1 /* orinoco.c - (formerly known as dldwd_cs.c and orinoco_cs.c)
3 * A driver for Hermes or Prism 2 chipset based PCMCIA wireless
4 * adaptors, with Lucent/Agere, Intersil or Symbol firmware.
6 * Current maintainers (as of 29 September 2003) are:
7 * Pavel Roskin <proski AT gnu.org>
8 * and David Gibson <hermes AT gibson.dropbear.id.au>
10 * (C) Copyright David Gibson, IBM Corporation 2001-2003.
11 * Copyright (C) 2000 David Gibson, Linuxcare Australia.
12 * With some help from :
13 * Copyright (C) 2001 Jean Tourrilhes, HP Labs
14 * Copyright (C) 2001 Benjamin Herrenschmidt
16 * Based on dummy_cs.c 1.27 2000/06/12 21:27:25
18 * Portions based on wvlan_cs.c 1.0.6, Copyright Andreas Neuhaus <andy
19 * AT fasta.fh-dortmund.de>
20 * http://www.stud.fh-dortmund.de/~andy/wvlan/
22 * The contents of this file are subject to the Mozilla Public License
23 * Version 1.1 (the "License"); you may not use this file except in
24 * compliance with the License. You may obtain a copy of the License
25 * at http://www.mozilla.org/MPL/
27 * Software distributed under the License is distributed on an "AS IS"
28 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
29 * the License for the specific language governing rights and
30 * limitations under the License.
32 * The initial developer of the original code is David A. Hinds
33 * <dahinds AT users.sourceforge.net>. Portions created by David
34 * A. Hinds are Copyright (C) 1999 David A. Hinds. All Rights
37 * Alternatively, the contents of this file may be used under the
38 * terms of the GNU General Public License version 2 (the "GPL"), in
39 * which case the provisions of the GPL are applicable instead of the
40 * above. If you wish to allow the use of your version of this file
41 * only under the terms of the GPL and not to allow others to use your
42 * version of this file under the MPL, indicate your decision by
43 * deleting the provisions above and replace them with the notice and
44 * other provisions required by the GPL. If you do not delete the
45 * provisions above, a recipient may use your version of this file
46 * under either the MPL or the GPL. */
49 * v0.01 -> v0.02 - 21/3/2001 - Jean II
50 * o Allow to use regular ethX device name instead of dldwdX
51 * o Warning on IBSS with ESSID=any for firmware 6.06
52 * o Put proper range.throughput values (optimistic)
53 * o IWSPY support (IOCTL and stat gather in Rx path)
54 * o Allow setting frequency in Ad-Hoc mode
55 * o Disable WEP setting if !has_wep to work on old firmware
57 * o Start adding support for Samsung/Compaq firmware
59 * v0.02 -> v0.03 - 23/3/2001 - Jean II
60 * o Start adding Symbol support - need to check all that
61 * o Fix Prism2/Symbol WEP to accept 128 bits keys
62 * o Add Symbol WEP (add authentication type)
63 * o Add Prism2/Symbol rate
64 * o Add PM timeout (holdover duration)
65 * o Enable "iwconfig eth0 key off" and friends (toggle flags)
66 * o Enable "iwconfig eth0 power unicast/all" (toggle flags)
67 * o Try with an Intel card. It report firmware 1.01, behave like
68 * an antiquated firmware, however on windows it says 2.00. Yuck !
69 * o Workaround firmware bug in allocate buffer (Intel 1.01)
70 * o Finish external renaming to orinoco...
71 * o Testing with various Wavelan firmwares
73 * v0.03 -> v0.04 - 30/3/2001 - Jean II
74 * o Update to Wireless 11 -> add retry limit/lifetime support
75 * o Tested with a D-Link DWL 650 card, fill in firmware support
76 * o Warning on Vcc mismatch (D-Link 3.3v card in Lucent 5v only slot)
77 * o Fixed the Prism2 WEP bugs that I introduced in v0.03 :-(
78 * It works on D-Link *only* after a tcpdump. Weird...
79 * And still doesn't work on Intel card. Grrrr...
80 * o Update the mode after a setport3
81 * o Add preamble setting for Symbol cards (not yet enabled)
82 * o Don't complain as much about Symbol cards...
84 * v0.04 -> v0.04b - 22/4/2001 - David Gibson
85 * o Removed the 'eth' parameter - always use ethXX as the
86 * interface name instead of dldwdXX. The other was racy
88 * o Clean up RID definitions in hermes.h, other cleanups
90 * v0.04b -> v0.04c - 24/4/2001 - Jean II
91 * o Tim Hurley <timster AT seiki.bliztech.com> reported a D-Link card
92 * with vendor 02 and firmware 0.08. Added in the capabilities...
93 * o Tested Lucent firmware 7.28, everything works...
95 * v0.04c -> v0.05 - 3/5/2001 - Benjamin Herrenschmidt
96 * o Spin-off Pcmcia code. This file is renamed orinoco.c,
97 * and orinoco_cs.c now contains only the Pcmcia specific stuff
98 * o Add Airport driver support on top of orinoco.c (see airport.c)
100 * v0.05 -> v0.05a - 4/5/2001 - Jean II
101 * o Revert to old Pcmcia code to fix breakage of Ben's changes...
103 * v0.05a -> v0.05b - 4/5/2001 - Jean II
104 * o add module parameter 'ignore_cis_vcc' for D-Link @ 5V
105 * o D-Link firmware doesn't support multicast. We just print a few
106 * error messages, but otherwise everything works...
107 * o For David : set/getport3 works fine, just upgrade iwpriv...
109 * v0.05b -> v0.05c - 5/5/2001 - Benjamin Herrenschmidt
110 * o Adapt airport.c to latest changes in orinoco.c
111 * o Remove deferred power enabling code
113 * v0.05c -> v0.05d - 5/5/2001 - Jean II
114 * o Workaround to SNAP decapsulate frame from Linksys AP
115 * original patch from : Dong Liu <dliu AT research.bell-labs.com>
116 * (note : the memcmp bug was mine - fixed)
117 * o Remove set_retry stuff, no firmware support it (bloat--).
119 * v0.05d -> v0.06 - 25/5/2001 - Jean II
120 * Original patch from "Hong Lin" <alin AT redhat.com>,
121 * "Ian Kinner" <ikinner AT redhat.com>
122 * and "David Smith" <dsmith AT redhat.com>
123 * o Init of priv->tx_rate_ctrl in firmware specific section.
124 * o Prism2/Symbol rate, upto should be 0xF and not 0x15. Doh !
125 * o Spectrum card always need cor_reset (for every reset)
126 * o Fix cor_reset to not lose bit 7 in the register
127 * o flush_stale_links to remove zombie Pcmcia instances
128 * o Ack previous hermes event before reset
129 * Me (with my little hands)
130 * o Allow orinoco.c to call cor_reset via priv->card_reset_handler
131 * o Add priv->need_card_reset to toggle this feature
132 * o Fix various buglets when setting WEP in Symbol firmware
133 * Now, encryption is fully functional on Symbol cards. Youpi !
135 * v0.06 -> v0.06b - 25/5/2001 - Jean II
136 * o IBSS on Symbol use port_mode = 4. Please don't ask...
138 * v0.06b -> v0.06c - 29/5/2001 - Jean II
139 * o Show first spy address in /proc/net/wireless for IBSS mode as well
141 * v0.06c -> v0.06d - 6/7/2001 - David Gibson
142 * o Change a bunch of KERN_INFO messages to KERN_DEBUG, as per Linus'
143 * wishes to reduce the number of unnecessary messages.
144 * o Removed bogus message on CRC error.
145 * o Merged fixes for v0.08 Prism 2 firmware from William Waghorn
146 * <willwaghorn AT yahoo.co.uk>
147 * o Slight cleanup/re-arrangement of firmware detection code.
149 * v0.06d -> v0.06e - 1/8/2001 - David Gibson
150 * o Removed some redundant global initializers (orinoco_cs.c).
151 * o Added some module metadata
153 * v0.06e -> v0.06f - 14/8/2001 - David Gibson
154 * o Wording fix to license
155 * o Added a 'use_alternate_encaps' module parameter for APs which need an
156 * oui of 00:00:00. We really need a better way of handling this, but
157 * the module flag is better than nothing for now.
159 * v0.06f -> v0.07 - 20/8/2001 - David Gibson
160 * o Removed BAP error retries from hermes_bap_seek(). For Tx we now
161 * let the upper layers handle the retry, we retry explicitly in the
162 * Rx path, but don't make as much noise about it.
163 * o Firmware detection cleanups.
165 * v0.07 -> v0.07a - 1/10/3001 - Jean II
166 * o Add code to read Symbol firmware revision, inspired by latest code
167 * in Spectrum24 by Lee John Keyser-Allen - Thanks Lee !
168 * o Thanks to Jared Valentine <hidden AT xmission.com> for "providing" me
169 * a 3Com card with a recent firmware, fill out Symbol firmware
170 * capabilities of latest rev (2.20), as well as older Symbol cards.
171 * o Disable Power Management in newer Symbol firmware, the API
172 * has changed (documentation needed).
174 * v0.07a -> v0.08 - 3/10/2001 - David Gibson
175 * o Fixed a possible buffer overrun found by the Stanford checker (in
176 * dldwd_ioctl_setiwencode()). Can only be called by root anyway, so not
178 * o Turned has_big_wep on for Intersil cards. That's not true for all of
179 * them but we should at least let the capable ones try.
180 * o Wait for BUSY to clear at the beginning of hermes_bap_seek(). I
181 * realized that my assumption that the driver's serialization
182 * would prevent the BAP being busy on entry was possibly false, because
183 * things other than seeks may make the BAP busy.
184 * o Use "alternate" (oui 00:00:00) encapsulation by default.
185 * Setting use_old_encaps will mimic the old behaviour, but I think we
186 * will be able to eliminate this.
187 * o Don't try to make __initdata const (the version string). This can't
188 * work because of the way the __initdata sectioning works.
189 * o Added MODULE_LICENSE tags.
190 * o Support for PLX (transparent PCMCIA->PCI bridge) cards.
191 * o Changed to using the new type-fascist min/max.
193 * v0.08 -> v0.08a - 9/10/2001 - David Gibson
194 * o Inserted some missing acknowledgements/info into the Changelog.
195 * o Fixed some bugs in the normalization of signal level reporting.
196 * o Fixed bad bug in WEP key handling on Intersil and Symbol firmware,
197 * which led to an instant crash on big-endian machines.
199 * v0.08a -> v0.08b - 20/11/2001 - David Gibson
200 * o Lots of cleanup and bugfixes in orinoco_plx.c
201 * o Cleanup to handling of Tx rate setting.
202 * o Removed support for old encapsulation method.
203 * o Removed old "dldwd" names.
204 * o Split RID constants into a new file hermes_rid.h
205 * o Renamed RID constants to match linux-wlan-ng and prism2.o
206 * o Bugfixes in hermes.c
207 * o Poke the PLX's INTCSR register, so it actually starts
208 * generating interrupts. These cards might actually work now.
209 * o Update to wireless extensions v12 (Jean II)
210 * o Support for tallies and inquire command (Jean II)
211 * o Airport updates for newer PPC kernels (BenH)
213 * v0.08b -> v0.09 - 21/12/2001 - David Gibson
214 * o Some new PCI IDs for PLX cards.
215 * o Removed broken attempt to do ALLMULTI reception. Just use
216 * promiscuous mode instead
217 * o Preliminary work for list-AP (Jean II)
218 * o Airport updates from (BenH)
219 * o Eliminated racy hw_ready stuff
220 * o Fixed generation of fake events in irq handler. This should
221 * finally kill the EIO problems (Jean II & dgibson)
222 * o Fixed breakage of bitrate set/get on Agere firmware (Jean II)
224 * v0.09 -> v0.09a - 2/1/2002 - David Gibson
225 * o Fixed stupid mistake in multicast list handling, triggering
228 * v0.09a -> v0.09b - 16/1/2002 - David Gibson
229 * o Fixed even stupider mistake in new interrupt handling, which
230 * seriously broke things on big-endian machines.
231 * o Removed a bunch of redundant includes and exports.
232 * o Removed a redundant MOD_{INC,DEC}_USE_COUNT pair in airport.c
233 * o Don't attempt to do hardware level multicast reception on
234 * Intersil firmware, just go promisc instead.
235 * o Typo fixed in hermes_issue_cmd()
236 * o Eliminated WIRELESS_SPY #ifdefs
237 * o Status code reported on Tx exceptions
238 * o Moved netif_wake_queue() from ALLOC interrupts to TX and TXEXC
239 * interrupts, which should fix the timeouts we're seeing.
241 * v0.09b -> v0.10 - 25 Feb 2002 - David Gibson
242 * o Removed nested structures used for header parsing, so the
243 * driver should now work without hackery on ARM
244 * o Fix for WEP handling on Intersil (Hawk Newton)
245 * o Eliminated the /proc/hermes/ethXX/regs debugging file. It
246 * was never very useful.
247 * o Make Rx errors less noisy.
249 * v0.10 -> v0.11 - 5 Apr 2002 - David Gibson
250 * o Laid the groundwork in hermes.[ch] for devices which map
251 * into PCI memory space rather than IO space.
252 * o Fixed bug in multicast handling (cleared multicast list when
253 * leaving promiscuous mode).
254 * o Relegated Tx error messages to debug.
255 * o Cleaned up / corrected handling of allocation lengths.
256 * o Set OWNSSID in IBSS mode for WinXP interoperability (jimc).
257 * o Change to using alloc_etherdev() for structure allocations.
258 * o Check for and drop undersized packets.
259 * o Fixed a race in stopping/waking the queue. This should fix
260 * the timeout problems (Pavel Roskin)
261 * o Reverted to netif_wake_queue() on the ALLOC event.
262 * o Fixes for recent Symbol firmwares which lack AP density
265 * v0.11 -> v0.11a - 29 Apr 2002 - David Gibson
266 * o Handle different register spacing, necessary for Prism 2.5
267 * PCI adaptors (Steve Hill).
268 * o Cleaned up initialization of card structures in orinoco_cs
269 * and airport. Removed card->priv field.
270 * o Make response structure optional for hermes_docmd_wait()
272 * o Added PCI id for Nortel emobility to orinoco_plx.c.
273 * o Cleanup to handling of Symbol's allocation bug. (Pavel Roskin)
274 * o Cleanups to firmware capability detection.
275 * o Arrange for orinoco_pci.c to override firmware detection.
276 * We should be able to support the PCI Intersil cards now.
277 * o Cleanup handling of reset_cor and hard_reset (Pavel Roskin).
278 * o Remove erroneous use of USER_BAP in the TxExc handler (Jouni
280 * o Makefile changes for better integration into David Hinds
283 * v0.11a -> v0.11b - 1 May 2002 - David Gibson
284 * o Better error reporting in orinoco_plx_init_one()
285 * o Fixed multiple bad kfree() bugs introduced by the
286 * alloc_orinocodev() changes.
288 * v0.11b -> v0.12 - 19 Jun 2002 - David Gibson
289 * o Support changing the MAC address.
290 * o Correct display of Intersil firmware revision numbers.
291 * o Entirely revised locking scheme. Should be both simpler and
293 * o Merged some common code in orinoco_plx, orinoco_pci and
294 * airport by creating orinoco_default_{open,stop,reset}()
295 * which are used as the dev->open, dev->stop, priv->reset
296 * callbacks if none are specified when alloc_orinocodev() is
298 * o Removed orinoco_plx_interrupt() and orinoco_pci_interrupt().
299 * They didn't do anything.
301 * v0.12 -> v0.12a - 4 Jul 2002 - David Gibson
302 * o Some rearrangement of code.
