unsigned rsp_consumer; /* cp of rsp_out_ptr */
311 struct mv_port_signal {
318 void (*phy_errata)(struct mv_host_priv *hpriv, void __iomem *mmio,
320 void (*enable_leds)(struct mv_host_priv *hpriv, void __iomem *mmio);
321 void (*read_preamp)(struct mv_host_priv *hpriv, int idx,
323 int (*reset_hc)(struct mv_host_priv *hpriv, void __iomem *mmio,
325 void (*reset_flash)(struct mv_host_priv *hpriv, void __iomem *mmio);
326 void (*reset_bus)(struct pci_dev *pdev, void __iomem *mmio);
329 struct mv_host_priv {
331 struct mv_port_signal signal[8];
332 const struct mv_hw_ops *ops;
335 static void mv_irq_clear(struct ata_port *ap);
336 static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
337 static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
338 static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
339 static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
340 static void mv_phy_reset(struct ata_port *ap);
341 static void __mv_phy_reset(struct ata_port *ap, int can_sleep);
342 static void mv_host_stop(struct ata_host_set *host_set);
343 static int mv_port_start(struct ata_port *ap);
344 static void mv_port_stop(struct ata_port *ap);
345 static void mv_qc_prep(struct ata_queued_cmd *qc);
346 static void mv_qc_prep_iie(struct ata_queued_cmd *qc);
347 static unsigned int mv_qc_issue(struct ata_queued_cmd *qc);
348 static irqreturn_t mv_interrupt(int irq, void *dev_instance,
349 struct pt_regs *regs);
350 static void mv_eng_timeout(struct ata_port *ap);
351 static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
353 static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
355 static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio);
356 static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx,
358 static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
360 static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
361 static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio);
363 static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
365 static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio);
366 static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
368 static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
370 static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
371 static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio);
372 static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
373 unsigned int port_no);
374 static void mv_stop_and_reset(struct ata_port *ap);
376 static struct scsi_host_template mv_sht = {
377 .module = THIS_MODULE,
379 .ioctl = ata_scsi_ioctl,
380 .queuecommand = ata_scsi_queuecmd,
381 .eh_timed_out = ata_scsi_timed_out,
382 .eh_strategy_handler = ata_scsi_error,
383 .can_queue = MV_USE_Q_DEPTH,
384 .this_id = ATA_SHT_THIS_ID,
385 .sg_tablesize = MV_MAX_SG_CT / 2,
386 .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
387 .emulated = ATA_SHT_EMULATED,
388 .use_clustering = ATA_SHT_USE_CLUSTERING,
389 .proc_name = DRV_NAME,
390 .dma_boundary = MV_DMA_BOUNDARY,
391 .slave_configure = ata_scsi_slave_config,
392 .bios_param = ata_std_bios_param,
395 static const struct ata_port_operations mv5_ops = {
396 .port_disable = ata_port_disable,
398 .tf_load = ata_tf_load,
399 .tf_read = ata_tf_read,
400 .check_status = ata_check_status,
401 .exec_command = ata_exec_command,
402 .dev_select = ata_std_dev_select,
404 .phy_reset = mv_phy_reset,
406 .qc_prep = mv_qc_prep,
407 .qc_issue = mv_qc_issue,
409 .eng_timeout = mv_eng_timeout,
411 .irq_handler = mv_interrupt,
412 .irq_clear = mv_irq_clear,
414 .scr_read = mv5_scr_read,
415 .scr_write = mv5_scr_write,
417 .port_start = mv_port_start,
418 .port_stop = mv_port_stop,
419 .host_stop = mv_host_stop,
422 static const struct ata_port_operations mv6_ops = {
423 .port_disable = ata_port_disable,
425 .tf_load = ata_tf_load,
426 .tf_read = ata_tf_read,
427 .check_status = ata_check_status,
428 .exec_command = ata_exec_command,
429 .dev_select = ata_std_dev_select,
431 .phy_reset = mv_phy_reset,
433 .qc_prep = mv_qc_prep,
434 .qc_issue = mv_qc_issue,
436 .eng_timeout = mv_eng_timeout,
438 .irq_handler = mv_interrupt,
439 .irq_clear = mv_irq_clear,
441 .scr_read = mv_scr_read,
442 .scr_write = mv_scr_write,
444 .port_start = mv_port_start,
445 .port_stop = mv_port_stop,
446 .host_stop = mv_host_stop,
449 static const struct ata_port_operations mv_iie_ops = {
450 .port_disable = ata_port_disable,
452 .tf_load = ata_tf_load,
453 .tf_read = ata_tf_read,
454 .check_status = ata_check_status,
455 .exec_command = ata_exec_command,
456 .dev_select = ata_std_dev_select,
458 .phy_reset = mv_phy_reset,
460 .qc_prep = mv_qc_prep_iie,
461 .qc_issue = mv_qc_issue,
463 .eng_timeout = mv_eng_timeout,
465 .irq_handler = mv_interrupt,
466 .irq_clear = mv_irq_clear,
468 .scr_read = mv_scr_read,
469 .scr_write = mv_scr_write,
471 .port_start = mv_port_start,
472 .port_stop = mv_port_stop,
473 .host_stop = mv_host_stop,
476 static const struct ata_port_info mv_port_info[] = {
479 .host_flags = MV_COMMON_FLAGS,
480 .pio_mask = 0x1f, /* pio0-4 */
481 .udma_mask = 0x7f, /* udma0-6 */
482 .port_ops = &mv5_ops,
486 .host_flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
487 .pio_mask = 0x1f, /* pio0-4 */
488 .udma_mask = 0x7f, /* udma0-6 */
489 .port_ops = &mv5_ops,
493 .host_flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC),
494 .pio_mask = 0x1f, /* pio0-4 */
495 .udma_mask = 0x7f, /* udma0-6 */
496 .port_ops = &mv5_ops,
500 .host_flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
501 .pio_mask = 0x1f, /* pio0-4 */
502 .udma_mask = 0x7f, /* udma0-6 */
503 .port_ops = &mv6_ops,
507 .host_flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
509 .pio_mask = 0x1f, /* pio0-4 */
510 .udma_mask = 0x7f, /* udma0-6 */
511 .port_ops = &mv6_ops,
515 .host_flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS),
516 .pio_mask = 0x1f, /* pio0-4 */
517 .udma_mask = 0x7f, /* udma0-6 */
518 .port_ops = &mv_iie_ops,
522 .host_flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS |
524 .pio_mask = 0x1f, /* pio0-4 */
525 .udma_mask = 0x7f, /* udma0-6 */
526 .port_ops = &mv_iie_ops,
530 static const struct pci_device_id mv_pci_tbl[] = {
531 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5040), 0, 0, chip_504x},
532 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5041), 0, 0, chip_504x},
533 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5080), 0, 0, chip_5080},
534 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5081), 0, 0, chip_508x},
536 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6040), 0, 0, chip_604x},
537 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6041), 0, 0, chip_604x},
538 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6042), 0, 0, chip_6042},
539 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6080), 0, 0, chip_608x},
540 {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6081), 0, 0, chip_608x},
542 {PCI_DEVICE(PCI_VENDOR_ID_ADAPTEC2, 0x0241), 0, 0, chip_604x},
543 {} /* terminate list */
546 static struct pci_driver mv_pci_driver = {
548 .id_table = mv_pci_tbl,
549 .probe = mv_init_one,
550 .remove = ata_pci_remove_one,
553 static const struct mv_hw_ops mv5xxx_ops = {
554 .phy_errata = mv5_phy_errata,
555 .enable_leds = mv5_enable_leds,
556 .read_preamp = mv5_read_preamp,
557 .reset_hc = mv5_reset_hc,
558 .reset_flash = mv5_reset_flash,
559 .reset_bus = mv5_reset_bus,
562 static const struct mv_hw_ops mv6xxx_ops = {
563 .phy_errata = mv6_phy_errata,
564 .enable_leds = mv6_enable_leds,
565 .read_preamp = mv6_read_preamp,
566 .reset_hc = mv6_reset_hc,
567 .reset_flash = mv6_reset_flash,
568 .reset_bus = mv_reset_pci_bus,
574 static int msi; /* Use PCI msi; either zero (off, default) or non-zero */
581 static inline void writelfl(unsigned long data, void __iomem *addr)
584 (void) readl(addr); /* flush to avoid PCI posted write */
587 static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc)
589 return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ));
592 static inline unsigned int mv_hc_from_port(unsigned int port)
594 return port >> MV_PORT_HC_SHIFT;
597 static inline unsigned int mv_hardport_from_port(unsigned int port)
599 return port & MV_PORT_MASK;
602 static inline void __iomem *mv_hc_base_from_port(void __iomem *base,
605 return mv_hc_base(base, mv_hc_from_port(port));
608 static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port)
610 return mv_hc_base_from_port(base, port) +
611 MV_SATAHC_ARBTR_REG_SZ +
612 (mv_hardport_from_port(port) * MV_PORT_REG_SZ);
615 static inline void __iomem *mv_ap_base(struct ata_port *ap)
617 return mv_port_base(ap->host_set->mmio_base, ap->port_no);
620 static inline int mv_get_hc_count(unsigned long host_flags)
622 return ((host_flags & MV_FLAG_DUAL_HC) ? 2 : 1);
625 static void mv_irq_clear(struct ata_port *ap)
630 * mv_start_dma - Enable eDMA engine
631 * @base: port base address
632 * @pp: port private data
634 * Verify the local cache of the eDMA state is accurate with a
638 * Inherited from caller.
