1 /************************************************************************
2 * s2io.c: A Linux PCI-X Ethernet driver for Neterion 10GbE Server NIC
3 * Copyright(c) 2002-2007 Neterion Inc.
5 * This software may be used and distributed according to the terms of
6 * the GNU General Public License (GPL), incorporated herein by reference.
7 * Drivers based on or derived from this code fall under the GPL and must
8 * retain the authorship, copyright and license notice. This file is not
9 * a complete program and may only be used when the entire operating
10 * system is licensed under the GPL.
11 * See the file COPYING in this distribution for more information.
14 * Jeff Garzik : For pointing out the improper error condition
15 * check in the s2io_xmit routine and also some
16 * issues in the Tx watch dog function. Also for
17 * patiently answering all those innumerable
18 * questions regaring the 2.6 porting issues.
19 * Stephen Hemminger : Providing proper 2.6 porting mechanism for some
20 * macros available only in 2.6 Kernel.
21 * Francois Romieu : For pointing out all code part that were
22 * deprecated and also styling related comments.
23 * Grant Grundler : For helping me get rid of some Architecture
25 * Christopher Hellwig : Some more 2.6 specific issues in the driver.
27 * The module loadable parameters that are supported by the driver and a brief
28 * explaination of all the variables.
30 * rx_ring_num : This can be used to program the number of receive rings used
32 * rx_ring_sz: This defines the number of receive blocks each ring can have.
33 * This is also an array of size 8.
34 * rx_ring_mode: This defines the operation mode of all 8 rings. The valid
36 * tx_fifo_num: This defines the number of Tx FIFOs thats used int the driver.
37 * tx_fifo_len: This too is an array of 8. Each element defines the number of
38 * Tx descriptors that can be associated with each corresponding FIFO.
39 * intr_type: This defines the type of interrupt. The values can be 0(INTA),
40 * 2(MSI_X). Default value is '2(MSI_X)'
41 * lro_enable: Specifies whether to enable Large Receive Offload (LRO) or not.
42 * Possible values '1' for enable '0' for disable. Default is '0'
43 * lro_max_pkts: This parameter defines maximum number of packets can be
44 * aggregated as a single large packet
45 * napi: This parameter used to enable/disable NAPI (polling Rx)
46 * Possible values '1' for enable and '0' for disable. Default is '1'
47 * ufo: This parameter used to enable/disable UDP Fragmentation Offload(UFO)
48 * Possible values '1' for enable and '0' for disable. Default is '0'
49 * vlan_tag_strip: This can be used to enable or disable vlan stripping.
50 * Possible values '1' for enable , '0' for disable.
51 * Default is '2' - which means disable in promisc mode
52 * and enable in non-promiscuous mode.
53 * multiq: This parameter used to enable/disable MULTIQUEUE support.
54 * Possible values '1' for enable and '0' for disable. Default is '0'
55 ************************************************************************/
57 #include <linux/module.h>
58 #include <linux/types.h>
59 #include <linux/errno.h>
60 #include <linux/ioport.h>
61 #include <linux/pci.h>
62 #include <linux/dma-mapping.h>
63 #include <linux/kernel.h>
64 #include <linux/netdevice.h>
65 #include <linux/etherdevice.h>
66 #include <linux/skbuff.h>
67 #include <linux/init.h>
68 #include <linux/delay.h>
69 #include <linux/stddef.h>
70 #include <linux/ioctl.h>
71 #include <linux/timex.h>
72 #include <linux/ethtool.h>
73 #include <linux/workqueue.h>
74 #include <linux/if_vlan.h>
76 #include <linux/tcp.h>
79 #include <asm/system.h>
80 #include <asm/uaccess.h>
82 #include <asm/div64.h>
87 #include "s2io-regs.h"
89 #define DRV_VERSION "2.0.26.19"
91 /* S2io Driver name & version. */
92 static char s2io_driver_name[] = "Neterion";
93 static char s2io_driver_version[] = DRV_VERSION;
95 static int rxd_size[2] = {32,48};
96 static int rxd_count[2] = {127,85};
98 static inline int RXD_IS_UP2DT(struct RxD_t *rxdp)
102 ret = ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
103 (GET_RXD_MARKER(rxdp->Control_2) != THE_RXD_MARK));
109 * Cards with following subsystem_id have a link state indication
110 * problem, 600B, 600C, 600D, 640B, 640C and 640D.
111 * macro below identifies these cards given the subsystem_id.
113 #define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \
114 (dev_type == XFRAME_I_DEVICE) ? \
115 ((((subid >= 0x600B) && (subid <= 0x600D)) || \
116 ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0
118 #define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \
119 ADAPTER_STATUS_RMAC_LOCAL_FAULT)))
120 #define TASKLET_IN_USE test_and_set_bit(0, (&sp->tasklet_status))
123 static inline int rx_buffer_level(struct s2io_nic * sp, int rxb_size, int ring)
125 struct mac_info *mac_control;
127 mac_control = &sp->mac_control;
128 if (rxb_size <= rxd_count[sp->rxd_mode])
130 else if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16)
135 static inline int is_s2io_card_up(const struct s2io_nic * sp)
137 return test_bit(__S2IO_STATE_CARD_UP, &sp->state);
140 /* Ethtool related variables and Macros. */
141 static char s2io_gstrings[][ETH_GSTRING_LEN] = {
142 "Register test\t(offline)",
143 "Eeprom test\t(offline)",
144 "Link test\t(online)",
145 "RLDRAM test\t(offline)",
146 "BIST Test\t(offline)"
149 static char ethtool_xena_stats_keys[][ETH_GSTRING_LEN] = {
151 {"tmac_data_octets"},
155 {"tmac_pause_ctrl_frms"},
159 {"tmac_any_err_frms"},
160 {"tmac_ttl_less_fb_octets"},
161 {"tmac_vld_ip_octets"},
169 {"rmac_data_octets"},
170 {"rmac_fcs_err_frms"},
172 {"rmac_vld_mcst_frms"},
173 {"rmac_vld_bcst_frms"},
174 {"rmac_in_rng_len_err_frms"},
175 {"rmac_out_rng_len_err_frms"},
177 {"rmac_pause_ctrl_frms"},
178 {"rmac_unsup_ctrl_frms"},
180 {"rmac_accepted_ucst_frms"},
181 {"rmac_accepted_nucst_frms"},
182 {"rmac_discarded_frms"},
183 {"rmac_drop_events"},
184 {"rmac_ttl_less_fb_octets"},
186 {"rmac_usized_frms"},
187 {"rmac_osized_frms"},
189 {"rmac_jabber_frms"},
190 {"rmac_ttl_64_frms"},
191 {"rmac_ttl_65_127_frms"},
192 {"rmac_ttl_128_255_frms"},
193 {"rmac_ttl_256_511_frms"},
194 {"rmac_ttl_512_1023_frms"},
195 {"rmac_ttl_1024_1518_frms"},
203 {"rmac_err_drp_udp"},
204 {"rmac_xgmii_err_sym"},
222 {"rmac_xgmii_data_err_cnt"},
223 {"rmac_xgmii_ctrl_err_cnt"},
224 {"rmac_accepted_ip"},
228 {"new_rd_req_rtry_cnt"},
230 {"wr_rtry_rd_ack_cnt"},
233 {"new_wr_req_rtry_cnt"},
236 {"rd_rtry_wr_ack_cnt"},
246 static char ethtool_enhanced_stats_keys[][ETH_GSTRING_LEN] = {
247 {"rmac_ttl_1519_4095_frms"},
248 {"rmac_ttl_4096_8191_frms"},
249 {"rmac_ttl_8192_max_frms"},
250 {"rmac_ttl_gt_max_frms"},
251 {"rmac_osized_alt_frms"},
252 {"rmac_jabber_alt_frms"},
253 {"rmac_gt_max_alt_frms"},
255 {"rmac_len_discard"},
256 {"rmac_fcs_discard"},
259 {"rmac_red_discard"},
260 {"rmac_rts_discard"},
261 {"rmac_ingm_full_discard"},
265 static char ethtool_driver_stats_keys[][ETH_GSTRING_LEN] = {
266 {"\n DRIVER STATISTICS"},
267 {"single_bit_ecc_errs"},
268 {"double_bit_ecc_errs"},
281 {"alarm_transceiver_temp_high"},
282 {"alarm_transceiver_temp_low"},
283 {"alarm_laser_bias_current_high"},
284 {"alarm_laser_bias_current_low"},
285 {"alarm_laser_output_power_high"},
286 {"alarm_laser_output_power_low"},
287 {"warn_transceiver_temp_high"},
288 {"warn_transceiver_temp_low"},
289 {"warn_laser_bias_current_high"},
290 {"warn_laser_bias_current_low"},
291 {"warn_laser_output_power_high"},
292 {"warn_laser_output_power_low"},
293 {"lro_aggregated_pkts"},
294 {"lro_flush_both_count"},
295 {"lro_out_of_sequence_pkts"},
296 {"lro_flush_due_to_max_pkts"},
297 {"lro_avg_aggr_pkts"},
298 {"mem_alloc_fail_cnt"},
299 {"pci_map_fail_cnt"},
300 {"watchdog_timer_cnt"},
307 {"tx_tcode_buf_abort_cnt"},
308 {"tx_tcode_desc_abort_cnt"},
309 {"tx_tcode_parity_err_cnt"},
310 {"tx_tcode_link_loss_cnt"},
311 {"tx_tcode_list_proc_err_cnt"},
312 {"rx_tcode_parity_err_cnt"},
313 {"rx_tcode_abort_cnt"},
314 {"rx_tcode_parity_abort_cnt"},
315 {"rx_tcode_rda_fail_cnt"},
316 {"rx_tcode_unkn_prot_cnt"},
317 {"rx_tcode_fcs_err_cnt"},
318 {"rx_tcode_buf_size_err_cnt"},
319 {"rx_tcode_rxd_corrupt_cnt"},
320 {"rx_tcode_unkn_err_cnt"},
328 {"mac_tmac_err_cnt"},
329 {"mac_rmac_err_cnt"},
330 {"xgxs_txgxs_err_cnt"},
331 {"xgxs_rxgxs_err_cnt"},
333 {"prc_pcix_err_cnt"},
340 #define S2IO_XENA_STAT_LEN ARRAY_SIZE(ethtool_xena_stats_keys)
341 #define S2IO_ENHANCED_STAT_LEN ARRAY_SIZE(ethtool_enhanced_stats_keys)
342 #define S2IO_DRIVER_STAT_LEN ARRAY_SIZE(ethtool_driver_stats_keys)
344 #define XFRAME_I_STAT_LEN (S2IO_XENA_STAT_LEN + S2IO_DRIVER_STAT_LEN )
345 #define XFRAME_II_STAT_LEN (XFRAME_I_STAT_LEN + S2IO_ENHANCED_STAT_LEN )
347 #define XFRAME_I_STAT_STRINGS_LEN ( XFRAME_I_STAT_LEN * ETH_GSTRING_LEN )
348 #define XFRAME_II_STAT_STRINGS_LEN ( XFRAME_II_STAT_LEN * ETH_GSTRING_LEN )
350 #define S2IO_TEST_LEN ARRAY_SIZE(s2io_gstrings)
351 #define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN
353 #define S2IO_TIMER_CONF(timer, handle, arg, exp) \
354 init_timer(&timer); \
355 timer.function = handle; \
356 timer.data = (unsigned long) arg; \
357 mod_timer(&timer, (jiffies + exp)) \
359 /* copy mac addr to def_mac_addr array */
360 static void do_s2io_copy_mac_addr(struct s2io_nic *sp, int offset, u64 mac_addr)
362 sp->def_mac_addr[offset].mac_addr[5] = (u8) (mac_addr);
363 sp->def_mac_addr[offset].mac_addr[4] = (u8) (mac_addr >> 8);
364 sp->def_mac_addr[offset].mac_addr[3] = (u8) (mac_addr >> 16);
365 sp->def_mac_addr[offset].mac_addr[2] = (u8) (mac_addr >> 24);
366 sp->def_mac_addr[offset].mac_addr[1] = (u8) (mac_addr >> 32);
367 sp->def_mac_addr[offset].mac_addr[0] = (u8) (mac_addr >> 40);
370 static void s2io_vlan_rx_register(struct net_device *dev,
371 struct vlan_group *grp)
374 struct s2io_nic *nic = dev->priv;
375 unsigned long flags[MAX_TX_FIFOS];
376 struct mac_info *mac_control = &nic->mac_control;
377 struct config_param *config = &nic->config;
379 for (i = 0; i < config->tx_fifo_num; i++)
380 spin_lock_irqsave(&mac_control->fifos[i].tx_lock, flags[i]);
383 for (i = config->tx_fifo_num - 1; i >= 0; i--)
384 spin_unlock_irqrestore(&mac_control->fifos[i].tx_lock,
388 /* A flag indicating whether 'RX_PA_CFG_STRIP_VLAN_TAG' bit is set or not */
389 static int vlan_strip_flag;
391 /* Unregister the vlan */
392 static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid)
395 struct s2io_nic *nic = dev->priv;
396 unsigned long flags[MAX_TX_FIFOS];
397 struct mac_info *mac_control = &nic->mac_control;
398 struct config_param *config = &nic->config;
400 for (i = 0; i < config->tx_fifo_num; i++)
401 spin_lock_irqsave(&mac_control->fifos[i].tx_lock, flags[i]);
404 vlan_group_set_device(nic->vlgrp, vid, NULL);
406 for (i = config->tx_fifo_num - 1; i >= 0; i--)
407 spin_unlock_irqrestore(&mac_control->fifos[i].tx_lock,
412 * Constants to be programmed into the Xena's registers, to configure
417 static const u64 herc_act_dtx_cfg[] = {
419 0x8000051536750000ULL, 0x80000515367500E0ULL,
421 0x8000051536750004ULL, 0x80000515367500E4ULL,
423 0x80010515003F0000ULL, 0x80010515003F00E0ULL,
425 0x80010515003F0004ULL, 0x80010515003F00E4ULL,
427 0x801205150D440000ULL, 0x801205150D4400E0ULL,
429 0x801205150D440004ULL, 0x801205150D4400E4ULL,
431 0x80020515F2100000ULL, 0x80020515F21000E0ULL,
433 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
438 static const u64 xena_dtx_cfg[] = {
440 0x8000051500000000ULL, 0x80000515000000E0ULL,
442 0x80000515D9350004ULL, 0x80000515D93500E4ULL,
444 0x8001051500000000ULL, 0x80010515000000E0ULL,
446 0x80010515001E0004ULL, 0x80010515001E00E4ULL,
448 0x8002051500000000ULL, 0x80020515000000E0ULL,
450 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
455 * Constants for Fixing the MacAddress problem seen mostly on
458 static const u64 fix_mac[] = {
459 0x0060000000000000ULL, 0x0060600000000000ULL,
460 0x0040600000000000ULL, 0x0000600000000000ULL,
461 0x0020600000000000ULL, 0x0060600000000000ULL,
462 0x0020600000000000ULL, 0x0060600000000000ULL,
463 0x0020600000000000ULL, 0x0060600000000000ULL,
464 0x0020600000000000ULL, 0x0060600000000000ULL,
465 0x0020600000000000ULL, 0x0060600000000000ULL,
466 0x0020600000000000ULL, 0x0060600000000000ULL,
467 0x0020600000000000ULL, 0x0060600000000000ULL,
468 0x0020600000000000ULL, 0x0060600000000000ULL,
469 0x0020600000000000ULL, 0x0060600000000000ULL,
470 0x0020600000000000ULL, 0x0060600000000000ULL,
471 0x0020600000000000ULL, 0x0000600000000000ULL,
472 0x0040600000000000ULL, 0x0060600000000000ULL,
476 MODULE_LICENSE("GPL");
477 MODULE_VERSION(DRV_VERSION);
480 /* Module Loadable parameters. */
481 S2IO_PARM_INT(tx_fifo_num, FIFO_DEFAULT_NUM);
482 S2IO_PARM_INT(rx_ring_num, 1);
483 S2IO_PARM_INT(multiq, 0);
484 S2IO_PARM_INT(rx_ring_mode, 1);
485 S2IO_PARM_INT(use_continuous_tx_intrs, 1);
486 S2IO_PARM_INT(rmac_pause_time, 0x100);
487 S2IO_PARM_INT(mc_pause_threshold_q0q3, 187);
488 S2IO_PARM_INT(mc_pause_threshold_q4q7, 187);
489 S2IO_PARM_INT(shared_splits, 0);
490 S2IO_PARM_INT(tmac_util_period, 5);
491 S2IO_PARM_INT(rmac_util_period, 5);
492 S2IO_PARM_INT(l3l4hdr_size, 128);
493 /* 0 is no steering, 1 is Priority steering, 2 is Default steering */
494 S2IO_PARM_INT(tx_steering_type, TX_DEFAULT_STEERING);
495 /* Frequency of Rx desc syncs expressed as power of 2 */
496 S2IO_PARM_INT(rxsync_frequency, 3);
497 /* Interrupt type. Values can be 0(INTA), 2(MSI_X) */
498 S2IO_PARM_INT(intr_type, 2);
499 /* Large receive offload feature */
500 static unsigned int lro_enable;
501 module_param_named(lro, lro_enable, uint, 0);
503 /* Max pkts to be aggregated by LRO at one time. If not specified,
504 * aggregation happens until we hit max IP pkt size(64K)
506 S2IO_PARM_INT(lro_max_pkts, 0xFFFF);
507 S2IO_PARM_INT(indicate_max_pkts, 0);
509 S2IO_PARM_INT(napi, 1);
510 S2IO_PARM_INT(ufo, 0);
511 S2IO_PARM_INT(vlan_tag_strip, NO_STRIP_IN_PROMISC);
513 static unsigned int tx_fifo_len[MAX_TX_FIFOS] =
514 {DEFAULT_FIFO_0_LEN, [1 ...(MAX_TX_FIFOS - 1)] = DEFAULT_FIFO_1_7_LEN};
515 static unsigned int rx_ring_sz[MAX_RX_RINGS] =
516 {[0 ...(MAX_RX_RINGS - 1)] = SMALL_BLK_CNT};
517 static unsigned int rts_frm_len[MAX_RX_RINGS] =
518 {[0 ...(MAX_RX_RINGS - 1)] = 0 };
520 module_param_array(tx_fifo_len, uint, NULL, 0);
521 module_param_array(rx_ring_sz, uint, NULL, 0);
522 module_param_array(rts_frm_len, uint, NULL, 0);
526 * This table lists all the devices that this driver supports.
528 static struct pci_device_id s2io_tbl[] __devinitdata = {
529 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_WIN,
530 PCI_ANY_ID, PCI_ANY_ID},
531 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_UNI,
532 PCI_ANY_ID, PCI_ANY_ID},
533 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_WIN,
534 PCI_ANY_ID, PCI_ANY_ID},
535 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI,
536 PCI_ANY_ID, PCI_ANY_ID},
540 MODULE_DEVICE_TABLE(pci, s2io_tbl);
542 static struct pci_error_handlers s2io_err_handler = {
543 .error_detected = s2io_io_error_detected,
544 .slot_reset = s2io_io_slot_reset,
545 .resume = s2io_io_resume,
548 static struct pci_driver s2io_driver = {
550 .id_table = s2io_tbl,
551 .probe = s2io_init_nic,
552 .remove = __devexit_p(s2io_rem_nic),
553 .err_handler = &s2io_err_handler,
556 /* A simplifier macro used both by init and free shared_mem Fns(). */
557 #define TXD_MEM_PAGE_CNT(len, per_each) ((len+per_each - 1) / per_each)
559 /* netqueue manipulation helper functions */
560 static inline void s2io_stop_all_tx_queue(struct s2io_nic *sp)
563 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
564 if (sp->config.multiq) {
565 for (i = 0; i < sp->config.tx_fifo_num; i++)
566 netif_stop_subqueue(sp->dev, i);
570 for (i = 0; i < sp->config.tx_fifo_num; i++)
571 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_STOP;
572 netif_stop_queue(sp->dev);
576 static inline void s2io_stop_tx_queue(struct s2io_nic *sp, int fifo_no)
578 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
579 if (sp->config.multiq)
580 netif_stop_subqueue(sp->dev, fifo_no);
584 sp->mac_control.fifos[fifo_no].queue_state =
586 netif_stop_queue(sp->dev);
590 static inline void s2io_start_all_tx_queue(struct s2io_nic *sp)
593 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
594 if (sp->config.multiq) {
595 for (i = 0; i < sp->config.tx_fifo_num; i++)
596 netif_start_subqueue(sp->dev, i);
600 for (i = 0; i < sp->config.tx_fifo_num; i++)
601 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_START;
602 netif_start_queue(sp->dev);
606 static inline void s2io_start_tx_queue(struct s2io_nic *sp, int fifo_no)
608 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
609 if (sp->config.multiq)
610 netif_start_subqueue(sp->dev, fifo_no);
614 sp->mac_control.fifos[fifo_no].queue_state =
616 netif_start_queue(sp->dev);
620 static inline void s2io_wake_all_tx_queue(struct s2io_nic *sp)
623 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
624 if (sp->config.multiq) {
625 for (i = 0; i < sp->config.tx_fifo_num; i++)
626 netif_wake_subqueue(sp->dev, i);
630 for (i = 0; i < sp->config.tx_fifo_num; i++)
631 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_START;
632 netif_wake_queue(sp->dev);
636 static inline void s2io_wake_tx_queue(
637 struct fifo_info *fifo, int cnt, u8 multiq)
640 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
642 if (cnt && __netif_subqueue_stopped(fifo->dev, fifo->fifo_no))
643 netif_wake_subqueue(fifo->dev, fifo->fifo_no);
646 if (cnt && (fifo->queue_state == FIFO_QUEUE_STOP)) {
647 if (netif_queue_stopped(fifo->dev)) {
648 fifo->queue_state = FIFO_QUEUE_START;
649 netif_wake_queue(fifo->dev);
655 * init_shared_mem - Allocation and Initialization of Memory
656 * @nic: Device private variable.
657 * Description: The function allocates all the memory areas shared
658 * between the NIC and the driver. This includes Tx descriptors,
659 * Rx descriptors and the statistics block.
662 static int init_shared_mem(struct s2io_nic *nic)
665 void *tmp_v_addr, *tmp_v_addr_next;
666 dma_addr_t tmp_p_addr, tmp_p_addr_next;
667 struct RxD_block *pre_rxd_blk = NULL;
669 int lst_size, lst_per_page;
670 struct net_device *dev = nic->dev;
674 struct mac_info *mac_control;
675 struct config_param *config;
676 unsigned long long mem_allocated = 0;
678 mac_control = &nic->mac_control;
679 config = &nic->config;
682 /* Allocation and initialization of TXDLs in FIOFs */
684 for (i = 0; i < config->tx_fifo_num; i++) {
685 size += config->tx_cfg[i].fifo_len;
687 if (size > MAX_AVAILABLE_TXDS) {
688 DBG_PRINT(ERR_DBG, "s2io: Requested TxDs too high, ");
689 DBG_PRINT(ERR_DBG, "Requested: %d, max supported: 8192\n", size);
694 for (i = 0; i < config->tx_fifo_num; i++) {
695 size = config->tx_cfg[i].fifo_len;
697 * Legal values are from 2 to 8192
700 DBG_PRINT(ERR_DBG, "s2io: Invalid fifo len (%d)", size);
701 DBG_PRINT(ERR_DBG, "for fifo %d\n", i);
702 DBG_PRINT(ERR_DBG, "s2io: Legal values for fifo len"
708 lst_size = (sizeof(struct TxD) * config->max_txds);
709 lst_per_page = PAGE_SIZE / lst_size;
711 for (i = 0; i < config->tx_fifo_num; i++) {
712 int fifo_len = config->tx_cfg[i].fifo_len;
713 int list_holder_size = fifo_len * sizeof(struct list_info_hold);
714 mac_control->fifos[i].list_info = kzalloc(list_holder_size,
716 if (!mac_control->fifos[i].list_info) {
718 "Malloc failed for list_info\n");
721 mem_allocated += list_holder_size;
723 for (i = 0; i < config->tx_fifo_num; i++) {
724 int page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
726 mac_control->fifos[i].tx_curr_put_info.offset = 0;
727 mac_control->fifos[i].tx_curr_put_info.fifo_len =
728 config->tx_cfg[i].fifo_len - 1;
729 mac_control->fifos[i].tx_curr_get_info.offset = 0;
730 mac_control->fifos[i].tx_curr_get_info.fifo_len =
731 config->tx_cfg[i].fifo_len - 1;
732 mac_control->fifos[i].fifo_no = i;
733 mac_control->fifos[i].nic = nic;
734 mac_control->fifos[i].max_txds = MAX_SKB_FRAGS + 2;
735 mac_control->fifos[i].dev = dev;
737 for (j = 0; j < page_num; j++) {
741 tmp_v = pci_alloc_consistent(nic->pdev,
745 "pci_alloc_consistent ");
746 DBG_PRINT(INFO_DBG, "failed for TxDL\n");
749 /* If we got a zero DMA address(can happen on
750 * certain platforms like PPC), reallocate.
751 * Store virtual address of page we don't want,
755 mac_control->zerodma_virt_addr = tmp_v;
757 "%s: Zero DMA address for TxDL. ", dev->name);
759 "Virtual address %p\n", tmp_v);
760 tmp_v = pci_alloc_consistent(nic->pdev,
764 "pci_alloc_consistent ");
765 DBG_PRINT(INFO_DBG, "failed for TxDL\n");
768 mem_allocated += PAGE_SIZE;
770 while (k < lst_per_page) {
771 int l = (j * lst_per_page) + k;
772 if (l == config->tx_cfg[i].fifo_len)
774 mac_control->fifos[i].list_info[l].list_virt_addr =
775 tmp_v + (k * lst_size);
776 mac_control->fifos[i].list_info[l].list_phy_addr =
777 tmp_p + (k * lst_size);
783 for (i = 0; i < config->tx_fifo_num; i++) {
784 size = config->tx_cfg[i].fifo_len;
785 mac_control->fifos[i].ufo_in_band_v
786 = kcalloc(size, sizeof(u64), GFP_KERNEL);
787 if (!mac_control->fifos[i].ufo_in_band_v)
789 mem_allocated += (size * sizeof(u64));
792 /* Allocation and initialization of RXDs in Rings */
794 for (i = 0; i < config->rx_ring_num; i++) {
795 if (config->rx_cfg[i].num_rxd %
796 (rxd_count[nic->rxd_mode] + 1)) {
797 DBG_PRINT(ERR_DBG, "%s: RxD count of ", dev->name);
798 DBG_PRINT(ERR_DBG, "Ring%d is not a multiple of ",
800 DBG_PRINT(ERR_DBG, "RxDs per Block");
803 size += config->rx_cfg[i].num_rxd;
804 mac_control->rings[i].block_count =
805 config->rx_cfg[i].num_rxd /
806 (rxd_count[nic->rxd_mode] + 1 );
807 mac_control->rings[i].pkt_cnt = config->rx_cfg[i].num_rxd -
808 mac_control->rings[i].block_count;
810 if (nic->rxd_mode == RXD_MODE_1)
811 size = (size * (sizeof(struct RxD1)));
813 size = (size * (sizeof(struct RxD3)));
815 for (i = 0; i < config->rx_ring_num; i++) {
816 mac_control->rings[i].rx_curr_get_info.block_index = 0;
817 mac_control->rings[i].rx_curr_get_info.offset = 0;
818 mac_control->rings[i].rx_curr_get_info.ring_len =
819 config->rx_cfg[i].num_rxd - 1;
820 mac_control->rings[i].rx_curr_put_info.block_index = 0;
821 mac_control->rings[i].rx_curr_put_info.offset = 0;
822 mac_control->rings[i].rx_curr_put_info.ring_len =
823 config->rx_cfg[i].num_rxd - 1;
824 mac_control->rings[i].nic = nic;
825 mac_control->rings[i].ring_no = i;
827 blk_cnt = config->rx_cfg[i].num_rxd /
828 (rxd_count[nic->rxd_mode] + 1);
829 /* Allocating all the Rx blocks */
830 for (j = 0; j < blk_cnt; j++) {
831 struct rx_block_info *rx_blocks;
834 rx_blocks = &mac_control->rings[i].rx_blocks[j];
835 size = SIZE_OF_BLOCK; //size is always page size
836 tmp_v_addr = pci_alloc_consistent(nic->pdev, size,
838 if (tmp_v_addr == NULL) {
840 * In case of failure, free_shared_mem()
841 * is called, which should free any
842 * memory that was alloced till the
845 rx_blocks->block_virt_addr = tmp_v_addr;
848 mem_allocated += size;
849 memset(tmp_v_addr, 0, size);
850 rx_blocks->block_virt_addr = tmp_v_addr;
851 rx_blocks->block_dma_addr = tmp_p_addr;
852 rx_blocks->rxds = kmalloc(sizeof(struct rxd_info)*
853 rxd_count[nic->rxd_mode],
855 if (!rx_blocks->rxds)
858 (sizeof(struct rxd_info)* rxd_count[nic->rxd_mode]);
859 for (l=0; l<rxd_count[nic->rxd_mode];l++) {
860 rx_blocks->rxds[l].virt_addr =
861 rx_blocks->block_virt_addr +
862 (rxd_size[nic->rxd_mode] * l);
863 rx_blocks->rxds[l].dma_addr =
864 rx_blocks->block_dma_addr +
865 (rxd_size[nic->rxd_mode] * l);
868 /* Interlinking all Rx Blocks */
869 for (j = 0; j < blk_cnt; j++) {
871 mac_control->rings[i].rx_blocks[j].block_virt_addr;
873 mac_control->rings[i].rx_blocks[(j + 1) %
874 blk_cnt].block_virt_addr;
876 mac_control->rings[i].rx_blocks[j].block_dma_addr;
878 mac_control->rings[i].rx_blocks[(j + 1) %
879 blk_cnt].block_dma_addr;
881 pre_rxd_blk = (struct RxD_block *) tmp_v_addr;
882 pre_rxd_blk->reserved_2_pNext_RxD_block =
883 (unsigned long) tmp_v_addr_next;
884 pre_rxd_blk->pNext_RxD_Blk_physical =
885 (u64) tmp_p_addr_next;
888 if (nic->rxd_mode == RXD_MODE_3B) {
890 * Allocation of Storages for buffer addresses in 2BUFF mode
891 * and the buffers as well.
893 for (i = 0; i < config->rx_ring_num; i++) {
894 blk_cnt = config->rx_cfg[i].num_rxd /
895 (rxd_count[nic->rxd_mode]+ 1);
896 mac_control->rings[i].ba =
897 kmalloc((sizeof(struct buffAdd *) * blk_cnt),
899 if (!mac_control->rings[i].ba)
901 mem_allocated +=(sizeof(struct buffAdd *) * blk_cnt);
902 for (j = 0; j < blk_cnt; j++) {
904 mac_control->rings[i].ba[j] =
905 kmalloc((sizeof(struct buffAdd) *
906 (rxd_count[nic->rxd_mode] + 1)),
908 if (!mac_control->rings[i].ba[j])
910 mem_allocated += (sizeof(struct buffAdd) * \
911 (rxd_count[nic->rxd_mode] + 1));
912 while (k != rxd_count[nic->rxd_mode]) {
913 ba = &mac_control->rings[i].ba[j][k];
915 ba->ba_0_org = (void *) kmalloc
916 (BUF0_LEN + ALIGN_SIZE, GFP_KERNEL);
920 (BUF0_LEN + ALIGN_SIZE);
921 tmp = (unsigned long)ba->ba_0_org;
923 tmp &= ~((unsigned long) ALIGN_SIZE);
924 ba->ba_0 = (void *) tmp;
926 ba->ba_1_org = (void *) kmalloc
927 (BUF1_LEN + ALIGN_SIZE, GFP_KERNEL);
931 += (BUF1_LEN + ALIGN_SIZE);
932 tmp = (unsigned long) ba->ba_1_org;
934 tmp &= ~((unsigned long) ALIGN_SIZE);
935 ba->ba_1 = (void *) tmp;
942 /* Allocation and initialization of Statistics block */
943 size = sizeof(struct stat_block);
944 mac_control->stats_mem = pci_alloc_consistent
945 (nic->pdev, size, &mac_control->stats_mem_phy);
947 if (!mac_control->stats_mem) {
949 * In case of failure, free_shared_mem() is called, which
950 * should free any memory that was alloced till the
955 mem_allocated += size;
956 mac_control->stats_mem_sz = size;
958 tmp_v_addr = mac_control->stats_mem;
959 mac_control->stats_info = (struct stat_block *) tmp_v_addr;
960 memset(tmp_v_addr, 0, size);
961 DBG_PRINT(INIT_DBG, "%s:Ring Mem PHY: 0x%llx\n", dev->name,
962 (unsigned long long) tmp_p_addr);
963 mac_control->stats_info->sw_stat.mem_allocated += mem_allocated;
968 * free_shared_mem - Free the allocated Memory
969 * @nic: Device private variable.
970 * Description: This function is to free all memory locations allocated by
971 * the init_shared_mem() function and return it to the kernel.
974 static void free_shared_mem(struct s2io_nic *nic)
976 int i, j, blk_cnt, size;
978 dma_addr_t tmp_p_addr;
979 struct mac_info *mac_control;
980 struct config_param *config;
981 int lst_size, lst_per_page;
982 struct net_device *dev;
990 mac_control = &nic->mac_control;
991 config = &nic->config;
993 lst_size = (sizeof(struct TxD) * config->max_txds);
994 lst_per_page = PAGE_SIZE / lst_size;
996 for (i = 0; i < config->tx_fifo_num; i++) {
997 page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
999 for (j = 0; j < page_num; j++) {
1000 int mem_blks = (j * lst_per_page);
1001 if (!mac_control->fifos[i].list_info)
1003 if (!mac_control->fifos[i].list_info[mem_blks].
1006 pci_free_consistent(nic->pdev, PAGE_SIZE,
1007 mac_control->fifos[i].
1008 list_info[mem_blks].
1010 mac_control->fifos[i].
1011 list_info[mem_blks].
1013 nic->mac_control.stats_info->sw_stat.mem_freed
1016 /* If we got a zero DMA address during allocation,
1019 if (mac_control->zerodma_virt_addr) {
1020 pci_free_consistent(nic->pdev, PAGE_SIZE,
1021 mac_control->zerodma_virt_addr,
1024 "%s: Freeing TxDL with zero DMA addr. ",
1026 DBG_PRINT(INIT_DBG, "Virtual address %p\n",
1027 mac_control->zerodma_virt_addr);
1028 nic->mac_control.stats_info->sw_stat.mem_freed
1031 kfree(mac_control->fifos[i].list_info);
1032 nic->mac_control.stats_info->sw_stat.mem_freed +=
1033 (nic->config.tx_cfg[i].fifo_len *sizeof(struct list_info_hold));
1036 size = SIZE_OF_BLOCK;
1037 for (i = 0; i < config->rx_ring_num; i++) {
1038 blk_cnt = mac_control->rings[i].block_count;
1039 for (j = 0; j < blk_cnt; j++) {
1040 tmp_v_addr = mac_control->rings[i].rx_blocks[j].
1042 tmp_p_addr = mac_control->rings[i].rx_blocks[j].