303 * o Numerous fixups to locking and rest handling, particularly
305 * o This allows open and stop net_device methods to be in
306 * orinoco.c now, rather than in the init modules.
307 * o In orinoco_cs.c link->priv now points to the struct
308 * net_device not to the struct orinoco_private.
309 * o Added a check for undersized SNAP frames, which could cause
312 * v0.12a -> v0.12b - 11 Jul 2002 - David Gibson
313 * o Fix hw->num_init testing code, so num_init is actually
315 * o Fix very stupid bug in orinoco_cs which broke compile with
317 * o Squashed a warning.
319 * v0.12b -> v0.12c - 26 Jul 2002 - David Gibson
320 * o Change to C9X style designated initializers.
321 * o Add support for 3Com AirConnect PCI.
322 * o No longer ignore the hard_reset argument to
323 * alloc_orinocodev(). Oops.
325 * v0.12c -> v0.13beta1 - 13 Sep 2002 - David Gibson
326 * o Revert the broken 0.12* locking scheme and go to a new yet
328 * o Do firmware resets only in orinoco_init() and when waking
329 * the card from hard sleep.
331 * v0.13beta1 -> v0.13 - 27 Sep 2002 - David Gibson
332 * o Re-introduced full resets (via schedule_task()) on Tx
335 * v0.13 -> v0.13a - 30 Sep 2002 - David Gibson
336 * o Minor cleanups to info frame handling. Add basic support
337 * for linkstatus info frames.
338 * o Include required kernel headers in orinoco.h, to avoid
341 * v0.13a -> v0.13b - 10 Feb 2003 - David Gibson
342 * o Implemented hard reset for Airport cards
343 * o Experimental suspend/resume implementation for orinoco_pci
344 * o Abolished /proc debugging support, replaced with a debugging
345 * iwpriv. Now it's ugly and simple instead of ugly and complex.
346 * o Bugfix in hermes.c if the firmware returned a record length
347 * of 0, we could go clobbering memory.
348 * o Bugfix in orinoco_stop() - it used to fail if hw_unavailable
349 * was set, which was usually true on PCMCIA hot removes.
350 * o Track LINKSTATUS messages, silently drop Tx packets before
351 * we are connected (avoids confusing the firmware), and only
352 * give LINKSTATUS printk()s if the status has changed.
354 * v0.13b -> v0.13c - 11 Mar 2003 - David Gibson
355 * o Cleanup: use dev instead of priv in various places.
356 * o Bug fix: Don't ReleaseConfiguration on RESET_PHYSICAL event
357 * if we're in the middle of a (driver initiated) hard reset.
358 * o Bug fix: ETH_ZLEN is supposed to include the header
359 * (Dionysus Blazakis & Manish Karir)
360 * o Convert to using workqueues instead of taskqueues (and
361 * backwards compatibility macros for pre 2.5.41 kernels).
362 * o Drop redundant (I think...) MOD_{INC,DEC}_USE_COUNT in
364 * o New orinoco_tmd.c init module from Joerg Dorchain for
365 * TMD7160 based PCI to PCMCIA bridges (similar to
368 * v0.13c -> v0.13d - 22 Apr 2003 - David Gibson
369 * o Make hw_unavailable a counter, rather than just a flag, this
370 * is necessary to avoid some races (such as a card being
371 * removed in the middle of orinoco_reset().
372 * o Restore Release/RequestConfiguration in the PCMCIA event handler
373 * when dealing with a driver initiated hard reset. This is
374 * necessary to prevent hangs due to a spurious interrupt while
375 * the reset is in progress.
376 * o Clear the 802.11 header when transmitting, even though we
377 * don't use it. This fixes a long standing bug on some
378 * firmwares, which seem to get confused if that isn't done.
379 * o Be less eager to de-encapsulate SNAP frames, only do so if
380 * the OUI is 00:00:00 or 00:00:f8, leave others alone. The old
381 * behaviour broke CDP (Cisco Discovery Protocol).
382 * o Use dev instead of priv for free_irq() as well as
383 * request_irq() (oops).
384 * o Attempt to reset rather than giving up if we get too many
386 * o Changed semantics of __orinoco_down() so it can be called
387 * safely with hw_unavailable set. It also now clears the
388 * linkstatus (since we're going to have to reassociate).
390 * v0.13d -> v0.13e - 12 May 2003 - David Gibson
391 * o Support for post-2.5.68 return values from irq handler.
392 * o Fixed bug where underlength packets would be double counted
393 * in the rx_dropped statistics.
394 * o Provided a module parameter to suppress linkstatus messages.
396 * v0.13e -> v0.14alpha1 - 30 Sep 2003 - David Gibson
397 * o Replaced priv->connected logic with netif_carrier_on/off()
399 * o Remove has_ibss_any and never set the CREATEIBSS RID when
400 * the ESSID is empty. Too many firmwares break if we do.
401 * o 2.6 merges: Replace pdev->slot_name with pci_name(), remove
402 * __devinitdata from PCI ID tables, use free_netdev().
403 * o Enabled shared-key authentication for Agere firmware (from
404 * Robert J. Moore <Robert.J.Moore AT allanbank.com>
405 * o Move netif_wake_queue() (back) to the Tx completion from the
406 * ALLOC event. This seems to prevent/mitigate the rolling
407 * error -110 problems at least on some Intersil firmwares.
408 * Theoretically reduces performance, but I can't measure it.
409 * Patch from Andrew Tridgell <tridge AT samba.org>
411 * v0.14alpha1 -> v0.14alpha2 - 20 Oct 2003 - David Gibson
412 * o Correctly turn off shared-key authentication when requested
413 * (bugfix from Robert J. Moore).
414 * o Correct airport sleep interfaces for current 2.6 kernels.
415 * o Add code for key change without disabling/enabling the MAC
416 * port. This is supposed to allow 802.1x to work sanely, but
417 * doesn't seem to yet.
420 * o New wireless extensions API (patch from Moustafa
421 * Youssef, updated by Jim Carter and Pavel Roskin).
422 * o Handle de-encapsulation within network layer, provide 802.11
423 * headers (patch from Thomas 'Dent' Mirlacher)
424 * o RF monitor mode support
425 * o Fix possible races in SPY handling.
426 * o Disconnect wireless extensions from fundamental configuration.
427 * o (maybe) Software WEP support (patch from Stano Meduna).
428 * o (maybe) Use multiple Tx buffers - driver handling queue
429 * rather than firmware.
432 /* Locking and synchronization:
434 * The basic principle is that everything is serialized through a
435 * single spinlock, priv->lock. The lock is used in user, bh and irq
436 * context, so when taken outside hardirq context it should always be
437 * taken with interrupts disabled. The lock protects both the
438 * hardware and the struct orinoco_private.
440 * Another flag, priv->hw_unavailable indicates that the hardware is
441 * unavailable for an extended period of time (e.g. suspended, or in
442 * the middle of a hard reset). This flag is protected by the
443 * spinlock. All code which touches the hardware should check the
444 * flag after taking the lock, and if it is set, give up on whatever
445 * they are doing and drop the lock again. The orinoco_lock()
446 * function handles this (it unlocks and returns -EBUSY if
447 * hw_unavailable is non-zero).
450 #define DRIVER_NAME "orinoco"
452 #include <linux/config.h>
454 #include <linux/module.h>
455 #include <linux/kernel.h>
456 #include <linux/init.h>
457 #include <linux/ptrace.h>
458 #include <linux/slab.h>
459 #include <linux/string.h>
460 #include <linux/timer.h>
461 #include <linux/ioport.h>
462 #include <linux/netdevice.h>
463 #include <linux/if_arp.h>
464 #include <linux/etherdevice.h>
465 #include <linux/wireless.h>
467 #include <asm/uaccess.h>
469 #include <asm/system.h>
472 #include "hermes_rid.h"
474 #include "ieee802_11.h"
476 /********************************************************************/
477 /* Module information */
478 /********************************************************************/
480 MODULE_AUTHOR("Pavel Roskin <proski@gnu.org> & David Gibson <hermes@gibson.dropbear.id.au>");
481 MODULE_DESCRIPTION("Driver for Lucent Orinoco, Prism II based and similar wireless cards");
482 MODULE_LICENSE("Dual MPL/GPL");
484 /* Level of debugging. Used in the macros in orinoco.h */
486 int orinoco_debug = ORINOCO_DEBUG;
487 module_param(orinoco_debug, int, 0644);
488 MODULE_PARM_DESC(orinoco_debug, "Debug level");
489 EXPORT_SYMBOL(orinoco_debug);
492 static int suppress_linkstatus; /* = 0 */
493 module_param(suppress_linkstatus, bool, 0644);
494 MODULE_PARM_DESC(suppress_linkstatus, "Don't log link status changes");
495 static int ignore_disconnect; /* = 0 */
496 module_param(ignore_disconnect, int, 0644);
497 MODULE_PARM_DESC(ignore_disconnect, "Don't report lost link to the network layer");
499 /********************************************************************/
500 /* Compile time configuration and compatibility stuff */
501 /********************************************************************/
503 /* We do this this way to avoid ifdefs in the actual code */
505 #define SPY_NUMBER(priv) (priv->spy_number)
507 #define SPY_NUMBER(priv) 0
508 #endif /* WIRELESS_SPY */
510 /********************************************************************/
511 /* Internal constants */
512 /********************************************************************/
514 #define ORINOCO_MIN_MTU 256
515 #define ORINOCO_MAX_MTU (IEEE802_11_DATA_LEN - ENCAPS_OVERHEAD)
517 #define SYMBOL_MAX_VER_LEN (14)
520 #define MAX_IRQLOOPS_PER_IRQ 10
521 #define MAX_IRQLOOPS_PER_JIFFY (20000/HZ) /* Based on a guestimate of
522 * how many events the
524 * legitimately generate */
525 #define SMALL_KEY_SIZE 5
526 #define LARGE_KEY_SIZE 13
527 #define TX_NICBUF_SIZE_BUG 1585 /* Bug in Symbol firmware */
529 #define DUMMY_FID 0xFFFF
531 /*#define MAX_MULTICAST(priv) (priv->firmware_type == FIRMWARE_TYPE_AGERE ? \
532 HERMES_MAX_MULTICAST : 0)*/
533 #define MAX_MULTICAST(priv) (HERMES_MAX_MULTICAST)
535 #define ORINOCO_INTEN (HERMES_EV_RX | HERMES_EV_ALLOC \
536 | HERMES_EV_TX | HERMES_EV_TXEXC \
537 | HERMES_EV_WTERR | HERMES_EV_INFO \
538 | HERMES_EV_INFDROP )
540 /********************************************************************/
542 /********************************************************************/
544 /* The frequency of each channel in MHz */
545 static const long channel_frequency[] = {
546 2412, 2417, 2422, 2427, 2432, 2437, 2442,
547 2447, 2452, 2457, 2462, 2467, 2472, 2484
549 #define NUM_CHANNELS ARRAY_SIZE(channel_frequency)
551 /* This tables gives the actual meanings of the bitrate IDs returned
552 * by the firmware. */
554 int bitrate; /* in 100s of kilobits */
556 u16 agere_txratectrl;
557 u16 intersil_txratectrl;
558 } bitrate_table[] = {
559 {110, 1, 3, 15}, /* Entry 0 is the default */
568 #define BITRATE_TABLE_SIZE ARRAY_SIZE(bitrate_table)
570 /********************************************************************/
572 /********************************************************************/
574 struct header_struct {
586 } __attribute__ ((packed));
588 /* 802.2 LLC/SNAP header used for Ethernet encapsulation over 802.11 */
589 u8 encaps_hdr[] = {0xaa, 0xaa, 0x03, 0x00, 0x00, 0x00};
591 #define ENCAPS_OVERHEAD (sizeof(encaps_hdr) + 2)
593 struct hermes_rx_descriptor {
601 } __attribute__ ((packed));
603 /********************************************************************/
604 /* Function prototypes */
605 /********************************************************************/
607 static int orinoco_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
608 static int __orinoco_program_rids(struct net_device *dev);
609 static void __orinoco_set_multicast_list(struct net_device *dev);
611 /********************************************************************/
612 /* Internal helper functions */
613 /********************************************************************/
615 static inline void set_port_type(struct orinoco_private *priv)
617 switch (priv->iw_mode) {
620 priv->createibss = 0;
623 if (priv->prefer_port3) {
625 priv->createibss = 0;
627 priv->port_type = priv->ibss_port;
628 priv->createibss = 1;
632 printk(KERN_ERR "%s: Invalid priv->iw_mode in set_port_type()\n",
637 /********************************************************************/
639 /********************************************************************/
641 static int orinoco_open(struct net_device *dev)
643 struct orinoco_private *priv = netdev_priv(dev);
647 if (orinoco_lock(priv, &flags) != 0)
650 err = __orinoco_up(dev);
655 orinoco_unlock(priv, &flags);
660 int orinoco_stop(struct net_device *dev)
662 struct orinoco_private *priv = netdev_priv(dev);
665 /* We mustn't use orinoco_lock() here, because we need to be
666 able to close the interface even if hw_unavailable is set
667 (e.g. as we're released after a PC Card removal) */
668 spin_lock_irq(&priv->lock);
672 err = __orinoco_down(dev);
674 spin_unlock_irq(&priv->lock);
679 static struct net_device_stats *orinoco_get_stats(struct net_device *dev)
681 struct orinoco_private *priv = netdev_priv(dev);
686 static struct iw_statistics *orinoco_get_wireless_stats(struct net_device *dev)
688 struct orinoco_private *priv = netdev_priv(dev);
689 hermes_t *hw = &priv->hw;
690 struct iw_statistics *wstats = &priv->wstats;
694 if (! netif_device_present(dev)) {
695 printk(KERN_WARNING "%s: get_wireless_stats() called while device not present\n",
697 return NULL; /* FIXME: Can we do better than this? */
700 /* If busy, return the old stats. Returning NULL may cause
701 * the interface to disappear from /proc/net/wireless */
702 if (orinoco_lock(priv, &flags) != 0)
705 /* We can't really wait for the tallies inquiry command to
706 * complete, so we just use the previous results and trigger
707 * a new tallies inquiry command for next time - Jean II */
708 /* FIXME: Really we should wait for the inquiry to come back -
709 * as it is the stats we give don't make a whole lot of sense.