640 static void mv_start_dma(void __iomem *base, struct mv_port_priv *pp)
642 if (!(MV_PP_FLAG_EDMA_EN & pp->pp_flags)) {
643 writelfl(EDMA_EN, base + EDMA_CMD_OFS);
644 pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
646 WARN_ON(!(EDMA_EN & readl(base + EDMA_CMD_OFS)));
650 * mv_stop_dma - Disable eDMA engine
651 * @ap: ATA channel to manipulate
653 * Verify the local cache of the eDMA state is accurate with a
657 * Inherited from caller.
659 static void mv_stop_dma(struct ata_port *ap)
661 void __iomem *port_mmio = mv_ap_base(ap);
662 struct mv_port_priv *pp = ap->private_data;
666 if (MV_PP_FLAG_EDMA_EN & pp->pp_flags) {
667 /* Disable EDMA if active. The disable bit auto clears.
669 writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
670 pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
672 WARN_ON(EDMA_EN & readl(port_mmio + EDMA_CMD_OFS));
675 /* now properly wait for the eDMA to stop */
676 for (i = 1000; i > 0; i--) {
677 reg = readl(port_mmio + EDMA_CMD_OFS);
678 if (!(EDMA_EN & reg)) {
685 printk(KERN_ERR "ata%u: Unable to stop eDMA\n", ap->id);
686 /* FIXME: Consider doing a reset here to recover */
691 static void mv_dump_mem(void __iomem *start, unsigned bytes)
694 for (b = 0; b < bytes; ) {
695 DPRINTK("%p: ", start + b);
696 for (w = 0; b < bytes && w < 4; w++) {
697 printk("%08x ",readl(start + b));
705 static void mv_dump_pci_cfg(struct pci_dev *pdev, unsigned bytes)
710 for (b = 0; b < bytes; ) {
711 DPRINTK("%02x: ", b);
712 for (w = 0; b < bytes && w < 4; w++) {
713 (void) pci_read_config_dword(pdev,b,&dw);
721 static void mv_dump_all_regs(void __iomem *mmio_base, int port,
722 struct pci_dev *pdev)
725 void __iomem *hc_base = mv_hc_base(mmio_base,
726 port >> MV_PORT_HC_SHIFT);
727 void __iomem *port_base;
728 int start_port, num_ports, p, start_hc, num_hcs, hc;
731 start_hc = start_port = 0;
732 num_ports = 8; /* shld be benign for 4 port devs */
735 start_hc = port >> MV_PORT_HC_SHIFT;
737 num_ports = num_hcs = 1;
739 DPRINTK("All registers for port(s) %u-%u:\n", start_port,
740 num_ports > 1 ? num_ports - 1 : start_port);
743 DPRINTK("PCI config space regs:\n");
744 mv_dump_pci_cfg(pdev, 0x68);
746 DPRINTK("PCI regs:\n");
747 mv_dump_mem(mmio_base+0xc00, 0x3c);
748 mv_dump_mem(mmio_base+0xd00, 0x34);
749 mv_dump_mem(mmio_base+0xf00, 0x4);
750 mv_dump_mem(mmio_base+0x1d00, 0x6c);
751 for (hc = start_hc; hc < start_hc + num_hcs; hc++) {
752 hc_base = mv_hc_base(mmio_base, port >> MV_PORT_HC_SHIFT);
753 DPRINTK("HC regs (HC %i):\n", hc);
754 mv_dump_mem(hc_base, 0x1c);
756 for (p = start_port; p < start_port + num_ports; p++) {
757 port_base = mv_port_base(mmio_base, p);
758 DPRINTK("EDMA regs (port %i):\n",p);
759 mv_dump_mem(port_base, 0x54);
760 DPRINTK("SATA regs (port %i):\n",p);
761 mv_dump_mem(port_base+0x300, 0x60);
766 static unsigned int mv_scr_offset(unsigned int sc_reg_in)
774 ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32));
777 ofs = SATA_ACTIVE_OFS; /* active is not with the others */
786 static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
788 unsigned int ofs = mv_scr_offset(sc_reg_in);
790 if (0xffffffffU != ofs) {
791 return readl(mv_ap_base(ap) + ofs);
797 static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
799 unsigned int ofs = mv_scr_offset(sc_reg_in);
801 if (0xffffffffU != ofs) {
802 writelfl(val, mv_ap_base(ap) + ofs);
807 * mv_host_stop - Host specific cleanup/stop routine.
808 * @host_set: host data structure
810 * Disable ints, cleanup host memory, call general purpose
814 * Inherited from caller.
816 static void mv_host_stop(struct ata_host_set *host_set)
818 struct mv_host_priv *hpriv = host_set->private_data;
819 struct pci_dev *pdev = to_pci_dev(host_set->dev);
821 if (hpriv->hp_flags & MV_HP_FLAG_MSI) {
822 pci_disable_msi(pdev);
827 ata_host_stop(host_set);
830 static inline void mv_priv_free(struct mv_port_priv *pp, struct device *dev)
832 dma_free_coherent(dev, MV_PORT_PRIV_DMA_SZ, pp->crpb, pp->crpb_dma);
835 static void mv_edma_cfg(struct mv_host_priv *hpriv, void __iomem *port_mmio)
837 u32 cfg = readl(port_mmio + EDMA_CFG_OFS);
839 /* set up non-NCQ EDMA configuration */
840 cfg &= ~0x1f; /* clear queue depth */
841 cfg &= ~EDMA_CFG_NCQ; /* clear NCQ mode */
842 cfg &= ~(1 << 9); /* disable equeue */
845 cfg |= (1 << 8); /* enab config burst size mask */
847 else if (IS_GEN_II(hpriv))
848 cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN;
850 else if (IS_GEN_IIE(hpriv)) {
851 cfg |= (1 << 23); /* dis RX PM port mask */
852 cfg &= ~(1 << 16); /* dis FIS-based switching (for now) */
853 cfg &= ~(1 << 19); /* dis 128-entry queue (for now?) */
854 cfg |= (1 << 18); /* enab early completion */
855 cfg |= (1 << 17); /* enab host q cache */
856 cfg |= (1 << 22); /* enab cutthrough */
859 writelfl(cfg, port_mmio + EDMA_CFG_OFS);
863 * mv_port_start - Port specific init/start routine.