1044 if (tmp_v_addr == NULL)
1046 pci_free_consistent(nic->pdev, size,
1047 tmp_v_addr, tmp_p_addr);
1048 nic->mac_control.stats_info->sw_stat.mem_freed += size;
1049 kfree(mac_control->rings[i].rx_blocks[j].rxds);
1050 nic->mac_control.stats_info->sw_stat.mem_freed +=
1051 ( sizeof(struct rxd_info)* rxd_count[nic->rxd_mode]);
1055 if (nic->rxd_mode == RXD_MODE_3B) {
1056 /* Freeing buffer storage addresses in 2BUFF mode. */
1057 for (i = 0; i < config->rx_ring_num; i++) {
1058 blk_cnt = config->rx_cfg[i].num_rxd /
1059 (rxd_count[nic->rxd_mode] + 1);
1060 for (j = 0; j < blk_cnt; j++) {
1062 if (!mac_control->rings[i].ba[j])
1064 while (k != rxd_count[nic->rxd_mode]) {
1065 struct buffAdd *ba =
1066 &mac_control->rings[i].ba[j][k];
1067 kfree(ba->ba_0_org);
1068 nic->mac_control.stats_info->sw_stat.\
1069 mem_freed += (BUF0_LEN + ALIGN_SIZE);
1070 kfree(ba->ba_1_org);
1071 nic->mac_control.stats_info->sw_stat.\
1072 mem_freed += (BUF1_LEN + ALIGN_SIZE);
1075 kfree(mac_control->rings[i].ba[j]);
1076 nic->mac_control.stats_info->sw_stat.mem_freed +=
1077 (sizeof(struct buffAdd) *
1078 (rxd_count[nic->rxd_mode] + 1));
1080 kfree(mac_control->rings[i].ba);
1081 nic->mac_control.stats_info->sw_stat.mem_freed +=
1082 (sizeof(struct buffAdd *) * blk_cnt);
1086 for (i = 0; i < nic->config.tx_fifo_num; i++) {
1087 if (mac_control->fifos[i].ufo_in_band_v) {
1088 nic->mac_control.stats_info->sw_stat.mem_freed
1089 += (config->tx_cfg[i].fifo_len * sizeof(u64));
1090 kfree(mac_control->fifos[i].ufo_in_band_v);
1094 if (mac_control->stats_mem) {
1095 nic->mac_control.stats_info->sw_stat.mem_freed +=
1096 mac_control->stats_mem_sz;
1097 pci_free_consistent(nic->pdev,
1098 mac_control->stats_mem_sz,
1099 mac_control->stats_mem,
1100 mac_control->stats_mem_phy);
1105 * s2io_verify_pci_mode -
1108 static int s2io_verify_pci_mode(struct s2io_nic *nic)
1110 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1111 register u64 val64 = 0;
1114 val64 = readq(&bar0->pci_mode);
1115 mode = (u8)GET_PCI_MODE(val64);
1117 if ( val64 & PCI_MODE_UNKNOWN_MODE)
1118 return -1; /* Unknown PCI mode */
1122 #define NEC_VENID 0x1033
1123 #define NEC_DEVID 0x0125
1124 static int s2io_on_nec_bridge(struct pci_dev *s2io_pdev)
1126 struct pci_dev *tdev = NULL;
1127 while ((tdev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, tdev)) != NULL) {
1128 if (tdev->vendor == NEC_VENID && tdev->device == NEC_DEVID) {
1129 if (tdev->bus == s2io_pdev->bus->parent)
1137 static int bus_speed[8] = {33, 133, 133, 200, 266, 133, 200, 266};
1139 * s2io_print_pci_mode -
1141 static int s2io_print_pci_mode(struct s2io_nic *nic)
1143 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1144 register u64 val64 = 0;
1146 struct config_param *config = &nic->config;
1148 val64 = readq(&bar0->pci_mode);
1149 mode = (u8)GET_PCI_MODE(val64);
1151 if ( val64 & PCI_MODE_UNKNOWN_MODE)
1152 return -1; /* Unknown PCI mode */
1154 config->bus_speed = bus_speed[mode];
1156 if (s2io_on_nec_bridge(nic->pdev)) {
1157 DBG_PRINT(ERR_DBG, "%s: Device is on PCI-E bus\n",
1162 if (val64 & PCI_MODE_32_BITS) {
1163 DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
1165 DBG_PRINT(ERR_DBG, "%s: Device is on 64 bit ", nic->dev->name);
1169 case PCI_MODE_PCI_33:
1170 DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
1172 case PCI_MODE_PCI_66:
1173 DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
1175 case PCI_MODE_PCIX_M1_66:
1176 DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
1178 case PCI_MODE_PCIX_M1_100:
1179 DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
1181 case PCI_MODE_PCIX_M1_133:
1182 DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
1184 case PCI_MODE_PCIX_M2_66:
1185 DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
1187 case PCI_MODE_PCIX_M2_100:
1188 DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
1190 case PCI_MODE_PCIX_M2_133:
1191 DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
1194 return -1; /* Unsupported bus speed */
1201 * init_tti - Initialization transmit traffic interrupt scheme
1202 * @nic: device private variable
1203 * @link: link status (UP/DOWN) used to enable/disable continuous
1204 * transmit interrupts
1205 * Description: The function configures transmit traffic interrupts
1206 * Return Value: SUCCESS on success and
1210 static int init_tti(struct s2io_nic *nic, int link)
1212 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1213 register u64 val64 = 0;
1215 struct config_param *config;
1217 config = &nic->config;
1219 for (i = 0; i < config->tx_fifo_num; i++) {
1221 * TTI Initialization. Default Tx timer gets us about
1222 * 250 interrupts per sec. Continuous interrupts are enabled
1225 if (nic->device_type == XFRAME_II_DEVICE) {
1226 int count = (nic->config.bus_speed * 125)/2;
1227 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count);
1229 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078);
1231 val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) |
1232 TTI_DATA1_MEM_TX_URNG_B(0x10) |
1233 TTI_DATA1_MEM_TX_URNG_C(0x30) |
1234 TTI_DATA1_MEM_TX_TIMER_AC_EN;
1236 if (use_continuous_tx_intrs && (link == LINK_UP))
1237 val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
1238 writeq(val64, &bar0->tti_data1_mem);
1240 val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
1241 TTI_DATA2_MEM_TX_UFC_B(0x20) |
1242 TTI_DATA2_MEM_TX_UFC_C(0x40) |
1243 TTI_DATA2_MEM_TX_UFC_D(0x80);
1245 writeq(val64, &bar0->tti_data2_mem);
1247 val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD |
1248 TTI_CMD_MEM_OFFSET(i);
1249 writeq(val64, &bar0->tti_command_mem);
1251 if (wait_for_cmd_complete(&bar0->tti_command_mem,
1252 TTI_CMD_MEM_STROBE_NEW_CMD, S2IO_BIT_RESET) != SUCCESS)
1260 * init_nic - Initialization of hardware
1261 * @nic: device private variable
1262 * Description: The function sequentially configures every block
1263 * of the H/W from their reset values.
1264 * Return Value: SUCCESS on success and
1265 * '-1' on failure (endian settings incorrect).
1268 static int init_nic(struct s2io_nic *nic)
1270 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1271 struct net_device *dev = nic->dev;
1272 register u64 val64 = 0;
1276 struct mac_info *mac_control;
1277 struct config_param *config;
1279 unsigned long long mem_share;
1282 mac_control = &nic->mac_control;
1283 config = &nic->config;
1285 /* to set the swapper controle on the card */
1286 if(s2io_set_swapper(nic)) {
1287 DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n");
1292 * Herc requires EOI to be removed from reset before XGXS, so..
1294 if (nic->device_type & XFRAME_II_DEVICE) {
1295 val64 = 0xA500000000ULL;
1296 writeq(val64, &bar0->sw_reset);
1298 val64 = readq(&bar0->sw_reset);
1301 /* Remove XGXS from reset state */
1303 writeq(val64, &bar0->sw_reset);
1305 val64 = readq(&bar0->sw_reset);
1307 /* Ensure that it's safe to access registers by checking
1308 * RIC_RUNNING bit is reset. Check is valid only for XframeII.
1310 if (nic->device_type == XFRAME_II_DEVICE) {
1311 for (i = 0; i < 50; i++) {
1312 val64 = readq(&bar0->adapter_status);
1313 if (!(val64 & ADAPTER_STATUS_RIC_RUNNING))
1321 /* Enable Receiving broadcasts */
1322 add = &bar0->mac_cfg;
1323 val64 = readq(&bar0->mac_cfg);
1324 val64 |= MAC_RMAC_BCAST_ENABLE;
1325 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1326 writel((u32) val64, add);
1327 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1328 writel((u32) (val64 >> 32), (add + 4));
1330 /* Read registers in all blocks */
1331 val64 = readq(&bar0->mac_int_mask);
1332 val64 = readq(&bar0->mc_int_mask);
1333 val64 = readq(&bar0->xgxs_int_mask);
1337 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
1339 if (nic->device_type & XFRAME_II_DEVICE) {
1340 while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
1341 SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
1342 &bar0->dtx_control, UF);
1344 msleep(1); /* Necessary!! */
1348 while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
1349 SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
1350 &bar0->dtx_control, UF);
1351 val64 = readq(&bar0->dtx_control);
1356 /* Tx DMA Initialization */
1358 writeq(val64, &bar0->tx_fifo_partition_0);
1359 writeq(val64, &bar0->tx_fifo_partition_1);
1360 writeq(val64, &bar0->tx_fifo_partition_2);
1361 writeq(val64, &bar0->tx_fifo_partition_3);
1364 for (i = 0, j = 0; i < config->tx_fifo_num; i++) {
1366 vBIT(config->tx_cfg[i].fifo_len - 1, ((j * 32) + 19),
1367 13) | vBIT(config->tx_cfg[i].fifo_priority,
1370 if (i == (config->tx_fifo_num - 1)) {
1377 writeq(val64, &bar0->tx_fifo_partition_0);
1382 writeq(val64, &bar0->tx_fifo_partition_1);
1387 writeq(val64, &bar0->tx_fifo_partition_2);
1392 writeq(val64, &bar0->tx_fifo_partition_3);
1403 * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug
1404 * SXE-008 TRANSMIT DMA ARBITRATION ISSUE.
1406 if ((nic->device_type == XFRAME_I_DEVICE) &&
1407 (nic->pdev->revision < 4))
1408 writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable);
1410 val64 = readq(&bar0->tx_fifo_partition_0);
1411 DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n",
1412 &bar0->tx_fifo_partition_0, (unsigned long long) val64);
1415 * Initialization of Tx_PA_CONFIG register to ignore packet
1416 * integrity checking.
1418 val64 = readq(&bar0->tx_pa_cfg);
1419 val64 |= TX_PA_CFG_IGNORE_FRM_ERR | TX_PA_CFG_IGNORE_SNAP_OUI |
1420 TX_PA_CFG_IGNORE_LLC_CTRL | TX_PA_CFG_IGNORE_L2_ERR;
1421 writeq(val64, &bar0->tx_pa_cfg);
1423 /* Rx DMA intialization. */
1425 for (i = 0; i < config->rx_ring_num; i++) {
1427 vBIT(config->rx_cfg[i].ring_priority, (5 + (i * 8)),
1430 writeq(val64, &bar0->rx_queue_priority);
1433 * Allocating equal share of memory to all the
1437 if (nic->device_type & XFRAME_II_DEVICE)
1442 for (i = 0; i < config->rx_ring_num; i++) {
1445 mem_share = (mem_size / config->rx_ring_num +
1446 mem_size % config->rx_ring_num);
1447 val64 |= RX_QUEUE_CFG_Q0_SZ(mem_share);
1450 mem_share = (mem_size / config->rx_ring_num);
1451 val64 |= RX_QUEUE_CFG_Q1_SZ(mem_share);
1454 mem_share = (mem_size / config->rx_ring_num);
1455 val64 |= RX_QUEUE_CFG_Q2_SZ(mem_share);
1458 mem_share = (mem_size / config->rx_ring_num);
1459 val64 |= RX_QUEUE_CFG_Q3_SZ(mem_share);
1462 mem_share = (mem_size / config->rx_ring_num);
1463 val64 |= RX_QUEUE_CFG_Q4_SZ(mem_share);
1466 mem_share = (mem_size / config->rx_ring_num);
1467 val64 |= RX_QUEUE_CFG_Q5_SZ(mem_share);
1470 mem_share = (mem_size / config->rx_ring_num);
1471 val64 |= RX_QUEUE_CFG_Q6_SZ(mem_share);
1474 mem_share = (mem_size / config->rx_ring_num);
1475 val64 |= RX_QUEUE_CFG_Q7_SZ(mem_share);
1479 writeq(val64, &bar0->rx_queue_cfg);
1482 * Filling Tx round robin registers
1483 * as per the number of FIFOs for equal scheduling priority
1485 switch (config->tx_fifo_num) {
1488 writeq(val64, &bar0->tx_w_round_robin_0);
1489 writeq(val64, &bar0->tx_w_round_robin_1);
1490 writeq(val64, &bar0->tx_w_round_robin_2);
1491 writeq(val64, &bar0->tx_w_round_robin_3);
1492 writeq(val64, &bar0->tx_w_round_robin_4);
1495 val64 = 0x0001000100010001ULL;
1496 writeq(val64, &bar0->tx_w_round_robin_0);
1497 writeq(val64, &bar0->tx_w_round_robin_1);
1498 writeq(val64, &bar0->tx_w_round_robin_2);
1499 writeq(val64, &bar0->tx_w_round_robin_3);
1500 val64 = 0x0001000100000000ULL;
1501 writeq(val64, &bar0->tx_w_round_robin_4);
1504 val64 = 0x0001020001020001ULL;
1505 writeq(val64, &bar0->tx_w_round_robin_0);
1506 val64 = 0x0200010200010200ULL;
1507 writeq(val64, &bar0->tx_w_round_robin_1);
1508 val64 = 0x0102000102000102ULL;
1509 writeq(val64, &bar0->tx_w_round_robin_2);
1510 val64 = 0x0001020001020001ULL;
1511 writeq(val64, &bar0->tx_w_round_robin_3);
1512 val64 = 0x0200010200000000ULL;
1513 writeq(val64, &bar0->tx_w_round_robin_4);
1516 val64 = 0x0001020300010203ULL;
1517 writeq(val64, &bar0->tx_w_round_robin_0);
1518 writeq(val64, &bar0->tx_w_round_robin_1);
1519 writeq(val64, &bar0->tx_w_round_robin_2);
1520 writeq(val64, &bar0->tx_w_round_robin_3);
1521 val64 = 0x0001020300000000ULL;
1522 writeq(val64, &bar0->tx_w_round_robin_4);
1525 val64 = 0x0001020304000102ULL;
1526 writeq(val64, &bar0->tx_w_round_robin_0);
1527 val64 = 0x0304000102030400ULL;
1528 writeq(val64, &bar0->tx_w_round_robin_1);
1529 val64 = 0x0102030400010203ULL;
1530 writeq(val64, &bar0->tx_w_round_robin_2);
1531 val64 = 0x0400010203040001ULL;
1532 writeq(val64, &bar0->tx_w_round_robin_3);
1533 val64 = 0x0203040000000000ULL;
1534 writeq(val64, &bar0->tx_w_round_robin_4);
1537 val64 = 0x0001020304050001ULL;
1538 writeq(val64, &bar0->tx_w_round_robin_0);
1539 val64 = 0x0203040500010203ULL;
1540 writeq(val64, &bar0->tx_w_round_robin_1);
1541 val64 = 0x0405000102030405ULL;
1542 writeq(val64, &bar0->tx_w_round_robin_2);
1543 val64 = 0x0001020304050001ULL;
1544 writeq(val64, &bar0->tx_w_round_robin_3);
1545 val64 = 0x0203040500000000ULL;
1546 writeq(val64, &bar0->tx_w_round_robin_4);
1549 val64 = 0x0001020304050600ULL;
1550 writeq(val64, &bar0->tx_w_round_robin_0);
1551 val64 = 0x0102030405060001ULL;
1552 writeq(val64, &bar0->tx_w_round_robin_1);
1553 val64 = 0x0203040506000102ULL;
1554 writeq(val64, &bar0->tx_w_round_robin_2);
1555 val64 = 0x0304050600010203ULL;
1556 writeq(val64, &bar0->tx_w_round_robin_3);
1557 val64 = 0x0405060000000000ULL;
1558 writeq(val64, &bar0->tx_w_round_robin_4);
1561 val64 = 0x0001020304050607ULL;
1562 writeq(val64, &bar0->tx_w_round_robin_0);
1563 writeq(val64, &bar0->tx_w_round_robin_1);
1564 writeq(val64, &bar0->tx_w_round_robin_2);
1565 writeq(val64, &bar0->tx_w_round_robin_3);
1566 val64 = 0x0001020300000000ULL;
1567 writeq(val64, &bar0->tx_w_round_robin_4);
1571 /* Enable all configured Tx FIFO partitions */
1572 val64 = readq(&bar0->tx_fifo_partition_0);
1573 val64 |= (TX_FIFO_PARTITION_EN);
1574 writeq(val64, &bar0->tx_fifo_partition_0);
1576 /* Filling the Rx round robin registers as per the
1577 * number of Rings and steering based on QoS.
1579 switch (config->rx_ring_num) {
1581 val64 = 0x8080808080808080ULL;
1582 writeq(val64, &bar0->rts_qos_steering);
1585 val64 = 0x0000010000010000ULL;
1586 writeq(val64, &bar0->rx_w_round_robin_0);
1587 val64 = 0x0100000100000100ULL;
1588 writeq(val64, &bar0->rx_w_round_robin_1);
1589 val64 = 0x0001000001000001ULL;
1590 writeq(val64, &bar0->rx_w_round_robin_2);
1591 val64 = 0x0000010000010000ULL;
1592 writeq(val64, &bar0->rx_w_round_robin_3);
1593 val64 = 0x0100000000000000ULL;
1594 writeq(val64, &bar0->rx_w_round_robin_4);
1596 val64 = 0x8080808040404040ULL;
1597 writeq(val64, &bar0->rts_qos_steering);
1600 val64 = 0x0001000102000001ULL;
1601 writeq(val64, &bar0->rx_w_round_robin_0);
1602 val64 = 0x0001020000010001ULL;
1603 writeq(val64, &bar0->rx_w_round_robin_1);
1604 val64 = 0x0200000100010200ULL;
1605 writeq(val64, &bar0->rx_w_round_robin_2);
1606 val64 = 0x0001000102000001ULL;
1607 writeq(val64, &bar0->rx_w_round_robin_3);
1608 val64 = 0x0001020000000000ULL;
1609 writeq(val64, &bar0->rx_w_round_robin_4);
1611 val64 = 0x8080804040402020ULL;
1612 writeq(val64, &bar0->rts_qos_steering);
1615 val64 = 0x0001020300010200ULL;
1616 writeq(val64, &bar0->rx_w_round_robin_0);
1617 val64 = 0x0100000102030001ULL;
1618 writeq(val64, &bar0->rx_w_round_robin_1);
1619 val64 = 0x0200010000010203ULL;
1620 writeq(val64, &bar0->rx_w_round_robin_2);
1621 val64 = 0x0001020001000001ULL;
1622 writeq(val64, &bar0->rx_w_round_robin_3);
1623 val64 = 0x0203000100000000ULL;
1624 writeq(val64, &bar0->rx_w_round_robin_4);
1626 val64 = 0x8080404020201010ULL;
1627 writeq(val64, &bar0->rts_qos_steering);
1630 val64 = 0x0001000203000102ULL;
1631 writeq(val64, &bar0->rx_w_round_robin_0);
1632 val64 = 0x0001020001030004ULL;
1633 writeq(val64, &bar0->rx_w_round_robin_1);
1634 val64 = 0x0001000203000102ULL;
1635 writeq(val64, &bar0->rx_w_round_robin_2);
1636 val64 = 0x0001020001030004ULL;
1637 writeq(val64, &bar0->rx_w_round_robin_3);
1638 val64 = 0x0001000000000000ULL;
1639 writeq(val64, &bar0->rx_w_round_robin_4);
1641 val64 = 0x8080404020201008ULL;
1642 writeq(val64, &bar0->rts_qos_steering);
1645 val64 = 0x0001020304000102ULL;
1646 writeq(val64, &bar0->rx_w_round_robin_0);
1647 val64 = 0x0304050001020001ULL;
1648 writeq(val64, &bar0->rx_w_round_robin_1);
1649 val64 = 0x0203000100000102ULL;
1650 writeq(val64, &bar0->rx_w_round_robin_2);
1651 val64 = 0x0304000102030405ULL;
1652 writeq(val64, &bar0->rx_w_round_robin_3);
1653 val64 = 0x0001000200000000ULL;
1654 writeq(val64, &bar0->rx_w_round_robin_4);
1656 val64 = 0x8080404020100804ULL;
1657 writeq(val64, &bar0->rts_qos_steering);
1660 val64 = 0x0001020001020300ULL;
1661 writeq(val64, &bar0->rx_w_round_robin_0);
1662 val64 = 0x0102030400010203ULL;
1663 writeq(val64, &bar0->rx_w_round_robin_1);
1664 val64 = 0x0405060001020001ULL;
1665 writeq(val64, &bar0->rx_w_round_robin_2);
1666 val64 = 0x0304050000010200ULL;
1667 writeq(val64, &bar0->rx_w_round_robin_3);
1668 val64 = 0x0102030000000000ULL;
1669 writeq(val64, &bar0->rx_w_round_robin_4);
1671 val64 = 0x8080402010080402ULL;
1672 writeq(val64, &bar0->rts_qos_steering);
1675 val64 = 0x0001020300040105ULL;
1676 writeq(val64, &bar0->rx_w_round_robin_0);
1677 val64 = 0x0200030106000204ULL;
1678 writeq(val64, &bar0->rx_w_round_robin_1);
1679 val64 = 0x0103000502010007ULL;
1680 writeq(val64, &bar0->rx_w_round_robin_2);
1681 val64 = 0x0304010002060500ULL;
1682 writeq(val64, &bar0->rx_w_round_robin_3);
1683 val64 = 0x0103020400000000ULL;
1684 writeq(val64, &bar0->rx_w_round_robin_4);
1686 val64 = 0x8040201008040201ULL;
1687 writeq(val64, &bar0->rts_qos_steering);
1693 for (i = 0; i < 8; i++)
1694 writeq(val64, &bar0->rts_frm_len_n[i]);
1696 /* Set the default rts frame length for the rings configured */
1697 val64 = MAC_RTS_FRM_LEN_SET(dev->mtu+22);
1698 for (i = 0 ; i < config->rx_ring_num ; i++)
1699 writeq(val64, &bar0->rts_frm_len_n[i]);
1701 /* Set the frame length for the configured rings
1702 * desired by the user
1704 for (i = 0; i < config->rx_ring_num; i++) {
1705 /* If rts_frm_len[i] == 0 then it is assumed that user not
1706 * specified frame length steering.
1707 * If the user provides the frame length then program
1708 * the rts_frm_len register for those values or else
1709 * leave it as it is.
1711 if (rts_frm_len[i] != 0) {
1712 writeq(MAC_RTS_FRM_LEN_SET(rts_frm_len[i]),
1713 &bar0->rts_frm_len_n[i]);
1717 /* Disable differentiated services steering logic */
1718 for (i = 0; i < 64; i++) {
1719 if (rts_ds_steer(nic, i, 0) == FAILURE) {
1720 DBG_PRINT(ERR_DBG, "%s: failed rts ds steering",
1722 DBG_PRINT(ERR_DBG, "set on codepoint %d\n", i);
1727 /* Program statistics memory */
1728 writeq(mac_control->stats_mem_phy, &bar0->stat_addr);
1730 if (nic->device_type == XFRAME_II_DEVICE) {
1731 val64 = STAT_BC(0x320);
1732 writeq(val64, &bar0->stat_byte_cnt);
1736 * Initializing the sampling rate for the device to calculate the
1737 * bandwidth utilization.
1739 val64 = MAC_TX_LINK_UTIL_VAL(tmac_util_period) |
1740 MAC_RX_LINK_UTIL_VAL(rmac_util_period);
1741 writeq(val64, &bar0->mac_link_util);
1744 * Initializing the Transmit and Receive Traffic Interrupt
1748 /* Initialize TTI */
1749 if (SUCCESS != init_tti(nic, nic->last_link_state))
1752 /* RTI Initialization */
1753 if (nic->device_type == XFRAME_II_DEVICE) {
1755 * Programmed to generate Apprx 500 Intrs per
1758 int count = (nic->config.bus_speed * 125)/4;
1759 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count);
1761 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF);
1762 val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) |
1763 RTI_DATA1_MEM_RX_URNG_B(0x10) |
1764 RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN;
1766 writeq(val64, &bar0->rti_data1_mem);
1768 val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) |
1769 RTI_DATA2_MEM_RX_UFC_B(0x2) ;
1770 if (nic->config.intr_type == MSI_X)
1771 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x20) | \
1772 RTI_DATA2_MEM_RX_UFC_D(0x40));
1774 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x40) | \
1775 RTI_DATA2_MEM_RX_UFC_D(0x80));
1776 writeq(val64, &bar0->rti_data2_mem);
1778 for (i = 0; i < config->rx_ring_num; i++) {
1779 val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD
1780 | RTI_CMD_MEM_OFFSET(i);
1781 writeq(val64, &bar0->rti_command_mem);
1784 * Once the operation completes, the Strobe bit of the
1785 * command register will be reset. We poll for this
1786 * particular condition. We wait for a maximum of 500ms
1787 * for the operation to complete, if it's not complete
1788 * by then we return error.
1792 val64 = readq(&bar0->rti_command_mem);
1793 if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD))
1797 DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n",
1807 * Initializing proper values as Pause threshold into all
1808 * the 8 Queues on Rx side.
1810 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q0q3);
1811 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7);
1813 /* Disable RMAC PAD STRIPPING */
1814 add = &bar0->mac_cfg;
1815 val64 = readq(&bar0->mac_cfg);
1816 val64 &= ~(MAC_CFG_RMAC_STRIP_PAD);
1817 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1818 writel((u32) (val64), add);
1819 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1820 writel((u32) (val64 >> 32), (add + 4));
1821 val64 = readq(&bar0->mac_cfg);
1823 /* Enable FCS stripping by adapter */
1824 add = &bar0->mac_cfg;
1825 val64 = readq(&bar0->mac_cfg);
1826 val64 |= MAC_CFG_RMAC_STRIP_FCS;
1827 if (nic->device_type == XFRAME_II_DEVICE)
1828 writeq(val64, &bar0->mac_cfg);
1830 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1831 writel((u32) (val64), add);
1832 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1833 writel((u32) (val64 >> 32), (add + 4));
1837 * Set the time value to be inserted in the pause frame
1838 * generated by xena.
1840 val64 = readq(&bar0->rmac_pause_cfg);
1841 val64 &= ~(RMAC_PAUSE_HG_PTIME(0xffff));
1842 val64 |= RMAC_PAUSE_HG_PTIME(nic->mac_control.rmac_pause_time);
1843 writeq(val64, &bar0->rmac_pause_cfg);
1846 * Set the Threshold Limit for Generating the pause frame
1847 * If the amount of data in any Queue exceeds ratio of
1848 * (mac_control.mc_pause_threshold_q0q3 or q4q7)/256
1849 * pause frame is generated
1852 for (i = 0; i < 4; i++) {
1854 (((u64) 0xFF00 | nic->mac_control.
1855 mc_pause_threshold_q0q3)
1858 writeq(val64, &bar0->mc_pause_thresh_q0q3);
1861 for (i = 0; i < 4; i++) {
1863 (((u64) 0xFF00 | nic->mac_control.
1864 mc_pause_threshold_q4q7)
1867 writeq(val64, &bar0->mc_pause_thresh_q4q7);
1870 * TxDMA will stop Read request if the number of read split has
1871 * exceeded the limit pointed by shared_splits
1873 val64 = readq(&bar0->pic_control);
1874 val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits);
1875 writeq(val64, &bar0->pic_control);
1877 if (nic->config.bus_speed == 266) {
1878 writeq(TXREQTO_VAL(0x7f) | TXREQTO_EN, &bar0->txreqtimeout);
1879 writeq(0x0, &bar0->read_retry_delay);
1880 writeq(0x0, &bar0->write_retry_delay);
1884 * Programming the Herc to split every write transaction
1885 * that does not start on an ADB to reduce disconnects.
1887 if (nic->device_type == XFRAME_II_DEVICE) {
1888 val64 = FAULT_BEHAVIOUR | EXT_REQ_EN |
1889 MISC_LINK_STABILITY_PRD(3);
1890 writeq(val64, &bar0->misc_control);
1891 val64 = readq(&bar0->pic_control2);
1892 val64 &= ~(s2BIT(13)|s2BIT(14)|s2BIT(15));
1893 writeq(val64, &bar0->pic_control2);
1895 if (strstr(nic->product_name, "CX4")) {
1896 val64 = TMAC_AVG_IPG(0x17);
1897 writeq(val64, &bar0->tmac_avg_ipg);
1902 #define LINK_UP_DOWN_INTERRUPT 1
1903 #define MAC_RMAC_ERR_TIMER 2
1905 static int s2io_link_fault_indication(struct s2io_nic *nic)
1907 if (nic->config.intr_type != INTA)
1908 return MAC_RMAC_ERR_TIMER;
1909 if (nic->device_type == XFRAME_II_DEVICE)
1910 return LINK_UP_DOWN_INTERRUPT;
1912 return MAC_RMAC_ERR_TIMER;
1916 * do_s2io_write_bits - update alarm bits in alarm register
1917 * @value: alarm bits
1918 * @flag: interrupt status
1919 * @addr: address value
1920 * Description: update alarm bits in alarm register
1924 static void do_s2io_write_bits(u64 value, int flag, void __iomem *addr)
1928 temp64 = readq(addr);
1930 if(flag == ENABLE_INTRS)
1931 temp64 &= ~((u64) value);
1933 temp64 |= ((u64) value);
1934 writeq(temp64, addr);
1937 static void en_dis_err_alarms(struct s2io_nic *nic, u16 mask, int flag)
1939 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1940 register u64 gen_int_mask = 0;
1942 if (mask & TX_DMA_INTR) {
1944 gen_int_mask |= TXDMA_INT_M;
1946 do_s2io_write_bits(TXDMA_TDA_INT | TXDMA_PFC_INT |
1947 TXDMA_PCC_INT | TXDMA_TTI_INT |
1948 TXDMA_LSO_INT | TXDMA_TPA_INT |
1949 TXDMA_SM_INT, flag, &bar0->txdma_int_mask);
1951 do_s2io_write_bits(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM |
1952 PFC_MISC_0_ERR | PFC_MISC_1_ERR |
1953 PFC_PCIX_ERR | PFC_ECC_SG_ERR, flag,
1954 &bar0->pfc_err_mask);
1956 do_s2io_write_bits(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
1957 TDA_SM1_ERR_ALARM | TDA_Fn_ECC_SG_ERR |
1958 TDA_PCIX_ERR, flag, &bar0->tda_err_mask);
1960 do_s2io_write_bits(PCC_FB_ECC_DB_ERR | PCC_TXB_ECC_DB_ERR |
1961 PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM |
1962 PCC_N_SERR | PCC_6_COF_OV_ERR |
1963 PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR |
1964 PCC_7_LSO_OV_ERR | PCC_FB_ECC_SG_ERR |
1965 PCC_TXB_ECC_SG_ERR, flag, &bar0->pcc_err_mask);
1967 do_s2io_write_bits(TTI_SM_ERR_ALARM | TTI_ECC_SG_ERR |
1968 TTI_ECC_DB_ERR, flag, &bar0->tti_err_mask);
1970 do_s2io_write_bits(LSO6_ABORT | LSO7_ABORT |
1971 LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM |
1972 LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
1973 flag, &bar0->lso_err_mask);
1975 do_s2io_write_bits(TPA_SM_ERR_ALARM | TPA_TX_FRM_DROP,
1976 flag, &bar0->tpa_err_mask);
1978 do_s2io_write_bits(SM_SM_ERR_ALARM, flag, &bar0->sm_err_mask);
1982 if (mask & TX_MAC_INTR) {
1983 gen_int_mask |= TXMAC_INT_M;
1984 do_s2io_write_bits(MAC_INT_STATUS_TMAC_INT, flag,
1985 &bar0->mac_int_mask);
1986 do_s2io_write_bits(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR |
1987 TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR |
1988 TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
1989 flag, &bar0->mac_tmac_err_mask);
1992 if (mask & TX_XGXS_INTR) {
1993 gen_int_mask |= TXXGXS_INT_M;
1994 do_s2io_write_bits(XGXS_INT_STATUS_TXGXS, flag,
1995 &bar0->xgxs_int_mask);
1996 do_s2io_write_bits(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR |
1997 TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
1998 flag, &bar0->xgxs_txgxs_err_mask);
2001 if (mask & RX_DMA_INTR) {
2002 gen_int_mask |= RXDMA_INT_M;
2003 do_s2io_write_bits(RXDMA_INT_RC_INT_M | RXDMA_INT_RPA_INT_M |
2004 RXDMA_INT_RDA_INT_M | RXDMA_INT_RTI_INT_M,
2005 flag, &bar0->rxdma_int_mask);
2006 do_s2io_write_bits(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR |
2007 RC_PRCn_SM_ERR_ALARM | RC_FTC_SM_ERR_ALARM |
2008 RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR |
2009 RC_RDA_FAIL_WR_Rn, flag, &bar0->rc_err_mask);
2010 do_s2io_write_bits(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn |
2011 PRC_PCI_AB_F_WR_Rn | PRC_PCI_DP_RD_Rn |
2012 PRC_PCI_DP_WR_Rn | PRC_PCI_DP_F_WR_Rn, flag,
2013 &bar0->prc_pcix_err_mask);
2014 do_s2io_write_bits(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR |
2015 RPA_ECC_SG_ERR | RPA_ECC_DB_ERR, flag,
2016 &bar0->rpa_err_mask);
2017 do_s2io_write_bits(RDA_RXDn_ECC_DB_ERR | RDA_FRM_ECC_DB_N_AERR |
2018 RDA_SM1_ERR_ALARM | RDA_SM0_ERR_ALARM |
2019 RDA_RXD_ECC_DB_SERR | RDA_RXDn_ECC_SG_ERR |
2020 RDA_FRM_ECC_SG_ERR | RDA_MISC_ERR|RDA_PCIX_ERR,
2021 flag, &bar0->rda_err_mask);
2022 do_s2io_write_bits(RTI_SM_ERR_ALARM |
2023 RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
2024 flag, &bar0->rti_err_mask);
2027 if (mask & RX_MAC_INTR) {
2028 gen_int_mask |= RXMAC_INT_M;
2029 do_s2io_write_bits(MAC_INT_STATUS_RMAC_INT, flag,
2030 &bar0->mac_int_mask);
2031 do_s2io_write_bits(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR |
2032 RMAC_UNUSED_INT | RMAC_SINGLE_ECC_ERR |
2033 RMAC_DOUBLE_ECC_ERR |
2034 RMAC_LINK_STATE_CHANGE_INT,
2035 flag, &bar0->mac_rmac_err_mask);
2038 if (mask & RX_XGXS_INTR)
2040 gen_int_mask |= RXXGXS_INT_M;
2041 do_s2io_write_bits(XGXS_INT_STATUS_RXGXS, flag,
2042 &bar0->xgxs_int_mask);
2043 do_s2io_write_bits(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR, flag,
2044 &bar0->xgxs_rxgxs_err_mask);
2047 if (mask & MC_INTR) {
2048 gen_int_mask |= MC_INT_M;
2049 do_s2io_write_bits(MC_INT_MASK_MC_INT, flag, &bar0->mc_int_mask);
2050 do_s2io_write_bits(MC_ERR_REG_SM_ERR | MC_ERR_REG_ECC_ALL_SNG |
2051 MC_ERR_REG_ECC_ALL_DBL | PLL_LOCK_N, flag,
2052 &bar0->mc_err_mask);
2054 nic->general_int_mask = gen_int_mask;
2056 /* Remove this line when alarm interrupts are enabled */
2057 nic->general_int_mask = 0;
2060 * en_dis_able_nic_intrs - Enable or Disable the interrupts
2061 * @nic: device private variable,
2062 * @mask: A mask indicating which Intr block must be modified and,
2063 * @flag: A flag indicating whether to enable or disable the Intrs.
2064 * Description: This function will either disable or enable the interrupts
2065 * depending on the flag argument. The mask argument can be used to
2066 * enable/disable any Intr block.
2067 * Return Value: NONE.
2070 static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag)
2072 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2073 register u64 temp64 = 0, intr_mask = 0;
2075 intr_mask = nic->general_int_mask;
2077 /* Top level interrupt classification */
2078 /* PIC Interrupts */
2079 if (mask & TX_PIC_INTR) {
2080 /* Enable PIC Intrs in the general intr mask register */
2081 intr_mask |= TXPIC_INT_M;
2082 if (flag == ENABLE_INTRS) {
2084 * If Hercules adapter enable GPIO otherwise
2085 * disable all PCIX, Flash, MDIO, IIC and GPIO
2086 * interrupts for now.