710 * Unfortunately, it's not clear how to do that within the
711 * wireless extensions framework: I think we're in user
712 * context, but a lock seems to be held by the time we get in
713 * here so we're not safe to sleep here. */
714 hermes_inquire(hw, HERMES_INQ_TALLIES);
716 if (priv->iw_mode == IW_MODE_ADHOC) {
717 memset(&wstats->qual, 0, sizeof(wstats->qual));
718 /* If a spy address is defined, we report stats of the
719 * first spy address - Jean II */
720 if (SPY_NUMBER(priv)) {
721 wstats->qual.qual = priv->spy_stat[0].qual;
722 wstats->qual.level = priv->spy_stat[0].level;
723 wstats->qual.noise = priv->spy_stat[0].noise;
724 wstats->qual.updated = priv->spy_stat[0].updated;
728 u16 qual, signal, noise;
729 } __attribute__ ((packed)) cq;
731 err = HERMES_READ_RECORD(hw, USER_BAP,
732 HERMES_RID_COMMSQUALITY, &cq);
735 wstats->qual.qual = (int)le16_to_cpu(cq.qual);
736 wstats->qual.level = (int)le16_to_cpu(cq.signal) - 0x95;
737 wstats->qual.noise = (int)le16_to_cpu(cq.noise) - 0x95;
738 wstats->qual.updated = 7;
742 orinoco_unlock(priv, &flags);
746 static void orinoco_set_multicast_list(struct net_device *dev)
748 struct orinoco_private *priv = netdev_priv(dev);
751 if (orinoco_lock(priv, &flags) != 0) {
752 printk(KERN_DEBUG "%s: orinoco_set_multicast_list() "
753 "called when hw_unavailable\n", dev->name);
757 __orinoco_set_multicast_list(dev);
758 orinoco_unlock(priv, &flags);
761 static int orinoco_change_mtu(struct net_device *dev, int new_mtu)
763 struct orinoco_private *priv = netdev_priv(dev);
765 if ( (new_mtu < ORINOCO_MIN_MTU) || (new_mtu > ORINOCO_MAX_MTU) )
768 if ( (new_mtu + ENCAPS_OVERHEAD + IEEE802_11_HLEN) >
769 (priv->nicbuf_size - ETH_HLEN) )
777 /********************************************************************/
779 /********************************************************************/
781 static int orinoco_xmit(struct sk_buff *skb, struct net_device *dev)
783 struct orinoco_private *priv = netdev_priv(dev);
784 struct net_device_stats *stats = &priv->stats;
785 hermes_t *hw = &priv->hw;
787 u16 txfid = priv->txfid;
790 int len, data_len, data_off;
791 struct hermes_tx_descriptor desc;
794 TRACE_ENTER(dev->name);
796 if (! netif_running(dev)) {
797 printk(KERN_ERR "%s: Tx on stopped device!\n",
799 TRACE_EXIT(dev->name);
803 if (netif_queue_stopped(dev)) {
804 printk(KERN_DEBUG "%s: Tx while transmitter busy!\n",
806 TRACE_EXIT(dev->name);
810 if (orinoco_lock(priv, &flags) != 0) {
811 printk(KERN_ERR "%s: orinoco_xmit() called while hw_unavailable\n",
813 TRACE_EXIT(dev->name);
817 if (! netif_carrier_ok(dev)) {
818 /* Oops, the firmware hasn't established a connection,
819 silently drop the packet (this seems to be the
822 orinoco_unlock(priv, &flags);
824 TRACE_EXIT(dev->name);
828 /* Length of the packet body */
829 /* FIXME: what if the skb is smaller than this? */
830 len = max_t(int,skb->len - ETH_HLEN, ETH_ZLEN - ETH_HLEN);
832 eh = (struct ethhdr *)skb->data;
834 memset(&desc, 0, sizeof(desc));
835 desc.tx_control = cpu_to_le16(HERMES_TXCTRL_TX_OK | HERMES_TXCTRL_TX_EX);
836 err = hermes_bap_pwrite(hw, USER_BAP, &desc, sizeof(desc), txfid, 0);
839 printk(KERN_ERR "%s: Error %d writing Tx descriptor "
840 "to BAP\n", dev->name, err);
845 /* Clear the 802.11 header and data length fields - some
846 * firmwares (e.g. Lucent/Agere 8.xx) appear to get confused
847 * if this isn't done. */
848 hermes_clear_words(hw, HERMES_DATA0,
849 HERMES_802_3_OFFSET - HERMES_802_11_OFFSET);
851 /* Encapsulate Ethernet-II frames */
852 if (ntohs(eh->h_proto) > ETH_DATA_LEN) { /* Ethernet-II frame */
853 struct header_struct hdr;
855 data_off = HERMES_802_3_OFFSET + sizeof(hdr);
856 p = skb->data + ETH_HLEN;
859 memcpy(hdr.dest, eh->h_dest, ETH_ALEN);
860 memcpy(hdr.src, eh->h_source, ETH_ALEN);
861 hdr.len = htons(data_len + ENCAPS_OVERHEAD);
864 memcpy(&hdr.dsap, &encaps_hdr, sizeof(encaps_hdr));
866 hdr.ethertype = eh->h_proto;
867 err = hermes_bap_pwrite(hw, USER_BAP, &hdr, sizeof(hdr),
868 txfid, HERMES_802_3_OFFSET);
871 printk(KERN_ERR "%s: Error %d writing packet "
872 "header to BAP\n", dev->name, err);
876 } else { /* IEEE 802.3 frame */
877 data_len = len + ETH_HLEN;
878 data_off = HERMES_802_3_OFFSET;
882 /* Round up for odd length packets */
883 err = hermes_bap_pwrite(hw, USER_BAP, p, ALIGN(data_len, 2),
886 printk(KERN_ERR "%s: Error %d writing packet to BAP\n",
892 /* Finally, we actually initiate the send */
893 netif_stop_queue(dev);
895 err = hermes_docmd_wait(hw, HERMES_CMD_TX | HERMES_CMD_RECL,
898 netif_start_queue(dev);
899 printk(KERN_ERR "%s: Error %d transmitting packet\n",
905 dev->trans_start = jiffies;
906 stats->tx_bytes += data_off + data_len;
908 orinoco_unlock(priv, &flags);
912 TRACE_EXIT(dev->name);
916 TRACE_EXIT(dev->name);
918 orinoco_unlock(priv, &flags);
922 static void __orinoco_ev_alloc(struct net_device *dev, hermes_t *hw)
924 struct orinoco_private *priv = netdev_priv(dev);
925 u16 fid = hermes_read_regn(hw, ALLOCFID);
927 if (fid != priv->txfid) {
928 if (fid != DUMMY_FID)
929 printk(KERN_WARNING "%s: Allocate event on unexpected fid (%04X)\n",
934 hermes_write_regn(hw, ALLOCFID, DUMMY_FID);
937 static void __orinoco_ev_tx(struct net_device *dev, hermes_t *hw)
939 struct orinoco_private *priv = netdev_priv(dev);
940 struct net_device_stats *stats = &priv->stats;
944 netif_wake_queue(dev);
946 hermes_write_regn(hw, TXCOMPLFID, DUMMY_FID);
949 static void __orinoco_ev_txexc(struct net_device *dev, hermes_t *hw)
951 struct orinoco_private *priv = netdev_priv(dev);
952 struct net_device_stats *stats = &priv->stats;
953 u16 fid = hermes_read_regn(hw, TXCOMPLFID);
954 struct hermes_tx_descriptor desc;
957 if (fid == DUMMY_FID)
958 return; /* Nothing's really happened */
960 err = hermes_bap_pread(hw, IRQ_BAP, &desc, sizeof(desc), fid, 0);
962 printk(KERN_WARNING "%s: Unable to read descriptor on Tx error "
963 "(FID=%04X error %d)\n",
964 dev->name, fid, err);
966 DEBUG(1, "%s: Tx error, status %d\n",
967 dev->name, le16_to_cpu(desc.status));
972 netif_wake_queue(dev);
973 hermes_write_regn(hw, TXCOMPLFID, DUMMY_FID);
976 static void orinoco_tx_timeout(struct net_device *dev)
978 struct orinoco_private *priv = netdev_priv(dev);
979 struct net_device_stats *stats = &priv->stats;
980 struct hermes *hw = &priv->hw;
982 printk(KERN_WARNING "%s: Tx timeout! "
983 "ALLOCFID=%04x, TXCOMPLFID=%04x, EVSTAT=%04x\n",
984 dev->name, hermes_read_regn(hw, ALLOCFID),
985 hermes_read_regn(hw, TXCOMPLFID), hermes_read_regn(hw, EVSTAT));
989 schedule_work(&priv->reset_work);
992 /********************************************************************/
993 /* Rx path (data frames) */
994 /********************************************************************/
996 /* Does the frame have a SNAP header indicating it should be
997 * de-encapsulated to Ethernet-II? */
998 static inline int is_ethersnap(void *_hdr)
1002 /* We de-encapsulate all packets which, a) have SNAP headers
1003 * (i.e. SSAP=DSAP=0xaa and CTRL=0x3 in the 802.2 LLC header
1004 * and where b) the OUI of the SNAP header is 00:00:00 or
1005 * 00:00:f8 - we need both because different APs appear to use
1006 * different OUIs for some reason */
1007 return (memcmp(hdr, &encaps_hdr, 5) == 0)
1008 && ( (hdr[5] == 0x00) || (hdr[5] == 0xf8) );
1011 static inline void orinoco_spy_gather(struct net_device *dev, u_char *mac,
1012 int level, int noise)
1014 struct orinoco_private *priv = netdev_priv(dev);
1017 /* Gather wireless spy statistics: for each packet, compare the
1018 * source address with out list, and if match, get the stats... */
1019 for (i = 0; i < priv->spy_number; i++)
1020 if (!memcmp(mac, priv->spy_address[i], ETH_ALEN)) {
1021 priv->spy_stat[i].level = level - 0x95;
1022 priv->spy_stat[i].noise = noise - 0x95;
1023 priv->spy_stat[i].qual = (level > noise) ? (level - noise) : 0;
1024 priv->spy_stat[i].updated = 7;
1028 static void orinoco_stat_gather(struct net_device *dev,
1029 struct sk_buff *skb,
1030 struct hermes_rx_descriptor *desc)
1032 struct orinoco_private *priv = netdev_priv(dev);
1034 /* Using spy support with lots of Rx packets, like in an
1035 * infrastructure (AP), will really slow down everything, because
1036 * the MAC address must be compared to each entry of the spy list.
1037 * If the user really asks for it (set some address in the
1038 * spy list), we do it, but he will pay the price.
1039 * Note that to get here, you need both WIRELESS_SPY
1040 * compiled in AND some addresses in the list !!!
1042 /* Note : gcc will optimise the whole section away if
1043 * WIRELESS_SPY is not defined... - Jean II */
1044 if (SPY_NUMBER(priv)) {
1045 orinoco_spy_gather(dev, skb->mac.raw + ETH_ALEN,
1046 desc->signal, desc->silence);
1050 static void __orinoco_ev_rx(struct net_device *dev, hermes_t *hw)
1052 struct orinoco_private *priv = netdev_priv(dev);
1053 struct net_device_stats *stats = &priv->stats;
1054 struct iw_statistics *wstats = &priv->wstats;
1055 struct sk_buff *skb = NULL;
1057 int length, data_len, data_off;
1059 struct hermes_rx_descriptor desc;
1060 struct header_struct hdr;
1064 rxfid = hermes_read_regn(hw, RXFID);
1066 err = hermes_bap_pread(hw, IRQ_BAP, &desc, sizeof(desc),
1069 printk(KERN_ERR "%s: error %d reading Rx descriptor. "
1070 "Frame dropped.\n", dev->name, err);
1075 status = le16_to_cpu(desc.status);
1077 if (status & HERMES_RXSTAT_ERR) {
1078 if (status & HERMES_RXSTAT_UNDECRYPTABLE) {
1079 wstats->discard.code++;
1080 DEBUG(1, "%s: Undecryptable frame on Rx. Frame dropped.\n",
1083 stats->rx_crc_errors++;
1084 DEBUG(1, "%s: Bad CRC on Rx. Frame dropped.\n", dev->name);
1090 /* For now we ignore the 802.11 header completely, assuming
1091 that the card's firmware has handled anything vital */
1093 err = hermes_bap_pread(hw, IRQ_BAP, &hdr, sizeof(hdr),
1094 rxfid, HERMES_802_3_OFFSET);
1096 printk(KERN_ERR "%s: error %d reading frame header. "
1097 "Frame dropped.\n", dev->name, err);
1102 length = ntohs(hdr.len);
1105 if (length < 3) { /* No for even an 802.2 LLC header */
1106 /* At least on Symbol firmware with PCF we get quite a
1107 lot of these legitimately - Poll frames with no
1109 stats->rx_dropped++;
1112 if (length > IEEE802_11_DATA_LEN) {
1113 printk(KERN_WARNING "%s: Oversized frame received (%d bytes)\n",
1115 stats->rx_length_errors++;
1120 /* We need space for the packet data itself, plus an ethernet
1121 header, plus 2 bytes so we can align the IP header on a
1122 32bit boundary, plus 1 byte so we can read in odd length
1123 packets from the card, which has an IO granularity of 16
1125 skb = dev_alloc_skb(length+ETH_HLEN+2+1);
1127 printk(KERN_WARNING "%s: Can't allocate skb for Rx\n",
1132 skb_reserve(skb, 2); /* This way the IP header is aligned */
1134 /* Handle decapsulation
1135 * In most cases, the firmware tell us about SNAP frames.
1136 * For some reason, the SNAP frames sent by LinkSys APs
1137 * are not properly recognised by most firmwares.