864 * @ap: ATA channel to manipulate
866 * Allocate and point to DMA memory, init port private memory,
870 * Inherited from caller.
872 static int mv_port_start(struct ata_port *ap)
874 struct device *dev = ap->host_set->dev;
875 struct mv_host_priv *hpriv = ap->host_set->private_data;
876 struct mv_port_priv *pp;
877 void __iomem *port_mmio = mv_ap_base(ap);
882 pp = kmalloc(sizeof(*pp), GFP_KERNEL);
885 memset(pp, 0, sizeof(*pp));
887 mem = dma_alloc_coherent(dev, MV_PORT_PRIV_DMA_SZ, &mem_dma,
891 memset(mem, 0, MV_PORT_PRIV_DMA_SZ);
893 rc = ata_pad_alloc(ap, dev);
897 /* First item in chunk of DMA memory:
898 * 32-slot command request table (CRQB), 32 bytes each in size
901 pp->crqb_dma = mem_dma;
903 mem_dma += MV_CRQB_Q_SZ;
906 * 32-slot command response table (CRPB), 8 bytes each in size
909 pp->crpb_dma = mem_dma;
911 mem_dma += MV_CRPB_Q_SZ;
914 * Table of scatter-gather descriptors (ePRD), 16 bytes each
917 pp->sg_tbl_dma = mem_dma;
919 mv_edma_cfg(hpriv, port_mmio);
921 writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS);
922 writelfl(pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK,
923 port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
925 if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
926 writelfl(pp->crqb_dma & 0xffffffff,
927 port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
929 writelfl(0, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS);
931 writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS);
933 if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0)
934 writelfl(pp->crpb_dma & 0xffffffff,
935 port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
937 writelfl(0, port_mmio + EDMA_RSP_Q_IN_PTR_OFS);
939 writelfl(pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK,
940 port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
942 pp->req_producer = pp->rsp_consumer = 0;
944 /* Don't turn on EDMA here...do it before DMA commands only. Else
945 * we'll be unable to send non-data, PIO, etc due to restricted access
948 ap->private_data = pp;
952 mv_priv_free(pp, dev);
960 * mv_port_stop - Port specific cleanup/stop routine.
961 * @ap: ATA channel to manipulate
963 * Stop DMA, cleanup port memory.
966 * This routine uses the host_set lock to protect the DMA stop.
968 static void mv_port_stop(struct ata_port *ap)
970 struct device *dev = ap->host_set->dev;
971 struct mv_port_priv *pp = ap->private_data;
974 spin_lock_irqsave(&ap->host_set->lock, flags);
976 spin_unlock_irqrestore(&ap->host_set->lock, flags);
978 ap->private_data = NULL;
979 ata_pad_free(ap, dev);
980 mv_priv_free(pp, dev);
985 * mv_fill_sg - Fill out the Marvell ePRD (scatter gather) entries
986 * @qc: queued command whose SG list to source from
988 * Populate the SG list and mark the last entry.
991 * Inherited from caller.
993 static void mv_fill_sg(struct ata_queued_cmd *qc)
995 struct mv_port_priv *pp = qc->ap->private_data;
997 struct scatterlist *sg;
999 ata_for_each_sg(sg, qc) {
1001 u32 sg_len, len, offset;
1003 addr = sg_dma_address(sg);
1004 sg_len = sg_dma_len(sg);
1007 offset = addr & MV_DMA_BOUNDARY;
1009 if ((offset + sg_len) > 0x10000)
1010 len = 0x10000 - offset;
1012 pp->sg_tbl[i].addr = cpu_to_le32(addr & 0xffffffff);
1013 pp->sg_tbl[i].addr_hi = cpu_to_le32((addr >> 16) >> 16);
1014 pp->sg_tbl[i].flags_size = cpu_to_le32(len);
1019 if (!sg_len && ata_sg_is_last(sg, qc))
1020 pp->sg_tbl[i].flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL);
1027 static inline unsigned mv_inc_q_index(unsigned *index)
1029 *index = (*index + 1) & MV_MAX_Q_DEPTH_MASK;
1033 static inline void mv_crqb_pack_cmd(u16 *cmdw, u8 data, u8 addr, unsigned last)
1035 *cmdw = data | (addr << CRQB_CMD_ADDR_SHIFT) | CRQB_CMD_CS |
1036 (last ? CRQB_CMD_LAST : 0);
1040 * mv_qc_prep - Host specific command preparation.
1041 * @qc: queued command to prepare
1043 * This routine simply redirects to the general purpose routine
1044 * if command is not DMA. Else, it handles prep of the CRQB
1045 * (command request block), does some sanity checking, and calls
1046 * the SG load routine.
1049 * Inherited from caller.
1051 static void mv_qc_prep(struct ata_queued_cmd *qc)
1053 struct ata_port *ap = qc->ap;
1054 struct mv_port_priv *pp = ap->private_data;
1056 struct ata_taskfile *tf;
1059 if (ATA_PROT_DMA != qc->tf.protocol)
1062 /* the req producer index should be the same as we remember it */
1063 WARN_ON(((readl(mv_ap_base(qc->ap) + EDMA_REQ_Q_IN_PTR_OFS) >>
1064 EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
1067 /* Fill in command request block
1069 if (!(qc->tf.flags & ATA_TFLAG_WRITE))
1070 flags |= CRQB_FLAG_READ;
1071 WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
1072 flags |= qc->tag << CRQB_TAG_SHIFT;
1074 pp->crqb[pp->req_producer].sg_addr =
1075 cpu_to_le32(pp->sg_tbl_dma & 0xffffffff);
1076 pp->crqb[pp->req_producer].sg_addr_hi =
1077 cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16);
1078 pp->crqb[pp->req_producer].ctrl_flags = cpu_to_le16(flags);
1080 cw = &pp->crqb[pp->req_producer].ata_cmd[0];
1083 /* Sadly, the CRQB cannot accomodate all registers--there are
1084 * only 11 bytes...so we must pick and choose required
1085 * registers based on the command. So, we drop feature and
1086 * hob_feature for [RW] DMA commands, but they are needed for
1087 * NCQ. NCQ will drop hob_nsect.
1089 switch (tf->command) {
1091 case ATA_CMD_READ_EXT:
1093 case ATA_CMD_WRITE_EXT:
1094 case ATA_CMD_WRITE_FUA_EXT:
1095 mv_crqb_pack_cmd(cw++, tf->hob_nsect, ATA_REG_NSECT, 0);
1097 #ifdef LIBATA_NCQ /* FIXME: remove this line when NCQ added */
1098 case ATA_CMD_FPDMA_READ:
1099 case ATA_CMD_FPDMA_WRITE:
1100 mv_crqb_pack_cmd(cw++, tf->hob_feature, ATA_REG_FEATURE, 0);
1101 mv_crqb_pack_cmd(cw++, tf->feature, ATA_REG_FEATURE, 0);
1103 #endif /* FIXME: remove this line when NCQ added */
1105 /* The only other commands EDMA supports in non-queued and
1106 * non-NCQ mode are: [RW] STREAM DMA and W DMA FUA EXT, none
1107 * of which are defined/used by Linux. If we get here, this
1108 * driver needs work.