2089 if (s2io_link_fault_indication(nic) ==
2090 LINK_UP_DOWN_INTERRUPT ) {
2091 do_s2io_write_bits(PIC_INT_GPIO, flag,
2092 &bar0->pic_int_mask);
2093 do_s2io_write_bits(GPIO_INT_MASK_LINK_UP, flag,
2094 &bar0->gpio_int_mask);
2096 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
2097 } else if (flag == DISABLE_INTRS) {
2099 * Disable PIC Intrs in the general
2100 * intr mask register
2102 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
2106 /* Tx traffic interrupts */
2107 if (mask & TX_TRAFFIC_INTR) {
2108 intr_mask |= TXTRAFFIC_INT_M;
2109 if (flag == ENABLE_INTRS) {
2111 * Enable all the Tx side interrupts
2112 * writing 0 Enables all 64 TX interrupt levels
2114 writeq(0x0, &bar0->tx_traffic_mask);
2115 } else if (flag == DISABLE_INTRS) {
2117 * Disable Tx Traffic Intrs in the general intr mask
2120 writeq(DISABLE_ALL_INTRS, &bar0->tx_traffic_mask);
2124 /* Rx traffic interrupts */
2125 if (mask & RX_TRAFFIC_INTR) {
2126 intr_mask |= RXTRAFFIC_INT_M;
2127 if (flag == ENABLE_INTRS) {
2128 /* writing 0 Enables all 8 RX interrupt levels */
2129 writeq(0x0, &bar0->rx_traffic_mask);
2130 } else if (flag == DISABLE_INTRS) {
2132 * Disable Rx Traffic Intrs in the general intr mask
2135 writeq(DISABLE_ALL_INTRS, &bar0->rx_traffic_mask);
2139 temp64 = readq(&bar0->general_int_mask);
2140 if (flag == ENABLE_INTRS)
2141 temp64 &= ~((u64) intr_mask);
2143 temp64 = DISABLE_ALL_INTRS;
2144 writeq(temp64, &bar0->general_int_mask);
2146 nic->general_int_mask = readq(&bar0->general_int_mask);
2150 * verify_pcc_quiescent- Checks for PCC quiescent state
2151 * Return: 1 If PCC is quiescence
2152 * 0 If PCC is not quiescence
2154 static int verify_pcc_quiescent(struct s2io_nic *sp, int flag)
2157 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2158 u64 val64 = readq(&bar0->adapter_status);
2160 herc = (sp->device_type == XFRAME_II_DEVICE);
2162 if (flag == FALSE) {
2163 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
2164 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE))
2167 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2171 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
2172 if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
2173 ADAPTER_STATUS_RMAC_PCC_IDLE))
2176 if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) ==
2177 ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2185 * verify_xena_quiescence - Checks whether the H/W is ready
2186 * Description: Returns whether the H/W is ready to go or not. Depending
2187 * on whether adapter enable bit was written or not the comparison
2188 * differs and the calling function passes the input argument flag to
2190 * Return: 1 If xena is quiescence
2191 * 0 If Xena is not quiescence
2194 static int verify_xena_quiescence(struct s2io_nic *sp)
2197 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2198 u64 val64 = readq(&bar0->adapter_status);
2199 mode = s2io_verify_pci_mode(sp);
2201 if (!(val64 & ADAPTER_STATUS_TDMA_READY)) {
2202 DBG_PRINT(ERR_DBG, "%s", "TDMA is not ready!");
2205 if (!(val64 & ADAPTER_STATUS_RDMA_READY)) {
2206 DBG_PRINT(ERR_DBG, "%s", "RDMA is not ready!");
2209 if (!(val64 & ADAPTER_STATUS_PFC_READY)) {
2210 DBG_PRINT(ERR_DBG, "%s", "PFC is not ready!");
2213 if (!(val64 & ADAPTER_STATUS_TMAC_BUF_EMPTY)) {
2214 DBG_PRINT(ERR_DBG, "%s", "TMAC BUF is not empty!");
2217 if (!(val64 & ADAPTER_STATUS_PIC_QUIESCENT)) {
2218 DBG_PRINT(ERR_DBG, "%s", "PIC is not QUIESCENT!");
2221 if (!(val64 & ADAPTER_STATUS_MC_DRAM_READY)) {
2222 DBG_PRINT(ERR_DBG, "%s", "MC_DRAM is not ready!");
2225 if (!(val64 & ADAPTER_STATUS_MC_QUEUES_READY)) {
2226 DBG_PRINT(ERR_DBG, "%s", "MC_QUEUES is not ready!");
2229 if (!(val64 & ADAPTER_STATUS_M_PLL_LOCK)) {
2230 DBG_PRINT(ERR_DBG, "%s", "M_PLL is not locked!");
2235 * In PCI 33 mode, the P_PLL is not used, and therefore,
2236 * the the P_PLL_LOCK bit in the adapter_status register will
2239 if (!(val64 & ADAPTER_STATUS_P_PLL_LOCK) &&
2240 sp->device_type == XFRAME_II_DEVICE && mode !=
2242 DBG_PRINT(ERR_DBG, "%s", "P_PLL is not locked!");
2245 if (!((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
2246 ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
2247 DBG_PRINT(ERR_DBG, "%s", "RC_PRC is not QUIESCENT!");
2254 * fix_mac_address - Fix for Mac addr problem on Alpha platforms
2255 * @sp: Pointer to device specifc structure
2257 * New procedure to clear mac address reading problems on Alpha platforms
2261 static void fix_mac_address(struct s2io_nic * sp)
2263 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2267 while (fix_mac[i] != END_SIGN) {
2268 writeq(fix_mac[i++], &bar0->gpio_control);
2270 val64 = readq(&bar0->gpio_control);
2275 * start_nic - Turns the device on
2276 * @nic : device private variable.
2278 * This function actually turns the device on. Before this function is
2279 * called,all Registers are configured from their reset states
2280 * and shared memory is allocated but the NIC is still quiescent. On
2281 * calling this function, the device interrupts are cleared and the NIC is
2282 * literally switched on by writing into the adapter control register.
2284 * SUCCESS on success and -1 on failure.
2287 static int start_nic(struct s2io_nic *nic)
2289 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2290 struct net_device *dev = nic->dev;
2291 register u64 val64 = 0;
2293 struct mac_info *mac_control;
2294 struct config_param *config;
2296 mac_control = &nic->mac_control;
2297 config = &nic->config;
2299 /* PRC Initialization and configuration */
2300 for (i = 0; i < config->rx_ring_num; i++) {
2301 writeq((u64) mac_control->rings[i].rx_blocks[0].block_dma_addr,
2302 &bar0->prc_rxd0_n[i]);
2304 val64 = readq(&bar0->prc_ctrl_n[i]);
2305 if (nic->rxd_mode == RXD_MODE_1)
2306 val64 |= PRC_CTRL_RC_ENABLED;
2308 val64 |= PRC_CTRL_RC_ENABLED | PRC_CTRL_RING_MODE_3;
2309 if (nic->device_type == XFRAME_II_DEVICE)
2310 val64 |= PRC_CTRL_GROUP_READS;
2311 val64 &= ~PRC_CTRL_RXD_BACKOFF_INTERVAL(0xFFFFFF);
2312 val64 |= PRC_CTRL_RXD_BACKOFF_INTERVAL(0x1000);
2313 writeq(val64, &bar0->prc_ctrl_n[i]);
2316 if (nic->rxd_mode == RXD_MODE_3B) {
2317 /* Enabling 2 buffer mode by writing into Rx_pa_cfg reg. */
2318 val64 = readq(&bar0->rx_pa_cfg);
2319 val64 |= RX_PA_CFG_IGNORE_L2_ERR;
2320 writeq(val64, &bar0->rx_pa_cfg);
2323 if (vlan_tag_strip == 0) {
2324 val64 = readq(&bar0->rx_pa_cfg);
2325 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
2326 writeq(val64, &bar0->rx_pa_cfg);
2327 vlan_strip_flag = 0;
2331 * Enabling MC-RLDRAM. After enabling the device, we timeout
2332 * for around 100ms, which is approximately the time required
2333 * for the device to be ready for operation.
2335 val64 = readq(&bar0->mc_rldram_mrs);
2336 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE | MC_RLDRAM_MRS_ENABLE;
2337 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
2338 val64 = readq(&bar0->mc_rldram_mrs);
2340 msleep(100); /* Delay by around 100 ms. */
2342 /* Enabling ECC Protection. */
2343 val64 = readq(&bar0->adapter_control);
2344 val64 &= ~ADAPTER_ECC_EN;
2345 writeq(val64, &bar0->adapter_control);
2348 * Verify if the device is ready to be enabled, if so enable
2351 val64 = readq(&bar0->adapter_status);
2352 if (!verify_xena_quiescence(nic)) {
2353 DBG_PRINT(ERR_DBG, "%s: device is not ready, ", dev->name);
2354 DBG_PRINT(ERR_DBG, "Adapter status reads: 0x%llx\n",
2355 (unsigned long long) val64);
2360 * With some switches, link might be already up at this point.
2361 * Because of this weird behavior, when we enable laser,
2362 * we may not get link. We need to handle this. We cannot
2363 * figure out which switch is misbehaving. So we are forced to
2364 * make a global change.
2367 /* Enabling Laser. */
2368 val64 = readq(&bar0->adapter_control);
2369 val64 |= ADAPTER_EOI_TX_ON;
2370 writeq(val64, &bar0->adapter_control);
2372 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
2374 * Dont see link state interrupts initally on some switches,
2375 * so directly scheduling the link state task here.
2377 schedule_work(&nic->set_link_task);
2379 /* SXE-002: Initialize link and activity LED */
2380 subid = nic->pdev->subsystem_device;
2381 if (((subid & 0xFF) >= 0x07) &&
2382 (nic->device_type == XFRAME_I_DEVICE)) {
2383 val64 = readq(&bar0->gpio_control);
2384 val64 |= 0x0000800000000000ULL;
2385 writeq(val64, &bar0->gpio_control);
2386 val64 = 0x0411040400000000ULL;
2387 writeq(val64, (void __iomem *)bar0 + 0x2700);
2393 * s2io_txdl_getskb - Get the skb from txdl, unmap and return skb
2395 static struct sk_buff *s2io_txdl_getskb(struct fifo_info *fifo_data, struct \
2396 TxD *txdlp, int get_off)
2398 struct s2io_nic *nic = fifo_data->nic;
2399 struct sk_buff *skb;
2404 if (txds->Host_Control == (u64)(long)fifo_data->ufo_in_band_v) {
2405 pci_unmap_single(nic->pdev, (dma_addr_t)
2406 txds->Buffer_Pointer, sizeof(u64),
2411 skb = (struct sk_buff *) ((unsigned long)
2412 txds->Host_Control);
2414 memset(txdlp, 0, (sizeof(struct TxD) * fifo_data->max_txds));
2417 pci_unmap_single(nic->pdev, (dma_addr_t)
2418 txds->Buffer_Pointer,
2419 skb->len - skb->data_len,
2421 frg_cnt = skb_shinfo(skb)->nr_frags;
2424 for (j = 0; j < frg_cnt; j++, txds++) {
2425 skb_frag_t *frag = &skb_shinfo(skb)->frags[j];
2426 if (!txds->Buffer_Pointer)
2428 pci_unmap_page(nic->pdev, (dma_addr_t)
2429 txds->Buffer_Pointer,
2430 frag->size, PCI_DMA_TODEVICE);
2433 memset(txdlp,0, (sizeof(struct TxD) * fifo_data->max_txds));
2438 * free_tx_buffers - Free all queued Tx buffers
2439 * @nic : device private variable.
2441 * Free all queued Tx buffers.
2442 * Return Value: void
2445 static void free_tx_buffers(struct s2io_nic *nic)
2447 struct net_device *dev = nic->dev;
2448 struct sk_buff *skb;
2451 struct mac_info *mac_control;
2452 struct config_param *config;
2455 mac_control = &nic->mac_control;
2456 config = &nic->config;
2458 for (i = 0; i < config->tx_fifo_num; i++) {
2459 unsigned long flags;
2460 spin_lock_irqsave(&mac_control->fifos[i].tx_lock, flags);
2461 for (j = 0; j < config->tx_cfg[i].fifo_len - 1; j++) {
2462 txdp = (struct TxD *) \
2463 mac_control->fifos[i].list_info[j].list_virt_addr;
2464 skb = s2io_txdl_getskb(&mac_control->fifos[i], txdp, j);
2466 nic->mac_control.stats_info->sw_stat.mem_freed
2473 "%s:forcibly freeing %d skbs on FIFO%d\n",
2475 mac_control->fifos[i].tx_curr_get_info.offset = 0;
2476 mac_control->fifos[i].tx_curr_put_info.offset = 0;
2477 spin_unlock_irqrestore(&mac_control->fifos[i].tx_lock, flags);
2482 * stop_nic - To stop the nic
2483 * @nic ; device private variable.
2485 * This function does exactly the opposite of what the start_nic()
2486 * function does. This function is called to stop the device.
2491 static void stop_nic(struct s2io_nic *nic)
2493 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2494 register u64 val64 = 0;
2496 struct mac_info *mac_control;
2497 struct config_param *config;
2499 mac_control = &nic->mac_control;
2500 config = &nic->config;
2502 /* Disable all interrupts */
2503 en_dis_err_alarms(nic, ENA_ALL_INTRS, DISABLE_INTRS);
2504 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
2505 interruptible |= TX_PIC_INTR;
2506 en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS);
2508 /* Clearing Adapter_En bit of ADAPTER_CONTROL Register */
2509 val64 = readq(&bar0->adapter_control);
2510 val64 &= ~(ADAPTER_CNTL_EN);
2511 writeq(val64, &bar0->adapter_control);
2515 * fill_rx_buffers - Allocates the Rx side skbs
2516 * @nic: device private variable
2517 * @ring_no: ring number
2519 * The function allocates Rx side skbs and puts the physical
2520 * address of these buffers into the RxD buffer pointers, so that the NIC
2521 * can DMA the received frame into these locations.
2522 * The NIC supports 3 receive modes, viz
2524 * 2. three buffer and
2525 * 3. Five buffer modes.
2526 * Each mode defines how many fragments the received frame will be split
2527 * up into by the NIC. The frame is split into L3 header, L4 Header,
2528 * L4 payload in three buffer mode and in 5 buffer mode, L4 payload itself
2529 * is split into 3 fragments. As of now only single buffer mode is
2532 * SUCCESS on success or an appropriate -ve value on failure.
2535 static int fill_rx_buffers(struct s2io_nic *nic, int ring_no)
2537 struct net_device *dev = nic->dev;
2538 struct sk_buff *skb;
2540 int off, off1, size, block_no, block_no1;
2543 struct mac_info *mac_control;
2544 struct config_param *config;
2547 unsigned long flags;
2548 struct RxD_t *first_rxdp = NULL;
2549 u64 Buffer0_ptr = 0, Buffer1_ptr = 0;
2552 struct swStat *stats = &nic->mac_control.stats_info->sw_stat;
2554 mac_control = &nic->mac_control;
2555 config = &nic->config;
2556 alloc_cnt = mac_control->rings[ring_no].pkt_cnt -
2557 atomic_read(&nic->rx_bufs_left[ring_no]);
2559 block_no1 = mac_control->rings[ring_no].rx_curr_get_info.block_index;
2560 off1 = mac_control->rings[ring_no].rx_curr_get_info.offset;
2561 while (alloc_tab < alloc_cnt) {
2562 block_no = mac_control->rings[ring_no].rx_curr_put_info.
2564 off = mac_control->rings[ring_no].rx_curr_put_info.offset;
2566 rxdp = mac_control->rings[ring_no].
2567 rx_blocks[block_no].rxds[off].virt_addr;
2569 if ((block_no == block_no1) && (off == off1) &&
2570 (rxdp->Host_Control)) {
2571 DBG_PRINT(INTR_DBG, "%s: Get and Put",
2573 DBG_PRINT(INTR_DBG, " info equated\n");
2576 if (off && (off == rxd_count[nic->rxd_mode])) {
2577 mac_control->rings[ring_no].rx_curr_put_info.
2579 if (mac_control->rings[ring_no].rx_curr_put_info.
2580 block_index == mac_control->rings[ring_no].
2582 mac_control->rings[ring_no].rx_curr_put_info.
2584 block_no = mac_control->rings[ring_no].
2585 rx_curr_put_info.block_index;
2586 if (off == rxd_count[nic->rxd_mode])
2588 mac_control->rings[ring_no].rx_curr_put_info.
2590 rxdp = mac_control->rings[ring_no].
2591 rx_blocks[block_no].block_virt_addr;
2592 DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n",
2596 spin_lock_irqsave(&nic->put_lock, flags);
2597 mac_control->rings[ring_no].put_pos =
2598 (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
2599 spin_unlock_irqrestore(&nic->put_lock, flags);
2601 mac_control->rings[ring_no].put_pos =
2602 (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
2604 if ((rxdp->Control_1 & RXD_OWN_XENA) &&
2605 ((nic->rxd_mode == RXD_MODE_3B) &&
2606 (rxdp->Control_2 & s2BIT(0)))) {
2607 mac_control->rings[ring_no].rx_curr_put_info.
2611 /* calculate size of skb based on ring mode */
2612 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
2613 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
2614 if (nic->rxd_mode == RXD_MODE_1)
2615 size += NET_IP_ALIGN;
2617 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
2620 skb = dev_alloc_skb(size);
2622 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
2623 DBG_PRINT(INFO_DBG, "memory to allocate SKBs\n");
2626 first_rxdp->Control_1 |= RXD_OWN_XENA;
2628 nic->mac_control.stats_info->sw_stat. \
2629 mem_alloc_fail_cnt++;
2632 nic->mac_control.stats_info->sw_stat.mem_allocated
2634 if (nic->rxd_mode == RXD_MODE_1) {
2635 /* 1 buffer mode - normal operation mode */
2636 rxdp1 = (struct RxD1*)rxdp;
2637 memset(rxdp, 0, sizeof(struct RxD1));
2638 skb_reserve(skb, NET_IP_ALIGN);
2639 rxdp1->Buffer0_ptr = pci_map_single
2640 (nic->pdev, skb->data, size - NET_IP_ALIGN,
2641 PCI_DMA_FROMDEVICE);
2642 if( (rxdp1->Buffer0_ptr == 0) ||
2643 (rxdp1->Buffer0_ptr ==
2645 goto pci_map_failed;
2648 SET_BUFFER0_SIZE_1(size - NET_IP_ALIGN);
2650 } else if (nic->rxd_mode == RXD_MODE_3B) {
2653 * 2 buffer mode provides 128
2654 * byte aligned receive buffers.
2657 rxdp3 = (struct RxD3*)rxdp;
2658 /* save buffer pointers to avoid frequent dma mapping */
2659 Buffer0_ptr = rxdp3->Buffer0_ptr;
2660 Buffer1_ptr = rxdp3->Buffer1_ptr;
2661 memset(rxdp, 0, sizeof(struct RxD3));
2662 /* restore the buffer pointers for dma sync*/
2663 rxdp3->Buffer0_ptr = Buffer0_ptr;
2664 rxdp3->Buffer1_ptr = Buffer1_ptr;
2666 ba = &mac_control->rings[ring_no].ba[block_no][off];
2667 skb_reserve(skb, BUF0_LEN);
2668 tmp = (u64)(unsigned long) skb->data;
2671 skb->data = (void *) (unsigned long)tmp;
2672 skb_reset_tail_pointer(skb);
2674 if (!(rxdp3->Buffer0_ptr))
2675 rxdp3->Buffer0_ptr =
2676 pci_map_single(nic->pdev, ba->ba_0, BUF0_LEN,
2677 PCI_DMA_FROMDEVICE);
2679 pci_dma_sync_single_for_device(nic->pdev,
2680 (dma_addr_t) rxdp3->Buffer0_ptr,
2681 BUF0_LEN, PCI_DMA_FROMDEVICE);
2682 if( (rxdp3->Buffer0_ptr == 0) ||
2683 (rxdp3->Buffer0_ptr == DMA_ERROR_CODE))
2684 goto pci_map_failed;
2686 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
2687 if (nic->rxd_mode == RXD_MODE_3B) {
2688 /* Two buffer mode */
2691 * Buffer2 will have L3/L4 header plus
2694 rxdp3->Buffer2_ptr = pci_map_single
2695 (nic->pdev, skb->data, dev->mtu + 4,
2696 PCI_DMA_FROMDEVICE);
2698 if( (rxdp3->Buffer2_ptr == 0) ||
2699 (rxdp3->Buffer2_ptr == DMA_ERROR_CODE))
2700 goto pci_map_failed;
2702 rxdp3->Buffer1_ptr =
2703 pci_map_single(nic->pdev,
2705 PCI_DMA_FROMDEVICE);
2706 if( (rxdp3->Buffer1_ptr == 0) ||
2707 (rxdp3->Buffer1_ptr == DMA_ERROR_CODE)) {
2710 (dma_addr_t)rxdp3->Buffer2_ptr,
2712 PCI_DMA_FROMDEVICE);
2713 goto pci_map_failed;
2715 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
2716 rxdp->Control_2 |= SET_BUFFER2_SIZE_3
2719 rxdp->Control_2 |= s2BIT(0);
2721 rxdp->Host_Control = (unsigned long) (skb);
2722 if (alloc_tab & ((1 << rxsync_frequency) - 1))
2723 rxdp->Control_1 |= RXD_OWN_XENA;
2725 if (off == (rxd_count[nic->rxd_mode] + 1))
2727 mac_control->rings[ring_no].rx_curr_put_info.offset = off;
2729 rxdp->Control_2 |= SET_RXD_MARKER;
2730 if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) {
2733 first_rxdp->Control_1 |= RXD_OWN_XENA;
2737 atomic_inc(&nic->rx_bufs_left[ring_no]);
2742 /* Transfer ownership of first descriptor to adapter just before
2743 * exiting. Before that, use memory barrier so that ownership
2744 * and other fields are seen by adapter correctly.
2748 first_rxdp->Control_1 |= RXD_OWN_XENA;
2753 stats->pci_map_fail_cnt++;
2754 stats->mem_freed += skb->truesize;
2755 dev_kfree_skb_irq(skb);
2759 static void free_rxd_blk(struct s2io_nic *sp, int ring_no, int blk)
2761 struct net_device *dev = sp->dev;
2763 struct sk_buff *skb;
2765 struct mac_info *mac_control;
2770 mac_control = &sp->mac_control;
2771 for (j = 0 ; j < rxd_count[sp->rxd_mode]; j++) {
2772 rxdp = mac_control->rings[ring_no].
2773 rx_blocks[blk].rxds[j].virt_addr;
2774 skb = (struct sk_buff *)
2775 ((unsigned long) rxdp->Host_Control);
2779 if (sp->rxd_mode == RXD_MODE_1) {
2780 rxdp1 = (struct RxD1*)rxdp;
2781 pci_unmap_single(sp->pdev, (dma_addr_t)
2784 HEADER_ETHERNET_II_802_3_SIZE
2785 + HEADER_802_2_SIZE +
2787 PCI_DMA_FROMDEVICE);
2788 memset(rxdp, 0, sizeof(struct RxD1));
2789 } else if(sp->rxd_mode == RXD_MODE_3B) {
2790 rxdp3 = (struct RxD3*)rxdp;
2791 ba = &mac_control->rings[ring_no].
2793 pci_unmap_single(sp->pdev, (dma_addr_t)
2796 PCI_DMA_FROMDEVICE);
2797 pci_unmap_single(sp->pdev, (dma_addr_t)
2800 PCI_DMA_FROMDEVICE);
2801 pci_unmap_single(sp->pdev, (dma_addr_t)
2804 PCI_DMA_FROMDEVICE);
2805 memset(rxdp, 0, sizeof(struct RxD3));
2807 sp->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
2809 atomic_dec(&sp->rx_bufs_left[ring_no]);
2814 * free_rx_buffers - Frees all Rx buffers
2815 * @sp: device private variable.
2817 * This function will free all Rx buffers allocated by host.
2822 static void free_rx_buffers(struct s2io_nic *sp)
2824 struct net_device *dev = sp->dev;
2825 int i, blk = 0, buf_cnt = 0;
2826 struct mac_info *mac_control;
2827 struct config_param *config;
2829 mac_control = &sp->mac_control;
2830 config = &sp->config;
2832 for (i = 0; i < config->rx_ring_num; i++) {
2833 for (blk = 0; blk < rx_ring_sz[i]; blk++)
2834 free_rxd_blk(sp,i,blk);
2836 mac_control->rings[i].rx_curr_put_info.block_index = 0;
2837 mac_control->rings[i].rx_curr_get_info.block_index = 0;
2838 mac_control->rings[i].rx_curr_put_info.offset = 0;
2839 mac_control->rings[i].rx_curr_get_info.offset = 0;
2840 atomic_set(&sp->rx_bufs_left[i], 0);
2841 DBG_PRINT(INIT_DBG, "%s:Freed 0x%x Rx Buffers on ring%d\n",
2842 dev->name, buf_cnt, i);
2847 * s2io_poll - Rx interrupt handler for NAPI support
2848 * @napi : pointer to the napi structure.
2849 * @budget : The number of packets that were budgeted to be processed
2850 * during one pass through the 'Poll" function.
2852 * Comes into picture only if NAPI support has been incorporated. It does
2853 * the same thing that rx_intr_handler does, but not in a interrupt context
2854 * also It will process only a given number of packets.
2856 * 0 on success and 1 if there are No Rx packets to be processed.
2859 static int s2io_poll(struct napi_struct *napi, int budget)
2861 struct s2io_nic *nic = container_of(napi, struct s2io_nic, napi);
2862 struct net_device *dev = nic->dev;
2863 int pkt_cnt = 0, org_pkts_to_process;
2864 struct mac_info *mac_control;
2865 struct config_param *config;
2866 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2869 mac_control = &nic->mac_control;
2870 config = &nic->config;
2872 nic->pkts_to_process = budget;
2873 org_pkts_to_process = nic->pkts_to_process;
2875 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
2876 readl(&bar0->rx_traffic_int);
2878 for (i = 0; i < config->rx_ring_num; i++) {
2879 rx_intr_handler(&mac_control->rings[i]);
2880 pkt_cnt = org_pkts_to_process - nic->pkts_to_process;
2881 if (!nic->pkts_to_process) {
2882 /* Quota for the current iteration has been met */
2887 netif_rx_complete(dev, napi);
2889 for (i = 0; i < config->rx_ring_num; i++) {
2890 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2891 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2892 DBG_PRINT(INFO_DBG, " in Rx Poll!!\n");
2896 /* Re enable the Rx interrupts. */
2897 writeq(0x0, &bar0->rx_traffic_mask);
2898 readl(&bar0->rx_traffic_mask);
2902 for (i = 0; i < config->rx_ring_num; i++) {
2903 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2904 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2905 DBG_PRINT(INFO_DBG, " in Rx Poll!!\n");
2912 #ifdef CONFIG_NET_POLL_CONTROLLER
2914 * s2io_netpoll - netpoll event handler entry point
2915 * @dev : pointer to the device structure.
2917 * This function will be called by upper layer to check for events on the
2918 * interface in situations where interrupts are disabled. It is used for
2919 * specific in-kernel networking tasks, such as remote consoles and kernel
2920 * debugging over the network (example netdump in RedHat).
2922 static void s2io_netpoll(struct net_device *dev)
2924 struct s2io_nic *nic = dev->priv;
2925 struct mac_info *mac_control;
2926 struct config_param *config;
2927 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2928 u64 val64 = 0xFFFFFFFFFFFFFFFFULL;
2931 if (pci_channel_offline(nic->pdev))
2934 disable_irq(dev->irq);
2936 mac_control = &nic->mac_control;
2937 config = &nic->config;
2939 writeq(val64, &bar0->rx_traffic_int);
2940 writeq(val64, &bar0->tx_traffic_int);
2942 /* we need to free up the transmitted skbufs or else netpoll will
2943 * run out of skbs and will fail and eventually netpoll application such
2944 * as netdump will fail.
2946 for (i = 0; i < config->tx_fifo_num; i++)
2947 tx_intr_handler(&mac_control->fifos[i]);
2949 /* check for received packet and indicate up to network */
2950 for (i = 0; i < config->rx_ring_num; i++)
2951 rx_intr_handler(&mac_control->rings[i]);
2953 for (i = 0; i < config->rx_ring_num; i++) {
2954 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2955 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2956 DBG_PRINT(INFO_DBG, " in Rx Netpoll!!\n");
2960 enable_irq(dev->irq);
2966 * rx_intr_handler - Rx interrupt handler
2967 * @nic: device private variable.
2969 * If the interrupt is because of a received frame or if the
2970 * receive ring contains fresh as yet un-processed frames,this function is
2971 * called. It picks out the RxD at which place the last Rx processing had
2972 * stopped and sends the skb to the OSM's Rx handler and then increments
2977 static void rx_intr_handler(struct ring_info *ring_data)
2979 struct s2io_nic *nic = ring_data->nic;
2980 struct net_device *dev = (struct net_device *) nic->dev;
2981 int get_block, put_block, put_offset;
2982 struct rx_curr_get_info get_info, put_info;
2984 struct sk_buff *skb;
2990 spin_lock(&nic->rx_lock);
2992 get_info = ring_data->rx_curr_get_info;
2993 get_block = get_info.block_index;
2994 memcpy(&put_info, &ring_data->rx_curr_put_info, sizeof(put_info));
2995 put_block = put_info.block_index;
2996 rxdp = ring_data->rx_blocks[get_block].rxds[get_info.offset].virt_addr;
2998 spin_lock(&nic->put_lock);
2999 put_offset = ring_data->put_pos;
3000 spin_unlock(&nic->put_lock);
3002 put_offset = ring_data->put_pos;
3004 while (RXD_IS_UP2DT(rxdp)) {
3006 * If your are next to put index then it's
3007 * FIFO full condition
3009 if ((get_block == put_block) &&
3010 (get_info.offset + 1) == put_info.offset) {
3011 DBG_PRINT(INTR_DBG, "%s: Ring Full\n",dev->name);
3014 skb = (struct sk_buff *) ((unsigned long)rxdp->Host_Control);
3016 DBG_PRINT(ERR_DBG, "%s: The skb is ",
3018 DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
3019 spin_unlock(&nic->rx_lock);
3022 if (nic->rxd_mode == RXD_MODE_1) {
3023 rxdp1 = (struct RxD1*)rxdp;
3024 pci_unmap_single(nic->pdev, (dma_addr_t)
3027 HEADER_ETHERNET_II_802_3_SIZE +
3030 PCI_DMA_FROMDEVICE);
3031 } else if (nic->rxd_mode == RXD_MODE_3B) {
3032 rxdp3 = (struct RxD3*)rxdp;
3033 pci_dma_sync_single_for_cpu(nic->pdev, (dma_addr_t)
3035 BUF0_LEN, PCI_DMA_FROMDEVICE);
3036 pci_unmap_single(nic->pdev, (dma_addr_t)
3039 PCI_DMA_FROMDEVICE);
3041 prefetch(skb->data);
3042 rx_osm_handler(ring_data, rxdp);
3044 ring_data->rx_curr_get_info.offset = get_info.offset;
3045 rxdp = ring_data->rx_blocks[get_block].
3046 rxds[get_info.offset].virt_addr;
3047 if (get_info.offset == rxd_count[nic->rxd_mode]) {
3048 get_info.offset = 0;
3049 ring_data->rx_curr_get_info.offset = get_info.offset;
3051 if (get_block == ring_data->block_count)
3053 ring_data->rx_curr_get_info.block_index = get_block;
3054 rxdp = ring_data->rx_blocks[get_block].block_virt_addr;
3057 nic->pkts_to_process -= 1;
3058 if ((napi) && (!nic->pkts_to_process))
3061 if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts))
3065 /* Clear all LRO sessions before exiting */
3066 for (i=0; i<MAX_LRO_SESSIONS; i++) {
3067 struct lro *lro = &nic->lro0_n[i];
3069 update_L3L4_header(nic, lro);
3070 queue_rx_frame(lro->parent, lro->vlan_tag);
3071 clear_lro_session(lro);
3076 spin_unlock(&nic->rx_lock);
3080 * tx_intr_handler - Transmit interrupt handler
3081 * @nic : device private variable
3083 * If an interrupt was raised to indicate DMA complete of the
3084 * Tx packet, this function is called. It identifies the last TxD
3085 * whose buffer was freed and frees all skbs whose data have already
3086 * DMA'ed into the NICs internal memory.
3091 static void tx_intr_handler(struct fifo_info *fifo_data)
3093 struct s2io_nic *nic = fifo_data->nic;
3094 struct tx_curr_get_info get_info, put_info;
3095 struct sk_buff *skb = NULL;
3098 unsigned long flags = 0;
3101 if (!spin_trylock_irqsave(&fifo_data->tx_lock, flags))
3104 get_info = fifo_data->tx_curr_get_info;
3105 memcpy(&put_info, &fifo_data->tx_curr_put_info, sizeof(put_info));
3106 txdlp = (struct TxD *) fifo_data->list_info[get_info.offset].
3108 while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) &&
3109 (get_info.offset != put_info.offset) &&
3110 (txdlp->Host_Control)) {
3111 /* Check for TxD errors */
3112 if (txdlp->Control_1 & TXD_T_CODE) {
3113 unsigned long long err;
3114 err = txdlp->Control_1 & TXD_T_CODE;
3116 nic->mac_control.stats_info->sw_stat.
3120 /* update t_code statistics */
3121 err_mask = err >> 48;
3124 nic->mac_control.stats_info->sw_stat.
3129 nic->mac_control.stats_info->sw_stat.
3130 tx_desc_abort_cnt++;
3134 nic->mac_control.stats_info->sw_stat.
3135 tx_parity_err_cnt++;
3139 nic->mac_control.stats_info->sw_stat.
3144 nic->mac_control.stats_info->sw_stat.