1138 * So, check ourselves */
1139 if (((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_1042) ||
1140 ((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_TUNNEL) ||
1141 is_ethersnap(&hdr)) {
1142 /* These indicate a SNAP within 802.2 LLC within
1143 802.11 frame which we'll need to de-encapsulate to
1144 the original EthernetII frame. */
1146 if (length < ENCAPS_OVERHEAD) { /* No room for full LLC+SNAP */
1147 stats->rx_length_errors++;
1151 /* Remove SNAP header, reconstruct EthernetII frame */
1152 data_len = length - ENCAPS_OVERHEAD;
1153 data_off = HERMES_802_3_OFFSET + sizeof(hdr);
1155 eh = (struct ethhdr *)skb_put(skb, ETH_HLEN);
1157 memcpy(eh, &hdr, 2 * ETH_ALEN);
1158 eh->h_proto = hdr.ethertype;
1160 /* All other cases indicate a genuine 802.3 frame. No
1161 decapsulation needed. We just throw the whole
1162 thing in, and hope the protocol layer can deal with
1165 data_off = HERMES_802_3_OFFSET;
1166 /* FIXME: we re-read from the card data we already read here */
1169 p = skb_put(skb, data_len);
1170 err = hermes_bap_pread(hw, IRQ_BAP, p, ALIGN(data_len, 2),
1173 printk(KERN_ERR "%s: error %d reading frame. "
1174 "Frame dropped.\n", dev->name, err);
1179 dev->last_rx = jiffies;
1181 skb->protocol = eth_type_trans(skb, dev);
1182 skb->ip_summed = CHECKSUM_NONE;
1184 /* Process the wireless stats if needed */
1185 orinoco_stat_gather(dev, skb, &desc);
1187 /* Pass the packet to the networking stack */
1189 stats->rx_packets++;
1190 stats->rx_bytes += length;
1195 stats->rx_dropped++;
1198 dev_kfree_skb_irq(skb);
1202 /********************************************************************/
1203 /* Rx path (info frames) */
1204 /********************************************************************/
1206 static void print_linkstatus(struct net_device *dev, u16 status)
1210 if (suppress_linkstatus)
1214 case HERMES_LINKSTATUS_NOT_CONNECTED:
1215 s = "Not Connected";
1217 case HERMES_LINKSTATUS_CONNECTED:
1220 case HERMES_LINKSTATUS_DISCONNECTED:
1223 case HERMES_LINKSTATUS_AP_CHANGE:
1226 case HERMES_LINKSTATUS_AP_OUT_OF_RANGE:
1227 s = "AP Out of Range";
1229 case HERMES_LINKSTATUS_AP_IN_RANGE:
1232 case HERMES_LINKSTATUS_ASSOC_FAILED:
1233 s = "Association Failed";
1239 printk(KERN_INFO "%s: New link status: %s (%04x)\n",
1240 dev->name, s, status);
1243 static void __orinoco_ev_info(struct net_device *dev, hermes_t *hw)
1245 struct orinoco_private *priv = netdev_priv(dev);
1250 } __attribute__ ((packed)) info;
1254 /* This is an answer to an INQUIRE command that we did earlier,
1255 * or an information "event" generated by the card
1256 * The controller return to us a pseudo frame containing
1257 * the information in question - Jean II */
1258 infofid = hermes_read_regn(hw, INFOFID);
1260 /* Read the info frame header - don't try too hard */
1261 err = hermes_bap_pread(hw, IRQ_BAP, &info, sizeof(info),
1264 printk(KERN_ERR "%s: error %d reading info frame. "
1265 "Frame dropped.\n", dev->name, err);
1269 len = HERMES_RECLEN_TO_BYTES(le16_to_cpu(info.len));
1270 type = le16_to_cpu(info.type);
1273 case HERMES_INQ_TALLIES: {
1274 struct hermes_tallies_frame tallies;
1275 struct iw_statistics *wstats = &priv->wstats;
1277 if (len > sizeof(tallies)) {
1278 printk(KERN_WARNING "%s: Tallies frame too long (%d bytes)\n",
1280 len = sizeof(tallies);
1283 /* Read directly the data (no seek) */
1284 hermes_read_words(hw, HERMES_DATA1, (void *) &tallies,
1285 len / 2); /* FIXME: blech! */
1287 /* Increment our various counters */
1288 /* wstats->discard.nwid - no wrong BSSID stuff */
1289 wstats->discard.code +=
1290 le16_to_cpu(tallies.RxWEPUndecryptable);
1291 if (len == sizeof(tallies))
1292 wstats->discard.code +=
1293 le16_to_cpu(tallies.RxDiscards_WEPICVError) +
1294 le16_to_cpu(tallies.RxDiscards_WEPExcluded);
1295 wstats->discard.misc +=
1296 le16_to_cpu(tallies.TxDiscardsWrongSA);
1297 wstats->discard.fragment +=
1298 le16_to_cpu(tallies.RxMsgInBadMsgFragments);
1299 wstats->discard.retries +=
1300 le16_to_cpu(tallies.TxRetryLimitExceeded);
1301 /* wstats->miss.beacon - no match */
1304 case HERMES_INQ_LINKSTATUS: {
1305 struct hermes_linkstatus linkstatus;
1309 if (len != sizeof(linkstatus)) {
1310 printk(KERN_WARNING "%s: Unexpected size for linkstatus frame (%d bytes)\n",
1315 hermes_read_words(hw, HERMES_DATA1, (void *) &linkstatus,
1317 newstatus = le16_to_cpu(linkstatus.linkstatus);
1319 connected = (newstatus == HERMES_LINKSTATUS_CONNECTED)
1320 || (newstatus == HERMES_LINKSTATUS_AP_CHANGE)
1321 || (newstatus == HERMES_LINKSTATUS_AP_IN_RANGE);
1324 netif_carrier_on(dev);
1325 else if (!ignore_disconnect)
1326 netif_carrier_off(dev);
1328 if (newstatus != priv->last_linkstatus)
1329 print_linkstatus(dev, newstatus);
1331 priv->last_linkstatus = newstatus;
1335 printk(KERN_DEBUG "%s: Unknown information frame received: "
1336 "type 0x%04x, length %d\n", dev->name, type, len);
1337 /* We don't actually do anything about it */
1342 static void __orinoco_ev_infdrop(struct net_device *dev, hermes_t *hw)
1344 if (net_ratelimit())
1345 printk(KERN_DEBUG "%s: Information frame lost.\n", dev->name);
1348 /********************************************************************/
1349 /* Internal hardware control routines */
1350 /********************************************************************/
1352 int __orinoco_up(struct net_device *dev)
1354 struct orinoco_private *priv = netdev_priv(dev);
1355 struct hermes *hw = &priv->hw;
1358 err = __orinoco_program_rids(dev);
1360 printk(KERN_ERR "%s: Error %d configuring card\n",
1365 /* Fire things up again */
1366 hermes_set_irqmask(hw, ORINOCO_INTEN);
1367 err = hermes_enable_port(hw, 0);
1369 printk(KERN_ERR "%s: Error %d enabling MAC port\n",
1374 netif_start_queue(dev);
1379 int __orinoco_down(struct net_device *dev)
1381 struct orinoco_private *priv = netdev_priv(dev);
1382 struct hermes *hw = &priv->hw;
1385 netif_stop_queue(dev);
1387 if (! priv->hw_unavailable) {
1388 if (! priv->broken_disableport) {
1389 err = hermes_disable_port(hw, 0);
1391 /* Some firmwares (e.g. Intersil 1.3.x) seem
1392 * to have problems disabling the port, oh
1394 printk(KERN_WARNING "%s: Error %d disabling MAC port\n",
1396 priv->broken_disableport = 1;
1399 hermes_set_irqmask(hw, 0);
1400 hermes_write_regn(hw, EVACK, 0xffff);
1403 /* firmware will have to reassociate */
1404 netif_carrier_off(dev);
1405 priv->last_linkstatus = 0xffff;
1410 int orinoco_reinit_firmware(struct net_device *dev)
1412 struct orinoco_private *priv = netdev_priv(dev);
1413 struct hermes *hw = &priv->hw;
1416 err = hermes_init(hw);
1420 err = hermes_allocate(hw, priv->nicbuf_size, &priv->txfid);
1421 if (err == -EIO && priv->nicbuf_size > TX_NICBUF_SIZE_BUG) {
1422 /* Try workaround for old Symbol firmware bug */
1423 printk(KERN_WARNING "%s: firmware ALLOC bug detected "
1424 "(old Symbol firmware?). Trying to work around... ",
1427 priv->nicbuf_size = TX_NICBUF_SIZE_BUG;
1428 err = hermes_allocate(hw, priv->nicbuf_size, &priv->txfid);
1430 printk("failed!\n");
1438 static int __orinoco_hw_set_bitrate(struct orinoco_private *priv)
1440 hermes_t *hw = &priv->hw;
1443 if (priv->bitratemode >= BITRATE_TABLE_SIZE) {
1444 printk(KERN_ERR "%s: BUG: Invalid bitrate mode %d\n",
1445 priv->ndev->name, priv->bitratemode);
1449 switch (priv->firmware_type) {
1450 case FIRMWARE_TYPE_AGERE:
1451 err = hermes_write_wordrec(hw, USER_BAP,
1452 HERMES_RID_CNFTXRATECONTROL,
1453 bitrate_table[priv->bitratemode].agere_txratectrl);
1455 case FIRMWARE_TYPE_INTERSIL:
1456 case FIRMWARE_TYPE_SYMBOL:
1457 err = hermes_write_wordrec(hw, USER_BAP,
1458 HERMES_RID_CNFTXRATECONTROL,
1459 bitrate_table[priv->bitratemode].intersil_txratectrl);
1468 /* Change the WEP keys and/or the current keys. Can be called
1469 * either from __orinoco_hw_setup_wep() or directly from
1470 * orinoco_ioctl_setiwencode(). In the later case the association
1471 * with the AP is not broken (if the firmware can handle it),
1472 * which is needed for 802.1x implementations. */
1473 static int __orinoco_hw_setup_wepkeys(struct orinoco_private *priv)
1475 hermes_t *hw = &priv->hw;
1478 switch (priv->firmware_type) {
1479 case FIRMWARE_TYPE_AGERE:
1480 err = HERMES_WRITE_RECORD(hw, USER_BAP,
1481 HERMES_RID_CNFWEPKEYS_AGERE,
1485 err = hermes_write_wordrec(hw, USER_BAP,
1486 HERMES_RID_CNFTXKEY_AGERE,
1491 case FIRMWARE_TYPE_INTERSIL:
1492 case FIRMWARE_TYPE_SYMBOL:
1497 /* Force uniform key length to work around firmware bugs */
1498 keylen = le16_to_cpu(priv->keys[priv->tx_key].len);
1500 if (keylen > LARGE_KEY_SIZE) {
1501 printk(KERN_ERR "%s: BUG: Key %d has oversize length %d.\n",
1502 priv->ndev->name, priv->tx_key, keylen);
1506 /* Write all 4 keys */
1507 for(i = 0; i < ORINOCO_MAX_KEYS; i++) {
1508 err = hermes_write_ltv(hw, USER_BAP,
1509 HERMES_RID_CNFDEFAULTKEY0 + i,
1510 HERMES_BYTES_TO_RECLEN(keylen),
1511 priv->keys[i].data);
1516 /* Write the index of the key used in transmission */
1517 err = hermes_write_wordrec(hw, USER_BAP,
1518 HERMES_RID_CNFWEPDEFAULTKEYID,
1529 static int __orinoco_hw_setup_wep(struct orinoco_private *priv)
1531 hermes_t *hw = &priv->hw;
1533 int master_wep_flag;
1537 __orinoco_hw_setup_wepkeys(priv);
1539 if (priv->wep_restrict)
1540 auth_flag = HERMES_AUTH_SHARED_KEY;
1542 auth_flag = HERMES_AUTH_OPEN;
1544 switch (priv->firmware_type) {
1545 case FIRMWARE_TYPE_AGERE: /* Agere style WEP */
1547 /* Enable the shared-key authentication. */
1548 err = hermes_write_wordrec(hw, USER_BAP,
1549 HERMES_RID_CNFAUTHENTICATION_AGERE,
1552 err = hermes_write_wordrec(hw, USER_BAP,
1553 HERMES_RID_CNFWEPENABLED_AGERE,
1559 case FIRMWARE_TYPE_INTERSIL: /* Intersil style WEP */
1560 case FIRMWARE_TYPE_SYMBOL: /* Symbol style WEP */
1562 if (priv->wep_restrict ||
1563 (priv->firmware_type == FIRMWARE_TYPE_SYMBOL))
1564 master_wep_flag = HERMES_WEP_PRIVACY_INVOKED |
1565 HERMES_WEP_EXCL_UNENCRYPTED;
1567 master_wep_flag = HERMES_WEP_PRIVACY_INVOKED;
1569 err = hermes_write_wordrec(hw, USER_BAP,
1570 HERMES_RID_CNFAUTHENTICATION,
1575 master_wep_flag = 0;
1577 if (priv->iw_mode == IW_MODE_MONITOR)
1578 master_wep_flag |= HERMES_WEP_HOST_DECRYPT;
1580 /* Master WEP setting : on/off */
1581 err = hermes_write_wordrec(hw, USER_BAP,
1582 HERMES_RID_CNFWEPFLAGS_INTERSIL,
1593 static int __orinoco_program_rids(struct net_device *dev)
1595 struct orinoco_private *priv = netdev_priv(dev);
1596 hermes_t *hw = &priv->hw;
1598 struct hermes_idstring idbuf;
1600 /* Set the MAC address */
1601 err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFOWNMACADDR,
1602 HERMES_BYTES_TO_RECLEN(ETH_ALEN), dev->dev_addr);
1604 printk(KERN_ERR "%s: Error %d setting MAC address\n",
1609 /* Set up the link mode */
1610 err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFPORTTYPE,
1613 printk(KERN_ERR "%s: Error %d setting port type\n",
1617 /* Set the channel/frequency */
1618 if (priv->channel != 0 && priv->iw_mode != IW_MODE_INFRA) {
1619 err = hermes_write_wordrec(hw, USER_BAP,
1620 HERMES_RID_CNFOWNCHANNEL,
1623 printk(KERN_ERR "%s: Error %d setting channel %d\n",
1624 dev->name, err, priv->channel);
1629 if (priv->has_ibss) {
1632 if ((strlen(priv->desired_essid) == 0) && (priv->createibss)) {
1633 printk(KERN_WARNING "%s: This firmware requires an "
1634 "ESSID in IBSS-Ad-Hoc mode.\n", dev->name);
1635 /* With wvlan_cs, in this case, we would crash.
1636 * hopefully, this driver will behave better...