1110 * FIXME: modify libata to give qc_prep a return value and
1111 * return error here.
1113 BUG_ON(tf->command);
1116 mv_crqb_pack_cmd(cw++, tf->nsect, ATA_REG_NSECT, 0);
1117 mv_crqb_pack_cmd(cw++, tf->hob_lbal, ATA_REG_LBAL, 0);
1118 mv_crqb_pack_cmd(cw++, tf->lbal, ATA_REG_LBAL, 0);
1119 mv_crqb_pack_cmd(cw++, tf->hob_lbam, ATA_REG_LBAM, 0);
1120 mv_crqb_pack_cmd(cw++, tf->lbam, ATA_REG_LBAM, 0);
1121 mv_crqb_pack_cmd(cw++, tf->hob_lbah, ATA_REG_LBAH, 0);
1122 mv_crqb_pack_cmd(cw++, tf->lbah, ATA_REG_LBAH, 0);
1123 mv_crqb_pack_cmd(cw++, tf->device, ATA_REG_DEVICE, 0);
1124 mv_crqb_pack_cmd(cw++, tf->command, ATA_REG_CMD, 1); /* last */
1126 if (!(qc->flags & ATA_QCFLAG_DMAMAP))
1132 * mv_qc_prep_iie - Host specific command preparation.
1133 * @qc: queued command to prepare
1135 * This routine simply redirects to the general purpose routine
1136 * if command is not DMA. Else, it handles prep of the CRQB
1137 * (command request block), does some sanity checking, and calls
1138 * the SG load routine.
1141 * Inherited from caller.
1143 static void mv_qc_prep_iie(struct ata_queued_cmd *qc)
1145 struct ata_port *ap = qc->ap;
1146 struct mv_port_priv *pp = ap->private_data;
1147 struct mv_crqb_iie *crqb;
1148 struct ata_taskfile *tf;
1151 if (ATA_PROT_DMA != qc->tf.protocol)
1154 /* the req producer index should be the same as we remember it */
1155 WARN_ON(((readl(mv_ap_base(qc->ap) + EDMA_REQ_Q_IN_PTR_OFS) >>
1156 EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
1159 /* Fill in Gen IIE command request block
1161 if (!(qc->tf.flags & ATA_TFLAG_WRITE))
1162 flags |= CRQB_FLAG_READ;
1164 WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
1165 flags |= qc->tag << CRQB_TAG_SHIFT;
1167 crqb = (struct mv_crqb_iie *) &pp->crqb[pp->req_producer];
1168 crqb->addr = cpu_to_le32(pp->sg_tbl_dma & 0xffffffff);
1169 crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16);
1170 crqb->flags = cpu_to_le32(flags);
1173 crqb->ata_cmd[0] = cpu_to_le32(
1174 (tf->command << 16) |
1177 crqb->ata_cmd[1] = cpu_to_le32(
1183 crqb->ata_cmd[2] = cpu_to_le32(
1184 (tf->hob_lbal << 0) |
1185 (tf->hob_lbam << 8) |
1186 (tf->hob_lbah << 16) |
1187 (tf->hob_feature << 24)
1189 crqb->ata_cmd[3] = cpu_to_le32(
1191 (tf->hob_nsect << 8)
1194 if (!(qc->flags & ATA_QCFLAG_DMAMAP))
1200 * mv_qc_issue - Initiate a command to the host
1201 * @qc: queued command to start
1203 * This routine simply redirects to the general purpose routine
1204 * if command is not DMA. Else, it sanity checks our local
1205 * caches of the request producer/consumer indices then enables
1206 * DMA and bumps the request producer index.
1209 * Inherited from caller.
1211 static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
1213 void __iomem *port_mmio = mv_ap_base(qc->ap);
1214 struct mv_port_priv *pp = qc->ap->private_data;
1217 if (ATA_PROT_DMA != qc->tf.protocol) {
1218 /* We're about to send a non-EDMA capable command to the
1219 * port. Turn off EDMA so there won't be problems accessing
1220 * shadow block, etc registers.
1222 mv_stop_dma(qc->ap);
1223 return ata_qc_issue_prot(qc);
1226 in_ptr = readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
1228 /* the req producer index should be the same as we remember it */
1229 WARN_ON(((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
1231 /* until we do queuing, the queue should be empty at this point */
1232 WARN_ON(((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
1233 ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >>
1234 EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK));
1236 mv_inc_q_index(&pp->req_producer); /* now incr producer index */
1238 mv_start_dma(port_mmio, pp);
1240 /* and write the request in pointer to kick the EDMA to life */
1241 in_ptr &= EDMA_REQ_Q_BASE_LO_MASK;
1242 in_ptr |= pp->req_producer << EDMA_REQ_Q_PTR_SHIFT;
1243 writelfl(in_ptr, port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
1249 * mv_get_crpb_status - get status from most recently completed cmd
1250 * @ap: ATA channel to manipulate
1252 * This routine is for use when the port is in DMA mode, when it
1253 * will be using the CRPB (command response block) method of
1254 * returning command completion information. We check indices
1255 * are good, grab status, and bump the response consumer index to
1256 * prove that we're up to date.
1259 * Inherited from caller.
1261 static u8 mv_get_crpb_status(struct ata_port *ap)
1263 void __iomem *port_mmio = mv_ap_base(ap);
1264 struct mv_port_priv *pp = ap->private_data;
1267 out_ptr = readl(port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
1269 /* the response consumer index should be the same as we remember it */
1270 WARN_ON(((out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
1273 /* increment our consumer index... */
1274 pp->rsp_consumer = mv_inc_q_index(&pp->rsp_consumer);
1276 /* and, until we do NCQ, there should only be 1 CRPB waiting */
1277 WARN_ON(((readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS) >>
1278 EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
1281 /* write out our inc'd consumer index so EDMA knows we're caught up */
1282 out_ptr &= EDMA_RSP_Q_BASE_LO_MASK;
1283 out_ptr |= pp->rsp_consumer << EDMA_RSP_Q_PTR_SHIFT;
1284 writelfl(out_ptr, port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
1286 /* Return ATA status register for completed CRPB */
1287 return (pp->crpb[pp->rsp_consumer].flags >> CRPB_FLAG_STATUS_SHIFT);
1291 * mv_err_intr - Handle error interrupts on the port
1292 * @ap: ATA channel to manipulate
1294 * In most cases, just clear the interrupt and move on. However,
1295 * some cases require an eDMA reset, which is done right before
1296 * the COMRESET in mv_phy_reset(). The SERR case requires a
1297 * clear of pending errors in the SATA SERROR register. Finally,
1298 * if the port disabled DMA, update our cached copy to match.
1301 * Inherited from caller.
1303 static void mv_err_intr(struct ata_port *ap)
1305 void __iomem *port_mmio = mv_ap_base(ap);
1306 u32 edma_err_cause, serr = 0;
1308 edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
1310 if (EDMA_ERR_SERR & edma_err_cause) {
1311 serr = scr_read(ap, SCR_ERROR);
1312 scr_write_flush(ap, SCR_ERROR, serr);
1314 if (EDMA_ERR_SELF_DIS & edma_err_cause) {
1315 struct mv_port_priv *pp = ap->private_data;
1316 pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
1318 DPRINTK(KERN_ERR "ata%u: port error; EDMA err cause: 0x%08x "
1319 "SERR: 0x%08x\n", ap->id, edma_err_cause, serr);
1321 /* Clear EDMA now that SERR cleanup done */
1322 writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
1324 /* check for fatal here and recover if needed */
1325 if (EDMA_ERR_FATAL & edma_err_cause) {
1326 mv_stop_and_reset(ap);
1331 * mv_host_intr - Handle all interrupts on the given host controller
1332 * @host_set: host specific structure
1333 * @relevant: port error bits relevant to this host controller
1334 * @hc: which host controller we're to look at
1336 * Read then write clear the HC interrupt status then walk each
1337 * port connected to the HC and see if it needs servicing. Port
1338 * success ints are reported in the HC interrupt status reg, the
1339 * port error ints are reported in the higher level main
1340 * interrupt status register and thus are passed in via the
1341 * 'relevant' argument.