3145 tx_list_proc_err_cnt++;
3150 skb = s2io_txdl_getskb(fifo_data, txdlp, get_info.offset);
3152 spin_unlock_irqrestore(&fifo_data->tx_lock, flags);
3153 DBG_PRINT(ERR_DBG, "%s: Null skb ",
3155 DBG_PRINT(ERR_DBG, "in Tx Free Intr\n");
3160 /* Updating the statistics block */
3161 nic->stats.tx_bytes += skb->len;
3162 nic->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
3163 dev_kfree_skb_irq(skb);
3166 if (get_info.offset == get_info.fifo_len + 1)
3167 get_info.offset = 0;
3168 txdlp = (struct TxD *) fifo_data->list_info
3169 [get_info.offset].list_virt_addr;
3170 fifo_data->tx_curr_get_info.offset =
3174 s2io_wake_tx_queue(fifo_data, pkt_cnt, nic->config.multiq);
3176 spin_unlock_irqrestore(&fifo_data->tx_lock, flags);
3180 * s2io_mdio_write - Function to write in to MDIO registers
3181 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3182 * @addr : address value
3183 * @value : data value
3184 * @dev : pointer to net_device structure
3186 * This function is used to write values to the MDIO registers
3189 static void s2io_mdio_write(u32 mmd_type, u64 addr, u16 value, struct net_device *dev)
3192 struct s2io_nic *sp = dev->priv;
3193 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3195 //address transaction
3196 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3197 | MDIO_MMD_DEV_ADDR(mmd_type)
3198 | MDIO_MMS_PRT_ADDR(0x0);
3199 writeq(val64, &bar0->mdio_control);
3200 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3201 writeq(val64, &bar0->mdio_control);
3206 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3207 | MDIO_MMD_DEV_ADDR(mmd_type)
3208 | MDIO_MMS_PRT_ADDR(0x0)
3209 | MDIO_MDIO_DATA(value)
3210 | MDIO_OP(MDIO_OP_WRITE_TRANS);
3211 writeq(val64, &bar0->mdio_control);
3212 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3213 writeq(val64, &bar0->mdio_control);
3217 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3218 | MDIO_MMD_DEV_ADDR(mmd_type)
3219 | MDIO_MMS_PRT_ADDR(0x0)
3220 | MDIO_OP(MDIO_OP_READ_TRANS);
3221 writeq(val64, &bar0->mdio_control);
3222 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3223 writeq(val64, &bar0->mdio_control);
3229 * s2io_mdio_read - Function to write in to MDIO registers
3230 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3231 * @addr : address value
3232 * @dev : pointer to net_device structure
3234 * This function is used to read values to the MDIO registers
3237 static u64 s2io_mdio_read(u32 mmd_type, u64 addr, struct net_device *dev)
3241 struct s2io_nic *sp = dev->priv;
3242 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3244 /* address transaction */
3245 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3246 | MDIO_MMD_DEV_ADDR(mmd_type)
3247 | MDIO_MMS_PRT_ADDR(0x0);
3248 writeq(val64, &bar0->mdio_control);
3249 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3250 writeq(val64, &bar0->mdio_control);
3253 /* Data transaction */
3255 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3256 | MDIO_MMD_DEV_ADDR(mmd_type)
3257 | MDIO_MMS_PRT_ADDR(0x0)
3258 | MDIO_OP(MDIO_OP_READ_TRANS);
3259 writeq(val64, &bar0->mdio_control);
3260 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3261 writeq(val64, &bar0->mdio_control);
3264 /* Read the value from regs */
3265 rval64 = readq(&bar0->mdio_control);
3266 rval64 = rval64 & 0xFFFF0000;
3267 rval64 = rval64 >> 16;
3271 * s2io_chk_xpak_counter - Function to check the status of the xpak counters
3272 * @counter : couter value to be updated
3273 * @flag : flag to indicate the status
3274 * @type : counter type
3276 * This function is to check the status of the xpak counters value
3280 static void s2io_chk_xpak_counter(u64 *counter, u64 * regs_stat, u32 index, u16 flag, u16 type)
3285 for(i = 0; i <index; i++)
3290 *counter = *counter + 1;
3291 val64 = *regs_stat & mask;
3292 val64 = val64 >> (index * 0x2);
3299 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3300 "service. Excessive temperatures may "
3301 "result in premature transceiver "
3305 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3306 "service Excessive bias currents may "
3307 "indicate imminent laser diode "
3311 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3312 "service Excessive laser output "
3313 "power may saturate far-end "
3317 DBG_PRINT(ERR_DBG, "Incorrect XPAK Alarm "
3322 val64 = val64 << (index * 0x2);
3323 *regs_stat = (*regs_stat & (~mask)) | (val64);
3326 *regs_stat = *regs_stat & (~mask);
3331 * s2io_updt_xpak_counter - Function to update the xpak counters
3332 * @dev : pointer to net_device struct
3334 * This function is to upate the status of the xpak counters value
3337 static void s2io_updt_xpak_counter(struct net_device *dev)
3345 struct s2io_nic *sp = dev->priv;
3346 struct stat_block *stat_info = sp->mac_control.stats_info;
3348 /* Check the communication with the MDIO slave */
3351 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3352 if((val64 == 0xFFFF) || (val64 == 0x0000))
3354 DBG_PRINT(ERR_DBG, "ERR: MDIO slave access failed - "
3355 "Returned %llx\n", (unsigned long long)val64);
3359 /* Check for the expecte value of 2040 at PMA address 0x0000 */
3362 DBG_PRINT(ERR_DBG, "Incorrect value at PMA address 0x0000 - ");
3363 DBG_PRINT(ERR_DBG, "Returned: %llx- Expected: 0x2040\n",
3364 (unsigned long long)val64);
3368 /* Loading the DOM register to MDIO register */
3370 s2io_mdio_write(MDIO_MMD_PMA_DEV_ADDR, addr, val16, dev);
3371 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3373 /* Reading the Alarm flags */
3376 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3378 flag = CHECKBIT(val64, 0x7);
3380 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_transceiver_temp_high,
3381 &stat_info->xpak_stat.xpak_regs_stat,
3384 if(CHECKBIT(val64, 0x6))
3385 stat_info->xpak_stat.alarm_transceiver_temp_low++;
3387 flag = CHECKBIT(val64, 0x3);
3389 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_laser_bias_current_high,
3390 &stat_info->xpak_stat.xpak_regs_stat,
3393 if(CHECKBIT(val64, 0x2))
3394 stat_info->xpak_stat.alarm_laser_bias_current_low++;
3396 flag = CHECKBIT(val64, 0x1);
3398 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_laser_output_power_high,
3399 &stat_info->xpak_stat.xpak_regs_stat,
3402 if(CHECKBIT(val64, 0x0))
3403 stat_info->xpak_stat.alarm_laser_output_power_low++;
3405 /* Reading the Warning flags */
3408 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3410 if(CHECKBIT(val64, 0x7))
3411 stat_info->xpak_stat.warn_transceiver_temp_high++;
3413 if(CHECKBIT(val64, 0x6))
3414 stat_info->xpak_stat.warn_transceiver_temp_low++;
3416 if(CHECKBIT(val64, 0x3))
3417 stat_info->xpak_stat.warn_laser_bias_current_high++;
3419 if(CHECKBIT(val64, 0x2))
3420 stat_info->xpak_stat.warn_laser_bias_current_low++;
3422 if(CHECKBIT(val64, 0x1))
3423 stat_info->xpak_stat.warn_laser_output_power_high++;
3425 if(CHECKBIT(val64, 0x0))
3426 stat_info->xpak_stat.warn_laser_output_power_low++;
3430 * wait_for_cmd_complete - waits for a command to complete.
3431 * @sp : private member of the device structure, which is a pointer to the
3432 * s2io_nic structure.
3433 * Description: Function that waits for a command to Write into RMAC
3434 * ADDR DATA registers to be completed and returns either success or
3435 * error depending on whether the command was complete or not.
3437 * SUCCESS on success and FAILURE on failure.
3440 static int wait_for_cmd_complete(void __iomem *addr, u64 busy_bit,
3443 int ret = FAILURE, cnt = 0, delay = 1;
3446 if ((bit_state != S2IO_BIT_RESET) && (bit_state != S2IO_BIT_SET))
3450 val64 = readq(addr);
3451 if (bit_state == S2IO_BIT_RESET) {
3452 if (!(val64 & busy_bit)) {
3457 if (!(val64 & busy_bit)) {
3474 * check_pci_device_id - Checks if the device id is supported
3476 * Description: Function to check if the pci device id is supported by driver.
3477 * Return value: Actual device id if supported else PCI_ANY_ID
3479 static u16 check_pci_device_id(u16 id)
3482 case PCI_DEVICE_ID_HERC_WIN:
3483 case PCI_DEVICE_ID_HERC_UNI:
3484 return XFRAME_II_DEVICE;
3485 case PCI_DEVICE_ID_S2IO_UNI:
3486 case PCI_DEVICE_ID_S2IO_WIN:
3487 return XFRAME_I_DEVICE;
3494 * s2io_reset - Resets the card.
3495 * @sp : private member of the device structure.
3496 * Description: Function to Reset the card. This function then also
3497 * restores the previously saved PCI configuration space registers as
3498 * the card reset also resets the configuration space.
3503 static void s2io_reset(struct s2io_nic * sp)
3505 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3510 unsigned long long up_cnt, down_cnt, up_time, down_time, reset_cnt;
3511 unsigned long long mem_alloc_cnt, mem_free_cnt, watchdog_cnt;
3513 DBG_PRINT(INIT_DBG,"%s - Resetting XFrame card %s\n",
3514 __FUNCTION__, sp->dev->name);
3516 /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
3517 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
3519 val64 = SW_RESET_ALL;
3520 writeq(val64, &bar0->sw_reset);
3521 if (strstr(sp->product_name, "CX4")) {
3525 for (i = 0; i < S2IO_MAX_PCI_CONFIG_SPACE_REINIT; i++) {
3527 /* Restore the PCI state saved during initialization. */
3528 pci_restore_state(sp->pdev);
3529 pci_read_config_word(sp->pdev, 0x2, &val16);
3530 if (check_pci_device_id(val16) != (u16)PCI_ANY_ID)
3535 if (check_pci_device_id(val16) == (u16)PCI_ANY_ID) {
3536 DBG_PRINT(ERR_DBG,"%s SW_Reset failed!\n", __FUNCTION__);
3539 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, pci_cmd);
3543 /* Set swapper to enable I/O register access */
3544 s2io_set_swapper(sp);
3546 /* restore mac_addr entries */
3547 do_s2io_restore_unicast_mc(sp);
3549 /* Restore the MSIX table entries from local variables */
3550 restore_xmsi_data(sp);
3552 /* Clear certain PCI/PCI-X fields after reset */
3553 if (sp->device_type == XFRAME_II_DEVICE) {
3554 /* Clear "detected parity error" bit */
3555 pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000);
3557 /* Clearing PCIX Ecc status register */
3558 pci_write_config_dword(sp->pdev, 0x68, 0x7C);
3560 /* Clearing PCI_STATUS error reflected here */
3561 writeq(s2BIT(62), &bar0->txpic_int_reg);
3564 /* Reset device statistics maintained by OS */
3565 memset(&sp->stats, 0, sizeof (struct net_device_stats));
3567 up_cnt = sp->mac_control.stats_info->sw_stat.link_up_cnt;
3568 down_cnt = sp->mac_control.stats_info->sw_stat.link_down_cnt;
3569 up_time = sp->mac_control.stats_info->sw_stat.link_up_time;
3570 down_time = sp->mac_control.stats_info->sw_stat.link_down_time;
3571 reset_cnt = sp->mac_control.stats_info->sw_stat.soft_reset_cnt;
3572 mem_alloc_cnt = sp->mac_control.stats_info->sw_stat.mem_allocated;
3573 mem_free_cnt = sp->mac_control.stats_info->sw_stat.mem_freed;
3574 watchdog_cnt = sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt;
3575 /* save link up/down time/cnt, reset/memory/watchdog cnt */
3576 memset(sp->mac_control.stats_info, 0, sizeof(struct stat_block));
3577 /* restore link up/down time/cnt, reset/memory/watchdog cnt */
3578 sp->mac_control.stats_info->sw_stat.link_up_cnt = up_cnt;
3579 sp->mac_control.stats_info->sw_stat.link_down_cnt = down_cnt;
3580 sp->mac_control.stats_info->sw_stat.link_up_time = up_time;
3581 sp->mac_control.stats_info->sw_stat.link_down_time = down_time;
3582 sp->mac_control.stats_info->sw_stat.soft_reset_cnt = reset_cnt;
3583 sp->mac_control.stats_info->sw_stat.mem_allocated = mem_alloc_cnt;
3584 sp->mac_control.stats_info->sw_stat.mem_freed = mem_free_cnt;
3585 sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt = watchdog_cnt;
3587 /* SXE-002: Configure link and activity LED to turn it off */
3588 subid = sp->pdev->subsystem_device;
3589 if (((subid & 0xFF) >= 0x07) &&
3590 (sp->device_type == XFRAME_I_DEVICE)) {
3591 val64 = readq(&bar0->gpio_control);
3592 val64 |= 0x0000800000000000ULL;
3593 writeq(val64, &bar0->gpio_control);
3594 val64 = 0x0411040400000000ULL;
3595 writeq(val64, (void __iomem *)bar0 + 0x2700);
3599 * Clear spurious ECC interrupts that would have occured on
3600 * XFRAME II cards after reset.
3602 if (sp->device_type == XFRAME_II_DEVICE) {
3603 val64 = readq(&bar0->pcc_err_reg);
3604 writeq(val64, &bar0->pcc_err_reg);
3607 sp->device_enabled_once = FALSE;
3611 * s2io_set_swapper - to set the swapper controle on the card
3612 * @sp : private member of the device structure,
3613 * pointer to the s2io_nic structure.
3614 * Description: Function to set the swapper control on the card
3615 * correctly depending on the 'endianness' of the system.
3617 * SUCCESS on success and FAILURE on failure.
3620 static int s2io_set_swapper(struct s2io_nic * sp)
3622 struct net_device *dev = sp->dev;
3623 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3624 u64 val64, valt, valr;
3627 * Set proper endian settings and verify the same by reading
3628 * the PIF Feed-back register.
3631 val64 = readq(&bar0->pif_rd_swapper_fb);
3632 if (val64 != 0x0123456789ABCDEFULL) {
3634 u64 value[] = { 0xC30000C3C30000C3ULL, /* FE=1, SE=1 */
3635 0x8100008181000081ULL, /* FE=1, SE=0 */
3636 0x4200004242000042ULL, /* FE=0, SE=1 */
3637 0}; /* FE=0, SE=0 */
3640 writeq(value[i], &bar0->swapper_ctrl);
3641 val64 = readq(&bar0->pif_rd_swapper_fb);
3642 if (val64 == 0x0123456789ABCDEFULL)
3647 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, ",
3649 DBG_PRINT(ERR_DBG, "feedback read %llx\n",
3650 (unsigned long long) val64);
3655 valr = readq(&bar0->swapper_ctrl);
3658 valt = 0x0123456789ABCDEFULL;
3659 writeq(valt, &bar0->xmsi_address);
3660 val64 = readq(&bar0->xmsi_address);
3664 u64 value[] = { 0x00C3C30000C3C300ULL, /* FE=1, SE=1 */
3665 0x0081810000818100ULL, /* FE=1, SE=0 */
3666 0x0042420000424200ULL, /* FE=0, SE=1 */
3667 0}; /* FE=0, SE=0 */
3670 writeq((value[i] | valr), &bar0->swapper_ctrl);
3671 writeq(valt, &bar0->xmsi_address);
3672 val64 = readq(&bar0->xmsi_address);
3678 unsigned long long x = val64;
3679 DBG_PRINT(ERR_DBG, "Write failed, Xmsi_addr ");
3680 DBG_PRINT(ERR_DBG, "reads:0x%llx\n", x);
3684 val64 = readq(&bar0->swapper_ctrl);
3685 val64 &= 0xFFFF000000000000ULL;
3689 * The device by default set to a big endian format, so a
3690 * big endian driver need not set anything.
3692 val64 |= (SWAPPER_CTRL_TXP_FE |
3693 SWAPPER_CTRL_TXP_SE |
3694 SWAPPER_CTRL_TXD_R_FE |
3695 SWAPPER_CTRL_TXD_W_FE |
3696 SWAPPER_CTRL_TXF_R_FE |
3697 SWAPPER_CTRL_RXD_R_FE |
3698 SWAPPER_CTRL_RXD_W_FE |
3699 SWAPPER_CTRL_RXF_W_FE |
3700 SWAPPER_CTRL_XMSI_FE |
3701 SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
3702 if (sp->config.intr_type == INTA)
3703 val64 |= SWAPPER_CTRL_XMSI_SE;
3704 writeq(val64, &bar0->swapper_ctrl);
3707 * Initially we enable all bits to make it accessible by the
3708 * driver, then we selectively enable only those bits that
3711 val64 |= (SWAPPER_CTRL_TXP_FE |
3712 SWAPPER_CTRL_TXP_SE |
3713 SWAPPER_CTRL_TXD_R_FE |
3714 SWAPPER_CTRL_TXD_R_SE |
3715 SWAPPER_CTRL_TXD_W_FE |
3716 SWAPPER_CTRL_TXD_W_SE |
3717 SWAPPER_CTRL_TXF_R_FE |
3718 SWAPPER_CTRL_RXD_R_FE |
3719 SWAPPER_CTRL_RXD_R_SE |
3720 SWAPPER_CTRL_RXD_W_FE |
3721 SWAPPER_CTRL_RXD_W_SE |
3722 SWAPPER_CTRL_RXF_W_FE |
3723 SWAPPER_CTRL_XMSI_FE |
3724 SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
3725 if (sp->config.intr_type == INTA)
3726 val64 |= SWAPPER_CTRL_XMSI_SE;
3727 writeq(val64, &bar0->swapper_ctrl);
3729 val64 = readq(&bar0->swapper_ctrl);
3732 * Verifying if endian settings are accurate by reading a
3733 * feedback register.
3735 val64 = readq(&bar0->pif_rd_swapper_fb);
3736 if (val64 != 0x0123456789ABCDEFULL) {
3737 /* Endian settings are incorrect, calls for another dekko. */
3738 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, ",
3740 DBG_PRINT(ERR_DBG, "feedback read %llx\n",
3741 (unsigned long long) val64);
3748 static int wait_for_msix_trans(struct s2io_nic *nic, int i)
3750 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3752 int ret = 0, cnt = 0;
3755 val64 = readq(&bar0->xmsi_access);
3756 if (!(val64 & s2BIT(15)))
3762 DBG_PRINT(ERR_DBG, "XMSI # %d Access failed\n", i);
3769 static void restore_xmsi_data(struct s2io_nic *nic)
3771 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3775 for (i=0; i < MAX_REQUESTED_MSI_X; i++) {
3776 writeq(nic->msix_info[i].addr, &bar0->xmsi_address);
3777 writeq(nic->msix_info[i].data, &bar0->xmsi_data);
3778 val64 = (s2BIT(7) | s2BIT(15) | vBIT(i, 26, 6));
3779 writeq(val64, &bar0->xmsi_access);
3780 if (wait_for_msix_trans(nic, i)) {
3781 DBG_PRINT(ERR_DBG, "failed in %s\n", __FUNCTION__);
3787 static void store_xmsi_data(struct s2io_nic *nic)
3789 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3790 u64 val64, addr, data;
3793 /* Store and display */
3794 for (i=0; i < MAX_REQUESTED_MSI_X; i++) {
3795 val64 = (s2BIT(15) | vBIT(i, 26, 6));
3796 writeq(val64, &bar0->xmsi_access);
3797 if (wait_for_msix_trans(nic, i)) {
3798 DBG_PRINT(ERR_DBG, "failed in %s\n", __FUNCTION__);
3801 addr = readq(&bar0->xmsi_address);
3802 data = readq(&bar0->xmsi_data);
3804 nic->msix_info[i].addr = addr;
3805 nic->msix_info[i].data = data;
3810 static int s2io_enable_msi_x(struct s2io_nic *nic)
3812 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3814 u16 msi_control; /* Temp variable */
3815 int ret, i, j, msix_indx = 1;
3817 nic->entries = kcalloc(MAX_REQUESTED_MSI_X, sizeof(struct msix_entry),
3819 if (!nic->entries) {
3820 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n", \
3822 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
3825 nic->mac_control.stats_info->sw_stat.mem_allocated
3826 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3829 kcalloc(MAX_REQUESTED_MSI_X, sizeof(struct s2io_msix_entry),
3831 if (!nic->s2io_entries) {
3832 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n",
3834 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
3835 kfree(nic->entries);
3836 nic->mac_control.stats_info->sw_stat.mem_freed
3837 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3840 nic->mac_control.stats_info->sw_stat.mem_allocated
3841 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3843 for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
3844 nic->entries[i].entry = i;
3845 nic->s2io_entries[i].entry = i;
3846 nic->s2io_entries[i].arg = NULL;
3847 nic->s2io_entries[i].in_use = 0;
3850 tx_mat = readq(&bar0->tx_mat0_n[0]);
3851 for (i=0; i<nic->config.tx_fifo_num; i++, msix_indx++) {
3852 tx_mat |= TX_MAT_SET(i, msix_indx);
3853 nic->s2io_entries[msix_indx].arg = &nic->mac_control.fifos[i];
3854 nic->s2io_entries[msix_indx].type = MSIX_FIFO_TYPE;
3855 nic->s2io_entries[msix_indx].in_use = MSIX_FLG;
3857 writeq(tx_mat, &bar0->tx_mat0_n[0]);
3859 rx_mat = readq(&bar0->rx_mat);
3860 for (j = 0; j < nic->config.rx_ring_num; j++, msix_indx++) {
3861 rx_mat |= RX_MAT_SET(j, msix_indx);
3862 nic->s2io_entries[msix_indx].arg
3863 = &nic->mac_control.rings[j];
3864 nic->s2io_entries[msix_indx].type = MSIX_RING_TYPE;
3865 nic->s2io_entries[msix_indx].in_use = MSIX_FLG;
3867 writeq(rx_mat, &bar0->rx_mat);
3869 nic->avail_msix_vectors = 0;
3870 ret = pci_enable_msix(nic->pdev, nic->entries, MAX_REQUESTED_MSI_X);
3871 /* We fail init if error or we get less vectors than min required */
3872 if (ret >= (nic->config.tx_fifo_num + nic->config.rx_ring_num + 1)) {
3873 nic->avail_msix_vectors = ret;
3874 ret = pci_enable_msix(nic->pdev, nic->entries, ret);
3877 DBG_PRINT(ERR_DBG, "%s: Enabling MSIX failed\n", nic->dev->name);
3878 kfree(nic->entries);
3879 nic->mac_control.stats_info->sw_stat.mem_freed
3880 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3881 kfree(nic->s2io_entries);
3882 nic->mac_control.stats_info->sw_stat.mem_freed
3883 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3884 nic->entries = NULL;
3885 nic->s2io_entries = NULL;
3886 nic->avail_msix_vectors = 0;
3889 if (!nic->avail_msix_vectors)
3890 nic->avail_msix_vectors = MAX_REQUESTED_MSI_X;
3893 * To enable MSI-X, MSI also needs to be enabled, due to a bug
3894 * in the herc NIC. (Temp change, needs to be removed later)
3896 pci_read_config_word(nic->pdev, 0x42, &msi_control);
3897 msi_control |= 0x1; /* Enable MSI */
3898 pci_write_config_word(nic->pdev, 0x42, msi_control);
3903 /* Handle software interrupt used during MSI(X) test */
3904 static irqreturn_t s2io_test_intr(int irq, void *dev_id)
3906 struct s2io_nic *sp = dev_id;
3908 sp->msi_detected = 1;
3909 wake_up(&sp->msi_wait);
3914 /* Test interrupt path by forcing a a software IRQ */
3915 static int s2io_test_msi(struct s2io_nic *sp)
3917 struct pci_dev *pdev = sp->pdev;
3918 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3922 err = request_irq(sp->entries[1].vector, s2io_test_intr, 0,
3925 DBG_PRINT(ERR_DBG, "%s: PCI %s: cannot assign irq %d\n",
3926 sp->dev->name, pci_name(pdev), pdev->irq);
3930 init_waitqueue_head (&sp->msi_wait);
3931 sp->msi_detected = 0;
3933 saved64 = val64 = readq(&bar0->scheduled_int_ctrl);
3934 val64 |= SCHED_INT_CTRL_ONE_SHOT;
3935 val64 |= SCHED_INT_CTRL_TIMER_EN;
3936 val64 |= SCHED_INT_CTRL_INT2MSI(1);
3937 writeq(val64, &bar0->scheduled_int_ctrl);
3939 wait_event_timeout(sp->msi_wait, sp->msi_detected, HZ/10);
3941 if (!sp->msi_detected) {
3942 /* MSI(X) test failed, go back to INTx mode */
3943 DBG_PRINT(ERR_DBG, "%s: PCI %s: No interrupt was generated "
3944 "using MSI(X) during test\n", sp->dev->name,
3950 free_irq(sp->entries[1].vector, sp);
3952 writeq(saved64, &bar0->scheduled_int_ctrl);
3957 static void remove_msix_isr(struct s2io_nic *sp)
3962 for (i = 0; i < MAX_REQUESTED_MSI_X; i++) {
3963 if (sp->s2io_entries[i].in_use ==
3964 MSIX_REGISTERED_SUCCESS) {
3965 int vector = sp->entries[i].vector;
3966 void *arg = sp->s2io_entries[i].arg;
3967 free_irq(vector, arg);
3972 kfree(sp->s2io_entries);
3974 sp->s2io_entries = NULL;
3976 pci_read_config_word(sp->pdev, 0x42, &msi_control);
3977 msi_control &= 0xFFFE; /* Disable MSI */
3978 pci_write_config_word(sp->pdev, 0x42, msi_control);
3980 pci_disable_msix(sp->pdev);
3983 static void remove_inta_isr(struct s2io_nic *sp)
3985 struct net_device *dev = sp->dev;
3987 free_irq(sp->pdev->irq, dev);
3990 /* ********************************************************* *
3991 * Functions defined below concern the OS part of the driver *
3992 * ********************************************************* */
3995 * s2io_open - open entry point of the driver
3996 * @dev : pointer to the device structure.
3998 * This function is the open entry point of the driver. It mainly calls a
3999 * function to allocate Rx buffers and inserts them into the buffer
4000 * descriptors and then enables the Rx part of the NIC.
4002 * 0 on success and an appropriate (-)ve integer as defined in errno.h
4006 static int s2io_open(struct net_device *dev)
4008 struct s2io_nic *sp = dev->priv;
4012 * Make sure you have link off by default every time
4013 * Nic is initialized
4015 netif_carrier_off(dev);
4016 sp->last_link_state = 0;
4018 if (sp->config.intr_type == MSI_X) {
4019 int ret = s2io_enable_msi_x(sp);
4022 ret = s2io_test_msi(sp);
4023 /* rollback MSI-X, will re-enable during add_isr() */
4024 remove_msix_isr(sp);
4029 "%s: MSI-X requested but failed to enable\n",
4031 sp->config.intr_type = INTA;
4035 /* NAPI doesn't work well with MSI(X) */
4036 if (sp->config.intr_type != INTA) {
4038 sp->config.napi = 0;
4041 /* Initialize H/W and enable interrupts */
4042 err = s2io_card_up(sp);
4044 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
4046 goto hw_init_failed;
4049 if (do_s2io_prog_unicast(dev, dev->dev_addr) == FAILURE) {
4050 DBG_PRINT(ERR_DBG, "Set Mac Address Failed\n");
4053 goto hw_init_failed;
4055 s2io_start_all_tx_queue(sp);
4059 if (sp->config.intr_type == MSI_X) {
4062 sp->mac_control.stats_info->sw_stat.mem_freed
4063 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
4065 if (sp->s2io_entries) {
4066 kfree(sp->s2io_entries);
4067 sp->mac_control.stats_info->sw_stat.mem_freed
4068 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
4075 * s2io_close -close entry point of the driver
4076 * @dev : device pointer.
4078 * This is the stop entry point of the driver. It needs to undo exactly
4079 * whatever was done by the open entry point,thus it's usually referred to
4080 * as the close function.Among other things this function mainly stops the
4081 * Rx side of the NIC and frees all the Rx buffers in the Rx rings.
4083 * 0 on success and an appropriate (-)ve integer as defined in errno.h
4087 static int s2io_close(struct net_device *dev)
4089 struct s2io_nic *sp = dev->priv;
4090 struct config_param *config = &sp->config;
4094 /* Return if the device is already closed *
4095 * Can happen when s2io_card_up failed in change_mtu *
4097 if (!is_s2io_card_up(sp))
4100 s2io_stop_all_tx_queue(sp);
4101 /* delete all populated mac entries */
4102 for (offset = 1; offset < config->max_mc_addr; offset++) {
4103 tmp64 = do_s2io_read_unicast_mc(sp, offset);
4104 if (tmp64 != S2IO_DISABLE_MAC_ENTRY)
4105 do_s2io_delete_unicast_mc(sp, tmp64);
4108 /* Reset card, kill tasklet and free Tx and Rx buffers. */
4115 * s2io_xmit - Tx entry point of te driver
4116 * @skb : the socket buffer containing the Tx data.
4117 * @dev : device pointer.
4119 * This function is the Tx entry point of the driver. S2IO NIC supports
4120 * certain protocol assist features on Tx side, namely CSO, S/G, LSO.
4121 * NOTE: when device cant queue the pkt,just the trans_start variable will
4124 * 0 on success & 1 on failure.
4127 static int s2io_xmit(struct sk_buff *skb, struct net_device *dev)
4129 struct s2io_nic *sp = dev->priv;
4130 u16 frg_cnt, frg_len, i, queue, queue_len, put_off, get_off;
4133 struct TxFIFO_element __iomem *tx_fifo;
4134 unsigned long flags = 0;
4136 struct fifo_info *fifo = NULL;
4137 struct mac_info *mac_control;
4138 struct config_param *config;
4139 int do_spin_lock = 1;
4141 int enable_per_list_interrupt = 0;
4142 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
4144 mac_control = &sp->mac_control;
4145 config = &sp->config;
4147 DBG_PRINT(TX_DBG, "%s: In Neterion Tx routine\n", dev->name);
4149 if (unlikely(skb->len <= 0)) {
4150 DBG_PRINT(TX_DBG, "%s:Buffer has no data..\n", dev->name);
4151 dev_kfree_skb_any(skb);
4155 if (!is_s2io_card_up(sp)) {
4156 DBG_PRINT(TX_DBG, "%s: Card going down for reset\n",
4163 if (sp->vlgrp && vlan_tx_tag_present(skb))
4164 vlan_tag = vlan_tx_tag_get(skb);
4165 if (sp->config.tx_steering_type == TX_DEFAULT_STEERING) {
4166 if (skb->protocol == htons(ETH_P_IP)) {
4171 if ((ip->frag_off & htons(IP_OFFSET|IP_MF)) == 0) {
4172 th = (struct tcphdr *)(((unsigned char *)ip) +
4175 if (ip->protocol == IPPROTO_TCP) {
4176 queue_len = sp->total_tcp_fifos;
4177 queue = (ntohs(th->source) +
4179 sp->fifo_selector[queue_len - 1];
4180 if (queue >= queue_len)
4181 queue = queue_len - 1;
4182 } else if (ip->protocol == IPPROTO_UDP) {
4183 queue_len = sp->total_udp_fifos;
4184 queue = (ntohs(th->source) +
4186 sp->fifo_selector[queue_len - 1];
4187 if (queue >= queue_len)
4188 queue = queue_len - 1;
4189 queue += sp->udp_fifo_idx;
4190 if (skb->len > 1024)
4191 enable_per_list_interrupt = 1;
4196 } else if (sp->config.tx_steering_type == TX_PRIORITY_STEERING)
4197 /* get fifo number based on skb->priority value */
4198 queue = config->fifo_mapping
4199 [skb->priority & (MAX_TX_FIFOS - 1)];
4200 fifo = &mac_control->fifos[queue];
4203 spin_lock_irqsave(&fifo->tx_lock, flags);
4205 if (unlikely(!spin_trylock_irqsave(&fifo->tx_lock, flags)))
4206 return NETDEV_TX_LOCKED;
4209 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
4210 if (sp->config.multiq) {
4211 if (__netif_subqueue_stopped(dev, fifo->fifo_no)) {
4212 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4213 return NETDEV_TX_BUSY;
4217 if (unlikely(fifo->queue_state == FIFO_QUEUE_STOP)) {
4218 if (netif_queue_stopped(dev)) {
4219 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4220 return NETDEV_TX_BUSY;
4224 put_off = (u16) fifo->tx_curr_put_info.offset;
4225 get_off = (u16) fifo->tx_curr_get_info.offset;
4226 txdp = (struct TxD *) fifo->list_info[put_off].list_virt_addr;
4228 queue_len = fifo->tx_curr_put_info.fifo_len + 1;
4229 /* Avoid "put" pointer going beyond "get" pointer */
4230 if (txdp->Host_Control ||
4231 ((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4232 DBG_PRINT(TX_DBG, "Error in xmit, No free TXDs.\n");
4233 s2io_stop_tx_queue(sp, fifo->fifo_no);
4235 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4239 offload_type = s2io_offload_type(skb);
4240 if (offload_type & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6)) {
4241 txdp->Control_1 |= TXD_TCP_LSO_EN;
4242 txdp->Control_1 |= TXD_TCP_LSO_MSS(s2io_tcp_mss(skb));
4244 if (skb->ip_summed == CHECKSUM_PARTIAL) {
4246 (TXD_TX_CKO_IPV4_EN | TXD_TX_CKO_TCP_EN |
4249 txdp->Control_1 |= TXD_GATHER_CODE_FIRST;
4250 txdp->Control_1 |= TXD_LIST_OWN_XENA;
4251 txdp->Control_2 |= TXD_INT_NUMBER(fifo->fifo_no);
4252 if (enable_per_list_interrupt)
4253 if (put_off & (queue_len >> 5))
4254 txdp->Control_2 |= TXD_INT_TYPE_PER_LIST;
4256 txdp->Control_2 |= TXD_VLAN_ENABLE;
4257 txdp->Control_2 |= TXD_VLAN_TAG(vlan_tag);
4260 frg_len = skb->len - skb->data_len;
4261 if (offload_type == SKB_GSO_UDP) {
4264 ufo_size = s2io_udp_mss(skb);
4266 txdp->Control_1 |= TXD_UFO_EN;
4267 txdp->Control_1 |= TXD_UFO_MSS(ufo_size);
4268 txdp->Control_1 |= TXD_BUFFER0_SIZE(8);
4270 /* both variants do cpu_to_be64(be32_to_cpu(...)) */
4271 fifo->ufo_in_band_v[put_off] =
4272 (__force u64)skb_shinfo(skb)->ip6_frag_id;
4274 fifo->ufo_in_band_v[put_off] =
4275 (__force u64)skb_shinfo(skb)->ip6_frag_id << 32;
4277 txdp->Host_Control = (unsigned long)fifo->ufo_in_band_v;
4278 txdp->Buffer_Pointer = pci_map_single(sp->pdev,
4279 fifo->ufo_in_band_v,
4280 sizeof(u64), PCI_DMA_TODEVICE);
4281 if((txdp->Buffer_Pointer == 0) ||
4282 (txdp->Buffer_Pointer == DMA_ERROR_CODE))
4283 goto pci_map_failed;
4287 txdp->Buffer_Pointer = pci_map_single
4288 (sp->pdev, skb->data, frg_len, PCI_DMA_TODEVICE);
4289 if((txdp->Buffer_Pointer == 0) ||
4290 (txdp->Buffer_Pointer == DMA_ERROR_CODE))
4291 goto pci_map_failed;
4293 txdp->Host_Control = (unsigned long) skb;
4294 txdp->Control_1 |= TXD_BUFFER0_SIZE(frg_len);
4295 if (offload_type == SKB_GSO_UDP)
4296 txdp->Control_1 |= TXD_UFO_EN;
4298 frg_cnt = skb_shinfo(skb)->nr_frags;
4299 /* For fragmented SKB. */
4300 for (i = 0; i < frg_cnt; i++) {
4301 skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
4302 /* A '0' length fragment will be ignored */
4306 txdp->Buffer_Pointer = (u64) pci_map_page
4307 (sp->pdev, frag->page, frag->page_offset,
4308 frag->size, PCI_DMA_TODEVICE);
4309 txdp->Control_1 = TXD_BUFFER0_SIZE(frag->size);
4310 if (offload_type == SKB_GSO_UDP)
4311 txdp->Control_1 |= TXD_UFO_EN;
4313 txdp->Control_1 |= TXD_GATHER_CODE_LAST;
4315 if (offload_type == SKB_GSO_UDP)
4316 frg_cnt++; /* as Txd0 was used for inband header */
4318 tx_fifo = mac_control->tx_FIFO_start[queue];
4319 val64 = fifo->list_info[put_off].list_phy_addr;
4320 writeq(val64, &tx_fifo->TxDL_Pointer);
4322 val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
4325 val64 |= TX_FIFO_SPECIAL_FUNC;
4327 writeq(val64, &tx_fifo->List_Control);
4332 if (put_off == fifo->tx_curr_put_info.fifo_len + 1)
4334 fifo->tx_curr_put_info.offset = put_off;
4336 /* Avoid "put" pointer going beyond "get" pointer */
4337 if (((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4338 sp->mac_control.stats_info->sw_stat.fifo_full_cnt++;
4340 "No free TxDs for xmit, Put: 0x%x Get:0x%x\n",
4342 s2io_stop_tx_queue(sp, fifo->fifo_no);
4344 mac_control->stats_info->sw_stat.mem_allocated += skb->truesize;
4345 dev->trans_start = jiffies;
4346 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4350 stats->pci_map_fail_cnt++;
4351 s2io_stop_tx_queue(sp, fifo->fifo_no);
4352 stats->mem_freed += skb->truesize;
4354 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4359 s2io_alarm_handle(unsigned long data)
4361 struct s2io_nic *sp = (struct s2io_nic *)data;
4362 struct net_device *dev = sp->dev;
4364 s2io_handle_errors(dev);
4365 mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
4368 static int s2io_chk_rx_buffers(struct s2io_nic *sp, int rng_n)
4370 int rxb_size, level;
4373 rxb_size = atomic_read(&sp->rx_bufs_left[rng_n]);
4374 level = rx_buffer_level(sp, rxb_size, rng_n);
4376 if ((level == PANIC) && (!TASKLET_IN_USE)) {
4378 DBG_PRINT(INTR_DBG, "%s: Rx BD hit ", __FUNCTION__);
4379 DBG_PRINT(INTR_DBG, "PANIC levels\n");
4380 if ((ret = fill_rx_buffers(sp, rng_n)) == -ENOMEM) {
4381 DBG_PRINT(INFO_DBG, "Out of memory in %s",
4383 clear_bit(0, (&sp->tasklet_status));
4386 clear_bit(0, (&sp->tasklet_status));
4387 } else if (level == LOW)
4388 tasklet_schedule(&sp->task);
4390 } else if (fill_rx_buffers(sp, rng_n) == -ENOMEM) {
4391 DBG_PRINT(INFO_DBG, "%s:Out of memory", sp->dev->name);
4392 DBG_PRINT(INFO_DBG, " in Rx Intr!!\n");
4397 static irqreturn_t s2io_msix_ring_handle(int irq, void *dev_id)
4399 struct ring_info *ring = (struct ring_info *)dev_id;
4400 struct s2io_nic *sp = ring->nic;
4402 if (!is_s2io_card_up(sp))
4405 rx_intr_handler(ring);
4406 s2io_chk_rx_buffers(sp, ring->ring_no);
4411 static irqreturn_t s2io_msix_fifo_handle(int irq, void *dev_id)
4413 struct fifo_info *fifo = (struct fifo_info *)dev_id;
4414 struct s2io_nic *sp = fifo->nic;
4416 if (!is_s2io_card_up(sp))
4419 tx_intr_handler(fifo);
4422 static void s2io_txpic_intr_handle(struct s2io_nic *sp)
4424 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4427 val64 = readq(&bar0->pic_int_status);
4428 if (val64 & PIC_INT_GPIO) {
4429 val64 = readq(&bar0->gpio_int_reg);
4430 if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
4431 (val64 & GPIO_INT_REG_LINK_UP)) {
4433 * This is unstable state so clear both up/down
4434 * interrupt and adapter to re-evaluate the link state.