1640 createibss = priv->createibss;
1643 err = hermes_write_wordrec(hw, USER_BAP,
1644 HERMES_RID_CNFCREATEIBSS,
1647 printk(KERN_ERR "%s: Error %d setting CREATEIBSS\n",
1653 /* Set the desired ESSID */
1654 idbuf.len = cpu_to_le16(strlen(priv->desired_essid));
1655 memcpy(&idbuf.val, priv->desired_essid, sizeof(idbuf.val));
1656 /* WinXP wants partner to configure OWNSSID even in IBSS mode. (jimc) */
1657 err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFOWNSSID,
1658 HERMES_BYTES_TO_RECLEN(strlen(priv->desired_essid)+2),
1661 printk(KERN_ERR "%s: Error %d setting OWNSSID\n",
1665 err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFDESIREDSSID,
1666 HERMES_BYTES_TO_RECLEN(strlen(priv->desired_essid)+2),
1669 printk(KERN_ERR "%s: Error %d setting DESIREDSSID\n",
1674 /* Set the station name */
1675 idbuf.len = cpu_to_le16(strlen(priv->nick));
1676 memcpy(&idbuf.val, priv->nick, sizeof(idbuf.val));
1677 err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFOWNNAME,
1678 HERMES_BYTES_TO_RECLEN(strlen(priv->nick)+2),
1681 printk(KERN_ERR "%s: Error %d setting nickname\n",
1686 /* Set AP density */
1687 if (priv->has_sensitivity) {
1688 err = hermes_write_wordrec(hw, USER_BAP,
1689 HERMES_RID_CNFSYSTEMSCALE,
1692 printk(KERN_WARNING "%s: Error %d setting SYSTEMSCALE. "
1693 "Disabling sensitivity control\n",
1696 priv->has_sensitivity = 0;
1700 /* Set RTS threshold */
1701 err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFRTSTHRESHOLD,
1704 printk(KERN_ERR "%s: Error %d setting RTS threshold\n",
1709 /* Set fragmentation threshold or MWO robustness */
1711 err = hermes_write_wordrec(hw, USER_BAP,
1712 HERMES_RID_CNFMWOROBUST_AGERE,
1715 err = hermes_write_wordrec(hw, USER_BAP,
1716 HERMES_RID_CNFFRAGMENTATIONTHRESHOLD,
1719 printk(KERN_ERR "%s: Error %d setting fragmentation\n",
1725 err = __orinoco_hw_set_bitrate(priv);
1727 printk(KERN_ERR "%s: Error %d setting bitrate\n",
1732 /* Set power management */
1734 err = hermes_write_wordrec(hw, USER_BAP,
1735 HERMES_RID_CNFPMENABLED,
1738 printk(KERN_ERR "%s: Error %d setting up PM\n",
1743 err = hermes_write_wordrec(hw, USER_BAP,
1744 HERMES_RID_CNFMULTICASTRECEIVE,
1747 printk(KERN_ERR "%s: Error %d setting up PM\n",
1751 err = hermes_write_wordrec(hw, USER_BAP,
1752 HERMES_RID_CNFMAXSLEEPDURATION,
1755 printk(KERN_ERR "%s: Error %d setting up PM\n",
1759 err = hermes_write_wordrec(hw, USER_BAP,
1760 HERMES_RID_CNFPMHOLDOVERDURATION,
1763 printk(KERN_ERR "%s: Error %d setting up PM\n",
1769 /* Set preamble - only for Symbol so far... */
1770 if (priv->has_preamble) {
1771 err = hermes_write_wordrec(hw, USER_BAP,
1772 HERMES_RID_CNFPREAMBLE_SYMBOL,
1775 printk(KERN_ERR "%s: Error %d setting preamble\n",
1781 /* Set up encryption */
1782 if (priv->has_wep) {
1783 err = __orinoco_hw_setup_wep(priv);
1785 printk(KERN_ERR "%s: Error %d activating WEP\n",
1791 /* Set promiscuity / multicast*/
1792 priv->promiscuous = 0;
1794 __orinoco_set_multicast_list(dev); /* FIXME: what about the xmit_lock */
1799 /* FIXME: return int? */
1801 __orinoco_set_multicast_list(struct net_device *dev)
1803 struct orinoco_private *priv = netdev_priv(dev);
1804 hermes_t *hw = &priv->hw;
1806 int promisc, mc_count;
1808 /* The Hermes doesn't seem to have an allmulti mode, so we go
1809 * into promiscuous mode and let the upper levels deal. */
1810 if ( (dev->flags & IFF_PROMISC) || (dev->flags & IFF_ALLMULTI) ||
1811 (dev->mc_count > MAX_MULTICAST(priv)) ) {
1816 mc_count = dev->mc_count;
1819 if (promisc != priv->promiscuous) {
1820 err = hermes_write_wordrec(hw, USER_BAP,
1821 HERMES_RID_CNFPROMISCUOUSMODE,
1824 printk(KERN_ERR "%s: Error %d setting PROMISCUOUSMODE to 1.\n",
1827 priv->promiscuous = promisc;
1830 if (! promisc && (mc_count || priv->mc_count) ) {
1831 struct dev_mc_list *p = dev->mc_list;
1832 struct hermes_multicast mclist;
1835 for (i = 0; i < mc_count; i++) {
1836 /* paranoia: is list shorter than mc_count? */
1838 /* paranoia: bad address size in list? */
1839 BUG_ON(p->dmi_addrlen != ETH_ALEN);
1841 memcpy(mclist.addr[i], p->dmi_addr, ETH_ALEN);
1846 printk(KERN_WARNING "%s: Multicast list is "
1847 "longer than mc_count\n", dev->name);
1849 err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFGROUPADDRESSES,
1850 HERMES_BYTES_TO_RECLEN(priv->mc_count * ETH_ALEN),
1853 printk(KERN_ERR "%s: Error %d setting multicast list.\n",
1856 priv->mc_count = mc_count;
1859 /* Since we can set the promiscuous flag when it wasn't asked
1860 for, make sure the net_device knows about it. */
1861 if (priv->promiscuous)
1862 dev->flags |= IFF_PROMISC;
1864 dev->flags &= ~IFF_PROMISC;
1867 static int orinoco_reconfigure(struct net_device *dev)
1869 struct orinoco_private *priv = netdev_priv(dev);
1870 struct hermes *hw = &priv->hw;
1871 unsigned long flags;
1874 if (priv->broken_disableport) {
1875 schedule_work(&priv->reset_work);
1879 if (orinoco_lock(priv, &flags) != 0)
1882 err = hermes_disable_port(hw, 0);
1884 printk(KERN_WARNING "%s: Unable to disable port while reconfiguring card\n",
1886 priv->broken_disableport = 1;
1890 err = __orinoco_program_rids(dev);
1892 printk(KERN_WARNING "%s: Unable to reconfigure card\n",
1897 err = hermes_enable_port(hw, 0);
1899 printk(KERN_WARNING "%s: Unable to enable port while reconfiguring card\n",
1906 printk(KERN_WARNING "%s: Resetting instead...\n", dev->name);
1907 schedule_work(&priv->reset_work);
1911 orinoco_unlock(priv, &flags);
1916 /* This must be called from user context, without locks held - use
1917 * schedule_work() */
1918 static void orinoco_reset(struct net_device *dev)
1920 struct orinoco_private *priv = netdev_priv(dev);
1921 struct hermes *hw = &priv->hw;
1923 unsigned long flags;
1925 if (orinoco_lock(priv, &flags) != 0)
1926 /* When the hardware becomes available again, whatever
1927 * detects that is responsible for re-initializing
1928 * it. So no need for anything further */
1931 netif_stop_queue(dev);
1933 /* Shut off interrupts. Depending on what state the hardware
1934 * is in, this might not work, but we'll try anyway */
1935 hermes_set_irqmask(hw, 0);
1936 hermes_write_regn(hw, EVACK, 0xffff);
1938 priv->hw_unavailable++;
1939 priv->last_linkstatus = 0xffff; /* firmware will have to reassociate */
1940 netif_carrier_off(dev);
1942 orinoco_unlock(priv, &flags);
1944 if (priv->hard_reset)
1945 err = (*priv->hard_reset)(priv);
1947 printk(KERN_ERR "%s: orinoco_reset: Error %d "
1948 "performing hard reset\n", dev->name, err);
1949 /* FIXME: shutdown of some sort */
1953 err = orinoco_reinit_firmware(dev);
1955 printk(KERN_ERR "%s: orinoco_reset: Error %d re-initializing firmware\n",
1960 spin_lock_irq(&priv->lock); /* This has to be called from user context */
1962 priv->hw_unavailable--;
1964 /* priv->open or priv->hw_unavailable might have changed while
1965 * we dropped the lock */
1966 if (priv->open && (! priv->hw_unavailable)) {
1967 err = __orinoco_up(dev);
1969 printk(KERN_ERR "%s: orinoco_reset: Error %d reenabling card\n",
1972 dev->trans_start = jiffies;
1975 spin_unlock_irq(&priv->lock);
1980 /********************************************************************/
1981 /* Interrupt handler */
1982 /********************************************************************/
1984 static void __orinoco_ev_tick(struct net_device *dev, hermes_t *hw)
1986 printk(KERN_DEBUG "%s: TICK\n", dev->name);
1989 static void __orinoco_ev_wterr(struct net_device *dev, hermes_t *hw)
1991 /* This seems to happen a fair bit under load, but ignoring it
1992 seems to work fine...*/
1993 printk(KERN_DEBUG "%s: MAC controller error (WTERR). Ignoring.\n",
1997 irqreturn_t orinoco_interrupt(int irq, void *dev_id, struct pt_regs *regs)
1999 struct net_device *dev = (struct net_device *)dev_id;
2000 struct orinoco_private *priv = netdev_priv(dev);
2001 hermes_t *hw = &priv->hw;
2002 int count = MAX_IRQLOOPS_PER_IRQ;
2004 /* These are used to detect a runaway interrupt situation */
2005 /* If we get more than MAX_IRQLOOPS_PER_JIFFY iterations in a jiffy,
2006 * we panic and shut down the hardware */
2007 static int last_irq_jiffy = 0; /* jiffies value the last time
2009 static int loops_this_jiffy = 0;
2010 unsigned long flags;
2012 if (orinoco_lock(priv, &flags) != 0) {
2013 /* If hw is unavailable - we don't know if the irq was
2018 evstat = hermes_read_regn(hw, EVSTAT);
2019 events = evstat & hw->inten;
2021 orinoco_unlock(priv, &flags);
2025 if (jiffies != last_irq_jiffy)
2026 loops_this_jiffy = 0;
2027 last_irq_jiffy = jiffies;
2029 while (events && count--) {
2030 if (++loops_this_jiffy > MAX_IRQLOOPS_PER_JIFFY) {
2031 printk(KERN_WARNING "%s: IRQ handler is looping too "
2032 "much! Resetting.\n", dev->name);
2033 /* Disable interrupts for now */
2034 hermes_set_irqmask(hw, 0);
2035 schedule_work(&priv->reset_work);
2039 /* Check the card hasn't been removed */
2040 if (! hermes_present(hw)) {
2041 DEBUG(0, "orinoco_interrupt(): card removed\n");
2045 if (events & HERMES_EV_TICK)
2046 __orinoco_ev_tick(dev, hw);
2047 if (events & HERMES_EV_WTERR)
2048 __orinoco_ev_wterr(dev, hw);
2049 if (events & HERMES_EV_INFDROP)
2050 __orinoco_ev_infdrop(dev, hw);
2051 if (events & HERMES_EV_INFO)
2052 __orinoco_ev_info(dev, hw);
2053 if (events & HERMES_EV_RX)
2054 __orinoco_ev_rx(dev, hw);
2055 if (events & HERMES_EV_TXEXC)
2056 __orinoco_ev_txexc(dev, hw);
2057 if (events & HERMES_EV_TX)
2058 __orinoco_ev_tx(dev, hw);
2059 if (events & HERMES_EV_ALLOC)
2060 __orinoco_ev_alloc(dev, hw);
2062 hermes_write_regn(hw, EVACK, events);
2064 evstat = hermes_read_regn(hw, EVSTAT);
2065 events = evstat & hw->inten;
2068 orinoco_unlock(priv, &flags);
2072 /********************************************************************/
2073 /* Initialization */
2074 /********************************************************************/
2077 u16 id, variant, major, minor;
2078 } __attribute__ ((packed));
2080 static inline fwtype_t determine_firmware_type(struct comp_id *nic_id)
2082 if (nic_id->id < 0x8000)
2083 return FIRMWARE_TYPE_AGERE;
2084 else if (nic_id->id == 0x8000 && nic_id->major == 0)
2085 return FIRMWARE_TYPE_SYMBOL;
2087 return FIRMWARE_TYPE_INTERSIL;
2090 /* Set priv->firmware type, determine firmware properties */
2091 static int determine_firmware(struct net_device *dev)
2093 struct orinoco_private *priv = netdev_priv(dev);
2094 hermes_t *hw = &priv->hw;
2096 struct comp_id nic_id, sta_id;
2097 unsigned int firmver;
2098 char tmp[SYMBOL_MAX_VER_LEN+1];
2100 /* Get the hardware version */
2101 err = HERMES_READ_RECORD(hw, USER_BAP, HERMES_RID_NICID, &nic_id);
2103 printk(KERN_ERR "%s: Cannot read hardware identity: error %d\n",
2108 le16_to_cpus(&nic_id.id);
2109 le16_to_cpus(&nic_id.variant);
2110 le16_to_cpus(&nic_id.major);
2111 le16_to_cpus(&nic_id.minor);
2112 printk(KERN_DEBUG "%s: Hardware identity %04x:%04x:%04x:%04x\n",
2113 dev->name, nic_id.id, nic_id.variant,
2114 nic_id.major, nic_id.minor);
2116 priv->firmware_type = determine_firmware_type(&nic_id);
2118 /* Get the firmware version */
2119 err = HERMES_READ_RECORD(hw, USER_BAP, HERMES_RID_STAID, &sta_id);
2121 printk(KERN_ERR "%s: Cannot read station identity: error %d\n",
2126 le16_to_cpus(&sta_id.id);
2127 le16_to_cpus(&sta_id.variant);
2128 le16_to_cpus(&sta_id.major);
2129 le16_to_cpus(&sta_id.minor);
2130 printk(KERN_DEBUG "%s: Station identity %04x:%04x:%04x:%04x\n",
2131 dev->name, sta_id.id, sta_id.variant,
2132 sta_id.major, sta_id.minor);
2134 switch (sta_id.id) {
2136 printk(KERN_ERR "%s: Primary firmware is active\n",
2140 printk(KERN_ERR "%s: Tertiary firmware is active\n",
2143 case 0x1f: /* Intersil, Agere, Symbol Spectrum24 */
2144 case 0x21: /* Symbol Spectrum24 Trilogy */
2147 printk(KERN_NOTICE "%s: Unknown station ID, please report\n",
2152 /* Default capabilities */
2153 priv->has_sensitivity = 1;
2155 priv->has_preamble = 0;
2156 priv->has_port3 = 1;
2159 priv->has_big_wep = 0;
2161 /* Determine capabilities from the firmware version */
2162 switch (priv->firmware_type) {
2163 case FIRMWARE_TYPE_AGERE:
2164 /* Lucent Wavelan IEEE, Lucent Orinoco, Cabletron RoamAbout,
2165 ELSA, Melco, HP, IBM, Dell 1150, Compaq 110/210 */
2166 snprintf(priv->fw_name, sizeof(priv->fw_name) - 1,
2167 "Lucent/Agere %d.%02d", sta_id.major, sta_id.minor);
2169 firmver = ((unsigned long)sta_id.major << 16) | sta_id.minor;
2171 priv->has_ibss = (firmver >= 0x60006);
2172 priv->has_wep = (firmver >= 0x40020);
2173 priv->has_big_wep = 1; /* FIXME: this is wrong - how do we tell
2174 Gold cards from the others? */
2175 priv->has_mwo = (firmver >= 0x60000);
2176 priv->has_pm = (firmver >= 0x40020); /* Don't work in 7.52 ? */
2177 priv->ibss_port = 1;
2179 /* Tested with Agere firmware :
2180 * 1.16 ; 4.08 ; 4.52 ; 6.04 ; 6.16 ; 7.28 => Jean II
2181 * Tested CableTron firmware : 4.32 => Anton */
2183 case FIRMWARE_TYPE_SYMBOL:
2184 /* Symbol , 3Com AirConnect, Intel, Ericsson WLAN */
2185 /* Intel MAC : 00:02:B3:* */
2186 /* 3Com MAC : 00:50:DA:* */
2187 memset(tmp, 0, sizeof(tmp));
2188 /* Get the Symbol firmware version */
2189 err = hermes_read_ltv(hw, USER_BAP,
2190 HERMES_RID_SECONDARYVERSION_SYMBOL,
2191 SYMBOL_MAX_VER_LEN, NULL, &tmp);
2194 "%s: Error %d reading Symbol firmware info. Wildly guessing capabilities...\n",
2199 /* The firmware revision is a string, the format is
2200 * something like : "V2.20-01".
2201 * Quick and dirty parsing... - Jean II
2203 firmver = ((tmp[1] - '0') << 16) | ((tmp[3] - '0') << 12)
2204 | ((tmp[4] - '0') << 8) | ((tmp[6] - '0') << 4)
2207 tmp[SYMBOL_MAX_VER_LEN] = '\0';
2210 snprintf(priv->fw_name, sizeof(priv->fw_name) - 1,
2213 priv->has_ibss = (firmver >= 0x20000);
2214 priv->has_wep = (firmver >= 0x15012);
2215 priv->has_big_wep = (firmver >= 0x20000);
2216 priv->has_pm = (firmver >= 0x20000 && firmver < 0x22000) ||
2217 (firmver >= 0x29000 && firmver < 0x30000) ||
2219 priv->has_preamble = (firmver >= 0x20000);
2220 priv->ibss_port = 4;
2221 /* Tested with Intel firmware : 0x20015 => Jean II */
2222 /* Tested with 3Com firmware : 0x15012 & 0x22001 => Jean II */
2224 case FIRMWARE_TYPE_INTERSIL:
2225 /* D-Link, Linksys, Adtron, ZoomAir, and many others...