1344 * Inherited from caller.
1346 static void mv_host_intr(struct ata_host_set *host_set, u32 relevant,
1349 void __iomem *mmio = host_set->mmio_base;
1350 void __iomem *hc_mmio = mv_hc_base(mmio, hc);
1351 struct ata_port *ap;
1352 struct ata_queued_cmd *qc;
1354 int shift, port, port0, hard_port, handled;
1355 unsigned int err_mask;
1361 port0 = MV_PORTS_PER_HC;
1364 /* we'll need the HC success int register in most cases */
1365 hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
1367 writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
1370 VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
1371 hc,relevant,hc_irq_cause);
1373 for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
1374 ap = host_set->ports[port];
1375 hard_port = port & MV_PORT_MASK; /* range 0-3 */
1376 handled = 0; /* ensure ata_status is set if handled++ */
1378 if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause) {
1379 /* new CRPB on the queue; just one at a time until NCQ
1381 ata_status = mv_get_crpb_status(ap);
1383 } else if ((DEV_IRQ << hard_port) & hc_irq_cause) {
1384 /* received ATA IRQ; read the status reg to clear INTRQ
1386 ata_status = readb((void __iomem *)
1387 ap->ioaddr.status_addr);
1392 (ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR)))
1395 err_mask = ac_err_mask(ata_status);
1397 shift = port << 1; /* (port * 2) */
1398 if (port >= MV_PORTS_PER_HC) {
1399 shift++; /* skip bit 8 in the HC Main IRQ reg */
1401 if ((PORT0_ERR << shift) & relevant) {
1403 err_mask |= AC_ERR_OTHER;
1407 if (handled && ap) {
1408 qc = ata_qc_from_tag(ap, ap->active_tag);
1410 VPRINTK("port %u IRQ found for qc, "
1411 "ata_status 0x%x\n", port,ata_status);
1412 /* mark qc status appropriately */
1413 if (!(qc->tf.ctl & ATA_NIEN)) {
1414 qc->err_mask |= err_mask;
1415 ata_qc_complete(qc);
1426 * @dev_instance: private data; in this case the host structure
1429 * Read the read only register to determine if any host
1430 * controllers have pending interrupts. If so, call lower level
1431 * routine to handle. Also check for PCI errors which are only
1435 * This routine holds the host_set lock while processing pending
1438 static irqreturn_t mv_interrupt(int irq, void *dev_instance,
1439 struct pt_regs *regs)
1441 struct ata_host_set *host_set = dev_instance;
1442 unsigned int hc, handled = 0, n_hcs;
1443 void __iomem *mmio = host_set->mmio_base;
1446 irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
1448 /* check the cases where we either have nothing pending or have read
1449 * a bogus register value which can indicate HW removal or PCI fault
1451 if (!irq_stat || (0xffffffffU == irq_stat)) {
1455 n_hcs = mv_get_hc_count(host_set->ports[0]->flags);
1456 spin_lock(&host_set->lock);
1458 for (hc = 0; hc < n_hcs; hc++) {
1459 u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT));
1461 mv_host_intr(host_set, relevant, hc);
1465 if (PCI_ERR & irq_stat) {
1466 printk(KERN_ERR DRV_NAME ": PCI ERROR; PCI IRQ cause=0x%08x\n",
1467 readl(mmio + PCI_IRQ_CAUSE_OFS));
1469 DPRINTK("All regs @ PCI error\n");
1470 mv_dump_all_regs(mmio, -1, to_pci_dev(host_set->dev));
1472 writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
1475 spin_unlock(&host_set->lock);
1477 return IRQ_RETVAL(handled);
1480 static void __iomem *mv5_phy_base(void __iomem *mmio, unsigned int port)
1482 void __iomem *hc_mmio = mv_hc_base_from_port(mmio, port);
1483 unsigned long ofs = (mv_hardport_from_port(port) + 1) * 0x100UL;
1485 return hc_mmio + ofs;
1488 static unsigned int mv5_scr_offset(unsigned int sc_reg_in)
1492 switch (sc_reg_in) {
1496 ofs = sc_reg_in * sizeof(u32);
1505 static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in)
1507 void __iomem *mmio = mv5_phy_base(ap->host_set->mmio_base, ap->port_no);
1508 unsigned int ofs = mv5_scr_offset(sc_reg_in);
1510 if (ofs != 0xffffffffU)
1511 return readl(mmio + ofs);
1516 static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
1518 void __iomem *mmio = mv5_phy_base(ap->host_set->mmio_base, ap->port_no);
1519 unsigned int ofs = mv5_scr_offset(sc_reg_in);
1521 if (ofs != 0xffffffffU)
1522 writelfl(val, mmio + ofs);
1525 static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio)
1530 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id);
1532 early_5080 = (pdev->device == 0x5080) && (rev_id == 0);
1535 u32 tmp = readl(mmio + MV_PCI_EXP_ROM_BAR_CTL);
1537 writel(tmp, mmio + MV_PCI_EXP_ROM_BAR_CTL);
1540 mv_reset_pci_bus(pdev, mmio);
1543 static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
1545 writel(0x0fcfffff, mmio + MV_FLASH_CTL);
1548 static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx,
1551 void __iomem *phy_mmio = mv5_phy_base(mmio, idx);
1554 tmp = readl(phy_mmio + MV5_PHY_MODE);
1556 hpriv->signal[idx].pre = tmp & 0x1800; /* bits 12:11 */
1557 hpriv->signal[idx].amps = tmp & 0xe0; /* bits 7:5 */
1560 static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
1564 writel(0, mmio + MV_GPIO_PORT_CTL);
1566 /* FIXME: handle MV_HP_ERRATA_50XXB2 errata */
1568 tmp = readl(mmio + MV_PCI_EXP_ROM_BAR_CTL);
1570 writel(tmp, mmio + MV_PCI_EXP_ROM_BAR_CTL);
1573 static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
1576 void __iomem *phy_mmio = mv5_phy_base(mmio, port);
1577 const u32 mask = (1<<12) | (1<<11) | (1<<7) | (1<<6) | (1<<5);
1579 int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0);
1582 tmp = readl(phy_mmio + MV5_LT_MODE);
1584 writel(tmp, phy_mmio + MV5_LT_MODE);
1586 tmp = readl(phy_mmio + MV5_PHY_CTL);
1589 writel(tmp, phy_mmio + MV5_PHY_CTL);
1592 tmp = readl(phy_mmio + MV5_PHY_MODE);
1594 tmp |= hpriv->signal[port].pre;
1595 tmp |= hpriv->signal[port].amps;
1596 writel(tmp, phy_mmio + MV5_PHY_MODE);
1601 #define ZERO(reg) writel(0, port_mmio + (reg))
1602 static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio,
1605 void __iomem *port_mmio = mv_port_base(mmio, port);
1607 writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
1609 mv_channel_reset(hpriv, mmio, port);
1611 ZERO(0x028); /* command */