4436 val64 |= GPIO_INT_REG_LINK_DOWN;
4437 val64 |= GPIO_INT_REG_LINK_UP;
4438 writeq(val64, &bar0->gpio_int_reg);
4439 val64 = readq(&bar0->gpio_int_mask);
4440 val64 &= ~(GPIO_INT_MASK_LINK_UP |
4441 GPIO_INT_MASK_LINK_DOWN);
4442 writeq(val64, &bar0->gpio_int_mask);
4444 else if (val64 & GPIO_INT_REG_LINK_UP) {
4445 val64 = readq(&bar0->adapter_status);
4446 /* Enable Adapter */
4447 val64 = readq(&bar0->adapter_control);
4448 val64 |= ADAPTER_CNTL_EN;
4449 writeq(val64, &bar0->adapter_control);
4450 val64 |= ADAPTER_LED_ON;
4451 writeq(val64, &bar0->adapter_control);
4452 if (!sp->device_enabled_once)
4453 sp->device_enabled_once = 1;
4455 s2io_link(sp, LINK_UP);
4457 * unmask link down interrupt and mask link-up
4460 val64 = readq(&bar0->gpio_int_mask);
4461 val64 &= ~GPIO_INT_MASK_LINK_DOWN;
4462 val64 |= GPIO_INT_MASK_LINK_UP;
4463 writeq(val64, &bar0->gpio_int_mask);
4465 }else if (val64 & GPIO_INT_REG_LINK_DOWN) {
4466 val64 = readq(&bar0->adapter_status);
4467 s2io_link(sp, LINK_DOWN);
4468 /* Link is down so unmaks link up interrupt */
4469 val64 = readq(&bar0->gpio_int_mask);
4470 val64 &= ~GPIO_INT_MASK_LINK_UP;
4471 val64 |= GPIO_INT_MASK_LINK_DOWN;
4472 writeq(val64, &bar0->gpio_int_mask);
4475 val64 = readq(&bar0->adapter_control);
4476 val64 = val64 &(~ADAPTER_LED_ON);
4477 writeq(val64, &bar0->adapter_control);
4480 val64 = readq(&bar0->gpio_int_mask);
4484 * do_s2io_chk_alarm_bit - Check for alarm and incrment the counter
4485 * @value: alarm bits
4486 * @addr: address value
4487 * @cnt: counter variable
4488 * Description: Check for alarm and increment the counter
4490 * 1 - if alarm bit set
4491 * 0 - if alarm bit is not set
4493 static int do_s2io_chk_alarm_bit(u64 value, void __iomem * addr,
4494 unsigned long long *cnt)
4497 val64 = readq(addr);
4498 if ( val64 & value ) {
4499 writeq(val64, addr);
4508 * s2io_handle_errors - Xframe error indication handler
4509 * @nic: device private variable
4510 * Description: Handle alarms such as loss of link, single or
4511 * double ECC errors, critical and serious errors.
4515 static void s2io_handle_errors(void * dev_id)
4517 struct net_device *dev = (struct net_device *) dev_id;
4518 struct s2io_nic *sp = dev->priv;
4519 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4520 u64 temp64 = 0,val64=0;
4523 struct swStat *sw_stat = &sp->mac_control.stats_info->sw_stat;
4524 struct xpakStat *stats = &sp->mac_control.stats_info->xpak_stat;
4526 if (!is_s2io_card_up(sp))
4529 if (pci_channel_offline(sp->pdev))
4532 memset(&sw_stat->ring_full_cnt, 0,
4533 sizeof(sw_stat->ring_full_cnt));
4535 /* Handling the XPAK counters update */
4536 if(stats->xpak_timer_count < 72000) {
4537 /* waiting for an hour */
4538 stats->xpak_timer_count++;
4540 s2io_updt_xpak_counter(dev);
4541 /* reset the count to zero */
4542 stats->xpak_timer_count = 0;
4545 /* Handling link status change error Intr */
4546 if (s2io_link_fault_indication(sp) == MAC_RMAC_ERR_TIMER) {
4547 val64 = readq(&bar0->mac_rmac_err_reg);
4548 writeq(val64, &bar0->mac_rmac_err_reg);
4549 if (val64 & RMAC_LINK_STATE_CHANGE_INT)
4550 schedule_work(&sp->set_link_task);
4553 /* In case of a serious error, the device will be Reset. */
4554 if (do_s2io_chk_alarm_bit(SERR_SOURCE_ANY, &bar0->serr_source,
4555 &sw_stat->serious_err_cnt))
4558 /* Check for data parity error */
4559 if (do_s2io_chk_alarm_bit(GPIO_INT_REG_DP_ERR_INT, &bar0->gpio_int_reg,
4560 &sw_stat->parity_err_cnt))
4563 /* Check for ring full counter */
4564 if (sp->device_type == XFRAME_II_DEVICE) {
4565 val64 = readq(&bar0->ring_bump_counter1);
4566 for (i=0; i<4; i++) {
4567 temp64 = ( val64 & vBIT(0xFFFF,(i*16),16));
4568 temp64 >>= 64 - ((i+1)*16);
4569 sw_stat->ring_full_cnt[i] += temp64;
4572 val64 = readq(&bar0->ring_bump_counter2);
4573 for (i=0; i<4; i++) {
4574 temp64 = ( val64 & vBIT(0xFFFF,(i*16),16));
4575 temp64 >>= 64 - ((i+1)*16);
4576 sw_stat->ring_full_cnt[i+4] += temp64;
4580 val64 = readq(&bar0->txdma_int_status);
4581 /*check for pfc_err*/
4582 if (val64 & TXDMA_PFC_INT) {
4583 if (do_s2io_chk_alarm_bit(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM|
4584 PFC_MISC_0_ERR | PFC_MISC_1_ERR|
4585 PFC_PCIX_ERR, &bar0->pfc_err_reg,
4586 &sw_stat->pfc_err_cnt))
4588 do_s2io_chk_alarm_bit(PFC_ECC_SG_ERR, &bar0->pfc_err_reg,
4589 &sw_stat->pfc_err_cnt);
4592 /*check for tda_err*/
4593 if (val64 & TXDMA_TDA_INT) {
4594 if(do_s2io_chk_alarm_bit(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
4595 TDA_SM1_ERR_ALARM, &bar0->tda_err_reg,
4596 &sw_stat->tda_err_cnt))
4598 do_s2io_chk_alarm_bit(TDA_Fn_ECC_SG_ERR | TDA_PCIX_ERR,
4599 &bar0->tda_err_reg, &sw_stat->tda_err_cnt);
4601 /*check for pcc_err*/
4602 if (val64 & TXDMA_PCC_INT) {
4603 if (do_s2io_chk_alarm_bit(PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM
4604 | PCC_N_SERR | PCC_6_COF_OV_ERR
4605 | PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR
4606 | PCC_7_LSO_OV_ERR | PCC_FB_ECC_DB_ERR
4607 | PCC_TXB_ECC_DB_ERR, &bar0->pcc_err_reg,
4608 &sw_stat->pcc_err_cnt))
4610 do_s2io_chk_alarm_bit(PCC_FB_ECC_SG_ERR | PCC_TXB_ECC_SG_ERR,
4611 &bar0->pcc_err_reg, &sw_stat->pcc_err_cnt);
4614 /*check for tti_err*/
4615 if (val64 & TXDMA_TTI_INT) {
4616 if (do_s2io_chk_alarm_bit(TTI_SM_ERR_ALARM, &bar0->tti_err_reg,
4617 &sw_stat->tti_err_cnt))
4619 do_s2io_chk_alarm_bit(TTI_ECC_SG_ERR | TTI_ECC_DB_ERR,
4620 &bar0->tti_err_reg, &sw_stat->tti_err_cnt);
4623 /*check for lso_err*/
4624 if (val64 & TXDMA_LSO_INT) {
4625 if (do_s2io_chk_alarm_bit(LSO6_ABORT | LSO7_ABORT
4626 | LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM,
4627 &bar0->lso_err_reg, &sw_stat->lso_err_cnt))
4629 do_s2io_chk_alarm_bit(LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
4630 &bar0->lso_err_reg, &sw_stat->lso_err_cnt);
4633 /*check for tpa_err*/
4634 if (val64 & TXDMA_TPA_INT) {
4635 if (do_s2io_chk_alarm_bit(TPA_SM_ERR_ALARM, &bar0->tpa_err_reg,
4636 &sw_stat->tpa_err_cnt))
4638 do_s2io_chk_alarm_bit(TPA_TX_FRM_DROP, &bar0->tpa_err_reg,
4639 &sw_stat->tpa_err_cnt);
4642 /*check for sm_err*/
4643 if (val64 & TXDMA_SM_INT) {
4644 if (do_s2io_chk_alarm_bit(SM_SM_ERR_ALARM, &bar0->sm_err_reg,
4645 &sw_stat->sm_err_cnt))
4649 val64 = readq(&bar0->mac_int_status);
4650 if (val64 & MAC_INT_STATUS_TMAC_INT) {
4651 if (do_s2io_chk_alarm_bit(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR,
4652 &bar0->mac_tmac_err_reg,
4653 &sw_stat->mac_tmac_err_cnt))
4655 do_s2io_chk_alarm_bit(TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR
4656 | TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
4657 &bar0->mac_tmac_err_reg,
4658 &sw_stat->mac_tmac_err_cnt);
4661 val64 = readq(&bar0->xgxs_int_status);
4662 if (val64 & XGXS_INT_STATUS_TXGXS) {
4663 if (do_s2io_chk_alarm_bit(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR,
4664 &bar0->xgxs_txgxs_err_reg,
4665 &sw_stat->xgxs_txgxs_err_cnt))
4667 do_s2io_chk_alarm_bit(TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
4668 &bar0->xgxs_txgxs_err_reg,
4669 &sw_stat->xgxs_txgxs_err_cnt);
4672 val64 = readq(&bar0->rxdma_int_status);
4673 if (val64 & RXDMA_INT_RC_INT_M) {
4674 if (do_s2io_chk_alarm_bit(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR
4675 | RC_PRCn_SM_ERR_ALARM |RC_FTC_SM_ERR_ALARM,
4676 &bar0->rc_err_reg, &sw_stat->rc_err_cnt))
4678 do_s2io_chk_alarm_bit(RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR
4679 | RC_RDA_FAIL_WR_Rn, &bar0->rc_err_reg,
4680 &sw_stat->rc_err_cnt);
4681 if (do_s2io_chk_alarm_bit(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn
4682 | PRC_PCI_AB_F_WR_Rn, &bar0->prc_pcix_err_reg,
4683 &sw_stat->prc_pcix_err_cnt))
4685 do_s2io_chk_alarm_bit(PRC_PCI_DP_RD_Rn | PRC_PCI_DP_WR_Rn
4686 | PRC_PCI_DP_F_WR_Rn, &bar0->prc_pcix_err_reg,
4687 &sw_stat->prc_pcix_err_cnt);
4690 if (val64 & RXDMA_INT_RPA_INT_M) {
4691 if (do_s2io_chk_alarm_bit(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR,
4692 &bar0->rpa_err_reg, &sw_stat->rpa_err_cnt))
4694 do_s2io_chk_alarm_bit(RPA_ECC_SG_ERR | RPA_ECC_DB_ERR,
4695 &bar0->rpa_err_reg, &sw_stat->rpa_err_cnt);
4698 if (val64 & RXDMA_INT_RDA_INT_M) {
4699 if (do_s2io_chk_alarm_bit(RDA_RXDn_ECC_DB_ERR
4700 | RDA_FRM_ECC_DB_N_AERR | RDA_SM1_ERR_ALARM
4701 | RDA_SM0_ERR_ALARM | RDA_RXD_ECC_DB_SERR,
4702 &bar0->rda_err_reg, &sw_stat->rda_err_cnt))
4704 do_s2io_chk_alarm_bit(RDA_RXDn_ECC_SG_ERR | RDA_FRM_ECC_SG_ERR
4705 | RDA_MISC_ERR | RDA_PCIX_ERR,
4706 &bar0->rda_err_reg, &sw_stat->rda_err_cnt);
4709 if (val64 & RXDMA_INT_RTI_INT_M) {
4710 if (do_s2io_chk_alarm_bit(RTI_SM_ERR_ALARM, &bar0->rti_err_reg,
4711 &sw_stat->rti_err_cnt))
4713 do_s2io_chk_alarm_bit(RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
4714 &bar0->rti_err_reg, &sw_stat->rti_err_cnt);
4717 val64 = readq(&bar0->mac_int_status);
4718 if (val64 & MAC_INT_STATUS_RMAC_INT) {
4719 if (do_s2io_chk_alarm_bit(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR,
4720 &bar0->mac_rmac_err_reg,
4721 &sw_stat->mac_rmac_err_cnt))
4723 do_s2io_chk_alarm_bit(RMAC_UNUSED_INT|RMAC_SINGLE_ECC_ERR|
4724 RMAC_DOUBLE_ECC_ERR, &bar0->mac_rmac_err_reg,
4725 &sw_stat->mac_rmac_err_cnt);
4728 val64 = readq(&bar0->xgxs_int_status);
4729 if (val64 & XGXS_INT_STATUS_RXGXS) {
4730 if (do_s2io_chk_alarm_bit(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR,
4731 &bar0->xgxs_rxgxs_err_reg,
4732 &sw_stat->xgxs_rxgxs_err_cnt))
4736 val64 = readq(&bar0->mc_int_status);
4737 if(val64 & MC_INT_STATUS_MC_INT) {
4738 if (do_s2io_chk_alarm_bit(MC_ERR_REG_SM_ERR, &bar0->mc_err_reg,
4739 &sw_stat->mc_err_cnt))
4742 /* Handling Ecc errors */
4743 if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) {
4744 writeq(val64, &bar0->mc_err_reg);
4745 if (val64 & MC_ERR_REG_ECC_ALL_DBL) {
4746 sw_stat->double_ecc_errs++;
4747 if (sp->device_type != XFRAME_II_DEVICE) {
4749 * Reset XframeI only if critical error
4752 (MC_ERR_REG_MIRI_ECC_DB_ERR_0 |
4753 MC_ERR_REG_MIRI_ECC_DB_ERR_1))
4757 sw_stat->single_ecc_errs++;
4763 s2io_stop_all_tx_queue(sp);
4764 schedule_work(&sp->rst_timer_task);
4765 sw_stat->soft_reset_cnt++;
4770 * s2io_isr - ISR handler of the device .
4771 * @irq: the irq of the device.
4772 * @dev_id: a void pointer to the dev structure of the NIC.
4773 * Description: This function is the ISR handler of the device. It
4774 * identifies the reason for the interrupt and calls the relevant
4775 * service routines. As a contongency measure, this ISR allocates the
4776 * recv buffers, if their numbers are below the panic value which is
4777 * presently set to 25% of the original number of rcv buffers allocated.
4779 * IRQ_HANDLED: will be returned if IRQ was handled by this routine
4780 * IRQ_NONE: will be returned if interrupt is not from our device
4782 static irqreturn_t s2io_isr(int irq, void *dev_id)
4784 struct net_device *dev = (struct net_device *) dev_id;
4785 struct s2io_nic *sp = dev->priv;
4786 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4789 struct mac_info *mac_control;
4790 struct config_param *config;
4792 /* Pretend we handled any irq's from a disconnected card */
4793 if (pci_channel_offline(sp->pdev))
4796 if (!is_s2io_card_up(sp))
4799 mac_control = &sp->mac_control;
4800 config = &sp->config;
4803 * Identify the cause for interrupt and call the appropriate
4804 * interrupt handler. Causes for the interrupt could be;
4809 reason = readq(&bar0->general_int_status);
4811 if (unlikely(reason == S2IO_MINUS_ONE) ) {
4812 /* Nothing much can be done. Get out */
4816 if (reason & (GEN_INTR_RXTRAFFIC |
4817 GEN_INTR_TXTRAFFIC | GEN_INTR_TXPIC))
4819 writeq(S2IO_MINUS_ONE, &bar0->general_int_mask);
4822 if (reason & GEN_INTR_RXTRAFFIC) {
4823 if (likely(netif_rx_schedule_prep(dev,
4825 __netif_rx_schedule(dev, &sp->napi);
4826 writeq(S2IO_MINUS_ONE,
4827 &bar0->rx_traffic_mask);
4829 writeq(S2IO_MINUS_ONE,
4830 &bar0->rx_traffic_int);
4834 * rx_traffic_int reg is an R1 register, writing all 1's
4835 * will ensure that the actual interrupt causing bit
4836 * get's cleared and hence a read can be avoided.
4838 if (reason & GEN_INTR_RXTRAFFIC)
4839 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
4841 for (i = 0; i < config->rx_ring_num; i++)
4842 rx_intr_handler(&mac_control->rings[i]);
4846 * tx_traffic_int reg is an R1 register, writing all 1's
4847 * will ensure that the actual interrupt causing bit get's
4848 * cleared and hence a read can be avoided.
4850 if (reason & GEN_INTR_TXTRAFFIC)
4851 writeq(S2IO_MINUS_ONE, &bar0->tx_traffic_int);
4853 for (i = 0; i < config->tx_fifo_num; i++)
4854 tx_intr_handler(&mac_control->fifos[i]);
4856 if (reason & GEN_INTR_TXPIC)
4857 s2io_txpic_intr_handle(sp);
4860 * Reallocate the buffers from the interrupt handler itself.
4862 if (!config->napi) {
4863 for (i = 0; i < config->rx_ring_num; i++)
4864 s2io_chk_rx_buffers(sp, i);
4866 writeq(sp->general_int_mask, &bar0->general_int_mask);
4867 readl(&bar0->general_int_status);
4873 /* The interrupt was not raised by us */
4883 static void s2io_updt_stats(struct s2io_nic *sp)
4885 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4889 if (is_s2io_card_up(sp)) {
4890 /* Apprx 30us on a 133 MHz bus */
4891 val64 = SET_UPDT_CLICKS(10) |
4892 STAT_CFG_ONE_SHOT_EN | STAT_CFG_STAT_EN;
4893 writeq(val64, &bar0->stat_cfg);
4896 val64 = readq(&bar0->stat_cfg);
4897 if (!(val64 & s2BIT(0)))
4901 break; /* Updt failed */
4907 * s2io_get_stats - Updates the device statistics structure.
4908 * @dev : pointer to the device structure.
4910 * This function updates the device statistics structure in the s2io_nic
4911 * structure and returns a pointer to the same.
4913 * pointer to the updated net_device_stats structure.
4916 static struct net_device_stats *s2io_get_stats(struct net_device *dev)
4918 struct s2io_nic *sp = dev->priv;
4919 struct mac_info *mac_control;
4920 struct config_param *config;
4923 mac_control = &sp->mac_control;
4924 config = &sp->config;
4926 /* Configure Stats for immediate updt */
4927 s2io_updt_stats(sp);
4929 sp->stats.tx_packets =
4930 le32_to_cpu(mac_control->stats_info->tmac_frms);
4931 sp->stats.tx_errors =
4932 le32_to_cpu(mac_control->stats_info->tmac_any_err_frms);
4933 sp->stats.rx_errors =
4934 le64_to_cpu(mac_control->stats_info->rmac_drop_frms);
4935 sp->stats.multicast =
4936 le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms);
4937 sp->stats.rx_length_errors =
4938 le64_to_cpu(mac_control->stats_info->rmac_long_frms);
4940 return (&sp->stats);
4944 * s2io_set_multicast - entry point for multicast address enable/disable.
4945 * @dev : pointer to the device structure
4947 * This function is a driver entry point which gets called by the kernel
4948 * whenever multicast addresses must be enabled/disabled. This also gets
4949 * called to set/reset promiscuous mode. Depending on the deivce flag, we
4950 * determine, if multicast address must be enabled or if promiscuous mode
4951 * is to be disabled etc.
4956 static void s2io_set_multicast(struct net_device *dev)
4959 struct dev_mc_list *mclist;
4960 struct s2io_nic *sp = dev->priv;
4961 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4962 u64 val64 = 0, multi_mac = 0x010203040506ULL, mask =
4964 u64 dis_addr = S2IO_DISABLE_MAC_ENTRY, mac_addr = 0;
4966 struct config_param *config = &sp->config;
4968 if ((dev->flags & IFF_ALLMULTI) && (!sp->m_cast_flg)) {
4969 /* Enable all Multicast addresses */
4970 writeq(RMAC_ADDR_DATA0_MEM_ADDR(multi_mac),
4971 &bar0->rmac_addr_data0_mem);
4972 writeq(RMAC_ADDR_DATA1_MEM_MASK(mask),
4973 &bar0->rmac_addr_data1_mem);
4974 val64 = RMAC_ADDR_CMD_MEM_WE |
4975 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4976 RMAC_ADDR_CMD_MEM_OFFSET(config->max_mc_addr - 1);
4977 writeq(val64, &bar0->rmac_addr_cmd_mem);
4978 /* Wait till command completes */
4979 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4980 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4984 sp->all_multi_pos = config->max_mc_addr - 1;
4985 } else if ((dev->flags & IFF_ALLMULTI) && (sp->m_cast_flg)) {
4986 /* Disable all Multicast addresses */
4987 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
4988 &bar0->rmac_addr_data0_mem);
4989 writeq(RMAC_ADDR_DATA1_MEM_MASK(0x0),
4990 &bar0->rmac_addr_data1_mem);
4991 val64 = RMAC_ADDR_CMD_MEM_WE |
4992 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4993 RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
4994 writeq(val64, &bar0->rmac_addr_cmd_mem);
4995 /* Wait till command completes */
4996 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4997 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5001 sp->all_multi_pos = 0;
5004 if ((dev->flags & IFF_PROMISC) && (!sp->promisc_flg)) {
5005 /* Put the NIC into promiscuous mode */
5006 add = &bar0->mac_cfg;
5007 val64 = readq(&bar0->mac_cfg);
5008 val64 |= MAC_CFG_RMAC_PROM_ENABLE;
5010 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5011 writel((u32) val64, add);
5012 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5013 writel((u32) (val64 >> 32), (add + 4));
5015 if (vlan_tag_strip != 1) {
5016 val64 = readq(&bar0->rx_pa_cfg);
5017 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
5018 writeq(val64, &bar0->rx_pa_cfg);
5019 vlan_strip_flag = 0;
5022 val64 = readq(&bar0->mac_cfg);
5023 sp->promisc_flg = 1;
5024 DBG_PRINT(INFO_DBG, "%s: entered promiscuous mode\n",
5026 } else if (!(dev->flags & IFF_PROMISC) && (sp->promisc_flg)) {
5027 /* Remove the NIC from promiscuous mode */
5028 add = &bar0->mac_cfg;
5029 val64 = readq(&bar0->mac_cfg);
5030 val64 &= ~MAC_CFG_RMAC_PROM_ENABLE;
5032 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5033 writel((u32) val64, add);
5034 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5035 writel((u32) (val64 >> 32), (add + 4));
5037 if (vlan_tag_strip != 0) {
5038 val64 = readq(&bar0->rx_pa_cfg);
5039 val64 |= RX_PA_CFG_STRIP_VLAN_TAG;
5040 writeq(val64, &bar0->rx_pa_cfg);
5041 vlan_strip_flag = 1;
5044 val64 = readq(&bar0->mac_cfg);
5045 sp->promisc_flg = 0;
5046 DBG_PRINT(INFO_DBG, "%s: left promiscuous mode\n",
5050 /* Update individual M_CAST address list */
5051 if ((!sp->m_cast_flg) && dev->mc_count) {
5053 (config->max_mc_addr - config->max_mac_addr)) {
5054 DBG_PRINT(ERR_DBG, "%s: No more Rx filters ",
5056 DBG_PRINT(ERR_DBG, "can be added, please enable ");
5057 DBG_PRINT(ERR_DBG, "ALL_MULTI instead\n");
5061 prev_cnt = sp->mc_addr_count;
5062 sp->mc_addr_count = dev->mc_count;
5064 /* Clear out the previous list of Mc in the H/W. */
5065 for (i = 0; i < prev_cnt; i++) {
5066 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
5067 &bar0->rmac_addr_data0_mem);
5068 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
5069 &bar0->rmac_addr_data1_mem);
5070 val64 = RMAC_ADDR_CMD_MEM_WE |
5071 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5072 RMAC_ADDR_CMD_MEM_OFFSET
5073 (config->mc_start_offset + i);
5074 writeq(val64, &bar0->rmac_addr_cmd_mem);
5076 /* Wait for command completes */
5077 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5078 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5080 DBG_PRINT(ERR_DBG, "%s: Adding ",
5082 DBG_PRINT(ERR_DBG, "Multicasts failed\n");
5087 /* Create the new Rx filter list and update the same in H/W. */
5088 for (i = 0, mclist = dev->mc_list; i < dev->mc_count;
5089 i++, mclist = mclist->next) {
5090 memcpy(sp->usr_addrs[i].addr, mclist->dmi_addr,
5093 for (j = 0; j < ETH_ALEN; j++) {
5094 mac_addr |= mclist->dmi_addr[j];
5098 writeq(RMAC_ADDR_DATA0_MEM_ADDR(mac_addr),
5099 &bar0->rmac_addr_data0_mem);
5100 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
5101 &bar0->rmac_addr_data1_mem);
5102 val64 = RMAC_ADDR_CMD_MEM_WE |
5103 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5104 RMAC_ADDR_CMD_MEM_OFFSET
5105 (i + config->mc_start_offset);
5106 writeq(val64, &bar0->rmac_addr_cmd_mem);
5108 /* Wait for command completes */
5109 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5110 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5112 DBG_PRINT(ERR_DBG, "%s: Adding ",
5114 DBG_PRINT(ERR_DBG, "Multicasts failed\n");
5121 /* read from CAM unicast & multicast addresses and store it in
5122 * def_mac_addr structure
5124 void do_s2io_store_unicast_mc(struct s2io_nic *sp)
5128 struct config_param *config = &sp->config;
5130 /* store unicast & multicast mac addresses */
5131 for (offset = 0; offset < config->max_mc_addr; offset++) {
5132 mac_addr = do_s2io_read_unicast_mc(sp, offset);
5133 /* if read fails disable the entry */
5134 if (mac_addr == FAILURE)
5135 mac_addr = S2IO_DISABLE_MAC_ENTRY;
5136 do_s2io_copy_mac_addr(sp, offset, mac_addr);
5140 /* restore unicast & multicast MAC to CAM from def_mac_addr structure */
5141 static void do_s2io_restore_unicast_mc(struct s2io_nic *sp)
5144 struct config_param *config = &sp->config;
5145 /* restore unicast mac address */
5146 for (offset = 0; offset < config->max_mac_addr; offset++)
5147 do_s2io_prog_unicast(sp->dev,
5148 sp->def_mac_addr[offset].mac_addr);
5150 /* restore multicast mac address */
5151 for (offset = config->mc_start_offset;
5152 offset < config->max_mc_addr; offset++)
5153 do_s2io_add_mc(sp, sp->def_mac_addr[offset].mac_addr);
5156 /* add a multicast MAC address to CAM */
5157 static int do_s2io_add_mc(struct s2io_nic *sp, u8 *addr)
5161 struct config_param *config = &sp->config;
5163 for (i = 0; i < ETH_ALEN; i++) {
5165 mac_addr |= addr[i];
5167 if ((0ULL == mac_addr) || (mac_addr == S2IO_DISABLE_MAC_ENTRY))
5170 /* check if the multicast mac already preset in CAM */
5171 for (i = config->mc_start_offset; i < config->max_mc_addr; i++) {
5173 tmp64 = do_s2io_read_unicast_mc(sp, i);
5174 if (tmp64 == S2IO_DISABLE_MAC_ENTRY) /* CAM entry is empty */
5177 if (tmp64 == mac_addr)
5180 if (i == config->max_mc_addr) {
5182 "CAM full no space left for multicast MAC\n");
5185 /* Update the internal structure with this new mac address */
5186 do_s2io_copy_mac_addr(sp, i, mac_addr);
5188 return (do_s2io_add_mac(sp, mac_addr, i));
5191 /* add MAC address to CAM */
5192 static int do_s2io_add_mac(struct s2io_nic *sp, u64 addr, int off)
5195 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5197 writeq(RMAC_ADDR_DATA0_MEM_ADDR(addr),
5198 &bar0->rmac_addr_data0_mem);
5201 RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5202 RMAC_ADDR_CMD_MEM_OFFSET(off);
5203 writeq(val64, &bar0->rmac_addr_cmd_mem);
5205 /* Wait till command completes */
5206 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5207 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5209 DBG_PRINT(INFO_DBG, "do_s2io_add_mac failed\n");
5214 /* deletes a specified unicast/multicast mac entry from CAM */
5215 static int do_s2io_delete_unicast_mc(struct s2io_nic *sp, u64 addr)
5218 u64 dis_addr = S2IO_DISABLE_MAC_ENTRY, tmp64;
5219 struct config_param *config = &sp->config;
5222 offset < config->max_mc_addr; offset++) {
5223 tmp64 = do_s2io_read_unicast_mc(sp, offset);
5224 if (tmp64 == addr) {
5225 /* disable the entry by writing 0xffffffffffffULL */
5226 if (do_s2io_add_mac(sp, dis_addr, offset) == FAILURE)
5228 /* store the new mac list from CAM */
5229 do_s2io_store_unicast_mc(sp);
5233 DBG_PRINT(ERR_DBG, "MAC address 0x%llx not found in CAM\n",
5234 (unsigned long long)addr);
5238 /* read mac entries from CAM */
5239 static u64 do_s2io_read_unicast_mc(struct s2io_nic *sp, int offset)
5241 u64 tmp64 = 0xffffffffffff0000ULL, val64;
5242 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5246 RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5247 RMAC_ADDR_CMD_MEM_OFFSET(offset);
5248 writeq(val64, &bar0->rmac_addr_cmd_mem);
5250 /* Wait till command completes */
5251 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5252 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5254 DBG_PRINT(INFO_DBG, "do_s2io_read_unicast_mc failed\n");
5257 tmp64 = readq(&bar0->rmac_addr_data0_mem);
5258 return (tmp64 >> 16);
5262 * s2io_set_mac_addr driver entry point
5265 static int s2io_set_mac_addr(struct net_device *dev, void *p)
5267 struct sockaddr *addr = p;
5269 if (!is_valid_ether_addr(addr->sa_data))
5272 memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
5274 /* store the MAC address in CAM */
5275 return (do_s2io_prog_unicast(dev, dev->dev_addr));
5278 * do_s2io_prog_unicast - Programs the Xframe mac address
5279 * @dev : pointer to the device structure.
5280 * @addr: a uchar pointer to the new mac address which is to be set.
5281 * Description : This procedure will program the Xframe to receive
5282 * frames with new Mac Address
5283 * Return value: SUCCESS on success and an appropriate (-)ve integer
5284 * as defined in errno.h file on failure.
5287 static int do_s2io_prog_unicast(struct net_device *dev, u8 *addr)
5289 struct s2io_nic *sp = dev->priv;
5290 register u64 mac_addr = 0, perm_addr = 0;
5293 struct config_param *config = &sp->config;
5296 * Set the new MAC address as the new unicast filter and reflect this
5297 * change on the device address registered with the OS. It will be
5300 for (i = 0; i < ETH_ALEN; i++) {
5302 mac_addr |= addr[i];
5304 perm_addr |= sp->def_mac_addr[0].mac_addr[i];
5307 /* check if the dev_addr is different than perm_addr */
5308 if (mac_addr == perm_addr)
5311 /* check if the mac already preset in CAM */
5312 for (i = 1; i < config->max_mac_addr; i++) {
5313 tmp64 = do_s2io_read_unicast_mc(sp, i);
5314 if (tmp64 == S2IO_DISABLE_MAC_ENTRY) /* CAM entry is empty */
5317 if (tmp64 == mac_addr) {
5319 "MAC addr:0x%llx already present in CAM\n",
5320 (unsigned long long)mac_addr);
5324 if (i == config->max_mac_addr) {
5325 DBG_PRINT(ERR_DBG, "CAM full no space left for Unicast MAC\n");
5328 /* Update the internal structure with this new mac address */
5329 do_s2io_copy_mac_addr(sp, i, mac_addr);
5330 return (do_s2io_add_mac(sp, mac_addr, i));
5334 * s2io_ethtool_sset - Sets different link parameters.
5335 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5336 * @info: pointer to the structure with parameters given by ethtool to set
5339 * The function sets different link parameters provided by the user onto
5345 static int s2io_ethtool_sset(struct net_device *dev,
5346 struct ethtool_cmd *info)
5348 struct s2io_nic *sp = dev->priv;
5349 if ((info->autoneg == AUTONEG_ENABLE) ||
5350 (info->speed != SPEED_10000) || (info->duplex != DUPLEX_FULL))
5353 s2io_close(sp->dev);
5361 * s2io_ethtol_gset - Return link specific information.
5362 * @sp : private member of the device structure, pointer to the
5363 * s2io_nic structure.
5364 * @info : pointer to the structure with parameters given by ethtool
5365 * to return link information.
5367 * Returns link specific information like speed, duplex etc.. to ethtool.
5369 * return 0 on success.
5372 static int s2io_ethtool_gset(struct net_device *dev, struct ethtool_cmd *info)
5374 struct s2io_nic *sp = dev->priv;
5375 info->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
5376 info->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
5377 info->port = PORT_FIBRE;
5379 /* info->transceiver */
5380 info->transceiver = XCVR_EXTERNAL;
5382 if (netif_carrier_ok(sp->dev)) {
5383 info->speed = 10000;
5384 info->duplex = DUPLEX_FULL;
5390 info->autoneg = AUTONEG_DISABLE;
5395 * s2io_ethtool_gdrvinfo - Returns driver specific information.
5396 * @sp : private member of the device structure, which is a pointer to the
5397 * s2io_nic structure.
5398 * @info : pointer to the structure with parameters given by ethtool to
5399 * return driver information.
5401 * Returns driver specefic information like name, version etc.. to ethtool.
5406 static void s2io_ethtool_gdrvinfo(struct net_device *dev,
5407 struct ethtool_drvinfo *info)
5409 struct s2io_nic *sp = dev->priv;
5411 strncpy(info->driver, s2io_driver_name, sizeof(info->driver));
5412 strncpy(info->version, s2io_driver_version, sizeof(info->version));
5413 strncpy(info->fw_version, "", sizeof(info->fw_version));
5414 strncpy(info->bus_info, pci_name(sp->pdev), sizeof(info->bus_info));
5415 info->regdump_len = XENA_REG_SPACE;
5416 info->eedump_len = XENA_EEPROM_SPACE;
5420 * s2io_ethtool_gregs - dumps the entire space of Xfame into the buffer.