2226 * Samsung, Compaq 100/200 and Proxim are slightly
2227 * different and less well tested */
2228 /* D-Link MAC : 00:40:05:* */
2229 /* Addtron MAC : 00:90:D1:* */
2230 snprintf(priv->fw_name, sizeof(priv->fw_name) - 1,
2231 "Intersil %d.%d.%d", sta_id.major, sta_id.minor,
2234 firmver = ((unsigned long)sta_id.major << 16) |
2235 ((unsigned long)sta_id.minor << 8) | sta_id.variant;
2237 priv->has_ibss = (firmver >= 0x000700); /* FIXME */
2238 priv->has_big_wep = priv->has_wep = (firmver >= 0x000800);
2239 priv->has_pm = (firmver >= 0x000700);
2241 if (firmver >= 0x000800)
2242 priv->ibss_port = 0;
2244 printk(KERN_NOTICE "%s: Intersil firmware earlier "
2245 "than v0.8.x - several features not supported\n",
2247 priv->ibss_port = 1;
2251 printk(KERN_DEBUG "%s: Firmware determined as %s\n", dev->name,
2257 static int orinoco_init(struct net_device *dev)
2259 struct orinoco_private *priv = netdev_priv(dev);
2260 hermes_t *hw = &priv->hw;
2262 struct hermes_idstring nickbuf;
2266 TRACE_ENTER(dev->name);
2268 /* No need to lock, the hw_unavailable flag is already set in
2269 * alloc_orinocodev() */
2270 priv->nicbuf_size = IEEE802_11_FRAME_LEN + ETH_HLEN;
2272 /* Initialize the firmware */
2273 err = orinoco_reinit_firmware(dev);
2275 printk(KERN_ERR "%s: failed to initialize firmware (err = %d)\n",
2280 err = determine_firmware(dev);
2282 printk(KERN_ERR "%s: Incompatible firmware, aborting\n",
2287 if (priv->has_port3)
2288 printk(KERN_DEBUG "%s: Ad-hoc demo mode supported\n", dev->name);
2290 printk(KERN_DEBUG "%s: IEEE standard IBSS ad-hoc mode supported\n",
2292 if (priv->has_wep) {
2293 printk(KERN_DEBUG "%s: WEP supported, ", dev->name);
2294 if (priv->has_big_wep)
2295 printk("104-bit key\n");
2297 printk("40-bit key\n");
2300 /* Get the MAC address */
2301 err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CNFOWNMACADDR,
2302 ETH_ALEN, NULL, dev->dev_addr);
2304 printk(KERN_WARNING "%s: failed to read MAC address!\n",
2309 printk(KERN_DEBUG "%s: MAC address %02X:%02X:%02X:%02X:%02X:%02X\n",
2310 dev->name, dev->dev_addr[0], dev->dev_addr[1],
2311 dev->dev_addr[2], dev->dev_addr[3], dev->dev_addr[4],
2314 /* Get the station name */
2315 err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CNFOWNNAME,
2316 sizeof(nickbuf), &reclen, &nickbuf);
2318 printk(KERN_ERR "%s: failed to read station name\n",
2323 len = min(IW_ESSID_MAX_SIZE, (int)le16_to_cpu(nickbuf.len));
2325 len = min(IW_ESSID_MAX_SIZE, 2 * reclen);
2326 memcpy(priv->nick, &nickbuf.val, len);
2327 priv->nick[len] = '\0';
2329 printk(KERN_DEBUG "%s: Station name \"%s\"\n", dev->name, priv->nick);
2331 /* Get allowed channels */
2332 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CHANNELLIST,
2333 &priv->channel_mask);
2335 printk(KERN_ERR "%s: failed to read channel list!\n",
2340 /* Get initial AP density */
2341 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFSYSTEMSCALE,
2343 if (err || priv->ap_density < 1 || priv->ap_density > 3) {
2344 priv->has_sensitivity = 0;
2347 /* Get initial RTS threshold */
2348 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFRTSTHRESHOLD,
2351 printk(KERN_ERR "%s: failed to read RTS threshold!\n",
2356 /* Get initial fragmentation settings */
2358 err = hermes_read_wordrec(hw, USER_BAP,
2359 HERMES_RID_CNFMWOROBUST_AGERE,
2362 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFFRAGMENTATIONTHRESHOLD,
2363 &priv->frag_thresh);
2365 printk(KERN_ERR "%s: failed to read fragmentation settings!\n",
2370 /* Power management setup */
2374 err = hermes_read_wordrec(hw, USER_BAP,
2375 HERMES_RID_CNFMAXSLEEPDURATION,
2378 printk(KERN_ERR "%s: failed to read power management period!\n",
2382 err = hermes_read_wordrec(hw, USER_BAP,
2383 HERMES_RID_CNFPMHOLDOVERDURATION,
2386 printk(KERN_ERR "%s: failed to read power management timeout!\n",
2392 /* Preamble setup */
2393 if (priv->has_preamble) {
2394 err = hermes_read_wordrec(hw, USER_BAP,
2395 HERMES_RID_CNFPREAMBLE_SYMBOL,
2401 /* Set up the default configuration */
2402 priv->iw_mode = IW_MODE_INFRA;
2403 /* By default use IEEE/IBSS ad-hoc mode if we have it */
2404 priv->prefer_port3 = priv->has_port3 && (! priv->has_ibss);
2405 set_port_type(priv);
2406 priv->channel = 0; /* use firmware default */
2408 priv->promiscuous = 0;
2412 /* Make the hardware available, as long as it hasn't been
2413 * removed elsewhere (e.g. by PCMCIA hot unplug) */
2414 spin_lock_irq(&priv->lock);
2415 priv->hw_unavailable--;
2416 spin_unlock_irq(&priv->lock);
2418 printk(KERN_DEBUG "%s: ready\n", dev->name);
2421 TRACE_EXIT(dev->name);
2425 struct net_device *alloc_orinocodev(int sizeof_card,
2426 int (*hard_reset)(struct orinoco_private *))
2428 struct net_device *dev;
2429 struct orinoco_private *priv;
2431 dev = alloc_etherdev(sizeof(struct orinoco_private) + sizeof_card);
2434 priv = netdev_priv(dev);
2437 priv->card = (void *)((unsigned long)netdev_priv(dev)
2438 + sizeof(struct orinoco_private));
2442 /* Setup / override net_device fields */
2443 dev->init = orinoco_init;
2444 dev->hard_start_xmit = orinoco_xmit;
2445 dev->tx_timeout = orinoco_tx_timeout;
2446 dev->watchdog_timeo = HZ; /* 1 second timeout */
2447 dev->get_stats = orinoco_get_stats;
2448 dev->get_wireless_stats = orinoco_get_wireless_stats;
2449 dev->do_ioctl = orinoco_ioctl;
2450 dev->change_mtu = orinoco_change_mtu;
2451 dev->set_multicast_list = orinoco_set_multicast_list;
2452 /* we use the default eth_mac_addr for setting the MAC addr */
2454 /* Set up default callbacks */
2455 dev->open = orinoco_open;
2456 dev->stop = orinoco_stop;
2457 priv->hard_reset = hard_reset;
2459 spin_lock_init(&priv->lock);
2461 priv->hw_unavailable = 1; /* orinoco_init() must clear this
2462 * before anything else touches the
2464 INIT_WORK(&priv->reset_work, (void (*)(void *))orinoco_reset, dev);
2466 netif_carrier_off(dev);
2467 priv->last_linkstatus = 0xffff;
2473 void free_orinocodev(struct net_device *dev)
2478 /********************************************************************/
2479 /* Wireless extensions */
2480 /********************************************************************/
2482 static int orinoco_hw_get_bssid(struct orinoco_private *priv,
2485 hermes_t *hw = &priv->hw;
2487 unsigned long flags;
2489 if (orinoco_lock(priv, &flags) != 0)
2492 err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CURRENTBSSID,
2493 ETH_ALEN, NULL, buf);
2495 orinoco_unlock(priv, &flags);
2500 static int orinoco_hw_get_essid(struct orinoco_private *priv, int *active,
2501 char buf[IW_ESSID_MAX_SIZE+1])
2503 hermes_t *hw = &priv->hw;
2505 struct hermes_idstring essidbuf;
2506 char *p = (char *)(&essidbuf.val);
2508 unsigned long flags;
2510 if (orinoco_lock(priv, &flags) != 0)
2513 if (strlen(priv->desired_essid) > 0) {
2514 /* We read the desired SSID from the hardware rather
2515 than from priv->desired_essid, just in case the
2516 firmware is allowed to change it on us. I'm not
2518 /* My guess is that the OWNSSID should always be whatever
2519 * we set to the card, whereas CURRENT_SSID is the one that
2520 * may change... - Jean II */
2525 rid = (priv->port_type == 3) ? HERMES_RID_CNFOWNSSID :
2526 HERMES_RID_CNFDESIREDSSID;
2528 err = hermes_read_ltv(hw, USER_BAP, rid, sizeof(essidbuf),
2535 err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CURRENTSSID,
2536 sizeof(essidbuf), NULL, &essidbuf);
2541 len = le16_to_cpu(essidbuf.len);
2543 memset(buf, 0, IW_ESSID_MAX_SIZE+1);
2544 memcpy(buf, p, len);
2548 orinoco_unlock(priv, &flags);
2553 static long orinoco_hw_get_freq(struct orinoco_private *priv)
2556 hermes_t *hw = &priv->hw;
2560 unsigned long flags;
2562 if (orinoco_lock(priv, &flags) != 0)
2565 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CURRENTCHANNEL, &channel);
2569 /* Intersil firmware 1.3.5 returns 0 when the interface is down */
2575 if ( (channel < 1) || (channel > NUM_CHANNELS) ) {
2576 printk(KERN_WARNING "%s: Channel out of range (%d)!\n",
2577 priv->ndev->name, channel);
2582 freq = channel_frequency[channel-1] * 100000;
2585 orinoco_unlock(priv, &flags);
2589 return err ? err : freq;
2592 static int orinoco_hw_get_bitratelist(struct orinoco_private *priv,
2593 int *numrates, s32 *rates, int max)
2595 hermes_t *hw = &priv->hw;
2596 struct hermes_idstring list;
2597 unsigned char *p = (unsigned char *)&list.val;
2601 unsigned long flags;
2603 if (orinoco_lock(priv, &flags) != 0)
2606 err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_SUPPORTEDDATARATES,
2607 sizeof(list), NULL, &list);
2608 orinoco_unlock(priv, &flags);
2613 num = le16_to_cpu(list.len);
2615 num = min(num, max);
2617 for (i = 0; i < num; i++) {
2618 rates[i] = (p[i] & 0x7f) * 500000; /* convert to bps */
2624 static int orinoco_ioctl_getiwrange(struct net_device *dev, struct iw_point *rrq)
2626 struct orinoco_private *priv = netdev_priv(dev);
2629 struct iw_range range;
2632 unsigned long flags;
2634 TRACE_ENTER(dev->name);
2636 if (!access_ok(VERIFY_WRITE, rrq->pointer, sizeof(range)))
2639 rrq->length = sizeof(range);
2641 if (orinoco_lock(priv, &flags) != 0)
2644 mode = priv->iw_mode;
2645 orinoco_unlock(priv, &flags);
2647 memset(&range, 0, sizeof(range));
2649 /* Much of this shamelessly taken from wvlan_cs.c. No idea
2650 * what it all means -dgibson */
2651 range.we_version_compiled = WIRELESS_EXT;
2652 range.we_version_source = 11;
2654 range.min_nwid = range.max_nwid = 0; /* We don't use nwids */
2656 /* Set available channels/frequencies */
2657 range.num_channels = NUM_CHANNELS;
2659 for (i = 0; i < NUM_CHANNELS; i++) {
2660 if (priv->channel_mask & (1 << i)) {
2661 range.freq[k].i = i + 1;
2662 range.freq[k].m = channel_frequency[i] * 100000;
2663 range.freq[k].e = 1;
2667 if (k >= IW_MAX_FREQUENCIES)
2670 range.num_frequency = k;
2672 range.sensitivity = 3;
2674 if ((mode == IW_MODE_ADHOC) && (priv->spy_number == 0)){
2675 /* Quality stats meaningless in ad-hoc mode */
2676 range.max_qual.qual = 0;
2677 range.max_qual.level = 0;
2678 range.max_qual.noise = 0;
2679 range.avg_qual.qual = 0;
2680 range.avg_qual.level = 0;
2681 range.avg_qual.noise = 0;
2683 range.max_qual.qual = 0x8b - 0x2f;
2684 range.max_qual.level = 0x2f - 0x95 - 1;
2685 range.max_qual.noise = 0x2f - 0x95 - 1;
2686 /* Need to get better values */
2687 range.avg_qual.qual = 0x24;
2688 range.avg_qual.level = 0xC2;
2689 range.avg_qual.noise = 0x9E;
2692 err = orinoco_hw_get_bitratelist(priv, &numrates,
2693 range.bitrate, IW_MAX_BITRATES);
2696 range.num_bitrates = numrates;
2698 /* Set an indication of the max TCP throughput in bit/s that we can
2699 * expect using this interface. May be use for QoS stuff...