1612 writel(0x11f, port_mmio + EDMA_CFG_OFS);
1613 ZERO(0x004); /* timer */
1614 ZERO(0x008); /* irq err cause */
1615 ZERO(0x00c); /* irq err mask */
1616 ZERO(0x010); /* rq bah */
1617 ZERO(0x014); /* rq inp */
1618 ZERO(0x018); /* rq outp */
1619 ZERO(0x01c); /* respq bah */
1620 ZERO(0x024); /* respq outp */
1621 ZERO(0x020); /* respq inp */
1622 ZERO(0x02c); /* test control */
1623 writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
1627 #define ZERO(reg) writel(0, hc_mmio + (reg))
1628 static void mv5_reset_one_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
1631 void __iomem *hc_mmio = mv_hc_base(mmio, hc);
1639 tmp = readl(hc_mmio + 0x20);
1642 writel(tmp, hc_mmio + 0x20);
1646 static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
1649 unsigned int hc, port;
1651 for (hc = 0; hc < n_hc; hc++) {
1652 for (port = 0; port < MV_PORTS_PER_HC; port++)
1653 mv5_reset_hc_port(hpriv, mmio,
1654 (hc * MV_PORTS_PER_HC) + port);
1656 mv5_reset_one_hc(hpriv, mmio, hc);
1663 #define ZERO(reg) writel(0, mmio + (reg))
1664 static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio)
1668 tmp = readl(mmio + MV_PCI_MODE);
1670 writel(tmp, mmio + MV_PCI_MODE);
1672 ZERO(MV_PCI_DISC_TIMER);
1673 ZERO(MV_PCI_MSI_TRIGGER);
1674 writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT);
1675 ZERO(HC_MAIN_IRQ_MASK_OFS);
1676 ZERO(MV_PCI_SERR_MASK);
1677 ZERO(PCI_IRQ_CAUSE_OFS);
1678 ZERO(PCI_IRQ_MASK_OFS);
1679 ZERO(MV_PCI_ERR_LOW_ADDRESS);
1680 ZERO(MV_PCI_ERR_HIGH_ADDRESS);
1681 ZERO(MV_PCI_ERR_ATTRIBUTE);
1682 ZERO(MV_PCI_ERR_COMMAND);
1686 static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio)
1690 mv5_reset_flash(hpriv, mmio);
1692 tmp = readl(mmio + MV_GPIO_PORT_CTL);
1694 tmp |= (1 << 5) | (1 << 6);
1695 writel(tmp, mmio + MV_GPIO_PORT_CTL);
1699 * mv6_reset_hc - Perform the 6xxx global soft reset
1700 * @mmio: base address of the HBA
1702 * This routine only applies to 6xxx parts.
1705 * Inherited from caller.
1707 static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
1710 void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS;
1714 /* Following procedure defined in PCI "main command and status
1718 writel(t | STOP_PCI_MASTER, reg);
1720 for (i = 0; i < 1000; i++) {
1723 if (PCI_MASTER_EMPTY & t) {
1727 if (!(PCI_MASTER_EMPTY & t)) {
1728 printk(KERN_ERR DRV_NAME ": PCI master won't flush\n");
1736 writel(t | GLOB_SFT_RST, reg);
1739 } while (!(GLOB_SFT_RST & t) && (i-- > 0));
1741 if (!(GLOB_SFT_RST & t)) {
1742 printk(KERN_ERR DRV_NAME ": can't set global reset\n");
1747 /* clear reset and *reenable the PCI master* (not mentioned in spec) */
1750 writel(t & ~(GLOB_SFT_RST | STOP_PCI_MASTER), reg);
1753 } while ((GLOB_SFT_RST & t) && (i-- > 0));
1755 if (GLOB_SFT_RST & t) {
1756 printk(KERN_ERR DRV_NAME ": can't clear global reset\n");
1763 static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
1766 void __iomem *port_mmio;
1769 tmp = readl(mmio + MV_RESET_CFG);
1770 if ((tmp & (1 << 0)) == 0) {
1771 hpriv->signal[idx].amps = 0x7 << 8;
1772 hpriv->signal[idx].pre = 0x1 << 5;
1776 port_mmio = mv_port_base(mmio, idx);
1777 tmp = readl(port_mmio + PHY_MODE2);
1779 hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */
1780 hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */
1783 static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio)
1785 writel(0x00000060, mmio + MV_GPIO_PORT_CTL);
1788 static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
1791 void __iomem *port_mmio = mv_port_base(mmio, port);
1793 u32 hp_flags = hpriv->hp_flags;
1795 hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
1797 hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0);
1800 if (fix_phy_mode2) {
1801 m2 = readl(port_mmio + PHY_MODE2);
1804 writel(m2, port_mmio + PHY_MODE2);
1808 m2 = readl(port_mmio + PHY_MODE2);
1809 m2 &= ~((1 << 16) | (1 << 31));
1810 writel(m2, port_mmio + PHY_MODE2);
1815 /* who knows what this magic does */
1816 tmp = readl(port_mmio + PHY_MODE3);
1819 writel(tmp, port_mmio + PHY_MODE3);
1821 if (fix_phy_mode4) {
1824 m4 = readl(port_mmio + PHY_MODE4);
1826 if (hp_flags & MV_HP_ERRATA_60X1B2)
1827 tmp = readl(port_mmio + 0x310);
1829 m4 = (m4 & ~(1 << 1)) | (1 << 0);
1831 writel(m4, port_mmio + PHY_MODE4);
1833 if (hp_flags & MV_HP_ERRATA_60X1B2)
1834 writel(tmp, port_mmio + 0x310);
1837 /* Revert values of pre-emphasis and signal amps to the saved ones */
1838 m2 = readl(port_mmio + PHY_MODE2);
1840 m2 &= ~MV_M2_PREAMP_MASK;
1841 m2 |= hpriv->signal[port].amps;
1842 m2 |= hpriv->signal[port].pre;
1845 /* according to mvSata 3.6.1, some IIE values are fixed */
1846 if (IS_GEN_IIE(hpriv)) {
1851 writel(m2, port_mmio + PHY_MODE2);
1854 static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
1855 unsigned int port_no)
1857 void __iomem *port_mmio = mv_port_base(mmio, port_no);
1859 writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
1861 if (IS_60XX(hpriv)) {
1862 u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL);
1863 ifctl |= (1 << 12) | (1 << 7);
1864 writelfl(ifctl, port_mmio + SATA_INTERFACE_CTL);
1867 udelay(25); /* allow reset propagation */
1869 /* Spec never mentions clearing the bit. Marvell's driver does
1870 * clear the bit, however.
1872 writelfl(0, port_mmio + EDMA_CMD_OFS);
1874 hpriv->ops->phy_errata(hpriv, mmio, port_no);
1880 static void mv_stop_and_reset(struct ata_port *ap)
1882 struct mv_host_priv *hpriv = ap->host_set->private_data;
1883 void __iomem *mmio = ap->host_set->mmio_base;
1887 mv_channel_reset(hpriv, mmio, ap->port_no);
1889 __mv_phy_reset(ap, 0);
1892 static inline void __msleep(unsigned int msec, int can_sleep)
1901 * __mv_phy_reset - Perform eDMA reset followed by COMRESET
1902 * @ap: ATA channel to manipulate
1904 * Part of this is taken from __sata_phy_reset and modified to
1905 * not sleep since this routine gets called from interrupt level.
1908 * Inherited from caller. This is coded to safe to call at
1909 * interrupt level, i.e. it does not sleep.