5421 * @sp: private member of the device structure, which is a pointer to the
5422 * s2io_nic structure.
5423 * @regs : pointer to the structure with parameters given by ethtool for
5424 * dumping the registers.
5425 * @reg_space: The input argumnet into which all the registers are dumped.
5427 * Dumps the entire register space of xFrame NIC into the user given
5433 static void s2io_ethtool_gregs(struct net_device *dev,
5434 struct ethtool_regs *regs, void *space)
5438 u8 *reg_space = (u8 *) space;
5439 struct s2io_nic *sp = dev->priv;
5441 regs->len = XENA_REG_SPACE;
5442 regs->version = sp->pdev->subsystem_device;
5444 for (i = 0; i < regs->len; i += 8) {
5445 reg = readq(sp->bar0 + i);
5446 memcpy((reg_space + i), ®, 8);
5451 * s2io_phy_id - timer function that alternates adapter LED.
5452 * @data : address of the private member of the device structure, which
5453 * is a pointer to the s2io_nic structure, provided as an u32.
5454 * Description: This is actually the timer function that alternates the
5455 * adapter LED bit of the adapter control bit to set/reset every time on
5456 * invocation. The timer is set for 1/2 a second, hence tha NIC blinks
5457 * once every second.
5459 static void s2io_phy_id(unsigned long data)
5461 struct s2io_nic *sp = (struct s2io_nic *) data;
5462 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5466 subid = sp->pdev->subsystem_device;
5467 if ((sp->device_type == XFRAME_II_DEVICE) ||
5468 ((subid & 0xFF) >= 0x07)) {
5469 val64 = readq(&bar0->gpio_control);
5470 val64 ^= GPIO_CTRL_GPIO_0;
5471 writeq(val64, &bar0->gpio_control);
5473 val64 = readq(&bar0->adapter_control);
5474 val64 ^= ADAPTER_LED_ON;
5475 writeq(val64, &bar0->adapter_control);
5478 mod_timer(&sp->id_timer, jiffies + HZ / 2);
5482 * s2io_ethtool_idnic - To physically identify the nic on the system.
5483 * @sp : private member of the device structure, which is a pointer to the
5484 * s2io_nic structure.
5485 * @id : pointer to the structure with identification parameters given by
5487 * Description: Used to physically identify the NIC on the system.
5488 * The Link LED will blink for a time specified by the user for
5490 * NOTE: The Link has to be Up to be able to blink the LED. Hence
5491 * identification is possible only if it's link is up.
5493 * int , returns 0 on success
5496 static int s2io_ethtool_idnic(struct net_device *dev, u32 data)
5498 u64 val64 = 0, last_gpio_ctrl_val;
5499 struct s2io_nic *sp = dev->priv;
5500 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5503 subid = sp->pdev->subsystem_device;
5504 last_gpio_ctrl_val = readq(&bar0->gpio_control);
5505 if ((sp->device_type == XFRAME_I_DEVICE) &&
5506 ((subid & 0xFF) < 0x07)) {
5507 val64 = readq(&bar0->adapter_control);
5508 if (!(val64 & ADAPTER_CNTL_EN)) {
5510 "Adapter Link down, cannot blink LED\n");
5514 if (sp->id_timer.function == NULL) {
5515 init_timer(&sp->id_timer);
5516 sp->id_timer.function = s2io_phy_id;
5517 sp->id_timer.data = (unsigned long) sp;
5519 mod_timer(&sp->id_timer, jiffies);
5521 msleep_interruptible(data * HZ);
5523 msleep_interruptible(MAX_FLICKER_TIME);
5524 del_timer_sync(&sp->id_timer);
5526 if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid)) {
5527 writeq(last_gpio_ctrl_val, &bar0->gpio_control);
5528 last_gpio_ctrl_val = readq(&bar0->gpio_control);
5534 static void s2io_ethtool_gringparam(struct net_device *dev,
5535 struct ethtool_ringparam *ering)
5537 struct s2io_nic *sp = dev->priv;
5538 int i,tx_desc_count=0,rx_desc_count=0;
5540 if (sp->rxd_mode == RXD_MODE_1)
5541 ering->rx_max_pending = MAX_RX_DESC_1;
5542 else if (sp->rxd_mode == RXD_MODE_3B)
5543 ering->rx_max_pending = MAX_RX_DESC_2;
5545 ering->tx_max_pending = MAX_TX_DESC;
5546 for (i = 0 ; i < sp->config.tx_fifo_num ; i++)
5547 tx_desc_count += sp->config.tx_cfg[i].fifo_len;
5549 DBG_PRINT(INFO_DBG,"\nmax txds : %d\n",sp->config.max_txds);
5550 ering->tx_pending = tx_desc_count;
5552 for (i = 0 ; i < sp->config.rx_ring_num ; i++)
5553 rx_desc_count += sp->config.rx_cfg[i].num_rxd;
5555 ering->rx_pending = rx_desc_count;
5557 ering->rx_mini_max_pending = 0;
5558 ering->rx_mini_pending = 0;
5559 if(sp->rxd_mode == RXD_MODE_1)
5560 ering->rx_jumbo_max_pending = MAX_RX_DESC_1;
5561 else if (sp->rxd_mode == RXD_MODE_3B)
5562 ering->rx_jumbo_max_pending = MAX_RX_DESC_2;
5563 ering->rx_jumbo_pending = rx_desc_count;
5567 * s2io_ethtool_getpause_data -Pause frame frame generation and reception.
5568 * @sp : private member of the device structure, which is a pointer to the
5569 * s2io_nic structure.
5570 * @ep : pointer to the structure with pause parameters given by ethtool.
5572 * Returns the Pause frame generation and reception capability of the NIC.
5576 static void s2io_ethtool_getpause_data(struct net_device *dev,
5577 struct ethtool_pauseparam *ep)
5580 struct s2io_nic *sp = dev->priv;
5581 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5583 val64 = readq(&bar0->rmac_pause_cfg);
5584 if (val64 & RMAC_PAUSE_GEN_ENABLE)
5585 ep->tx_pause = TRUE;
5586 if (val64 & RMAC_PAUSE_RX_ENABLE)
5587 ep->rx_pause = TRUE;
5588 ep->autoneg = FALSE;
5592 * s2io_ethtool_setpause_data - set/reset pause frame generation.
5593 * @sp : private member of the device structure, which is a pointer to the
5594 * s2io_nic structure.
5595 * @ep : pointer to the structure with pause parameters given by ethtool.
5597 * It can be used to set or reset Pause frame generation or reception
5598 * support of the NIC.
5600 * int, returns 0 on Success
5603 static int s2io_ethtool_setpause_data(struct net_device *dev,
5604 struct ethtool_pauseparam *ep)
5607 struct s2io_nic *sp = dev->priv;
5608 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5610 val64 = readq(&bar0->rmac_pause_cfg);
5612 val64 |= RMAC_PAUSE_GEN_ENABLE;
5614 val64 &= ~RMAC_PAUSE_GEN_ENABLE;
5616 val64 |= RMAC_PAUSE_RX_ENABLE;
5618 val64 &= ~RMAC_PAUSE_RX_ENABLE;
5619 writeq(val64, &bar0->rmac_pause_cfg);
5624 * read_eeprom - reads 4 bytes of data from user given offset.
5625 * @sp : private member of the device structure, which is a pointer to the
5626 * s2io_nic structure.
5627 * @off : offset at which the data must be written
5628 * @data : Its an output parameter where the data read at the given
5631 * Will read 4 bytes of data from the user given offset and return the
5633 * NOTE: Will allow to read only part of the EEPROM visible through the
5636 * -1 on failure and 0 on success.
5639 #define S2IO_DEV_ID 5
5640 static int read_eeprom(struct s2io_nic * sp, int off, u64 * data)
5645 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5647 if (sp->device_type == XFRAME_I_DEVICE) {
5648 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) | I2C_CONTROL_ADDR(off) |
5649 I2C_CONTROL_BYTE_CNT(0x3) | I2C_CONTROL_READ |
5650 I2C_CONTROL_CNTL_START;
5651 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5653 while (exit_cnt < 5) {
5654 val64 = readq(&bar0->i2c_control);
5655 if (I2C_CONTROL_CNTL_END(val64)) {
5656 *data = I2C_CONTROL_GET_DATA(val64);
5665 if (sp->device_type == XFRAME_II_DEVICE) {
5666 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5667 SPI_CONTROL_BYTECNT(0x3) |
5668 SPI_CONTROL_CMD(0x3) | SPI_CONTROL_ADDR(off);
5669 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5670 val64 |= SPI_CONTROL_REQ;
5671 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5672 while (exit_cnt < 5) {
5673 val64 = readq(&bar0->spi_control);
5674 if (val64 & SPI_CONTROL_NACK) {
5677 } else if (val64 & SPI_CONTROL_DONE) {
5678 *data = readq(&bar0->spi_data);
5691 * write_eeprom - actually writes the relevant part of the data value.
5692 * @sp : private member of the device structure, which is a pointer to the
5693 * s2io_nic structure.
5694 * @off : offset at which the data must be written
5695 * @data : The data that is to be written
5696 * @cnt : Number of bytes of the data that are actually to be written into
5697 * the Eeprom. (max of 3)
5699 * Actually writes the relevant part of the data value into the Eeprom
5700 * through the I2C bus.
5702 * 0 on success, -1 on failure.
5705 static int write_eeprom(struct s2io_nic * sp, int off, u64 data, int cnt)
5707 int exit_cnt = 0, ret = -1;
5709 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5711 if (sp->device_type == XFRAME_I_DEVICE) {
5712 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) | I2C_CONTROL_ADDR(off) |
5713 I2C_CONTROL_BYTE_CNT(cnt) | I2C_CONTROL_SET_DATA((u32)data) |
5714 I2C_CONTROL_CNTL_START;
5715 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5717 while (exit_cnt < 5) {
5718 val64 = readq(&bar0->i2c_control);
5719 if (I2C_CONTROL_CNTL_END(val64)) {
5720 if (!(val64 & I2C_CONTROL_NACK))
5729 if (sp->device_type == XFRAME_II_DEVICE) {
5730 int write_cnt = (cnt == 8) ? 0 : cnt;
5731 writeq(SPI_DATA_WRITE(data,(cnt<<3)), &bar0->spi_data);
5733 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5734 SPI_CONTROL_BYTECNT(write_cnt) |
5735 SPI_CONTROL_CMD(0x2) | SPI_CONTROL_ADDR(off);
5736 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5737 val64 |= SPI_CONTROL_REQ;
5738 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5739 while (exit_cnt < 5) {
5740 val64 = readq(&bar0->spi_control);
5741 if (val64 & SPI_CONTROL_NACK) {
5744 } else if (val64 & SPI_CONTROL_DONE) {
5754 static void s2io_vpd_read(struct s2io_nic *nic)
5758 int i=0, cnt, fail = 0;
5759 int vpd_addr = 0x80;
5761 if (nic->device_type == XFRAME_II_DEVICE) {
5762 strcpy(nic->product_name, "Xframe II 10GbE network adapter");
5766 strcpy(nic->product_name, "Xframe I 10GbE network adapter");
5769 strcpy(nic->serial_num, "NOT AVAILABLE");
5771 vpd_data = kmalloc(256, GFP_KERNEL);
5773 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
5776 nic->mac_control.stats_info->sw_stat.mem_allocated += 256;
5778 for (i = 0; i < 256; i +=4 ) {
5779 pci_write_config_byte(nic->pdev, (vpd_addr + 2), i);
5780 pci_read_config_byte(nic->pdev, (vpd_addr + 2), &data);
5781 pci_write_config_byte(nic->pdev, (vpd_addr + 3), 0);
5782 for (cnt = 0; cnt <5; cnt++) {
5784 pci_read_config_byte(nic->pdev, (vpd_addr + 3), &data);
5789 DBG_PRINT(ERR_DBG, "Read of VPD data failed\n");
5793 pci_read_config_dword(nic->pdev, (vpd_addr + 4),
5794 (u32 *)&vpd_data[i]);
5798 /* read serial number of adapter */
5799 for (cnt = 0; cnt < 256; cnt++) {
5800 if ((vpd_data[cnt] == 'S') &&
5801 (vpd_data[cnt+1] == 'N') &&
5802 (vpd_data[cnt+2] < VPD_STRING_LEN)) {
5803 memset(nic->serial_num, 0, VPD_STRING_LEN);
5804 memcpy(nic->serial_num, &vpd_data[cnt + 3],
5811 if ((!fail) && (vpd_data[1] < VPD_STRING_LEN)) {
5812 memset(nic->product_name, 0, vpd_data[1]);
5813 memcpy(nic->product_name, &vpd_data[3], vpd_data[1]);
5816 nic->mac_control.stats_info->sw_stat.mem_freed += 256;
5820 * s2io_ethtool_geeprom - reads the value stored in the Eeprom.
5821 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5822 * @eeprom : pointer to the user level structure provided by ethtool,
5823 * containing all relevant information.
5824 * @data_buf : user defined value to be written into Eeprom.
5825 * Description: Reads the values stored in the Eeprom at given offset
5826 * for a given length. Stores these values int the input argument data
5827 * buffer 'data_buf' and returns these to the caller (ethtool.)
5832 static int s2io_ethtool_geeprom(struct net_device *dev,
5833 struct ethtool_eeprom *eeprom, u8 * data_buf)
5837 struct s2io_nic *sp = dev->priv;
5839 eeprom->magic = sp->pdev->vendor | (sp->pdev->device << 16);
5841 if ((eeprom->offset + eeprom->len) > (XENA_EEPROM_SPACE))
5842 eeprom->len = XENA_EEPROM_SPACE - eeprom->offset;
5844 for (i = 0; i < eeprom->len; i += 4) {
5845 if (read_eeprom(sp, (eeprom->offset + i), &data)) {
5846 DBG_PRINT(ERR_DBG, "Read of EEPROM failed\n");
5850 memcpy((data_buf + i), &valid, 4);
5856 * s2io_ethtool_seeprom - tries to write the user provided value in Eeprom
5857 * @sp : private member of the device structure, which is a pointer to the
5858 * s2io_nic structure.
5859 * @eeprom : pointer to the user level structure provided by ethtool,
5860 * containing all relevant information.
5861 * @data_buf ; user defined value to be written into Eeprom.
5863 * Tries to write the user provided value in the Eeprom, at the offset
5864 * given by the user.
5866 * 0 on success, -EFAULT on failure.
5869 static int s2io_ethtool_seeprom(struct net_device *dev,
5870 struct ethtool_eeprom *eeprom,
5873 int len = eeprom->len, cnt = 0;
5874 u64 valid = 0, data;
5875 struct s2io_nic *sp = dev->priv;
5877 if (eeprom->magic != (sp->pdev->vendor | (sp->pdev->device << 16))) {
5879 "ETHTOOL_WRITE_EEPROM Err: Magic value ");
5880 DBG_PRINT(ERR_DBG, "is wrong, Its not 0x%x\n",
5886 data = (u32) data_buf[cnt] & 0x000000FF;
5888 valid = (u32) (data << 24);
5892 if (write_eeprom(sp, (eeprom->offset + cnt), valid, 0)) {
5894 "ETHTOOL_WRITE_EEPROM Err: Cannot ");
5896 "write into the specified offset\n");
5907 * s2io_register_test - reads and writes into all clock domains.
5908 * @sp : private member of the device structure, which is a pointer to the
5909 * s2io_nic structure.
5910 * @data : variable that returns the result of each of the test conducted b
5913 * Read and write into all clock domains. The NIC has 3 clock domains,
5914 * see that registers in all the three regions are accessible.
5919 static int s2io_register_test(struct s2io_nic * sp, uint64_t * data)
5921 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5922 u64 val64 = 0, exp_val;
5925 val64 = readq(&bar0->pif_rd_swapper_fb);
5926 if (val64 != 0x123456789abcdefULL) {
5928 DBG_PRINT(INFO_DBG, "Read Test level 1 fails\n");
5931 val64 = readq(&bar0->rmac_pause_cfg);
5932 if (val64 != 0xc000ffff00000000ULL) {
5934 DBG_PRINT(INFO_DBG, "Read Test level 2 fails\n");
5937 val64 = readq(&bar0->rx_queue_cfg);
5938 if (sp->device_type == XFRAME_II_DEVICE)
5939 exp_val = 0x0404040404040404ULL;
5941 exp_val = 0x0808080808080808ULL;
5942 if (val64 != exp_val) {
5944 DBG_PRINT(INFO_DBG, "Read Test level 3 fails\n");
5947 val64 = readq(&bar0->xgxs_efifo_cfg);
5948 if (val64 != 0x000000001923141EULL) {
5950 DBG_PRINT(INFO_DBG, "Read Test level 4 fails\n");
5953 val64 = 0x5A5A5A5A5A5A5A5AULL;
5954 writeq(val64, &bar0->xmsi_data);
5955 val64 = readq(&bar0->xmsi_data);
5956 if (val64 != 0x5A5A5A5A5A5A5A5AULL) {
5958 DBG_PRINT(ERR_DBG, "Write Test level 1 fails\n");
5961 val64 = 0xA5A5A5A5A5A5A5A5ULL;
5962 writeq(val64, &bar0->xmsi_data);
5963 val64 = readq(&bar0->xmsi_data);
5964 if (val64 != 0xA5A5A5A5A5A5A5A5ULL) {
5966 DBG_PRINT(ERR_DBG, "Write Test level 2 fails\n");
5974 * s2io_eeprom_test - to verify that EEprom in the xena can be programmed.
5975 * @sp : private member of the device structure, which is a pointer to the
5976 * s2io_nic structure.
5977 * @data:variable that returns the result of each of the test conducted by
5980 * Verify that EEPROM in the xena can be programmed using I2C_CONTROL
5986 static int s2io_eeprom_test(struct s2io_nic * sp, uint64_t * data)
5989 u64 ret_data, org_4F0, org_7F0;
5990 u8 saved_4F0 = 0, saved_7F0 = 0;
5991 struct net_device *dev = sp->dev;
5993 /* Test Write Error at offset 0 */
5994 /* Note that SPI interface allows write access to all areas
5995 * of EEPROM. Hence doing all negative testing only for Xframe I.
5997 if (sp->device_type == XFRAME_I_DEVICE)
5998 if (!write_eeprom(sp, 0, 0, 3))
6001 /* Save current values at offsets 0x4F0 and 0x7F0 */
6002 if (!read_eeprom(sp, 0x4F0, &org_4F0))
6004 if (!read_eeprom(sp, 0x7F0, &org_7F0))
6007 /* Test Write at offset 4f0 */
6008 if (write_eeprom(sp, 0x4F0, 0x012345, 3))
6010 if (read_eeprom(sp, 0x4F0, &ret_data))
6013 if (ret_data != 0x012345) {
6014 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x4F0. "
6015 "Data written %llx Data read %llx\n",
6016 dev->name, (unsigned long long)0x12345,
6017 (unsigned long long)ret_data);
6021 /* Reset the EEPROM data go FFFF */
6022 write_eeprom(sp, 0x4F0, 0xFFFFFF, 3);
6024 /* Test Write Request Error at offset 0x7c */
6025 if (sp->device_type == XFRAME_I_DEVICE)
6026 if (!write_eeprom(sp, 0x07C, 0, 3))
6029 /* Test Write Request at offset 0x7f0 */
6030 if (write_eeprom(sp, 0x7F0, 0x012345, 3))
6032 if (read_eeprom(sp, 0x7F0, &ret_data))
6035 if (ret_data != 0x012345) {
6036 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x7F0. "
6037 "Data written %llx Data read %llx\n",
6038 dev->name, (unsigned long long)0x12345,
6039 (unsigned long long)ret_data);
6043 /* Reset the EEPROM data go FFFF */
6044 write_eeprom(sp, 0x7F0, 0xFFFFFF, 3);
6046 if (sp->device_type == XFRAME_I_DEVICE) {
6047 /* Test Write Error at offset 0x80 */
6048 if (!write_eeprom(sp, 0x080, 0, 3))
6051 /* Test Write Error at offset 0xfc */
6052 if (!write_eeprom(sp, 0x0FC, 0, 3))
6055 /* Test Write Error at offset 0x100 */
6056 if (!write_eeprom(sp, 0x100, 0, 3))
6059 /* Test Write Error at offset 4ec */
6060 if (!write_eeprom(sp, 0x4EC, 0, 3))
6064 /* Restore values at offsets 0x4F0 and 0x7F0 */
6066 write_eeprom(sp, 0x4F0, org_4F0, 3);
6068 write_eeprom(sp, 0x7F0, org_7F0, 3);
6075 * s2io_bist_test - invokes the MemBist test of the card .
6076 * @sp : private member of the device structure, which is a pointer to the
6077 * s2io_nic structure.
6078 * @data:variable that returns the result of each of the test conducted by
6081 * This invokes the MemBist test of the card. We give around
6082 * 2 secs time for the Test to complete. If it's still not complete
6083 * within this peiod, we consider that the test failed.
6085 * 0 on success and -1 on failure.
6088 static int s2io_bist_test(struct s2io_nic * sp, uint64_t * data)
6091 int cnt = 0, ret = -1;
6093 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
6094 bist |= PCI_BIST_START;
6095 pci_write_config_word(sp->pdev, PCI_BIST, bist);
6098 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
6099 if (!(bist & PCI_BIST_START)) {
6100 *data = (bist & PCI_BIST_CODE_MASK);
6112 * s2io-link_test - verifies the link state of the nic
6113 * @sp ; private member of the device structure, which is a pointer to the
6114 * s2io_nic structure.
6115 * @data: variable that returns the result of each of the test conducted by
6118 * The function verifies the link state of the NIC and updates the input
6119 * argument 'data' appropriately.
6124 static int s2io_link_test(struct s2io_nic * sp, uint64_t * data)
6126 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6129 val64 = readq(&bar0->adapter_status);
6130 if(!(LINK_IS_UP(val64)))
6139 * s2io_rldram_test - offline test for access to the RldRam chip on the NIC
6140 * @sp - private member of the device structure, which is a pointer to the
6141 * s2io_nic structure.
6142 * @data - variable that returns the result of each of the test
6143 * conducted by the driver.
6145 * This is one of the offline test that tests the read and write
6146 * access to the RldRam chip on the NIC.
6151 static int s2io_rldram_test(struct s2io_nic * sp, uint64_t * data)
6153 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6155 int cnt, iteration = 0, test_fail = 0;
6157 val64 = readq(&bar0->adapter_control);
6158 val64 &= ~ADAPTER_ECC_EN;
6159 writeq(val64, &bar0->adapter_control);
6161 val64 = readq(&bar0->mc_rldram_test_ctrl);
6162 val64 |= MC_RLDRAM_TEST_MODE;
6163 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6165 val64 = readq(&bar0->mc_rldram_mrs);
6166 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE;
6167 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
6169 val64 |= MC_RLDRAM_MRS_ENABLE;
6170 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
6172 while (iteration < 2) {
6173 val64 = 0x55555555aaaa0000ULL;
6174 if (iteration == 1) {
6175 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6177 writeq(val64, &bar0->mc_rldram_test_d0);
6179 val64 = 0xaaaa5a5555550000ULL;
6180 if (iteration == 1) {
6181 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6183 writeq(val64, &bar0->mc_rldram_test_d1);
6185 val64 = 0x55aaaaaaaa5a0000ULL;
6186 if (iteration == 1) {
6187 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6189 writeq(val64, &bar0->mc_rldram_test_d2);
6191 val64 = (u64) (0x0000003ffffe0100ULL);
6192 writeq(val64, &bar0->mc_rldram_test_add);
6194 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_WRITE |
6196 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6198 for (cnt = 0; cnt < 5; cnt++) {
6199 val64 = readq(&bar0->mc_rldram_test_ctrl);
6200 if (val64 & MC_RLDRAM_TEST_DONE)
6208 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_GO;
6209 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6211 for (cnt = 0; cnt < 5; cnt++) {
6212 val64 = readq(&bar0->mc_rldram_test_ctrl);
6213 if (val64 & MC_RLDRAM_TEST_DONE)
6221 val64 = readq(&bar0->mc_rldram_test_ctrl);
6222 if (!(val64 & MC_RLDRAM_TEST_PASS))
6230 /* Bring the adapter out of test mode */
6231 SPECIAL_REG_WRITE(0, &bar0->mc_rldram_test_ctrl, LF);
6237 * s2io_ethtool_test - conducts 6 tsets to determine the health of card.
6238 * @sp : private member of the device structure, which is a pointer to the
6239 * s2io_nic structure.
6240 * @ethtest : pointer to a ethtool command specific structure that will be
6241 * returned to the user.
6242 * @data : variable that returns the result of each of the test
6243 * conducted by the driver.
6245 * This function conducts 6 tests ( 4 offline and 2 online) to determine
6246 * the health of the card.
6251 static void s2io_ethtool_test(struct net_device *dev,
6252 struct ethtool_test *ethtest,
6255 struct s2io_nic *sp = dev->priv;
6256 int orig_state = netif_running(sp->dev);
6258 if (ethtest->flags == ETH_TEST_FL_OFFLINE) {
6259 /* Offline Tests. */
6261 s2io_close(sp->dev);
6263 if (s2io_register_test(sp, &data[0]))
6264 ethtest->flags |= ETH_TEST_FL_FAILED;
6268 if (s2io_rldram_test(sp, &data[3]))
6269 ethtest->flags |= ETH_TEST_FL_FAILED;
6273 if (s2io_eeprom_test(sp, &data[1]))
6274 ethtest->flags |= ETH_TEST_FL_FAILED;
6276 if (s2io_bist_test(sp, &data[4]))
6277 ethtest->flags |= ETH_TEST_FL_FAILED;
6287 "%s: is not up, cannot run test\n",
6296 if (s2io_link_test(sp, &data[2]))
6297 ethtest->flags |= ETH_TEST_FL_FAILED;
6306 static void s2io_get_ethtool_stats(struct net_device *dev,
6307 struct ethtool_stats *estats,
6311 struct s2io_nic *sp = dev->priv;
6312 struct stat_block *stat_info = sp->mac_control.stats_info;
6314 s2io_updt_stats(sp);
6316 (u64)le32_to_cpu(stat_info->tmac_frms_oflow) << 32 |
6317 le32_to_cpu(stat_info->tmac_frms);
6319 (u64)le32_to_cpu(stat_info->tmac_data_octets_oflow) << 32 |
6320 le32_to_cpu(stat_info->tmac_data_octets);
6321 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms);
6323 (u64)le32_to_cpu(stat_info->tmac_mcst_frms_oflow) << 32 |
6324 le32_to_cpu(stat_info->tmac_mcst_frms);
6326 (u64)le32_to_cpu(stat_info->tmac_bcst_frms_oflow) << 32 |
6327 le32_to_cpu(stat_info->tmac_bcst_frms);
6328 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_pause_ctrl_frms);
6330 (u64)le32_to_cpu(stat_info->tmac_ttl_octets_oflow) << 32 |
6331 le32_to_cpu(stat_info->tmac_ttl_octets);
6333 (u64)le32_to_cpu(stat_info->tmac_ucst_frms_oflow) << 32 |
6334 le32_to_cpu(stat_info->tmac_ucst_frms);
6336 (u64)le32_to_cpu(stat_info->tmac_nucst_frms_oflow) << 32 |
6337 le32_to_cpu(stat_info->tmac_nucst_frms);
6339 (u64)le32_to_cpu(stat_info->tmac_any_err_frms_oflow) << 32 |
6340 le32_to_cpu(stat_info->tmac_any_err_frms);
6341 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_ttl_less_fb_octets);
6342 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_vld_ip_octets);
6344 (u64)le32_to_cpu(stat_info->tmac_vld_ip_oflow) << 32 |
6345 le32_to_cpu(stat_info->tmac_vld_ip);
6347 (u64)le32_to_cpu(stat_info->tmac_drop_ip_oflow) << 32 |
6348 le32_to_cpu(stat_info->tmac_drop_ip);
6350 (u64)le32_to_cpu(stat_info->tmac_icmp_oflow) << 32 |
6351 le32_to_cpu(stat_info->tmac_icmp);
6353 (u64)le32_to_cpu(stat_info->tmac_rst_tcp_oflow) << 32 |
6354 le32_to_cpu(stat_info->tmac_rst_tcp);
6355 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_tcp);
6356 tmp_stats[i++] = (u64)le32_to_cpu(stat_info->tmac_udp_oflow) << 32 |
6357 le32_to_cpu(stat_info->tmac_udp);
6359 (u64)le32_to_cpu(stat_info->rmac_vld_frms_oflow) << 32 |
6360 le32_to_cpu(stat_info->rmac_vld_frms);
6362 (u64)le32_to_cpu(stat_info->rmac_data_octets_oflow) << 32 |
6363 le32_to_cpu(stat_info->rmac_data_octets);
6364 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_fcs_err_frms);
6365 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_drop_frms);
6367 (u64)le32_to_cpu(stat_info->rmac_vld_mcst_frms_oflow) << 32 |
6368 le32_to_cpu(stat_info->rmac_vld_mcst_frms);
6370 (u64)le32_to_cpu(stat_info->rmac_vld_bcst_frms_oflow) << 32 |
6371 le32_to_cpu(stat_info->rmac_vld_bcst_frms);
6372 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_in_rng_len_err_frms);
6373 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_out_rng_len_err_frms);
6374 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_long_frms);
6375 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_pause_ctrl_frms);
6376 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_unsup_ctrl_frms);
6378 (u64)le32_to_cpu(stat_info->rmac_ttl_octets_oflow) << 32 |
6379 le32_to_cpu(stat_info->rmac_ttl_octets);
6381 (u64)le32_to_cpu(stat_info->rmac_accepted_ucst_frms_oflow)
6382 << 32 | le32_to_cpu(stat_info->rmac_accepted_ucst_frms);
6384 (u64)le32_to_cpu(stat_info->rmac_accepted_nucst_frms_oflow)
6385 << 32 | le32_to_cpu(stat_info->rmac_accepted_nucst_frms);
6387 (u64)le32_to_cpu(stat_info->rmac_discarded_frms_oflow) << 32 |
6388 le32_to_cpu(stat_info->rmac_discarded_frms);
6390 (u64)le32_to_cpu(stat_info->rmac_drop_events_oflow)
6391 << 32 | le32_to_cpu(stat_info->rmac_drop_events);
6392 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_less_fb_octets);
6393 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_frms);
6395 (u64)le32_to_cpu(stat_info->rmac_usized_frms_oflow) << 32 |
6396 le32_to_cpu(stat_info->rmac_usized_frms);
6398 (u64)le32_to_cpu(stat_info->rmac_osized_frms_oflow) << 32 |
6399 le32_to_cpu(stat_info->rmac_osized_frms);
6401 (u64)le32_to_cpu(stat_info->rmac_frag_frms_oflow) << 32 |
6402 le32_to_cpu(stat_info->rmac_frag_frms);
6404 (u64)le32_to_cpu(stat_info->rmac_jabber_frms_oflow) << 32 |
6405 le32_to_cpu(stat_info->rmac_jabber_frms);
6406 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_64_frms);
6407 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_65_127_frms);
6408 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_128_255_frms);
6409 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_256_511_frms);
6410 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_512_1023_frms);
6411 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_1024_1518_frms);
6413 (u64)le32_to_cpu(stat_info->rmac_ip_oflow) << 32 |
6414 le32_to_cpu(stat_info->rmac_ip);
6415 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ip_octets);
6416 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_hdr_err_ip);
6418 (u64)le32_to_cpu(stat_info->rmac_drop_ip_oflow) << 32 |
6419 le32_to_cpu(stat_info->rmac_drop_ip);
6421 (u64)le32_to_cpu(stat_info->rmac_icmp_oflow) << 32 |
6422 le32_to_cpu(stat_info->rmac_icmp);
6423 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_tcp);
6425 (u64)le32_to_cpu(stat_info->rmac_udp_oflow) << 32 |
6426 le32_to_cpu(stat_info->rmac_udp);
6428 (u64)le32_to_cpu(stat_info->rmac_err_drp_udp_oflow) << 32 |
6429 le32_to_cpu(stat_info->rmac_err_drp_udp);
6430 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_err_sym);
6431 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q0);
6432 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q1);
6433 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q2);
6434 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q3);
6435 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q4);
6436 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q5);
6437 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q6);
6438 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q7);
6439 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q0);
6440 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q1);
6441 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q2);
6442 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q3);
6443 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q4);
6444 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q5);
6445 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q6);
6446 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q7);
6448 (u64)le32_to_cpu(stat_info->rmac_pause_cnt_oflow) << 32 |
6449 le32_to_cpu(stat_info->rmac_pause_cnt);
6450 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_data_err_cnt);
6451 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_ctrl_err_cnt);
6453 (u64)le32_to_cpu(stat_info->rmac_accepted_ip_oflow) << 32 |
6454 le32_to_cpu(stat_info->rmac_accepted_ip);
6455 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp);
6456 tmp_stats[i++] = le32_to_cpu(stat_info->rd_req_cnt);
6457 tmp_stats[i++] = le32_to_cpu(stat_info->new_rd_req_cnt);
6458 tmp_stats[i++] = le32_to_cpu(stat_info->new_rd_req_rtry_cnt);
6459 tmp_stats[i++] = le32_to_cpu(stat_info->rd_rtry_cnt);
6460 tmp_stats[i++] = le32_to_cpu(stat_info->wr_rtry_rd_ack_cnt);
6461 tmp_stats[i++] = le32_to_cpu(stat_info->wr_req_cnt);
6462 tmp_stats[i++] = le32_to_cpu(stat_info->new_wr_req_cnt);
6463 tmp_stats[i++] = le32_to_cpu(stat_info->new_wr_req_rtry_cnt);
6464 tmp_stats[i++] = le32_to_cpu(stat_info->wr_rtry_cnt);
6465 tmp_stats[i++] = le32_to_cpu(stat_info->wr_disc_cnt);
6466 tmp_stats[i++] = le32_to_cpu(stat_info->rd_rtry_wr_ack_cnt);
6467 tmp_stats[i++] = le32_to_cpu(stat_info->txp_wr_cnt);
6468 tmp_stats[i++] = le32_to_cpu(stat_info->txd_rd_cnt);
6469 tmp_stats[i++] = le32_to_cpu(stat_info->txd_wr_cnt);
6470 tmp_stats[i++] = le32_to_cpu(stat_info->rxd_rd_cnt);
6471 tmp_stats[i++] = le32_to_cpu(stat_info->rxd_wr_cnt);
6472 tmp_stats[i++] = le32_to_cpu(stat_info->txf_rd_cnt);
6473 tmp_stats[i++] = le32_to_cpu(stat_info->rxf_wr_cnt);
6475 /* Enhanced statistics exist only for Hercules */
6476 if(sp->device_type == XFRAME_II_DEVICE) {
6478 le64_to_cpu(stat_info->rmac_ttl_1519_4095_frms);
6480 le64_to_cpu(stat_info->rmac_ttl_4096_8191_frms);
6482 le64_to_cpu(stat_info->rmac_ttl_8192_max_frms);
6483 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_gt_max_frms);
6484 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_osized_alt_frms);
6485 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_jabber_alt_frms);
6486 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_gt_max_alt_frms);
6487 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_vlan_frms);
6488 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_len_discard);
6489 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_fcs_discard);
6490 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pf_discard);
6491 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_da_discard);
6492 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_red_discard);
6493 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_rts_discard);
6494 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_ingm_full_discard);
6495 tmp_stats[i++] = le32_to_cpu(stat_info->link_fault_cnt);
6499 tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs;
6500 tmp_stats[i++] = stat_info->sw_stat.double_ecc_errs;
6501 tmp_stats[i++] = stat_info->sw_stat.parity_err_cnt;
6502 tmp_stats[i++] = stat_info->sw_stat.serious_err_cnt;
6503 tmp_stats[i++] = stat_info->sw_stat.soft_reset_cnt;
6504 tmp_stats[i++] = stat_info->sw_stat.fifo_full_cnt;
6505 for (k = 0; k < MAX_RX_RINGS; k++)
6506 tmp_stats[i++] = stat_info->sw_stat.ring_full_cnt[k];
6507 tmp_stats[i++] = stat_info->xpak_stat.alarm_transceiver_temp_high;
6508 tmp_stats[i++] = stat_info->xpak_stat.alarm_transceiver_temp_low;
6509 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_bias_current_high;
6510 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_bias_current_low;
6511 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_output_power_high;
6512 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_output_power_low;
6513 tmp_stats[i++] = stat_info->xpak_stat.warn_transceiver_temp_high;
6514 tmp_stats[i++] = stat_info->xpak_stat.warn_transceiver_temp_low;
6515 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_bias_current_high;
6516 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_bias_current_low;
6517 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_output_power_high;
6518 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_output_power_low;
6519 tmp_stats[i++] = stat_info->sw_stat.clubbed_frms_cnt;
6520 tmp_stats[i++] = stat_info->sw_stat.sending_both;
6521 tmp_stats[i++] = stat_info->sw_stat.outof_sequence_pkts;
6522 tmp_stats[i++] = stat_info->sw_stat.flush_max_pkts;
6523 if (stat_info->sw_stat.num_aggregations) {
6524 u64 tmp = stat_info->sw_stat.sum_avg_pkts_aggregated;
6527 * Since 64-bit divide does not work on all platforms,
6528 * do repeated subtraction.