2702 range.throughput = 5 * 1000 * 1000; /* ~5 Mb/s */
2704 range.throughput = 1.5 * 1000 * 1000; /* ~1.5 Mb/s */
2707 range.max_rts = 2347;
2708 range.min_frag = 256;
2709 range.max_frag = 2346;
2711 if (orinoco_lock(priv, &flags) != 0)
2713 if (priv->has_wep) {
2714 range.max_encoding_tokens = ORINOCO_MAX_KEYS;
2716 range.encoding_size[0] = SMALL_KEY_SIZE;
2717 range.num_encoding_sizes = 1;
2719 if (priv->has_big_wep) {
2720 range.encoding_size[1] = LARGE_KEY_SIZE;
2721 range.num_encoding_sizes = 2;
2724 range.num_encoding_sizes = 0;
2725 range.max_encoding_tokens = 0;
2727 orinoco_unlock(priv, &flags);
2730 range.max_pmp = 65535000;
2732 range.max_pmt = 65535 * 1000; /* ??? */
2733 range.pmp_flags = IW_POWER_PERIOD;
2734 range.pmt_flags = IW_POWER_TIMEOUT;
2735 range.pm_capa = IW_POWER_PERIOD | IW_POWER_TIMEOUT | IW_POWER_UNICAST_R;
2737 range.num_txpower = 1;
2738 range.txpower[0] = 15; /* 15dBm */
2739 range.txpower_capa = IW_TXPOW_DBM;
2741 range.retry_capa = IW_RETRY_LIMIT | IW_RETRY_LIFETIME;
2742 range.retry_flags = IW_RETRY_LIMIT;
2743 range.r_time_flags = IW_RETRY_LIFETIME;
2744 range.min_retry = 0;
2745 range.max_retry = 65535; /* ??? */
2746 range.min_r_time = 0;
2747 range.max_r_time = 65535 * 1000; /* ??? */
2749 if (copy_to_user(rrq->pointer, &range, sizeof(range)))
2752 TRACE_EXIT(dev->name);
2757 static int orinoco_ioctl_setiwencode(struct net_device *dev, struct iw_point *erq)
2759 struct orinoco_private *priv = netdev_priv(dev);
2760 int index = (erq->flags & IW_ENCODE_INDEX) - 1;
2761 int setindex = priv->tx_key;
2762 int enable = priv->wep_on;
2763 int restricted = priv->wep_restrict;
2766 char keybuf[ORINOCO_MAX_KEY_SIZE];
2767 unsigned long flags;
2769 if (! priv->has_wep)
2773 /* We actually have a key to set - check its length */
2774 if (erq->length > LARGE_KEY_SIZE)
2777 if ( (erq->length > SMALL_KEY_SIZE) && !priv->has_big_wep )
2780 if (copy_from_user(keybuf, erq->pointer, erq->length))
2784 if (orinoco_lock(priv, &flags) != 0)
2788 if ((index < 0) || (index >= ORINOCO_MAX_KEYS))
2789 index = priv->tx_key;
2791 /* Adjust key length to a supported value */
2792 if (erq->length > SMALL_KEY_SIZE) {
2793 xlen = LARGE_KEY_SIZE;
2794 } else if (erq->length > 0) {
2795 xlen = SMALL_KEY_SIZE;
2799 /* Switch on WEP if off */
2800 if ((!enable) && (xlen > 0)) {
2805 /* Important note : if the user do "iwconfig eth0 enc off",
2806 * we will arrive there with an index of -1. This is valid
2807 * but need to be taken care off... Jean II */
2808 if ((index < 0) || (index >= ORINOCO_MAX_KEYS)) {
2809 if((index != -1) || (erq->flags == 0)) {
2814 /* Set the index : Check that the key is valid */
2815 if(priv->keys[index].len == 0) {
2823 if (erq->flags & IW_ENCODE_DISABLED)
2825 if (erq->flags & IW_ENCODE_OPEN)
2827 if (erq->flags & IW_ENCODE_RESTRICTED)
2831 priv->keys[index].len = cpu_to_le16(xlen);
2832 memset(priv->keys[index].data, 0,
2833 sizeof(priv->keys[index].data));
2834 memcpy(priv->keys[index].data, keybuf, erq->length);
2836 priv->tx_key = setindex;
2838 /* Try fast key change if connected and only keys are changed */
2839 if (priv->wep_on && enable && (priv->wep_restrict == restricted) &&
2840 netif_carrier_ok(dev)) {
2841 err = __orinoco_hw_setup_wepkeys(priv);
2842 /* No need to commit if successful */
2846 priv->wep_on = enable;
2847 priv->wep_restrict = restricted;
2850 orinoco_unlock(priv, &flags);
2855 static int orinoco_ioctl_getiwencode(struct net_device *dev, struct iw_point *erq)
2857 struct orinoco_private *priv = netdev_priv(dev);
2858 int index = (erq->flags & IW_ENCODE_INDEX) - 1;
2860 char keybuf[ORINOCO_MAX_KEY_SIZE];
2861 unsigned long flags;
2863 if (! priv->has_wep)
2866 if (orinoco_lock(priv, &flags) != 0)
2869 if ((index < 0) || (index >= ORINOCO_MAX_KEYS))
2870 index = priv->tx_key;
2874 erq->flags |= IW_ENCODE_DISABLED;
2875 erq->flags |= index + 1;
2877 if (priv->wep_restrict)
2878 erq->flags |= IW_ENCODE_RESTRICTED;
2880 erq->flags |= IW_ENCODE_OPEN;
2882 xlen = le16_to_cpu(priv->keys[index].len);
2886 memcpy(keybuf, priv->keys[index].data, ORINOCO_MAX_KEY_SIZE);
2888 orinoco_unlock(priv, &flags);
2891 if (copy_to_user(erq->pointer, keybuf, xlen))
2898 static int orinoco_ioctl_setessid(struct net_device *dev, struct iw_point *erq)
2900 struct orinoco_private *priv = netdev_priv(dev);
2901 char essidbuf[IW_ESSID_MAX_SIZE+1];
2902 unsigned long flags;
2904 /* Note : ESSID is ignored in Ad-Hoc demo mode, but we can set it
2905 * anyway... - Jean II */
2907 memset(&essidbuf, 0, sizeof(essidbuf));
2910 /* iwconfig includes the NUL in the specified length */
2911 if (erq->length > IW_ESSID_MAX_SIZE+1)
2914 if (copy_from_user(&essidbuf, erq->pointer, erq->length))
2917 essidbuf[IW_ESSID_MAX_SIZE] = '\0';
2920 if (orinoco_lock(priv, &flags) != 0)
2923 memcpy(priv->desired_essid, essidbuf, sizeof(priv->desired_essid));
2925 orinoco_unlock(priv, &flags);
2930 static int orinoco_ioctl_getessid(struct net_device *dev, struct iw_point *erq)
2932 struct orinoco_private *priv = netdev_priv(dev);
2933 char essidbuf[IW_ESSID_MAX_SIZE+1];
2936 unsigned long flags;
2938 TRACE_ENTER(dev->name);
2940 if (netif_running(dev)) {
2941 err = orinoco_hw_get_essid(priv, &active, essidbuf);
2945 if (orinoco_lock(priv, &flags) != 0)
2947 memcpy(essidbuf, priv->desired_essid, sizeof(essidbuf));
2948 orinoco_unlock(priv, &flags);
2952 erq->length = strlen(essidbuf) + 1;
2954 if (copy_to_user(erq->pointer, essidbuf, erq->length))
2957 TRACE_EXIT(dev->name);
2962 static int orinoco_ioctl_setnick(struct net_device *dev, struct iw_point *nrq)
2964 struct orinoco_private *priv = netdev_priv(dev);
2965 char nickbuf[IW_ESSID_MAX_SIZE+1];
2966 unsigned long flags;
2968 if (nrq->length > IW_ESSID_MAX_SIZE)
2971 memset(nickbuf, 0, sizeof(nickbuf));
2973 if (copy_from_user(nickbuf, nrq->pointer, nrq->length))
2976 nickbuf[nrq->length] = '\0';
2978 if (orinoco_lock(priv, &flags) != 0)
2981 memcpy(priv->nick, nickbuf, sizeof(priv->nick));
2983 orinoco_unlock(priv, &flags);
2988 static int orinoco_ioctl_getnick(struct net_device *dev, struct iw_point *nrq)
2990 struct orinoco_private *priv = netdev_priv(dev);
2991 char nickbuf[IW_ESSID_MAX_SIZE+1];
2992 unsigned long flags;
2994 if (orinoco_lock(priv, &flags) != 0)
2997 memcpy(nickbuf, priv->nick, IW_ESSID_MAX_SIZE+1);
2998 orinoco_unlock(priv, &flags);
3000 nrq->length = strlen(nickbuf)+1;
3002 if (copy_to_user(nrq->pointer, nickbuf, sizeof(nickbuf)))
3008 static int orinoco_ioctl_setfreq(struct net_device *dev, struct iw_freq *frq)
3010 struct orinoco_private *priv = netdev_priv(dev);
3012 unsigned long flags;
3014 /* We can only use this in Ad-Hoc demo mode to set the operating
3015 * frequency, or in IBSS mode to set the frequency where the IBSS
3016 * will be created - Jean II */
3017 if (priv->iw_mode != IW_MODE_ADHOC)
3020 if ( (frq->e == 0) && (frq->m <= 1000) ) {
3021 /* Setting by channel number */
3024 /* Setting by frequency - search the table */
3028 for (i = 0; i < (6 - frq->e); i++)
3031 for (i = 0; i < NUM_CHANNELS; i++)
3032 if (frq->m == (channel_frequency[i] * mult))
3036 if ( (chan < 1) || (chan > NUM_CHANNELS) ||
3037 ! (priv->channel_mask & (1 << (chan-1)) ) )
3040 if (orinoco_lock(priv, &flags) != 0)
3042 priv->channel = chan;
3043 orinoco_unlock(priv, &flags);
3048 static int orinoco_ioctl_getsens(struct net_device *dev, struct iw_param *srq)
3050 struct orinoco_private *priv = netdev_priv(dev);
3051 hermes_t *hw = &priv->hw;
3054 unsigned long flags;
3056 if (!priv->has_sensitivity)
3059 if (orinoco_lock(priv, &flags) != 0)
3061 err = hermes_read_wordrec(hw, USER_BAP,
3062 HERMES_RID_CNFSYSTEMSCALE, &val);
3063 orinoco_unlock(priv, &flags);
3069 srq->fixed = 0; /* auto */
3074 static int orinoco_ioctl_setsens(struct net_device *dev, struct iw_param *srq)
3076 struct orinoco_private *priv = netdev_priv(dev);
3077 int val = srq->value;
3078 unsigned long flags;
3080 if (!priv->has_sensitivity)
3083 if ((val < 1) || (val > 3))
3086 if (orinoco_lock(priv, &flags) != 0)
3088 priv->ap_density = val;
3089 orinoco_unlock(priv, &flags);
3094 static int orinoco_ioctl_setrts(struct net_device *dev, struct iw_param *rrq)
3096 struct orinoco_private *priv = netdev_priv(dev);
3097 int val = rrq->value;
3098 unsigned long flags;
3103 if ( (val < 0) || (val > 2347) )
3106 if (orinoco_lock(priv, &flags) != 0)
3109 priv->rts_thresh = val;
3110 orinoco_unlock(priv, &flags);
3115 static int orinoco_ioctl_setfrag(struct net_device *dev, struct iw_param *frq)
3117 struct orinoco_private *priv = netdev_priv(dev);
3119 unsigned long flags;
3121 if (orinoco_lock(priv, &flags) != 0)
3124 if (priv->has_mwo) {
3126 priv->mwo_robust = 0;
3129 printk(KERN_WARNING "%s: Fixed fragmentation is "
3130 "not supported on this firmware. "
3131 "Using MWO robust instead.\n", dev->name);
3132 priv->mwo_robust = 1;
3136 priv->frag_thresh = 2346;
3138 if ( (frq->value < 256) || (frq->value > 2346) )
3141 priv->frag_thresh = frq->value & ~0x1; /* must be even */
3145 orinoco_unlock(priv, &flags);
3150 static int orinoco_ioctl_getfrag(struct net_device *dev, struct iw_param *frq)
3152 struct orinoco_private *priv = netdev_priv(dev);
3153 hermes_t *hw = &priv->hw;
3156 unsigned long flags;
3158 if (orinoco_lock(priv, &flags) != 0)
3161 if (priv->has_mwo) {
3162 err = hermes_read_wordrec(hw, USER_BAP,
3163 HERMES_RID_CNFMWOROBUST_AGERE,
3168 frq->value = val ? 2347 : 0;
3169 frq->disabled = ! val;
3172 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFFRAGMENTATIONTHRESHOLD,
3178 frq->disabled = (val >= 2346);
3182 orinoco_unlock(priv, &flags);
3187 static int orinoco_ioctl_setrate(struct net_device *dev, struct iw_param *rrq)
3189 struct orinoco_private *priv = netdev_priv(dev);
3192 int bitrate; /* 100s of kilobits */
3194 unsigned long flags;
3196 /* As the user space doesn't know our highest rate, it uses -1
3197 * to ask us to set the highest rate. Test it using "iwconfig
3198 * ethX rate auto" - Jean II */
3199 if (rrq->value == -1)
3202 if (rrq->value % 100000)
3204 bitrate = rrq->value / 100000;
3207 if ( (bitrate != 10) && (bitrate != 20) &&
3208 (bitrate != 55) && (bitrate != 110) )
3211 for (i = 0; i < BITRATE_TABLE_SIZE; i++)
3212 if ( (bitrate_table[i].bitrate == bitrate) &&
3213 (bitrate_table[i].automatic == ! rrq->fixed) ) {
3221 if (orinoco_lock(priv, &flags) != 0)
3223 priv->bitratemode = ratemode;
3224 orinoco_unlock(priv, &flags);
3229 static int orinoco_ioctl_getrate(struct net_device *dev, struct iw_param *rrq)
3231 struct orinoco_private *priv = netdev_priv(dev);
3232 hermes_t *hw = &priv->hw;
3237 unsigned long flags;
3239 if (orinoco_lock(priv, &flags) != 0)
3242 ratemode = priv->bitratemode;
3244 BUG_ON((ratemode < 0) || (ratemode >= BITRATE_TABLE_SIZE));
3246 rrq->value = bitrate_table[ratemode].bitrate * 100000;
3247 rrq->fixed = ! bitrate_table[ratemode].automatic;
3250 /* If the interface is running we try to find more about the
3252 if (netif_running(dev)) {
3253 err = hermes_read_wordrec(hw, USER_BAP,
3254 HERMES_RID_CURRENTTXRATE, &val);
3258 switch (priv->firmware_type) {
3259 case FIRMWARE_TYPE_AGERE: /* Lucent style rate */
3260 /* Note : in Lucent firmware, the return value of
3261 * HERMES_RID_CURRENTTXRATE is the bitrate in Mb/s,
3262 * and therefore is totally different from the
3263 * encoding of HERMES_RID_CNFTXRATECONTROL.
3264 * Don't forget that 6Mb/s is really 5.5Mb/s */
3266 rrq->value = 5500000;
3268 rrq->value = val * 1000000;
3270 case FIRMWARE_TYPE_INTERSIL: /* Intersil style rate */
3271 case FIRMWARE_TYPE_SYMBOL: /* Symbol style rate */
3272 for (i = 0; i < BITRATE_TABLE_SIZE; i++)
3273 if (bitrate_table[i].intersil_txratectrl == val) {
3277 if (i >= BITRATE_TABLE_SIZE)
3278 printk(KERN_INFO "%s: Unable to determine current bitrate (0x%04hx)\n",
3281 rrq->value = bitrate_table[ratemode].bitrate * 100000;
3289 orinoco_unlock(priv, &flags);
3294 static int orinoco_ioctl_setpower(struct net_device *dev, struct iw_param *prq)
3296 struct orinoco_private *priv = netdev_priv(dev);
3298 unsigned long flags;
3300 if (orinoco_lock(priv, &flags) != 0)
3303 if (prq->disabled) {
3306 switch (prq->flags & IW_POWER_MODE) {
3307 case IW_POWER_UNICAST_R:
3311 case IW_POWER_ALL_R:
3316 /* No flags : but we may have a value - Jean II */
3324 if (prq->flags & IW_POWER_TIMEOUT) {
3326 priv->pm_timeout = prq->value / 1000;
3328 if (prq->flags & IW_POWER_PERIOD) {
3330 priv->pm_period = prq->value / 1000;
3332 /* It's valid to not have a value if we are just toggling
3333 * the flags... Jean II */
3341 orinoco_unlock(priv, &flags);
3346 static int orinoco_ioctl_getpower(struct net_device *dev, struct iw_param *prq)
3348 struct orinoco_private *priv = netdev_priv(dev);
3349 hermes_t *hw = &priv->hw;
3351 u16 enable, period, timeout, mcast;
3352 unsigned long flags;
3354 if (orinoco_lock(priv, &flags) != 0)
3357 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFPMENABLED, &enable);
3361 err = hermes_read_wordrec(hw, USER_BAP,
3362 HERMES_RID_CNFMAXSLEEPDURATION, &period);
3366 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFPMHOLDOVERDURATION, &timeout);
3370 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFMULTICASTRECEIVE, &mcast);
3374 prq->disabled = !enable;
3375 /* Note : by default, display the period */
3376 if ((prq->flags & IW_POWER_TYPE) == IW_POWER_TIMEOUT) {
3377 prq->flags = IW_POWER_TIMEOUT;
3378 prq->value = timeout * 1000;
3380 prq->flags = IW_POWER_PERIOD;
3381 prq->value = period * 1000;
3384 prq->flags |= IW_POWER_ALL_R;
3386 prq->flags |= IW_POWER_UNICAST_R;
3389 orinoco_unlock(priv, &flags);
3394 static int orinoco_ioctl_getretry(struct net_device *dev, struct iw_param *rrq)
3396 struct orinoco_private *priv = netdev_priv(dev);
3397 hermes_t *hw = &priv->hw;
3399 u16 short_limit, long_limit, lifetime;
3400 unsigned long flags;
3402 if (orinoco_lock(priv, &flags) != 0)
3405 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_SHORTRETRYLIMIT,
3410 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_LONGRETRYLIMIT,
3415 err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_MAXTRANSMITLIFETIME,
3420 rrq->disabled = 0; /* Can't be disabled */
3422 /* Note : by default, display the retry number */
3423 if ((rrq->flags & IW_RETRY_TYPE) == IW_RETRY_LIFETIME) {
3424 rrq->flags = IW_RETRY_LIFETIME;
3425 rrq->value = lifetime * 1000; /* ??? */
3427 /* By default, display the min number */
3428 if ((rrq->flags & IW_RETRY_MAX)) {
3429 rrq->flags = IW_RETRY_LIMIT | IW_RETRY_MAX;
3430 rrq->value = long_limit;
3432 rrq->flags = IW_RETRY_LIMIT;
3433 rrq->value = short_limit;
3434 if(short_limit != long_limit)
3435 rrq->flags |= IW_RETRY_MIN;
3440 orinoco_unlock(priv, &flags);
3445 static int orinoco_ioctl_setibssport(struct net_device *dev, struct iwreq *wrq)
3447 struct orinoco_private *priv = netdev_priv(dev);
3448 int val = *( (int *) wrq->u.name );
3449 unsigned long flags;
3451 if (orinoco_lock(priv, &flags) != 0)
3454 priv->ibss_port = val ;
3456 /* Actually update the mode we are using */
3457 set_port_type(priv);
3459 orinoco_unlock(priv, &flags);
3463 static int orinoco_ioctl_getibssport(struct net_device *dev, struct iwreq *wrq)
3465 struct orinoco_private *priv = netdev_priv(dev);
3466 int *val = (int *)wrq->u.name;
3467 unsigned long flags;
3469 if (orinoco_lock(priv, &flags) != 0)
3472 *val = priv->ibss_port;
3473 orinoco_unlock(priv, &flags);
3478 static int orinoco_ioctl_setport3(struct net_device *dev, struct iwreq *wrq)
3480 struct orinoco_private *priv = netdev_priv(dev);
3481 int val = *( (int *) wrq->u.name );
3483 unsigned long flags;
3485 if (orinoco_lock(priv, &flags) != 0)
3489 case 0: /* Try to do IEEE ad-hoc mode */
3490 if (! priv->has_ibss) {
3494 priv->prefer_port3 = 0;
3498 case 1: /* Try to do Lucent proprietary ad-hoc mode */
3499 if (! priv->has_port3) {
3503 priv->prefer_port3 = 1;
3511 /* Actually update the mode we are using */
3512 set_port_type(priv);
3514 orinoco_unlock(priv, &flags);
3519 static int orinoco_ioctl_getport3(struct net_device *dev, struct iwreq *wrq)
3521 struct orinoco_private *priv = netdev_priv(dev);
3522 int *val = (int *)wrq->u.name;
3523 unsigned long flags;
3525 if (orinoco_lock(priv, &flags) != 0)
3528 *val = priv->prefer_port3;
3529 orinoco_unlock(priv, &flags);
3533 /* Spy is used for link quality/strength measurements in Ad-Hoc mode
3535 static int orinoco_ioctl_setspy(struct net_device *dev, struct iw_point *srq)
3537 struct orinoco_private *priv = netdev_priv(dev);
3538 struct sockaddr address[IW_MAX_SPY];
3539 int number = srq->length;
3542 unsigned long flags;
3544 /* Check the number of addresses */
3545 if (number > IW_MAX_SPY)
3548 /* Get the data in the driver */
3550 if (copy_from_user(address, srq->pointer,
3551 sizeof(struct sockaddr) * number))
3555 /* Make sure nobody mess with the structure while we do */
3556 if (orinoco_lock(priv, &flags) != 0)
3559 /* orinoco_lock() doesn't disable interrupts, so make sure the
3560 * interrupt rx path don't get confused while we copy */
3561 priv->spy_number = 0;
3564 /* Extract the addresses */
3565 for (i = 0; i < number; i++)
3566 memcpy(priv->spy_address[i], address[i].sa_data,
3569 memset(priv->spy_stat, 0,
3570 sizeof(struct iw_quality) * IW_MAX_SPY);
3571 /* Set number of addresses */
3572 priv->spy_number = number;
3575 /* Now, let the others play */
3576 orinoco_unlock(priv, &flags);
3581 static int orinoco_ioctl_getspy(struct net_device *dev, struct iw_point *srq)
3583 struct orinoco_private *priv = netdev_priv(dev);
3584 struct sockaddr address[IW_MAX_SPY];
3585 struct iw_quality spy_stat[IW_MAX_SPY];
3588 unsigned long flags;
3590 if (orinoco_lock(priv, &flags) != 0)
3593 number = priv->spy_number;
3594 if ((number > 0) && (srq->pointer)) {
3595 /* Create address struct */
3596 for (i = 0; i < number; i++) {
3597 memcpy(address[i].sa_data, priv->spy_address[i],
3599 address[i].sa_family = AF_UNIX;
3602 /* In theory, we should disable irqs while copying the stats
3603 * because the rx path might update it in the middle...