1911 static void __mv_phy_reset(struct ata_port *ap, int can_sleep)
1913 struct mv_port_priv *pp = ap->private_data;
1914 struct mv_host_priv *hpriv = ap->host_set->private_data;
1915 void __iomem *port_mmio = mv_ap_base(ap);
1916 struct ata_taskfile tf;
1917 struct ata_device *dev = &ap->device[0];
1918 unsigned long timeout;
1922 VPRINTK("ENTER, port %u, mmio 0x%p\n", ap->port_no, port_mmio);
1924 DPRINTK("S-regs after ATA_RST: SStat 0x%08x SErr 0x%08x "
1925 "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS),
1926 mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL));
1928 /* Issue COMRESET via SControl */
1930 scr_write_flush(ap, SCR_CONTROL, 0x301);
1931 __msleep(1, can_sleep);
1933 scr_write_flush(ap, SCR_CONTROL, 0x300);
1934 __msleep(20, can_sleep);
1936 timeout = jiffies + msecs_to_jiffies(200);
1938 sstatus = scr_read(ap, SCR_STATUS) & 0x3;
1939 if ((sstatus == 3) || (sstatus == 0))
1942 __msleep(1, can_sleep);
1943 } while (time_before(jiffies, timeout));
1945 /* work around errata */
1946 if (IS_60XX(hpriv) &&
1947 (sstatus != 0x0) && (sstatus != 0x113) && (sstatus != 0x123) &&
1949 goto comreset_retry;
1951 DPRINTK("S-regs after PHY wake: SStat 0x%08x SErr 0x%08x "
1952 "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS),
1953 mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL));
1955 if (sata_dev_present(ap)) {
1958 printk(KERN_INFO "ata%u: no device found (phy stat %08x)\n",
1959 ap->id, scr_read(ap, SCR_STATUS));
1960 ata_port_disable(ap);
1963 ap->cbl = ATA_CBL_SATA;
1965 /* even after SStatus reflects that device is ready,
1966 * it seems to take a while for link to be fully
1967 * established (and thus Status no longer 0x80/0x7F),
1968 * so we poll a bit for that, here.
1972 u8 drv_stat = ata_check_status(ap);
1973 if ((drv_stat != 0x80) && (drv_stat != 0x7f))
1975 __msleep(500, can_sleep);
1980 tf.lbah = readb((void __iomem *) ap->ioaddr.lbah_addr);
1981 tf.lbam = readb((void __iomem *) ap->ioaddr.lbam_addr);
1982 tf.lbal = readb((void __iomem *) ap->ioaddr.lbal_addr);
1983 tf.nsect = readb((void __iomem *) ap->ioaddr.nsect_addr);
1985 dev->class = ata_dev_classify(&tf);
1986 if (!ata_dev_present(dev)) {
1987 VPRINTK("Port disabled post-sig: No device present.\n");
1988 ata_port_disable(ap);
1991 writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
1993 pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
1998 static void mv_phy_reset(struct ata_port *ap)
2000 __mv_phy_reset(ap, 1);
2004 * mv_eng_timeout - Routine called by libata when SCSI times out I/O
2005 * @ap: ATA channel to manipulate
2007 * Intent is to clear all pending error conditions, reset the
2008 * chip/bus, fail the command, and move on.
2011 * This routine holds the host_set lock while failing the command.
2013 static void mv_eng_timeout(struct ata_port *ap)
2015 struct ata_queued_cmd *qc;
2017 printk(KERN_ERR "ata%u: Entering mv_eng_timeout\n",ap->id);
2018 DPRINTK("All regs @ start of eng_timeout\n");
2019 mv_dump_all_regs(ap->host_set->mmio_base, ap->port_no,
2020 to_pci_dev(ap->host_set->dev));
2022 qc = ata_qc_from_tag(ap, ap->active_tag);
2023 printk(KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n",
2024 ap->host_set->mmio_base, ap, qc, qc->scsicmd,
2025 &qc->scsicmd->cmnd);
2028 mv_stop_and_reset(ap);
2030 qc->err_mask |= AC_ERR_TIMEOUT;
2031 ata_eh_qc_complete(qc);
2035 * mv_port_init - Perform some early initialization on a single port.
2036 * @port: libata data structure storing shadow register addresses
2037 * @port_mmio: base address of the port
2039 * Initialize shadow register mmio addresses, clear outstanding
2040 * interrupts on the port, and unmask interrupts for the future
2041 * start of the port.
2044 * Inherited from caller.
2046 static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio)
2048 unsigned long shd_base = (unsigned long) port_mmio + SHD_BLK_OFS;
2051 /* PIO related setup
2053 port->data_addr = shd_base + (sizeof(u32) * ATA_REG_DATA);
2055 port->feature_addr = shd_base + (sizeof(u32) * ATA_REG_ERR);
2056 port->nsect_addr = shd_base + (sizeof(u32) * ATA_REG_NSECT);
2057 port->lbal_addr = shd_base + (sizeof(u32) * ATA_REG_LBAL);
2058 port->lbam_addr = shd_base + (sizeof(u32) * ATA_REG_LBAM);
2059 port->lbah_addr = shd_base + (sizeof(u32) * ATA_REG_LBAH);
2060 port->device_addr = shd_base + (sizeof(u32) * ATA_REG_DEVICE);
2062 port->command_addr = shd_base + (sizeof(u32) * ATA_REG_STATUS);
2063 /* special case: control/altstatus doesn't have ATA_REG_ address */
2064 port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST_OFS;
2067 port->cmd_addr = port->bmdma_addr = port->scr_addr = 0;
2069 /* Clear any currently outstanding port interrupt conditions */
2070 serr_ofs = mv_scr_offset(SCR_ERROR);
2071 writelfl(readl(port_mmio + serr_ofs), port_mmio + serr_ofs);
2072 writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
2074 /* unmask all EDMA error interrupts */
2075 writelfl(~0, port_mmio + EDMA_ERR_IRQ_MASK_OFS);
2077 VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n",
2078 readl(port_mmio + EDMA_CFG_OFS),
2079 readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS),
2080 readl(port_mmio + EDMA_ERR_IRQ_MASK_OFS));
2083 static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv,
2084 unsigned int board_idx)
2087 u32 hp_flags = hpriv->hp_flags;
2089 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id);
2093 hpriv->ops = &mv5xxx_ops;
2094 hp_flags |= MV_HP_50XX;
2098 hp_flags |= MV_HP_ERRATA_50XXB0;
2101 hp_flags |= MV_HP_ERRATA_50XXB2;
2104 dev_printk(KERN_WARNING, &pdev->dev,
2105 "Applying 50XXB2 workarounds to unknown rev\n");
2106 hp_flags |= MV_HP_ERRATA_50XXB2;
2113 hpriv->ops = &mv5xxx_ops;
2114 hp_flags |= MV_HP_50XX;
2118 hp_flags |= MV_HP_ERRATA_50XXB0;
2121 hp_flags |= MV_HP_ERRATA_50XXB2;
2124 dev_printk(KERN_WARNING, &pdev->dev,
2125 "Applying B2 workarounds to unknown rev\n");
2126 hp_flags |= MV_HP_ERRATA_50XXB2;
2133 hpriv->ops = &mv6xxx_ops;
2137 hp_flags |= MV_HP_ERRATA_60X1B2;
2140 hp_flags |= MV_HP_ERRATA_60X1C0;
2143 dev_printk(KERN_WARNING, &pdev->dev,
2144 "Applying B2 workarounds to unknown rev\n");
2145 hp_flags |= MV_HP_ERRATA_60X1B2;
2152 hpriv->ops = &mv6xxx_ops;
2154 hp_flags |= MV_HP_GEN_IIE;
2158 hp_flags |= MV_HP_ERRATA_XX42A0;
2161 hp_flags |= MV_HP_ERRATA_60X1C0;
2164 dev_printk(KERN_WARNING, &pdev->dev,
2165 "Applying 60X1C0 workarounds to unknown rev\n");
2166 hp_flags |= MV_HP_ERRATA_60X1C0;
2172 printk(KERN_ERR DRV_NAME ": BUG: invalid board index %u\n", board_idx);
2176 hpriv->hp_flags = hp_flags;
2182 * mv_init_host - Perform some early initialization of the host.