6530 while (tmp >= stat_info->sw_stat.num_aggregations) {
6531 tmp -= stat_info->sw_stat.num_aggregations;
6534 tmp_stats[i++] = count;
6538 tmp_stats[i++] = stat_info->sw_stat.mem_alloc_fail_cnt;
6539 tmp_stats[i++] = stat_info->sw_stat.pci_map_fail_cnt;
6540 tmp_stats[i++] = stat_info->sw_stat.watchdog_timer_cnt;
6541 tmp_stats[i++] = stat_info->sw_stat.mem_allocated;
6542 tmp_stats[i++] = stat_info->sw_stat.mem_freed;
6543 tmp_stats[i++] = stat_info->sw_stat.link_up_cnt;
6544 tmp_stats[i++] = stat_info->sw_stat.link_down_cnt;
6545 tmp_stats[i++] = stat_info->sw_stat.link_up_time;
6546 tmp_stats[i++] = stat_info->sw_stat.link_down_time;
6548 tmp_stats[i++] = stat_info->sw_stat.tx_buf_abort_cnt;
6549 tmp_stats[i++] = stat_info->sw_stat.tx_desc_abort_cnt;
6550 tmp_stats[i++] = stat_info->sw_stat.tx_parity_err_cnt;
6551 tmp_stats[i++] = stat_info->sw_stat.tx_link_loss_cnt;
6552 tmp_stats[i++] = stat_info->sw_stat.tx_list_proc_err_cnt;
6554 tmp_stats[i++] = stat_info->sw_stat.rx_parity_err_cnt;
6555 tmp_stats[i++] = stat_info->sw_stat.rx_abort_cnt;
6556 tmp_stats[i++] = stat_info->sw_stat.rx_parity_abort_cnt;
6557 tmp_stats[i++] = stat_info->sw_stat.rx_rda_fail_cnt;
6558 tmp_stats[i++] = stat_info->sw_stat.rx_unkn_prot_cnt;
6559 tmp_stats[i++] = stat_info->sw_stat.rx_fcs_err_cnt;
6560 tmp_stats[i++] = stat_info->sw_stat.rx_buf_size_err_cnt;
6561 tmp_stats[i++] = stat_info->sw_stat.rx_rxd_corrupt_cnt;
6562 tmp_stats[i++] = stat_info->sw_stat.rx_unkn_err_cnt;
6563 tmp_stats[i++] = stat_info->sw_stat.tda_err_cnt;
6564 tmp_stats[i++] = stat_info->sw_stat.pfc_err_cnt;
6565 tmp_stats[i++] = stat_info->sw_stat.pcc_err_cnt;
6566 tmp_stats[i++] = stat_info->sw_stat.tti_err_cnt;
6567 tmp_stats[i++] = stat_info->sw_stat.tpa_err_cnt;
6568 tmp_stats[i++] = stat_info->sw_stat.sm_err_cnt;
6569 tmp_stats[i++] = stat_info->sw_stat.lso_err_cnt;
6570 tmp_stats[i++] = stat_info->sw_stat.mac_tmac_err_cnt;
6571 tmp_stats[i++] = stat_info->sw_stat.mac_rmac_err_cnt;
6572 tmp_stats[i++] = stat_info->sw_stat.xgxs_txgxs_err_cnt;
6573 tmp_stats[i++] = stat_info->sw_stat.xgxs_rxgxs_err_cnt;
6574 tmp_stats[i++] = stat_info->sw_stat.rc_err_cnt;
6575 tmp_stats[i++] = stat_info->sw_stat.prc_pcix_err_cnt;
6576 tmp_stats[i++] = stat_info->sw_stat.rpa_err_cnt;
6577 tmp_stats[i++] = stat_info->sw_stat.rda_err_cnt;
6578 tmp_stats[i++] = stat_info->sw_stat.rti_err_cnt;
6579 tmp_stats[i++] = stat_info->sw_stat.mc_err_cnt;
6582 static int s2io_ethtool_get_regs_len(struct net_device *dev)
6584 return (XENA_REG_SPACE);
6588 static u32 s2io_ethtool_get_rx_csum(struct net_device * dev)
6590 struct s2io_nic *sp = dev->priv;
6592 return (sp->rx_csum);
6595 static int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data)
6597 struct s2io_nic *sp = dev->priv;
6607 static int s2io_get_eeprom_len(struct net_device *dev)
6609 return (XENA_EEPROM_SPACE);
6612 static int s2io_get_sset_count(struct net_device *dev, int sset)
6614 struct s2io_nic *sp = dev->priv;
6618 return S2IO_TEST_LEN;
6620 switch(sp->device_type) {
6621 case XFRAME_I_DEVICE:
6622 return XFRAME_I_STAT_LEN;
6623 case XFRAME_II_DEVICE:
6624 return XFRAME_II_STAT_LEN;
6633 static void s2io_ethtool_get_strings(struct net_device *dev,
6634 u32 stringset, u8 * data)
6637 struct s2io_nic *sp = dev->priv;
6639 switch (stringset) {
6641 memcpy(data, s2io_gstrings, S2IO_STRINGS_LEN);
6644 stat_size = sizeof(ethtool_xena_stats_keys);
6645 memcpy(data, ðtool_xena_stats_keys,stat_size);
6646 if(sp->device_type == XFRAME_II_DEVICE) {
6647 memcpy(data + stat_size,
6648 ðtool_enhanced_stats_keys,
6649 sizeof(ethtool_enhanced_stats_keys));
6650 stat_size += sizeof(ethtool_enhanced_stats_keys);
6653 memcpy(data + stat_size, ðtool_driver_stats_keys,
6654 sizeof(ethtool_driver_stats_keys));
6658 static int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data)
6661 dev->features |= NETIF_F_IP_CSUM;
6663 dev->features &= ~NETIF_F_IP_CSUM;
6668 static u32 s2io_ethtool_op_get_tso(struct net_device *dev)
6670 return (dev->features & NETIF_F_TSO) != 0;
6672 static int s2io_ethtool_op_set_tso(struct net_device *dev, u32 data)
6675 dev->features |= (NETIF_F_TSO | NETIF_F_TSO6);
6677 dev->features &= ~(NETIF_F_TSO | NETIF_F_TSO6);
6682 static const struct ethtool_ops netdev_ethtool_ops = {
6683 .get_settings = s2io_ethtool_gset,
6684 .set_settings = s2io_ethtool_sset,
6685 .get_drvinfo = s2io_ethtool_gdrvinfo,
6686 .get_regs_len = s2io_ethtool_get_regs_len,
6687 .get_regs = s2io_ethtool_gregs,
6688 .get_link = ethtool_op_get_link,
6689 .get_eeprom_len = s2io_get_eeprom_len,
6690 .get_eeprom = s2io_ethtool_geeprom,
6691 .set_eeprom = s2io_ethtool_seeprom,
6692 .get_ringparam = s2io_ethtool_gringparam,
6693 .get_pauseparam = s2io_ethtool_getpause_data,
6694 .set_pauseparam = s2io_ethtool_setpause_data,
6695 .get_rx_csum = s2io_ethtool_get_rx_csum,
6696 .set_rx_csum = s2io_ethtool_set_rx_csum,
6697 .set_tx_csum = s2io_ethtool_op_set_tx_csum,
6698 .set_sg = ethtool_op_set_sg,
6699 .get_tso = s2io_ethtool_op_get_tso,
6700 .set_tso = s2io_ethtool_op_set_tso,
6701 .set_ufo = ethtool_op_set_ufo,
6702 .self_test = s2io_ethtool_test,
6703 .get_strings = s2io_ethtool_get_strings,
6704 .phys_id = s2io_ethtool_idnic,
6705 .get_ethtool_stats = s2io_get_ethtool_stats,
6706 .get_sset_count = s2io_get_sset_count,
6710 * s2io_ioctl - Entry point for the Ioctl
6711 * @dev : Device pointer.
6712 * @ifr : An IOCTL specefic structure, that can contain a pointer to
6713 * a proprietary structure used to pass information to the driver.
6714 * @cmd : This is used to distinguish between the different commands that
6715 * can be passed to the IOCTL functions.
6717 * Currently there are no special functionality supported in IOCTL, hence
6718 * function always return EOPNOTSUPPORTED
6721 static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
6727 * s2io_change_mtu - entry point to change MTU size for the device.
6728 * @dev : device pointer.
6729 * @new_mtu : the new MTU size for the device.
6730 * Description: A driver entry point to change MTU size for the device.
6731 * Before changing the MTU the device must be stopped.
6733 * 0 on success and an appropriate (-)ve integer as defined in errno.h
6737 static int s2io_change_mtu(struct net_device *dev, int new_mtu)
6739 struct s2io_nic *sp = dev->priv;
6742 if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) {
6743 DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n",
6749 if (netif_running(dev)) {
6750 s2io_stop_all_tx_queue(sp);
6752 ret = s2io_card_up(sp);
6754 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
6758 s2io_wake_all_tx_queue(sp);
6759 } else { /* Device is down */
6760 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6761 u64 val64 = new_mtu;
6763 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
6770 * s2io_tasklet - Bottom half of the ISR.
6771 * @dev_adr : address of the device structure in dma_addr_t format.
6773 * This is the tasklet or the bottom half of the ISR. This is
6774 * an extension of the ISR which is scheduled by the scheduler to be run
6775 * when the load on the CPU is low. All low priority tasks of the ISR can
6776 * be pushed into the tasklet. For now the tasklet is used only to
6777 * replenish the Rx buffers in the Rx buffer descriptors.
6782 static void s2io_tasklet(unsigned long dev_addr)
6784 struct net_device *dev = (struct net_device *) dev_addr;
6785 struct s2io_nic *sp = dev->priv;
6787 struct mac_info *mac_control;
6788 struct config_param *config;
6790 mac_control = &sp->mac_control;
6791 config = &sp->config;
6793 if (!TASKLET_IN_USE) {
6794 for (i = 0; i < config->rx_ring_num; i++) {
6795 ret = fill_rx_buffers(sp, i);
6796 if (ret == -ENOMEM) {
6797 DBG_PRINT(INFO_DBG, "%s: Out of ",
6799 DBG_PRINT(INFO_DBG, "memory in tasklet\n");
6801 } else if (ret == -EFILL) {
6803 "%s: Rx Ring %d is full\n",
6808 clear_bit(0, (&sp->tasklet_status));
6813 * s2io_set_link - Set the LInk status
6814 * @data: long pointer to device private structue
6815 * Description: Sets the link status for the adapter
6818 static void s2io_set_link(struct work_struct *work)
6820 struct s2io_nic *nic = container_of(work, struct s2io_nic, set_link_task);
6821 struct net_device *dev = nic->dev;
6822 struct XENA_dev_config __iomem *bar0 = nic->bar0;
6828 if (!netif_running(dev))
6831 if (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(nic->state))) {
6832 /* The card is being reset, no point doing anything */
6836 subid = nic->pdev->subsystem_device;
6837 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
6839 * Allow a small delay for the NICs self initiated
6840 * cleanup to complete.
6845 val64 = readq(&bar0->adapter_status);
6846 if (LINK_IS_UP(val64)) {
6847 if (!(readq(&bar0->adapter_control) & ADAPTER_CNTL_EN)) {
6848 if (verify_xena_quiescence(nic)) {
6849 val64 = readq(&bar0->adapter_control);
6850 val64 |= ADAPTER_CNTL_EN;
6851 writeq(val64, &bar0->adapter_control);
6852 if (CARDS_WITH_FAULTY_LINK_INDICATORS(
6853 nic->device_type, subid)) {
6854 val64 = readq(&bar0->gpio_control);
6855 val64 |= GPIO_CTRL_GPIO_0;
6856 writeq(val64, &bar0->gpio_control);
6857 val64 = readq(&bar0->gpio_control);
6859 val64 |= ADAPTER_LED_ON;
6860 writeq(val64, &bar0->adapter_control);
6862 nic->device_enabled_once = TRUE;
6864 DBG_PRINT(ERR_DBG, "%s: Error: ", dev->name);
6865 DBG_PRINT(ERR_DBG, "device is not Quiescent\n");
6866 s2io_stop_all_tx_queue(nic);
6869 val64 = readq(&bar0->adapter_control);
6870 val64 |= ADAPTER_LED_ON;
6871 writeq(val64, &bar0->adapter_control);
6872 s2io_link(nic, LINK_UP);
6874 if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
6876 val64 = readq(&bar0->gpio_control);
6877 val64 &= ~GPIO_CTRL_GPIO_0;
6878 writeq(val64, &bar0->gpio_control);
6879 val64 = readq(&bar0->gpio_control);
6882 val64 = readq(&bar0->adapter_control);
6883 val64 = val64 &(~ADAPTER_LED_ON);
6884 writeq(val64, &bar0->adapter_control);
6885 s2io_link(nic, LINK_DOWN);
6887 clear_bit(__S2IO_STATE_LINK_TASK, &(nic->state));
6893 static int set_rxd_buffer_pointer(struct s2io_nic *sp, struct RxD_t *rxdp,
6895 struct sk_buff **skb, u64 *temp0, u64 *temp1,
6896 u64 *temp2, int size)
6898 struct net_device *dev = sp->dev;
6899 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
6901 if ((sp->rxd_mode == RXD_MODE_1) && (rxdp->Host_Control == 0)) {
6902 struct RxD1 *rxdp1 = (struct RxD1 *)rxdp;
6905 DBG_PRINT(INFO_DBG, "SKB is not NULL\n");
6907 * As Rx frame are not going to be processed,
6908 * using same mapped address for the Rxd
6911 rxdp1->Buffer0_ptr = *temp0;
6913 *skb = dev_alloc_skb(size);
6915 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
6916 DBG_PRINT(INFO_DBG, "memory to allocate ");
6917 DBG_PRINT(INFO_DBG, "1 buf mode SKBs\n");
6918 sp->mac_control.stats_info->sw_stat. \
6919 mem_alloc_fail_cnt++;
6922 sp->mac_control.stats_info->sw_stat.mem_allocated
6923 += (*skb)->truesize;
6924 /* storing the mapped addr in a temp variable
6925 * such it will be used for next rxd whose
6926 * Host Control is NULL
6928 rxdp1->Buffer0_ptr = *temp0 =
6929 pci_map_single( sp->pdev, (*skb)->data,
6930 size - NET_IP_ALIGN,
6931 PCI_DMA_FROMDEVICE);
6932 if( (rxdp1->Buffer0_ptr == 0) ||
6933 (rxdp1->Buffer0_ptr == DMA_ERROR_CODE)) {
6934 goto memalloc_failed;
6936 rxdp->Host_Control = (unsigned long) (*skb);
6938 } else if ((sp->rxd_mode == RXD_MODE_3B) && (rxdp->Host_Control == 0)) {
6939 struct RxD3 *rxdp3 = (struct RxD3 *)rxdp;
6940 /* Two buffer Mode */
6942 rxdp3->Buffer2_ptr = *temp2;
6943 rxdp3->Buffer0_ptr = *temp0;
6944 rxdp3->Buffer1_ptr = *temp1;
6946 *skb = dev_alloc_skb(size);
6948 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
6949 DBG_PRINT(INFO_DBG, "memory to allocate ");
6950 DBG_PRINT(INFO_DBG, "2 buf mode SKBs\n");
6951 sp->mac_control.stats_info->sw_stat. \
6952 mem_alloc_fail_cnt++;
6955 sp->mac_control.stats_info->sw_stat.mem_allocated
6956 += (*skb)->truesize;
6957 rxdp3->Buffer2_ptr = *temp2 =
6958 pci_map_single(sp->pdev, (*skb)->data,
6960 PCI_DMA_FROMDEVICE);
6961 if( (rxdp3->Buffer2_ptr == 0) ||
6962 (rxdp3->Buffer2_ptr == DMA_ERROR_CODE)) {
6963 goto memalloc_failed;
6965 rxdp3->Buffer0_ptr = *temp0 =
6966 pci_map_single( sp->pdev, ba->ba_0, BUF0_LEN,
6967 PCI_DMA_FROMDEVICE);
6968 if( (rxdp3->Buffer0_ptr == 0) ||
6969 (rxdp3->Buffer0_ptr == DMA_ERROR_CODE)) {
6970 pci_unmap_single (sp->pdev,
6971 (dma_addr_t)rxdp3->Buffer2_ptr,
6972 dev->mtu + 4, PCI_DMA_FROMDEVICE);
6973 goto memalloc_failed;
6975 rxdp->Host_Control = (unsigned long) (*skb);
6977 /* Buffer-1 will be dummy buffer not used */
6978 rxdp3->Buffer1_ptr = *temp1 =
6979 pci_map_single(sp->pdev, ba->ba_1, BUF1_LEN,
6980 PCI_DMA_FROMDEVICE);
6981 if( (rxdp3->Buffer1_ptr == 0) ||
6982 (rxdp3->Buffer1_ptr == DMA_ERROR_CODE)) {
6983 pci_unmap_single (sp->pdev,
6984 (dma_addr_t)rxdp3->Buffer0_ptr,
6985 BUF0_LEN, PCI_DMA_FROMDEVICE);
6986 pci_unmap_single (sp->pdev,
6987 (dma_addr_t)rxdp3->Buffer2_ptr,
6988 dev->mtu + 4, PCI_DMA_FROMDEVICE);
6989 goto memalloc_failed;
6995 stats->pci_map_fail_cnt++;
6996 stats->mem_freed += (*skb)->truesize;
6997 dev_kfree_skb(*skb);
7001 static void set_rxd_buffer_size(struct s2io_nic *sp, struct RxD_t *rxdp,
7004 struct net_device *dev = sp->dev;
7005 if (sp->rxd_mode == RXD_MODE_1) {
7006 rxdp->Control_2 = SET_BUFFER0_SIZE_1( size - NET_IP_ALIGN);
7007 } else if (sp->rxd_mode == RXD_MODE_3B) {
7008 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
7009 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
7010 rxdp->Control_2 |= SET_BUFFER2_SIZE_3( dev->mtu + 4);
7014 static int rxd_owner_bit_reset(struct s2io_nic *sp)
7016 int i, j, k, blk_cnt = 0, size;
7017 struct mac_info * mac_control = &sp->mac_control;
7018 struct config_param *config = &sp->config;
7019 struct net_device *dev = sp->dev;
7020 struct RxD_t *rxdp = NULL;
7021 struct sk_buff *skb = NULL;
7022 struct buffAdd *ba = NULL;
7023 u64 temp0_64 = 0, temp1_64 = 0, temp2_64 = 0;
7025 /* Calculate the size based on ring mode */
7026 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
7027 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
7028 if (sp->rxd_mode == RXD_MODE_1)
7029 size += NET_IP_ALIGN;
7030 else if (sp->rxd_mode == RXD_MODE_3B)
7031 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
7033 for (i = 0; i < config->rx_ring_num; i++) {
7034 blk_cnt = config->rx_cfg[i].num_rxd /
7035 (rxd_count[sp->rxd_mode] +1);
7037 for (j = 0; j < blk_cnt; j++) {
7038 for (k = 0; k < rxd_count[sp->rxd_mode]; k++) {
7039 rxdp = mac_control->rings[i].
7040 rx_blocks[j].rxds[k].virt_addr;
7041 if(sp->rxd_mode == RXD_MODE_3B)
7042 ba = &mac_control->rings[i].ba[j][k];
7043 if (set_rxd_buffer_pointer(sp, rxdp, ba,
7044 &skb,(u64 *)&temp0_64,
7051 set_rxd_buffer_size(sp, rxdp, size);
7053 /* flip the Ownership bit to Hardware */
7054 rxdp->Control_1 |= RXD_OWN_XENA;
7062 static int s2io_add_isr(struct s2io_nic * sp)
7065 struct net_device *dev = sp->dev;
7068 if (sp->config.intr_type == MSI_X)
7069 ret = s2io_enable_msi_x(sp);
7071 DBG_PRINT(ERR_DBG, "%s: Defaulting to INTA\n", dev->name);
7072 sp->config.intr_type = INTA;
7075 /* Store the values of the MSIX table in the struct s2io_nic structure */
7076 store_xmsi_data(sp);
7078 /* After proper initialization of H/W, register ISR */
7079 if (sp->config.intr_type == MSI_X) {
7080 int i, msix_tx_cnt=0,msix_rx_cnt=0;
7082 for (i=1; (sp->s2io_entries[i].in_use == MSIX_FLG); i++) {
7083 if (sp->s2io_entries[i].type == MSIX_FIFO_TYPE) {
7084 sprintf(sp->desc[i], "%s:MSI-X-%d-TX",
7086 err = request_irq(sp->entries[i].vector,
7087 s2io_msix_fifo_handle, 0, sp->desc[i],
7088 sp->s2io_entries[i].arg);
7089 /* If either data or addr is zero print it */
7090 if(!(sp->msix_info[i].addr &&
7091 sp->msix_info[i].data)) {
7092 DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx "
7093 "Data:0x%llx\n",sp->desc[i],
7094 (unsigned long long)
7095 sp->msix_info[i].addr,
7096 (unsigned long long)
7097 sp->msix_info[i].data);
7102 sprintf(sp->desc[i], "%s:MSI-X-%d-RX",
7104 err = request_irq(sp->entries[i].vector,
7105 s2io_msix_ring_handle, 0, sp->desc[i],
7106 sp->s2io_entries[i].arg);
7107 /* If either data or addr is zero print it */
7108 if(!(sp->msix_info[i].addr &&
7109 sp->msix_info[i].data)) {
7110 DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx "
7111 "Data:0x%llx\n",sp->desc[i],
7112 (unsigned long long)
7113 sp->msix_info[i].addr,
7114 (unsigned long long)
7115 sp->msix_info[i].data);
7121 remove_msix_isr(sp);
7122 DBG_PRINT(ERR_DBG,"%s:MSI-X-%d registration "
7123 "failed\n", dev->name, i);
7124 DBG_PRINT(ERR_DBG, "%s: defaulting to INTA\n",
7126 sp->config.intr_type = INTA;
7129 sp->s2io_entries[i].in_use = MSIX_REGISTERED_SUCCESS;
7132 printk(KERN_INFO "MSI-X-TX %d entries enabled\n",
7134 printk(KERN_INFO "MSI-X-RX %d entries enabled\n",
7138 if (sp->config.intr_type == INTA) {
7139 err = request_irq((int) sp->pdev->irq, s2io_isr, IRQF_SHARED,
7142 DBG_PRINT(ERR_DBG, "%s: ISR registration failed\n",
7149 static void s2io_rem_isr(struct s2io_nic * sp)
7151 if (sp->config.intr_type == MSI_X)
7152 remove_msix_isr(sp);
7154 remove_inta_isr(sp);
7157 static void do_s2io_card_down(struct s2io_nic * sp, int do_io)
7160 struct XENA_dev_config __iomem *bar0 = sp->bar0;
7161 unsigned long flags;
7162 register u64 val64 = 0;
7163 struct config_param *config;
7164 config = &sp->config;
7166 if (!is_s2io_card_up(sp))
7169 del_timer_sync(&sp->alarm_timer);
7170 /* If s2io_set_link task is executing, wait till it completes. */
7171 while (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(sp->state))) {
7174 clear_bit(__S2IO_STATE_CARD_UP, &sp->state);
7178 napi_disable(&sp->napi);
7180 /* disable Tx and Rx traffic on the NIC */
7187 tasklet_kill(&sp->task);
7189 /* Check if the device is Quiescent and then Reset the NIC */
7191 /* As per the HW requirement we need to replenish the
7192 * receive buffer to avoid the ring bump. Since there is
7193 * no intention of processing the Rx frame at this pointwe are
7194 * just settting the ownership bit of rxd in Each Rx
7195 * ring to HW and set the appropriate buffer size
7196 * based on the ring mode
7198 rxd_owner_bit_reset(sp);
7200 val64 = readq(&bar0->adapter_status);
7201 if (verify_xena_quiescence(sp)) {
7202 if(verify_pcc_quiescent(sp, sp->device_enabled_once))
7210 "s2io_close:Device not Quiescent ");
7211 DBG_PRINT(ERR_DBG, "adaper status reads 0x%llx\n",
7212 (unsigned long long) val64);
7219 /* Free all Tx buffers */
7220 free_tx_buffers(sp);
7222 /* Free all Rx buffers */
7223 spin_lock_irqsave(&sp->rx_lock, flags);
7224 free_rx_buffers(sp);
7225 spin_unlock_irqrestore(&sp->rx_lock, flags);
7227 clear_bit(__S2IO_STATE_LINK_TASK, &(sp->state));
7230 static void s2io_card_down(struct s2io_nic * sp)
7232 do_s2io_card_down(sp, 1);
7235 static int s2io_card_up(struct s2io_nic * sp)
7238 struct mac_info *mac_control;
7239 struct config_param *config;
7240 struct net_device *dev = (struct net_device *) sp->dev;
7243 /* Initialize the H/W I/O registers */
7246 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
7254 * Initializing the Rx buffers. For now we are considering only 1
7255 * Rx ring and initializing buffers into 30 Rx blocks
7257 mac_control = &sp->mac_control;
7258 config = &sp->config;
7260 for (i = 0; i < config->rx_ring_num; i++) {
7261 if ((ret = fill_rx_buffers(sp, i))) {
7262 DBG_PRINT(ERR_DBG, "%s: Out of memory in Open\n",
7265 free_rx_buffers(sp);
7268 DBG_PRINT(INFO_DBG, "Buf in ring:%d is %d:\n", i,
7269 atomic_read(&sp->rx_bufs_left[i]));
7272 /* Initialise napi */
7274 napi_enable(&sp->napi);
7276 /* Maintain the state prior to the open */
7277 if (sp->promisc_flg)
7278 sp->promisc_flg = 0;
7279 if (sp->m_cast_flg) {
7281 sp->all_multi_pos= 0;
7284 /* Setting its receive mode */
7285 s2io_set_multicast(dev);
7288 /* Initialize max aggregatable pkts per session based on MTU */
7289 sp->lro_max_aggr_per_sess = ((1<<16) - 1) / dev->mtu;
7290 /* Check if we can use(if specified) user provided value */
7291 if (lro_max_pkts < sp->lro_max_aggr_per_sess)
7292 sp->lro_max_aggr_per_sess = lro_max_pkts;
7295 /* Enable Rx Traffic and interrupts on the NIC */
7296 if (start_nic(sp)) {
7297 DBG_PRINT(ERR_DBG, "%s: Starting NIC failed\n", dev->name);
7299 free_rx_buffers(sp);
7303 /* Add interrupt service routine */
7304 if (s2io_add_isr(sp) != 0) {
7305 if (sp->config.intr_type == MSI_X)
7308 free_rx_buffers(sp);
7312 S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2));
7314 /* Enable tasklet for the device */
7315 tasklet_init(&sp->task, s2io_tasklet, (unsigned long) dev);
7317 /* Enable select interrupts */
7318 en_dis_err_alarms(sp, ENA_ALL_INTRS, ENABLE_INTRS);
7319 if (sp->config.intr_type != INTA)
7320 en_dis_able_nic_intrs(sp, ENA_ALL_INTRS, DISABLE_INTRS);
7322 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
7323 interruptible |= TX_PIC_INTR;
7324 en_dis_able_nic_intrs(sp, interruptible, ENABLE_INTRS);
7327 set_bit(__S2IO_STATE_CARD_UP, &sp->state);
7332 * s2io_restart_nic - Resets the NIC.
7333 * @data : long pointer to the device private structure
7335 * This function is scheduled to be run by the s2io_tx_watchdog
7336 * function after 0.5 secs to reset the NIC. The idea is to reduce
7337 * the run time of the watch dog routine which is run holding a
7341 static void s2io_restart_nic(struct work_struct *work)
7343 struct s2io_nic *sp = container_of(work, struct s2io_nic, rst_timer_task);
7344 struct net_device *dev = sp->dev;
7348 if (!netif_running(dev))
7352 if (s2io_card_up(sp)) {
7353 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
7356 s2io_wake_all_tx_queue(sp);
7357 DBG_PRINT(ERR_DBG, "%s: was reset by Tx watchdog timer\n",
7364 * s2io_tx_watchdog - Watchdog for transmit side.
7365 * @dev : Pointer to net device structure
7367 * This function is triggered if the Tx Queue is stopped
7368 * for a pre-defined amount of time when the Interface is still up.
7369 * If the Interface is jammed in such a situation, the hardware is
7370 * reset (by s2io_close) and restarted again (by s2io_open) to
7371 * overcome any problem that might have been caused in the hardware.
7376 static void s2io_tx_watchdog(struct net_device *dev)
7378 struct s2io_nic *sp = dev->priv;
7380 if (netif_carrier_ok(dev)) {
7381 sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt++;
7382 schedule_work(&sp->rst_timer_task);
7383 sp->mac_control.stats_info->sw_stat.soft_reset_cnt++;
7388 * rx_osm_handler - To perform some OS related operations on SKB.
7389 * @sp: private member of the device structure,pointer to s2io_nic structure.
7390 * @skb : the socket buffer pointer.
7391 * @len : length of the packet
7392 * @cksum : FCS checksum of the frame.
7393 * @ring_no : the ring from which this RxD was extracted.
7395 * This function is called by the Rx interrupt serivce routine to perform
7396 * some OS related operations on the SKB before passing it to the upper
7397 * layers. It mainly checks if the checksum is OK, if so adds it to the
7398 * SKBs cksum variable, increments the Rx packet count and passes the SKB
7399 * to the upper layer. If the checksum is wrong, it increments the Rx
7400 * packet error count, frees the SKB and returns error.
7402 * SUCCESS on success and -1 on failure.
7404 static int rx_osm_handler(struct ring_info *ring_data, struct RxD_t * rxdp)
7406 struct s2io_nic *sp = ring_data->nic;
7407 struct net_device *dev = (struct net_device *) sp->dev;
7408 struct sk_buff *skb = (struct sk_buff *)
7409 ((unsigned long) rxdp->Host_Control);
7410 int ring_no = ring_data->ring_no;
7411 u16 l3_csum, l4_csum;
7412 unsigned long long err = rxdp->Control_1 & RXD_T_CODE;
7419 /* Check for parity error */
7421 sp->mac_control.stats_info->sw_stat.parity_err_cnt++;
7423 err_mask = err >> 48;
7426 sp->mac_control.stats_info->sw_stat.
7427 rx_parity_err_cnt++;
7431 sp->mac_control.stats_info->sw_stat.
7436 sp->mac_control.stats_info->sw_stat.
7437 rx_parity_abort_cnt++;
7441 sp->mac_control.stats_info->sw_stat.
7446 sp->mac_control.stats_info->sw_stat.
7451 sp->mac_control.stats_info->sw_stat.
7456 sp->mac_control.stats_info->sw_stat.
7457 rx_buf_size_err_cnt++;
7461 sp->mac_control.stats_info->sw_stat.
7462 rx_rxd_corrupt_cnt++;
7466 sp->mac_control.stats_info->sw_stat.
7471 * Drop the packet if bad transfer code. Exception being
7472 * 0x5, which could be due to unsupported IPv6 extension header.
7473 * In this case, we let stack handle the packet.
7474 * Note that in this case, since checksum will be incorrect,
7475 * stack will validate the same.
7477 if (err_mask != 0x5) {
7478 DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%x\n",
7479 dev->name, err_mask);
7480 sp->stats.rx_crc_errors++;
7481 sp->mac_control.stats_info->sw_stat.mem_freed
7484 atomic_dec(&sp->rx_bufs_left[ring_no]);
7485 rxdp->Host_Control = 0;
7490 /* Updating statistics */
7491 sp->stats.rx_packets++;
7492 rxdp->Host_Control = 0;
7493 if (sp->rxd_mode == RXD_MODE_1) {
7494 int len = RXD_GET_BUFFER0_SIZE_1(rxdp->Control_2);
7496 sp->stats.rx_bytes += len;
7499 } else if (sp->rxd_mode == RXD_MODE_3B) {
7500 int get_block = ring_data->rx_curr_get_info.block_index;
7501 int get_off = ring_data->rx_curr_get_info.offset;
7502 int buf0_len = RXD_GET_BUFFER0_SIZE_3(rxdp->Control_2);
7503 int buf2_len = RXD_GET_BUFFER2_SIZE_3(rxdp->Control_2);
7504 unsigned char *buff = skb_push(skb, buf0_len);
7506 struct buffAdd *ba = &ring_data->ba[get_block][get_off];
7507 sp->stats.rx_bytes += buf0_len + buf2_len;
7508 memcpy(buff, ba->ba_0, buf0_len);
7509 skb_put(skb, buf2_len);
7512 if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) && ((!sp->lro) ||
7513 (sp->lro && (!(rxdp->Control_1 & RXD_FRAME_IP_FRAG)))) &&
7515 l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1);
7516 l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1);
7517 if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) {
7519 * NIC verifies if the Checksum of the received
7520 * frame is Ok or not and accordingly returns
7521 * a flag in the RxD.
7523 skb->ip_summed = CHECKSUM_UNNECESSARY;
7529 ret = s2io_club_tcp_session(skb->data, &tcp,
7533 case 3: /* Begin anew */
7536 case 1: /* Aggregate */
7538 lro_append_pkt(sp, lro,
7542 case 4: /* Flush session */
7544 lro_append_pkt(sp, lro,
7546 queue_rx_frame(lro->parent,
7548 clear_lro_session(lro);
7549 sp->mac_control.stats_info->
7550 sw_stat.flush_max_pkts++;
7553 case 2: /* Flush both */
7554 lro->parent->data_len =
7556 sp->mac_control.stats_info->
7557 sw_stat.sending_both++;
7558 queue_rx_frame(lro->parent,
7560 clear_lro_session(lro);
7562 case 0: /* sessions exceeded */
7563 case -1: /* non-TCP or not
7567 * First pkt in session not
7568 * L3/L4 aggregatable
7573 "%s: Samadhana!!\n",
7580 * Packet with erroneous checksum, let the
7581 * upper layers deal with it.
7583 skb->ip_summed = CHECKSUM_NONE;
7586 skb->ip_summed = CHECKSUM_NONE;
7588 sp->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
7590 queue_rx_frame(skb, RXD_GET_VLAN_TAG(rxdp->Control_2));
7591 dev->last_rx = jiffies;
7593 atomic_dec(&sp->rx_bufs_left[ring_no]);
7598 * s2io_link - stops/starts the Tx queue.
7599 * @sp : private member of the device structure, which is a pointer to the
7600 * s2io_nic structure.
7601 * @link : inidicates whether link is UP/DOWN.
7603 * This function stops/starts the Tx queue depending on whether the link
7604 * status of the NIC is is down or up. This is called by the Alarm
7605 * interrupt handler whenever a link change interrupt comes up.