3604 * Bah, who care ? - Jean II */
3605 memcpy(&spy_stat, priv->spy_stat,
3606 sizeof(struct iw_quality) * IW_MAX_SPY);
3607 for (i=0; i < number; i++)
3608 priv->spy_stat[i].updated = 0;
3611 orinoco_unlock(priv, &flags);
3613 /* Push stuff to user space */
3614 srq->length = number;
3615 if(copy_to_user(srq->pointer, address,
3616 sizeof(struct sockaddr) * number))
3618 if(copy_to_user(srq->pointer + (sizeof(struct sockaddr)*number),
3619 &spy_stat, sizeof(struct iw_quality) * number))
3626 orinoco_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
3628 struct orinoco_private *priv = netdev_priv(dev);
3629 struct iwreq *wrq = (struct iwreq *)rq;
3633 unsigned long flags;
3635 TRACE_ENTER(dev->name);
3637 /* In theory, we could allow most of the the SET stuff to be
3638 * done. In practice, the lapse of time at startup when the
3639 * card is not ready is very short, so why bother... Note
3640 * that netif_device_present is different from up/down
3641 * (ifconfig), when the device is not yet up, it is usually
3642 * already ready... Jean II */
3643 if (! netif_device_present(dev))
3648 strcpy(wrq->u.name, "IEEE 802.11-DS");
3652 wrq->u.ap_addr.sa_family = ARPHRD_ETHER;
3653 err = orinoco_hw_get_bssid(priv, wrq->u.ap_addr.sa_data);
3657 err = orinoco_ioctl_getiwrange(dev, &wrq->u.data);
3661 if (orinoco_lock(priv, &flags) != 0)
3663 switch (wrq->u.mode) {
3665 if (! (priv->has_ibss || priv->has_port3) )
3668 priv->iw_mode = IW_MODE_ADHOC;
3674 priv->iw_mode = IW_MODE_INFRA;
3682 set_port_type(priv);
3683 orinoco_unlock(priv, &flags);
3687 if (orinoco_lock(priv, &flags) != 0)
3689 wrq->u.mode = priv->iw_mode;
3690 orinoco_unlock(priv, &flags);
3694 err = orinoco_ioctl_setiwencode(dev, &wrq->u.encoding);
3700 if (! capable(CAP_NET_ADMIN)) {
3705 err = orinoco_ioctl_getiwencode(dev, &wrq->u.encoding);
3709 err = orinoco_ioctl_setessid(dev, &wrq->u.essid);
3715 err = orinoco_ioctl_getessid(dev, &wrq->u.essid);
3719 err = orinoco_ioctl_setnick(dev, &wrq->u.data);
3725 err = orinoco_ioctl_getnick(dev, &wrq->u.data);
3729 tmp = orinoco_hw_get_freq(priv);
3733 wrq->u.freq.m = tmp;
3739 err = orinoco_ioctl_setfreq(dev, &wrq->u.freq);
3745 err = orinoco_ioctl_getsens(dev, &wrq->u.sens);
3749 err = orinoco_ioctl_setsens(dev, &wrq->u.sens);
3755 wrq->u.rts.value = priv->rts_thresh;
3756 wrq->u.rts.disabled = (wrq->u.rts.value == 2347);
3757 wrq->u.rts.fixed = 1;
3761 err = orinoco_ioctl_setrts(dev, &wrq->u.rts);
3767 err = orinoco_ioctl_setfrag(dev, &wrq->u.frag);
3773 err = orinoco_ioctl_getfrag(dev, &wrq->u.frag);
3777 err = orinoco_ioctl_setrate(dev, &wrq->u.bitrate);
3783 err = orinoco_ioctl_getrate(dev, &wrq->u.bitrate);
3787 err = orinoco_ioctl_setpower(dev, &wrq->u.power);
3793 err = orinoco_ioctl_getpower(dev, &wrq->u.power);
3797 /* The card only supports one tx power, so this is easy */
3798 wrq->u.txpower.value = 15; /* dBm */
3799 wrq->u.txpower.fixed = 1;
3800 wrq->u.txpower.disabled = 0;
3801 wrq->u.txpower.flags = IW_TXPOW_DBM;
3809 err = orinoco_ioctl_getretry(dev, &wrq->u.retry);
3813 err = orinoco_ioctl_setspy(dev, &wrq->u.data);
3817 err = orinoco_ioctl_getspy(dev, &wrq->u.data);
3821 if (wrq->u.data.pointer) {
3822 struct iw_priv_args privtab[] = {
3823 { SIOCIWFIRSTPRIV + 0x0, 0, 0, "force_reset" },
3824 { SIOCIWFIRSTPRIV + 0x1, 0, 0, "card_reset" },
3825 { SIOCIWFIRSTPRIV + 0x2,
3826 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
3828 { SIOCIWFIRSTPRIV + 0x3, 0,
3829 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
3831 { SIOCIWFIRSTPRIV + 0x4,
3832 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
3833 0, "set_preamble" },
3834 { SIOCIWFIRSTPRIV + 0x5, 0,
3835 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
3837 { SIOCIWFIRSTPRIV + 0x6,
3838 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
3839 0, "set_ibssport" },
3840 { SIOCIWFIRSTPRIV + 0x7, 0,
3841 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
3845 wrq->u.data.length = sizeof(privtab) / sizeof(privtab[0]);
3846 if (copy_to_user(wrq->u.data.pointer, privtab, sizeof(privtab)))
3851 case SIOCIWFIRSTPRIV + 0x0: /* force_reset */
3852 case SIOCIWFIRSTPRIV + 0x1: /* card_reset */
3853 if (! capable(CAP_NET_ADMIN)) {
3858 printk(KERN_DEBUG "%s: Force scheduling reset!\n", dev->name);
3860 schedule_work(&priv->reset_work);
3863 case SIOCIWFIRSTPRIV + 0x2: /* set_port3 */
3864 if (! capable(CAP_NET_ADMIN)) {
3869 err = orinoco_ioctl_setport3(dev, wrq);
3874 case SIOCIWFIRSTPRIV + 0x3: /* get_port3 */
3875 err = orinoco_ioctl_getport3(dev, wrq);
3878 case SIOCIWFIRSTPRIV + 0x4: /* set_preamble */
3879 if (! capable(CAP_NET_ADMIN)) {
3884 /* 802.11b has recently defined some short preamble.
3885 * Basically, the Phy header has been reduced in size.
3886 * This increase performance, especially at high rates
3887 * (the preamble is transmitted at 1Mb/s), unfortunately
3888 * this give compatibility troubles... - Jean II */
3889 if(priv->has_preamble) {
3890 int val = *( (int *) wrq->u.name );
3892 if (orinoco_lock(priv, &flags) != 0)
3898 orinoco_unlock(priv, &flags);
3904 case SIOCIWFIRSTPRIV + 0x5: /* get_preamble */
3905 if(priv->has_preamble) {
3906 int *val = (int *)wrq->u.name;
3908 if (orinoco_lock(priv, &flags) != 0)
3910 *val = priv->preamble;
3911 orinoco_unlock(priv, &flags);
3915 case SIOCIWFIRSTPRIV + 0x6: /* set_ibssport */
3916 if (! capable(CAP_NET_ADMIN)) {
3921 err = orinoco_ioctl_setibssport(dev, wrq);
3926 case SIOCIWFIRSTPRIV + 0x7: /* get_ibssport */
3927 err = orinoco_ioctl_getibssport(dev, wrq);
3934 if (! err && changed && netif_running(dev)) {
3935 err = orinoco_reconfigure(dev);
3938 TRACE_EXIT(dev->name);
3944 /********************************************************************/
3946 /********************************************************************/
3949 static void show_rx_frame(struct orinoco_rxframe_hdr *frame)
3951 printk(KERN_DEBUG "RX descriptor:\n");
3952 printk(KERN_DEBUG " status = 0x%04x\n", frame->desc.status);
3953 printk(KERN_DEBUG " time = 0x%08x\n", frame->desc.time);
3954 printk(KERN_DEBUG " silence = 0x%02x\n", frame->desc.silence);
3955 printk(KERN_DEBUG " signal = 0x%02x\n", frame->desc.signal);
3956 printk(KERN_DEBUG " rate = 0x%02x\n", frame->desc.rate);
3957 printk(KERN_DEBUG " rxflow = 0x%02x\n", frame->desc.rxflow);
3958 printk(KERN_DEBUG " reserved = 0x%08x\n", frame->desc.reserved);
3960 printk(KERN_DEBUG "IEEE 802.11 header:\n");
3961 printk(KERN_DEBUG " frame_ctl = 0x%04x\n",
3962 frame->p80211.frame_ctl);
3963 printk(KERN_DEBUG " duration_id = 0x%04x\n",
3964 frame->p80211.duration_id);
3965 printk(KERN_DEBUG " addr1 = %02x:%02x:%02x:%02x:%02x:%02x\n",
3966 frame->p80211.addr1[0], frame->p80211.addr1[1],
3967 frame->p80211.addr1[2], frame->p80211.addr1[3],
3968 frame->p80211.addr1[4], frame->p80211.addr1[5]);
3969 printk(KERN_DEBUG " addr2 = %02x:%02x:%02x:%02x:%02x:%02x\n",
3970 frame->p80211.addr2[0], frame->p80211.addr2[1],
3971 frame->p80211.addr2[2], frame->p80211.addr2[3],
3972 frame->p80211.addr2[4], frame->p80211.addr2[5]);
3973 printk(KERN_DEBUG " addr3 = %02x:%02x:%02x:%02x:%02x:%02x\n",
3974 frame->p80211.addr3[0], frame->p80211.addr3[1],
3975 frame->p80211.addr3[2], frame->p80211.addr3[3],
3976 frame->p80211.addr3[4], frame->p80211.addr3[5]);
3977 printk(KERN_DEBUG " seq_ctl = 0x%04x\n",
3978 frame->p80211.seq_ctl);
3979 printk(KERN_DEBUG " addr4 = %02x:%02x:%02x:%02x:%02x:%02x\n",
3980 frame->p80211.addr4[0], frame->p80211.addr4[1],
3981 frame->p80211.addr4[2], frame->p80211.addr4[3],
3982 frame->p80211.addr4[4], frame->p80211.addr4[5]);
3983 printk(KERN_DEBUG " data_len = 0x%04x\n",
3984 frame->p80211.data_len);
3986 printk(KERN_DEBUG "IEEE 802.3 header:\n");
3987 printk(KERN_DEBUG " dest = %02x:%02x:%02x:%02x:%02x:%02x\n",
3988 frame->p8023.h_dest[0], frame->p8023.h_dest[1],
3989 frame->p8023.h_dest[2], frame->p8023.h_dest[3],
3990 frame->p8023.h_dest[4], frame->p8023.h_dest[5]);
3991 printk(KERN_DEBUG " src = %02x:%02x:%02x:%02x:%02x:%02x\n",
3992 frame->p8023.h_source[0], frame->p8023.h_source[1],
3993 frame->p8023.h_source[2], frame->p8023.h_source[3],
3994 frame->p8023.h_source[4], frame->p8023.h_source[5]);
3995 printk(KERN_DEBUG " len = 0x%04x\n", frame->p8023.h_proto);
3997 printk(KERN_DEBUG "IEEE 802.2 LLC/SNAP header:\n");
3998 printk(KERN_DEBUG " DSAP = 0x%02x\n", frame->p8022.dsap);
3999 printk(KERN_DEBUG " SSAP = 0x%02x\n", frame->p8022.ssap);
4000 printk(KERN_DEBUG " ctrl = 0x%02x\n", frame->p8022.ctrl);
4001 printk(KERN_DEBUG " OUI = %02x:%02x:%02x\n",
4002 frame->p8022.oui[0], frame->p8022.oui[1], frame->p8022.oui[2]);
4003 printk(KERN_DEBUG " ethertype = 0x%04x\n", frame->ethertype);
4007 /********************************************************************/
4008 /* Module initialization */
4009 /********************************************************************/
4011 EXPORT_SYMBOL(alloc_orinocodev);
4012 EXPORT_SYMBOL(free_orinocodev);
4014 EXPORT_SYMBOL(__orinoco_up);
4015 EXPORT_SYMBOL(__orinoco_down);
4016 EXPORT_SYMBOL(orinoco_stop);
4017 EXPORT_SYMBOL(orinoco_reinit_firmware);
4019 EXPORT_SYMBOL(orinoco_interrupt);
4021 /* Can't be declared "const" or the whole __initdata section will
4023 static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION
4024 " (David Gibson <hermes@gibson.dropbear.id.au>, "
4025 "Pavel Roskin <proski@gnu.org>, et al)";
4027 static int __init init_orinoco(void)
4029 printk(KERN_DEBUG "%s\n", version);
4033 static void __exit exit_orinoco(void)
4037 module_init(init_orinoco);
4038 module_exit(exit_orinoco);