2183 * @pdev: host PCI device
2184 * @probe_ent: early data struct representing the host
2186 * If possible, do an early global reset of the host. Then do
2187 * our port init and clear/unmask all/relevant host interrupts.
2190 * Inherited from caller.
2192 static int mv_init_host(struct pci_dev *pdev, struct ata_probe_ent *probe_ent,
2193 unsigned int board_idx)
2195 int rc = 0, n_hc, port, hc;
2196 void __iomem *mmio = probe_ent->mmio_base;
2197 struct mv_host_priv *hpriv = probe_ent->private_data;
2199 /* global interrupt mask */
2200 writel(0, mmio + HC_MAIN_IRQ_MASK_OFS);
2202 rc = mv_chip_id(pdev, hpriv, board_idx);
2206 n_hc = mv_get_hc_count(probe_ent->host_flags);
2207 probe_ent->n_ports = MV_PORTS_PER_HC * n_hc;
2209 for (port = 0; port < probe_ent->n_ports; port++)
2210 hpriv->ops->read_preamp(hpriv, port, mmio);
2212 rc = hpriv->ops->reset_hc(hpriv, mmio, n_hc);
2216 hpriv->ops->reset_flash(hpriv, mmio);
2217 hpriv->ops->reset_bus(pdev, mmio);
2218 hpriv->ops->enable_leds(hpriv, mmio);
2220 for (port = 0; port < probe_ent->n_ports; port++) {
2221 if (IS_60XX(hpriv)) {
2222 void __iomem *port_mmio = mv_port_base(mmio, port);
2224 u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL);
2226 writelfl(ifctl, port_mmio + SATA_INTERFACE_CTL);
2229 hpriv->ops->phy_errata(hpriv, mmio, port);
2232 for (port = 0; port < probe_ent->n_ports; port++) {
2233 void __iomem *port_mmio = mv_port_base(mmio, port);
2234 mv_port_init(&probe_ent->port[port], port_mmio);
2237 for (hc = 0; hc < n_hc; hc++) {
2238 void __iomem *hc_mmio = mv_hc_base(mmio, hc);
2240 VPRINTK("HC%i: HC config=0x%08x HC IRQ cause "
2241 "(before clear)=0x%08x\n", hc,
2242 readl(hc_mmio + HC_CFG_OFS),
2243 readl(hc_mmio + HC_IRQ_CAUSE_OFS));
2245 /* Clear any currently outstanding hc interrupt conditions */
2246 writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
2249 /* Clear any currently outstanding host interrupt conditions */
2250 writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
2252 /* and unmask interrupt generation for host regs */
2253 writelfl(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS);
2254 writelfl(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS);
2256 VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
2257 "PCI int cause/mask=0x%08x/0x%08x\n",
2258 readl(mmio + HC_MAIN_IRQ_CAUSE_OFS),
2259 readl(mmio + HC_MAIN_IRQ_MASK_OFS),
2260 readl(mmio + PCI_IRQ_CAUSE_OFS),
2261 readl(mmio + PCI_IRQ_MASK_OFS));
2268 * mv_print_info - Dump key info to kernel log for perusal.
2269 * @probe_ent: early data struct representing the host
2271 * FIXME: complete this.
2274 * Inherited from caller.
2276 static void mv_print_info(struct ata_probe_ent *probe_ent)
2278 struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
2279 struct mv_host_priv *hpriv = probe_ent->private_data;
2283 /* Use this to determine the HW stepping of the chip so we know
2284 * what errata to workaround
2286 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id);
2288 pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &scc);
2291 else if (scc == 0x01)
2296 dev_printk(KERN_INFO, &pdev->dev,
2297 "%u slots %u ports %s mode IRQ via %s\n",
2298 (unsigned)MV_MAX_Q_DEPTH, probe_ent->n_ports,
2299 scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx");
2303 * mv_init_one - handle a positive probe of a Marvell host
2304 * @pdev: PCI device found
2305 * @ent: PCI device ID entry for the matched host
2308 * Inherited from caller.
2310 static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
2312 static int printed_version = 0;
2313 struct ata_probe_ent *probe_ent = NULL;
2314 struct mv_host_priv *hpriv;
2315 unsigned int board_idx = (unsigned int)ent->driver_data;
2316 void __iomem *mmio_base;
2317 int pci_dev_busy = 0, rc;
2319 if (!printed_version++)
2320 dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
2322 rc = pci_enable_device(pdev);
2327 rc = pci_request_regions(pdev, DRV_NAME);
2333 probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
2334 if (probe_ent == NULL) {
2336 goto err_out_regions;
2339 memset(probe_ent, 0, sizeof(*probe_ent));
2340 probe_ent->dev = pci_dev_to_dev(pdev);
2341 INIT_LIST_HEAD(&probe_ent->node);
2343 mmio_base = pci_iomap(pdev, MV_PRIMARY_BAR, 0);
2344 if (mmio_base == NULL) {
2346 goto err_out_free_ent;
2349 hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
2352 goto err_out_iounmap;
2354 memset(hpriv, 0, sizeof(*hpriv));
2356 probe_ent->sht = mv_port_info[board_idx].sht;
2357 probe_ent->host_flags = mv_port_info[board_idx].host_flags;
2358 probe_ent->pio_mask = mv_port_info[board_idx].pio_mask;
2359 probe_ent->udma_mask = mv_port_info[board_idx].udma_mask;
2360 probe_ent->port_ops = mv_port_info[board_idx].port_ops;
2362 probe_ent->irq = pdev->irq;
2363 probe_ent->irq_flags = SA_SHIRQ;
2364 probe_ent->mmio_base = mmio_base;
2365 probe_ent->private_data = hpriv;
2367 /* initialize adapter */
2368 rc = mv_init_host(pdev, probe_ent, board_idx);
2373 /* Enable interrupts */
2374 if (msi && pci_enable_msi(pdev) == 0) {
2375 hpriv->hp_flags |= MV_HP_FLAG_MSI;
2380 mv_dump_pci_cfg(pdev, 0x68);
2381 mv_print_info(probe_ent);
2383 if (ata_device_add(probe_ent) == 0) {
2384 rc = -ENODEV; /* No devices discovered */
2385 goto err_out_dev_add;
2392 if (MV_HP_FLAG_MSI & hpriv->hp_flags) {
2393 pci_disable_msi(pdev);
2400 pci_iounmap(pdev, mmio_base);
2404 pci_release_regions(pdev);
2406 if (!pci_dev_busy) {
2407 pci_disable_device(pdev);
2413 static int __init mv_init(void)
2415 return pci_module_init(&mv_pci_driver);
2418 static void __exit mv_exit(void)
2420 pci_unregister_driver(&mv_pci_driver);
2423 MODULE_AUTHOR("Brett Russ");
2424 MODULE_DESCRIPTION("SCSI low-level driver for Marvell SATA controllers");
2425 MODULE_LICENSE("GPL");
2426 MODULE_DEVICE_TABLE(pci, mv_pci_tbl);
2427 MODULE_VERSION(DRV_VERSION);
2429 module_param(msi, int, 0444);
2430 MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
2432 module_init(mv_init);
2433 module_exit(mv_exit);