7610 static void s2io_link(struct s2io_nic * sp, int link)
7612 struct net_device *dev = (struct net_device *) sp->dev;
7614 if (link != sp->last_link_state) {
7616 if (link == LINK_DOWN) {
7617 DBG_PRINT(ERR_DBG, "%s: Link down\n", dev->name);
7618 s2io_stop_all_tx_queue(sp);
7619 netif_carrier_off(dev);
7620 if(sp->mac_control.stats_info->sw_stat.link_up_cnt)
7621 sp->mac_control.stats_info->sw_stat.link_up_time =
7622 jiffies - sp->start_time;
7623 sp->mac_control.stats_info->sw_stat.link_down_cnt++;
7625 DBG_PRINT(ERR_DBG, "%s: Link Up\n", dev->name);
7626 if (sp->mac_control.stats_info->sw_stat.link_down_cnt)
7627 sp->mac_control.stats_info->sw_stat.link_down_time =
7628 jiffies - sp->start_time;
7629 sp->mac_control.stats_info->sw_stat.link_up_cnt++;
7630 netif_carrier_on(dev);
7631 s2io_wake_all_tx_queue(sp);
7634 sp->last_link_state = link;
7635 sp->start_time = jiffies;
7639 * s2io_init_pci -Initialization of PCI and PCI-X configuration registers .
7640 * @sp : private member of the device structure, which is a pointer to the
7641 * s2io_nic structure.
7643 * This function initializes a few of the PCI and PCI-X configuration registers
7644 * with recommended values.
7649 static void s2io_init_pci(struct s2io_nic * sp)
7651 u16 pci_cmd = 0, pcix_cmd = 0;
7653 /* Enable Data Parity Error Recovery in PCI-X command register. */
7654 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7656 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7658 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7661 /* Set the PErr Response bit in PCI command register. */
7662 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7663 pci_write_config_word(sp->pdev, PCI_COMMAND,
7664 (pci_cmd | PCI_COMMAND_PARITY));
7665 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7668 static int s2io_verify_parm(struct pci_dev *pdev, u8 *dev_intr_type,
7671 if ((tx_fifo_num > MAX_TX_FIFOS) ||
7672 (tx_fifo_num < 1)) {
7673 DBG_PRINT(ERR_DBG, "s2io: Requested number of tx fifos "
7674 "(%d) not supported\n", tx_fifo_num);
7676 if (tx_fifo_num < 1)
7679 tx_fifo_num = MAX_TX_FIFOS;
7681 DBG_PRINT(ERR_DBG, "s2io: Default to %d ", tx_fifo_num);
7682 DBG_PRINT(ERR_DBG, "tx fifos\n");
7685 #ifndef CONFIG_NETDEVICES_MULTIQUEUE
7687 DBG_PRINT(ERR_DBG, "s2io: Multiqueue support not enabled\n");
7692 *dev_multiq = multiq;
7694 if (tx_steering_type && (1 == tx_fifo_num)) {
7695 if (tx_steering_type != TX_DEFAULT_STEERING)
7697 "s2io: Tx steering is not supported with "
7698 "one fifo. Disabling Tx steering.\n");
7699 tx_steering_type = NO_STEERING;
7702 if ((tx_steering_type < NO_STEERING) ||
7703 (tx_steering_type > TX_DEFAULT_STEERING)) {
7704 DBG_PRINT(ERR_DBG, "s2io: Requested transmit steering not "
7706 DBG_PRINT(ERR_DBG, "s2io: Disabling transmit steering\n");
7707 tx_steering_type = NO_STEERING;
7710 if ( rx_ring_num > 8) {
7711 DBG_PRINT(ERR_DBG, "s2io: Requested number of Rx rings not "
7713 DBG_PRINT(ERR_DBG, "s2io: Default to 8 Rx rings\n");
7716 if (*dev_intr_type != INTA)
7719 if ((*dev_intr_type != INTA) && (*dev_intr_type != MSI_X)) {
7720 DBG_PRINT(ERR_DBG, "s2io: Wrong intr_type requested. "
7721 "Defaulting to INTA\n");
7722 *dev_intr_type = INTA;
7725 if ((*dev_intr_type == MSI_X) &&
7726 ((pdev->device != PCI_DEVICE_ID_HERC_WIN) &&
7727 (pdev->device != PCI_DEVICE_ID_HERC_UNI))) {
7728 DBG_PRINT(ERR_DBG, "s2io: Xframe I does not support MSI_X. "
7729 "Defaulting to INTA\n");
7730 *dev_intr_type = INTA;
7733 if ((rx_ring_mode != 1) && (rx_ring_mode != 2)) {
7734 DBG_PRINT(ERR_DBG, "s2io: Requested ring mode not supported\n");
7735 DBG_PRINT(ERR_DBG, "s2io: Defaulting to 1-buffer mode\n");
7742 * rts_ds_steer - Receive traffic steering based on IPv4 or IPv6 TOS
7743 * or Traffic class respectively.
7744 * @nic: device private variable
7745 * Description: The function configures the receive steering to
7746 * desired receive ring.
7747 * Return Value: SUCCESS on success and
7748 * '-1' on failure (endian settings incorrect).
7750 static int rts_ds_steer(struct s2io_nic *nic, u8 ds_codepoint, u8 ring)
7752 struct XENA_dev_config __iomem *bar0 = nic->bar0;
7753 register u64 val64 = 0;
7755 if (ds_codepoint > 63)
7758 val64 = RTS_DS_MEM_DATA(ring);
7759 writeq(val64, &bar0->rts_ds_mem_data);
7761 val64 = RTS_DS_MEM_CTRL_WE |
7762 RTS_DS_MEM_CTRL_STROBE_NEW_CMD |
7763 RTS_DS_MEM_CTRL_OFFSET(ds_codepoint);
7765 writeq(val64, &bar0->rts_ds_mem_ctrl);
7767 return wait_for_cmd_complete(&bar0->rts_ds_mem_ctrl,
7768 RTS_DS_MEM_CTRL_STROBE_CMD_BEING_EXECUTED,
7773 * s2io_init_nic - Initialization of the adapter .
7774 * @pdev : structure containing the PCI related information of the device.
7775 * @pre: List of PCI devices supported by the driver listed in s2io_tbl.
7777 * The function initializes an adapter identified by the pci_dec structure.
7778 * All OS related initialization including memory and device structure and
7779 * initlaization of the device private variable is done. Also the swapper
7780 * control register is initialized to enable read and write into the I/O
7781 * registers of the device.
7783 * returns 0 on success and negative on failure.
7786 static int __devinit
7787 s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
7789 struct s2io_nic *sp;
7790 struct net_device *dev;
7792 int dma_flag = FALSE;
7793 u32 mac_up, mac_down;
7794 u64 val64 = 0, tmp64 = 0;
7795 struct XENA_dev_config __iomem *bar0 = NULL;
7797 struct mac_info *mac_control;
7798 struct config_param *config;
7800 u8 dev_intr_type = intr_type;
7802 DECLARE_MAC_BUF(mac);
7804 ret = s2io_verify_parm(pdev, &dev_intr_type, &dev_multiq);
7808 if ((ret = pci_enable_device(pdev))) {
7810 "s2io_init_nic: pci_enable_device failed\n");
7814 if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
7815 DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 64bit DMA\n");
7817 if (pci_set_consistent_dma_mask
7818 (pdev, DMA_64BIT_MASK)) {
7820 "Unable to obtain 64bit DMA for \
7821 consistent allocations\n");
7822 pci_disable_device(pdev);
7825 } else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
7826 DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 32bit DMA\n");
7828 pci_disable_device(pdev);
7831 if ((ret = pci_request_regions(pdev, s2io_driver_name))) {
7832 DBG_PRINT(ERR_DBG, "%s: Request Regions failed - %x \n", __FUNCTION__, ret);
7833 pci_disable_device(pdev);
7836 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
7838 dev = alloc_etherdev_mq(sizeof(struct s2io_nic), tx_fifo_num);
7841 dev = alloc_etherdev(sizeof(struct s2io_nic));
7843 DBG_PRINT(ERR_DBG, "Device allocation failed\n");
7844 pci_disable_device(pdev);
7845 pci_release_regions(pdev);
7849 pci_set_master(pdev);
7850 pci_set_drvdata(pdev, dev);
7851 SET_NETDEV_DEV(dev, &pdev->dev);
7853 /* Private member variable initialized to s2io NIC structure */
7855 memset(sp, 0, sizeof(struct s2io_nic));
7858 sp->high_dma_flag = dma_flag;
7859 sp->device_enabled_once = FALSE;
7860 if (rx_ring_mode == 1)
7861 sp->rxd_mode = RXD_MODE_1;
7862 if (rx_ring_mode == 2)
7863 sp->rxd_mode = RXD_MODE_3B;
7865 sp->config.intr_type = dev_intr_type;
7867 if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) ||
7868 (pdev->device == PCI_DEVICE_ID_HERC_UNI))
7869 sp->device_type = XFRAME_II_DEVICE;
7871 sp->device_type = XFRAME_I_DEVICE;
7873 sp->lro = lro_enable;
7875 /* Initialize some PCI/PCI-X fields of the NIC. */
7879 * Setting the device configuration parameters.
7880 * Most of these parameters can be specified by the user during
7881 * module insertion as they are module loadable parameters. If
7882 * these parameters are not not specified during load time, they
7883 * are initialized with default values.
7885 mac_control = &sp->mac_control;
7886 config = &sp->config;
7888 config->napi = napi;
7889 config->tx_steering_type = tx_steering_type;
7891 /* Tx side parameters. */
7892 if (config->tx_steering_type == TX_PRIORITY_STEERING)
7893 config->tx_fifo_num = MAX_TX_FIFOS;
7895 config->tx_fifo_num = tx_fifo_num;
7897 /* Initialize the fifos used for tx steering */
7898 if (config->tx_fifo_num < 5) {
7899 if (config->tx_fifo_num == 1)
7900 sp->total_tcp_fifos = 1;
7902 sp->total_tcp_fifos = config->tx_fifo_num - 1;
7903 sp->udp_fifo_idx = config->tx_fifo_num - 1;
7904 sp->total_udp_fifos = 1;
7905 sp->other_fifo_idx = sp->total_tcp_fifos - 1;
7907 sp->total_tcp_fifos = (tx_fifo_num - FIFO_UDP_MAX_NUM -
7908 FIFO_OTHER_MAX_NUM);
7909 sp->udp_fifo_idx = sp->total_tcp_fifos;
7910 sp->total_udp_fifos = FIFO_UDP_MAX_NUM;
7911 sp->other_fifo_idx = sp->udp_fifo_idx + FIFO_UDP_MAX_NUM;
7914 config->multiq = dev_multiq;
7915 for (i = 0; i < config->tx_fifo_num; i++) {
7916 config->tx_cfg[i].fifo_len = tx_fifo_len[i];
7917 config->tx_cfg[i].fifo_priority = i;
7920 /* mapping the QoS priority to the configured fifos */
7921 for (i = 0; i < MAX_TX_FIFOS; i++)
7922 config->fifo_mapping[i] = fifo_map[config->tx_fifo_num - 1][i];
7924 /* map the hashing selector table to the configured fifos */
7925 for (i = 0; i < config->tx_fifo_num; i++)
7926 sp->fifo_selector[i] = fifo_selector[i];
7929 config->tx_intr_type = TXD_INT_TYPE_UTILZ;
7930 for (i = 0; i < config->tx_fifo_num; i++) {
7931 config->tx_cfg[i].f_no_snoop =
7932 (NO_SNOOP_TXD | NO_SNOOP_TXD_BUFFER);
7933 if (config->tx_cfg[i].fifo_len < 65) {
7934 config->tx_intr_type = TXD_INT_TYPE_PER_LIST;
7938 /* + 2 because one Txd for skb->data and one Txd for UFO */
7939 config->max_txds = MAX_SKB_FRAGS + 2;
7941 /* Rx side parameters. */
7942 config->rx_ring_num = rx_ring_num;
7943 for (i = 0; i < MAX_RX_RINGS; i++) {
7944 config->rx_cfg[i].num_rxd = rx_ring_sz[i] *
7945 (rxd_count[sp->rxd_mode] + 1);
7946 config->rx_cfg[i].ring_priority = i;
7949 for (i = 0; i < rx_ring_num; i++) {
7950 config->rx_cfg[i].ring_org = RING_ORG_BUFF1;
7951 config->rx_cfg[i].f_no_snoop =
7952 (NO_SNOOP_RXD | NO_SNOOP_RXD_BUFFER);
7955 /* Setting Mac Control parameters */
7956 mac_control->rmac_pause_time = rmac_pause_time;
7957 mac_control->mc_pause_threshold_q0q3 = mc_pause_threshold_q0q3;
7958 mac_control->mc_pause_threshold_q4q7 = mc_pause_threshold_q4q7;
7961 /* Initialize Ring buffer parameters. */
7962 for (i = 0; i < config->rx_ring_num; i++)
7963 atomic_set(&sp->rx_bufs_left[i], 0);
7965 /* initialize the shared memory used by the NIC and the host */
7966 if (init_shared_mem(sp)) {
7967 DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n",
7970 goto mem_alloc_failed;
7973 sp->bar0 = ioremap(pci_resource_start(pdev, 0),
7974 pci_resource_len(pdev, 0));
7976 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem1\n",
7979 goto bar0_remap_failed;
7982 sp->bar1 = ioremap(pci_resource_start(pdev, 2),
7983 pci_resource_len(pdev, 2));
7985 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem2\n",
7988 goto bar1_remap_failed;
7991 dev->irq = pdev->irq;
7992 dev->base_addr = (unsigned long) sp->bar0;
7994 /* Initializing the BAR1 address as the start of the FIFO pointer. */
7995 for (j = 0; j < MAX_TX_FIFOS; j++) {
7996 mac_control->tx_FIFO_start[j] = (struct TxFIFO_element __iomem *)
7997 (sp->bar1 + (j * 0x00020000));
8000 /* Driver entry points */
8001 dev->open = &s2io_open;
8002 dev->stop = &s2io_close;
8003 dev->hard_start_xmit = &s2io_xmit;
8004 dev->get_stats = &s2io_get_stats;
8005 dev->set_multicast_list = &s2io_set_multicast;
8006 dev->do_ioctl = &s2io_ioctl;
8007 dev->set_mac_address = &s2io_set_mac_addr;
8008 dev->change_mtu = &s2io_change_mtu;
8009 SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
8010 dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
8011 dev->vlan_rx_register = s2io_vlan_rx_register;
8012 dev->vlan_rx_kill_vid = (void *)s2io_vlan_rx_kill_vid;
8015 * will use eth_mac_addr() for dev->set_mac_address
8016 * mac address will be set every time dev->open() is called
8018 netif_napi_add(dev, &sp->napi, s2io_poll, 32);
8020 #ifdef CONFIG_NET_POLL_CONTROLLER
8021 dev->poll_controller = s2io_netpoll;
8024 dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
8025 if (sp->high_dma_flag == TRUE)
8026 dev->features |= NETIF_F_HIGHDMA;
8027 dev->features |= NETIF_F_TSO;
8028 dev->features |= NETIF_F_TSO6;
8029 if ((sp->device_type & XFRAME_II_DEVICE) && (ufo)) {
8030 dev->features |= NETIF_F_UFO;
8031 dev->features |= NETIF_F_HW_CSUM;
8033 #ifdef CONFIG_NETDEVICES_MULTIQUEUE
8035 dev->features |= NETIF_F_MULTI_QUEUE;
8037 dev->tx_timeout = &s2io_tx_watchdog;
8038 dev->watchdog_timeo = WATCH_DOG_TIMEOUT;
8039 INIT_WORK(&sp->rst_timer_task, s2io_restart_nic);
8040 INIT_WORK(&sp->set_link_task, s2io_set_link);
8042 pci_save_state(sp->pdev);
8044 /* Setting swapper control on the NIC, for proper reset operation */
8045 if (s2io_set_swapper(sp)) {
8046 DBG_PRINT(ERR_DBG, "%s:swapper settings are wrong\n",
8049 goto set_swap_failed;
8052 /* Verify if the Herc works on the slot its placed into */
8053 if (sp->device_type & XFRAME_II_DEVICE) {
8054 mode = s2io_verify_pci_mode(sp);
8056 DBG_PRINT(ERR_DBG, "%s: ", __FUNCTION__);
8057 DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
8059 goto set_swap_failed;
8063 /* Not needed for Herc */
8064 if (sp->device_type & XFRAME_I_DEVICE) {
8066 * Fix for all "FFs" MAC address problems observed on
8069 fix_mac_address(sp);
8074 * MAC address initialization.
8075 * For now only one mac address will be read and used.
8078 val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
8079 RMAC_ADDR_CMD_MEM_OFFSET(0 + S2IO_MAC_ADDR_START_OFFSET);
8080 writeq(val64, &bar0->rmac_addr_cmd_mem);
8081 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
8082 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING, S2IO_BIT_RESET);
8083 tmp64 = readq(&bar0->rmac_addr_data0_mem);
8084 mac_down = (u32) tmp64;
8085 mac_up = (u32) (tmp64 >> 32);
8087 sp->def_mac_addr[0].mac_addr[3] = (u8) (mac_up);
8088 sp->def_mac_addr[0].mac_addr[2] = (u8) (mac_up >> 8);
8089 sp->def_mac_addr[0].mac_addr[1] = (u8) (mac_up >> 16);
8090 sp->def_mac_addr[0].mac_addr[0] = (u8) (mac_up >> 24);
8091 sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16);
8092 sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24);
8094 /* Set the factory defined MAC address initially */
8095 dev->addr_len = ETH_ALEN;
8096 memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN);
8097 memcpy(dev->perm_addr, dev->dev_addr, ETH_ALEN);
8099 /* initialize number of multicast & unicast MAC entries variables */
8100 if (sp->device_type == XFRAME_I_DEVICE) {
8101 config->max_mc_addr = S2IO_XENA_MAX_MC_ADDRESSES;
8102 config->max_mac_addr = S2IO_XENA_MAX_MAC_ADDRESSES;
8103 config->mc_start_offset = S2IO_XENA_MC_ADDR_START_OFFSET;
8104 } else if (sp->device_type == XFRAME_II_DEVICE) {
8105 config->max_mc_addr = S2IO_HERC_MAX_MC_ADDRESSES;
8106 config->max_mac_addr = S2IO_HERC_MAX_MAC_ADDRESSES;
8107 config->mc_start_offset = S2IO_HERC_MC_ADDR_START_OFFSET;
8110 /* store mac addresses from CAM to s2io_nic structure */
8111 do_s2io_store_unicast_mc(sp);
8113 /* Store the values of the MSIX table in the s2io_nic structure */
8114 store_xmsi_data(sp);
8115 /* reset Nic and bring it to known state */
8119 * Initialize the tasklet status and link state flags
8120 * and the card state parameter
8122 sp->tasklet_status = 0;
8125 /* Initialize spinlocks */
8126 for (i = 0; i < sp->config.tx_fifo_num; i++)
8127 spin_lock_init(&mac_control->fifos[i].tx_lock);
8130 spin_lock_init(&sp->put_lock);
8131 spin_lock_init(&sp->rx_lock);
8134 * SXE-002: Configure link and activity LED to init state
8137 subid = sp->pdev->subsystem_device;
8138 if ((subid & 0xFF) >= 0x07) {
8139 val64 = readq(&bar0->gpio_control);
8140 val64 |= 0x0000800000000000ULL;
8141 writeq(val64, &bar0->gpio_control);
8142 val64 = 0x0411040400000000ULL;
8143 writeq(val64, (void __iomem *) bar0 + 0x2700);
8144 val64 = readq(&bar0->gpio_control);
8147 sp->rx_csum = 1; /* Rx chksum verify enabled by default */
8149 if (register_netdev(dev)) {
8150 DBG_PRINT(ERR_DBG, "Device registration failed\n");
8152 goto register_failed;
8155 DBG_PRINT(ERR_DBG, "Copyright(c) 2002-2007 Neterion Inc.\n");
8156 DBG_PRINT(ERR_DBG, "%s: Neterion %s (rev %d)\n",dev->name,
8157 sp->product_name, pdev->revision);
8158 DBG_PRINT(ERR_DBG, "%s: Driver version %s\n", dev->name,
8159 s2io_driver_version);
8160 DBG_PRINT(ERR_DBG, "%s: MAC ADDR: %s\n",
8161 dev->name, print_mac(mac, dev->dev_addr));
8162 DBG_PRINT(ERR_DBG, "SERIAL NUMBER: %s\n", sp->serial_num);
8163 if (sp->device_type & XFRAME_II_DEVICE) {
8164 mode = s2io_print_pci_mode(sp);
8166 DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
8168 unregister_netdev(dev);
8169 goto set_swap_failed;
8172 switch(sp->rxd_mode) {
8174 DBG_PRINT(ERR_DBG, "%s: 1-Buffer receive mode enabled\n",
8178 DBG_PRINT(ERR_DBG, "%s: 2-Buffer receive mode enabled\n",
8184 DBG_PRINT(ERR_DBG, "%s: NAPI enabled\n", dev->name);
8186 DBG_PRINT(ERR_DBG, "%s: Using %d Tx fifo(s)\n", dev->name,
8187 sp->config.tx_fifo_num);
8189 switch(sp->config.intr_type) {
8191 DBG_PRINT(ERR_DBG, "%s: Interrupt type INTA\n", dev->name);
8194 DBG_PRINT(ERR_DBG, "%s: Interrupt type MSI-X\n", dev->name);
8197 if (sp->config.multiq) {
8198 for (i = 0; i < sp->config.tx_fifo_num; i++)
8199 mac_control->fifos[i].multiq = config->multiq;
8200 DBG_PRINT(ERR_DBG, "%s: Multiqueue support enabled\n",
8203 DBG_PRINT(ERR_DBG, "%s: Multiqueue support disabled\n",
8206 switch (sp->config.tx_steering_type) {
8208 DBG_PRINT(ERR_DBG, "%s: No steering enabled for"
8209 " transmit\n", dev->name);
8211 case TX_PRIORITY_STEERING:
8212 DBG_PRINT(ERR_DBG, "%s: Priority steering enabled for"
8213 " transmit\n", dev->name);
8215 case TX_DEFAULT_STEERING:
8216 DBG_PRINT(ERR_DBG, "%s: Default steering enabled for"
8217 " transmit\n", dev->name);
8221 DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
8224 DBG_PRINT(ERR_DBG, "%s: UDP Fragmentation Offload(UFO)"
8225 " enabled\n", dev->name);
8226 /* Initialize device name */
8227 sprintf(sp->name, "%s Neterion %s", dev->name, sp->product_name);
8230 * Make Link state as off at this point, when the Link change
8231 * interrupt comes the state will be automatically changed to
8234 netif_carrier_off(dev);
8245 free_shared_mem(sp);
8246 pci_disable_device(pdev);
8247 pci_release_regions(pdev);
8248 pci_set_drvdata(pdev, NULL);
8255 * s2io_rem_nic - Free the PCI device
8256 * @pdev: structure containing the PCI related information of the device.
8257 * Description: This function is called by the Pci subsystem to release a
8258 * PCI device and free up all resource held up by the device. This could
8259 * be in response to a Hot plug event or when the driver is to be removed
8263 static void __devexit s2io_rem_nic(struct pci_dev *pdev)
8265 struct net_device *dev =
8266 (struct net_device *) pci_get_drvdata(pdev);
8267 struct s2io_nic *sp;
8270 DBG_PRINT(ERR_DBG, "Driver Data is NULL!!\n");
8274 flush_scheduled_work();
8277 unregister_netdev(dev);
8279 free_shared_mem(sp);
8282 pci_release_regions(pdev);
8283 pci_set_drvdata(pdev, NULL);
8285 pci_disable_device(pdev);
8289 * s2io_starter - Entry point for the driver
8290 * Description: This function is the entry point for the driver. It verifies
8291 * the module loadable parameters and initializes PCI configuration space.
8294 static int __init s2io_starter(void)
8296 return pci_register_driver(&s2io_driver);
8300 * s2io_closer - Cleanup routine for the driver
8301 * Description: This function is the cleanup routine for the driver. It unregist * ers the driver.
8304 static __exit void s2io_closer(void)
8306 pci_unregister_driver(&s2io_driver);
8307 DBG_PRINT(INIT_DBG, "cleanup done\n");
8310 module_init(s2io_starter);
8311 module_exit(s2io_closer);
8313 static int check_L2_lro_capable(u8 *buffer, struct iphdr **ip,
8314 struct tcphdr **tcp, struct RxD_t *rxdp,
8315 struct s2io_nic *sp)
8318 u8 l2_type = (u8)((rxdp->Control_1 >> 37) & 0x7), ip_len;
8320 if (!(rxdp->Control_1 & RXD_FRAME_PROTO_TCP)) {
8321 DBG_PRINT(INIT_DBG,"%s: Non-TCP frames not supported for LRO\n",
8326 /* Checking for DIX type or DIX type with VLAN */
8328 || (l2_type == 4)) {
8329 ip_off = HEADER_ETHERNET_II_802_3_SIZE;
8331 * If vlan stripping is disabled and the frame is VLAN tagged,
8332 * shift the offset by the VLAN header size bytes.
8334 if ((!vlan_strip_flag) &&
8335 (rxdp->Control_1 & RXD_FRAME_VLAN_TAG))
8336 ip_off += HEADER_VLAN_SIZE;
8338 /* LLC, SNAP etc are considered non-mergeable */
8342 *ip = (struct iphdr *)((u8 *)buffer + ip_off);
8343 ip_len = (u8)((*ip)->ihl);
8345 *tcp = (struct tcphdr *)((unsigned long)*ip + ip_len);
8350 static int check_for_socket_match(struct lro *lro, struct iphdr *ip,
8353 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8354 if ((lro->iph->saddr != ip->saddr) || (lro->iph->daddr != ip->daddr) ||
8355 (lro->tcph->source != tcp->source) || (lro->tcph->dest != tcp->dest))
8360 static inline int get_l4_pyld_length(struct iphdr *ip, struct tcphdr *tcp)
8362 return(ntohs(ip->tot_len) - (ip->ihl << 2) - (tcp->doff << 2));
8365 static void initiate_new_session(struct lro *lro, u8 *l2h,
8366 struct iphdr *ip, struct tcphdr *tcp, u32 tcp_pyld_len, u16 vlan_tag)
8368 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8372 lro->tcp_next_seq = tcp_pyld_len + ntohl(tcp->seq);
8373 lro->tcp_ack = tcp->ack_seq;
8375 lro->total_len = ntohs(ip->tot_len);
8377 lro->vlan_tag = vlan_tag;
8379 * check if we saw TCP timestamp. Other consistency checks have
8380 * already been done.
8382 if (tcp->doff == 8) {
8384 ptr = (__be32 *)(tcp+1);
8386 lro->cur_tsval = ntohl(*(ptr+1));
8387 lro->cur_tsecr = *(ptr+2);
8392 static void update_L3L4_header(struct s2io_nic *sp, struct lro *lro)
8394 struct iphdr *ip = lro->iph;
8395 struct tcphdr *tcp = lro->tcph;
8397 struct stat_block *statinfo = sp->mac_control.stats_info;
8398 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8400 /* Update L3 header */
8401 ip->tot_len = htons(lro->total_len);
8403 nchk = ip_fast_csum((u8 *)lro->iph, ip->ihl);
8406 /* Update L4 header */
8407 tcp->ack_seq = lro->tcp_ack;
8408 tcp->window = lro->window;
8410 /* Update tsecr field if this session has timestamps enabled */
8412 __be32 *ptr = (__be32 *)(tcp + 1);
8413 *(ptr+2) = lro->cur_tsecr;
8416 /* Update counters required for calculation of
8417 * average no. of packets aggregated.
8419 statinfo->sw_stat.sum_avg_pkts_aggregated += lro->sg_num;
8420 statinfo->sw_stat.num_aggregations++;
8423 static void aggregate_new_rx(struct lro *lro, struct iphdr *ip,
8424 struct tcphdr *tcp, u32 l4_pyld)
8426 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8427 lro->total_len += l4_pyld;
8428 lro->frags_len += l4_pyld;
8429 lro->tcp_next_seq += l4_pyld;
8432 /* Update ack seq no. and window ad(from this pkt) in LRO object */
8433 lro->tcp_ack = tcp->ack_seq;
8434 lro->window = tcp->window;
8438 /* Update tsecr and tsval from this packet */
8439 ptr = (__be32 *)(tcp+1);
8440 lro->cur_tsval = ntohl(*(ptr+1));
8441 lro->cur_tsecr = *(ptr + 2);
8445 static int verify_l3_l4_lro_capable(struct lro *l_lro, struct iphdr *ip,
8446 struct tcphdr *tcp, u32 tcp_pyld_len)
8450 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
8452 if (!tcp_pyld_len) {
8453 /* Runt frame or a pure ack */
8457 if (ip->ihl != 5) /* IP has options */
8460 /* If we see CE codepoint in IP header, packet is not mergeable */
8461 if (INET_ECN_is_ce(ipv4_get_dsfield(ip)))
8464 /* If we see ECE or CWR flags in TCP header, packet is not mergeable */
8465 if (tcp->urg || tcp->psh || tcp->rst || tcp->syn || tcp->fin ||
8466 tcp->ece || tcp->cwr || !tcp->ack) {
8468 * Currently recognize only the ack control word and
8469 * any other control field being set would result in
8470 * flushing the LRO session
8476 * Allow only one TCP timestamp option. Don't aggregate if
8477 * any other options are detected.
8479 if (tcp->doff != 5 && tcp->doff != 8)
8482 if (tcp->doff == 8) {
8483 ptr = (u8 *)(tcp + 1);
8484 while (*ptr == TCPOPT_NOP)
8486 if (*ptr != TCPOPT_TIMESTAMP || *(ptr+1) != TCPOLEN_TIMESTAMP)
8489 /* Ensure timestamp value increases monotonically */
8491 if (l_lro->cur_tsval > ntohl(*((__be32 *)(ptr+2))))
8494 /* timestamp echo reply should be non-zero */
8495 if (*((__be32 *)(ptr+6)) == 0)
8503 s2io_club_tcp_session(u8 *buffer, u8 **tcp, u32 *tcp_len, struct lro **lro,
8504 struct RxD_t *rxdp, struct s2io_nic *sp)
8507 struct tcphdr *tcph;
8511 if (!(ret = check_L2_lro_capable(buffer, &ip, (struct tcphdr **)tcp,
8513 DBG_PRINT(INFO_DBG,"IP Saddr: %x Daddr: %x\n",
8514 ip->saddr, ip->daddr);
8518 vlan_tag = RXD_GET_VLAN_TAG(rxdp->Control_2);
8519 tcph = (struct tcphdr *)*tcp;
8520 *tcp_len = get_l4_pyld_length(ip, tcph);
8521 for (i=0; i<MAX_LRO_SESSIONS; i++) {
8522 struct lro *l_lro = &sp->lro0_n[i];
8523 if (l_lro->in_use) {
8524 if (check_for_socket_match(l_lro, ip, tcph))
8526 /* Sock pair matched */
8529 if ((*lro)->tcp_next_seq != ntohl(tcph->seq)) {
8530 DBG_PRINT(INFO_DBG, "%s:Out of order. expected "
8531 "0x%x, actual 0x%x\n", __FUNCTION__,
8532 (*lro)->tcp_next_seq,
8535 sp->mac_control.stats_info->
8536 sw_stat.outof_sequence_pkts++;
8541 if (!verify_l3_l4_lro_capable(l_lro, ip, tcph,*tcp_len))
8542 ret = 1; /* Aggregate */
8544 ret = 2; /* Flush both */
8550 /* Before searching for available LRO objects,
8551 * check if the pkt is L3/L4 aggregatable. If not
8552 * don't create new LRO session. Just send this
8555 if (verify_l3_l4_lro_capable(NULL, ip, tcph, *tcp_len)) {
8559 for (i=0; i<MAX_LRO_SESSIONS; i++) {
8560 struct lro *l_lro = &sp->lro0_n[i];
8561 if (!(l_lro->in_use)) {
8563 ret = 3; /* Begin anew */
8569 if (ret == 0) { /* sessions exceeded */
8570 DBG_PRINT(INFO_DBG,"%s:All LRO sessions already in use\n",
8578 initiate_new_session(*lro, buffer, ip, tcph, *tcp_len,
8582 update_L3L4_header(sp, *lro);
8585 aggregate_new_rx(*lro, ip, tcph, *tcp_len);
8586 if ((*lro)->sg_num == sp->lro_max_aggr_per_sess) {
8587 update_L3L4_header(sp, *lro);
8588 ret = 4; /* Flush the LRO */
8592 DBG_PRINT(ERR_DBG,"%s:Dont know, can't say!!\n",
8600 static void clear_lro_session(struct lro *lro)
8602 static u16 lro_struct_size = sizeof(struct lro);
8604 memset(lro, 0, lro_struct_size);
8607 static void queue_rx_frame(struct sk_buff *skb, u16 vlan_tag)
8609 struct net_device *dev = skb->dev;
8610 struct s2io_nic *sp = dev->priv;
8612 skb->protocol = eth_type_trans(skb, dev);
8613 if (sp->vlgrp && vlan_tag
8614 && (vlan_strip_flag)) {
8615 /* Queueing the vlan frame to the upper layer */
8616 if (sp->config.napi)
8617 vlan_hwaccel_receive_skb(skb, sp->vlgrp, vlan_tag);
8619 vlan_hwaccel_rx(skb, sp->vlgrp, vlan_tag);
8621 if (sp->config.napi)
8622 netif_receive_skb(skb);
8628 static void lro_append_pkt(struct s2io_nic *sp, struct lro *lro,
8629 struct sk_buff *skb,
8632 struct sk_buff *first = lro->parent;
8634 first->len += tcp_len;
8635 first->data_len = lro->frags_len;
8636 skb_pull(skb, (skb->len - tcp_len));
8637 if (skb_shinfo(first)->frag_list)
8638 lro->last_frag->next = skb;
8640 skb_shinfo(first)->frag_list = skb;
8641 first->truesize += skb->truesize;
8642 lro->last_frag = skb;
8643 sp->mac_control.stats_info->sw_stat.clubbed_frms_cnt++;
8648 * s2io_io_error_detected - called when PCI error is detected
8649 * @pdev: Pointer to PCI device
8650 * @state: The current pci connection state
8652 * This function is called after a PCI bus error affecting
8653 * this device has been detected.
8655 static pci_ers_result_t s2io_io_error_detected(struct pci_dev *pdev,
8656 pci_channel_state_t state)
8658 struct net_device *netdev = pci_get_drvdata(pdev);
8659 struct s2io_nic *sp = netdev->priv;
8661 netif_device_detach(netdev);
8663 if (netif_running(netdev)) {
8664 /* Bring down the card, while avoiding PCI I/O */
8665 do_s2io_card_down(sp, 0);
8667 pci_disable_device(pdev);
8669 return PCI_ERS_RESULT_NEED_RESET;
8673 * s2io_io_slot_reset - called after the pci bus has been reset.
8674 * @pdev: Pointer to PCI device
8676 * Restart the card from scratch, as if from a cold-boot.
8677 * At this point, the card has exprienced a hard reset,
8678 * followed by fixups by BIOS, and has its config space
8679 * set up identically to what it was at cold boot.
8681 static pci_ers_result_t s2io_io_slot_reset(struct pci_dev *pdev)
8683 struct net_device *netdev = pci_get_drvdata(pdev);
8684 struct s2io_nic *sp = netdev->priv;
8686 if (pci_enable_device(pdev)) {
8687 printk(KERN_ERR "s2io: "
8688 "Cannot re-enable PCI device after reset.\n");
8689 return PCI_ERS_RESULT_DISCONNECT;
8692 pci_set_master(pdev);
8695 return PCI_ERS_RESULT_RECOVERED;
8699 * s2io_io_resume - called when traffic can start flowing again.
8700 * @pdev: Pointer to PCI device
8702 * This callback is called when the error recovery driver tells
8703 * us that its OK to resume normal operation.
8705 static void s2io_io_resume(struct pci_dev *pdev)
8707 struct net_device *netdev = pci_get_drvdata(pdev);
8708 struct s2io_nic *sp = netdev->priv;
8710 if (netif_running(netdev)) {
8711 if (s2io_card_up(sp)) {
8712 printk(KERN_ERR "s2io: "
8713 "Can't bring device back up after reset.\n");
8717 if (s2io_set_mac_addr(netdev, netdev->dev_addr) == FAILURE) {
8719 printk(KERN_ERR "s2io: "
8720 "Can't resetore mac addr after reset.\n");
8725 netif_device_attach(netdev);
8726 netif_wake_queue(netdev);