1 /*******************************************************************************
3 Intel PRO/1000 Linux driver
4 Copyright(c) 1999 - 2006 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 Linux NICS <linux.nics@intel.com>
24 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
27 *******************************************************************************/
30 #include <net/ip6_checksum.h>
32 char e1000_driver_name[] = "e1000";
33 static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
34 #ifndef CONFIG_E1000_NAPI
37 #define DRIVERNAPI "-NAPI"
39 #define DRV_VERSION "7.3.20-k2"DRIVERNAPI
40 char e1000_driver_version[] = DRV_VERSION;
41 static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
43 /* e1000_pci_tbl - PCI Device ID Table
45 * Last entry must be all 0s
48 * {PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
50 static struct pci_device_id e1000_pci_tbl[] = {
51 INTEL_E1000_ETHERNET_DEVICE(0x1000),
52 INTEL_E1000_ETHERNET_DEVICE(0x1001),
53 INTEL_E1000_ETHERNET_DEVICE(0x1004),
54 INTEL_E1000_ETHERNET_DEVICE(0x1008),
55 INTEL_E1000_ETHERNET_DEVICE(0x1009),
56 INTEL_E1000_ETHERNET_DEVICE(0x100C),
57 INTEL_E1000_ETHERNET_DEVICE(0x100D),
58 INTEL_E1000_ETHERNET_DEVICE(0x100E),
59 INTEL_E1000_ETHERNET_DEVICE(0x100F),
60 INTEL_E1000_ETHERNET_DEVICE(0x1010),
61 INTEL_E1000_ETHERNET_DEVICE(0x1011),
62 INTEL_E1000_ETHERNET_DEVICE(0x1012),
63 INTEL_E1000_ETHERNET_DEVICE(0x1013),
64 INTEL_E1000_ETHERNET_DEVICE(0x1014),
65 INTEL_E1000_ETHERNET_DEVICE(0x1015),
66 INTEL_E1000_ETHERNET_DEVICE(0x1016),
67 INTEL_E1000_ETHERNET_DEVICE(0x1017),
68 INTEL_E1000_ETHERNET_DEVICE(0x1018),
69 INTEL_E1000_ETHERNET_DEVICE(0x1019),
70 INTEL_E1000_ETHERNET_DEVICE(0x101A),
71 INTEL_E1000_ETHERNET_DEVICE(0x101D),
72 INTEL_E1000_ETHERNET_DEVICE(0x101E),
73 INTEL_E1000_ETHERNET_DEVICE(0x1026),
74 INTEL_E1000_ETHERNET_DEVICE(0x1027),
75 INTEL_E1000_ETHERNET_DEVICE(0x1028),
76 INTEL_E1000_ETHERNET_DEVICE(0x1049),
77 INTEL_E1000_ETHERNET_DEVICE(0x104A),
78 INTEL_E1000_ETHERNET_DEVICE(0x104B),
79 INTEL_E1000_ETHERNET_DEVICE(0x104C),
80 INTEL_E1000_ETHERNET_DEVICE(0x104D),
81 INTEL_E1000_ETHERNET_DEVICE(0x105E),
82 INTEL_E1000_ETHERNET_DEVICE(0x105F),
83 INTEL_E1000_ETHERNET_DEVICE(0x1060),
84 INTEL_E1000_ETHERNET_DEVICE(0x1075),
85 INTEL_E1000_ETHERNET_DEVICE(0x1076),
86 INTEL_E1000_ETHERNET_DEVICE(0x1077),
87 INTEL_E1000_ETHERNET_DEVICE(0x1078),
88 INTEL_E1000_ETHERNET_DEVICE(0x1079),
89 INTEL_E1000_ETHERNET_DEVICE(0x107A),
90 INTEL_E1000_ETHERNET_DEVICE(0x107B),
91 INTEL_E1000_ETHERNET_DEVICE(0x107C),
92 INTEL_E1000_ETHERNET_DEVICE(0x107D),
93 INTEL_E1000_ETHERNET_DEVICE(0x107E),
94 INTEL_E1000_ETHERNET_DEVICE(0x107F),
95 INTEL_E1000_ETHERNET_DEVICE(0x108A),
96 INTEL_E1000_ETHERNET_DEVICE(0x108B),
97 INTEL_E1000_ETHERNET_DEVICE(0x108C),
98 INTEL_E1000_ETHERNET_DEVICE(0x1096),
99 INTEL_E1000_ETHERNET_DEVICE(0x1098),
100 INTEL_E1000_ETHERNET_DEVICE(0x1099),
101 INTEL_E1000_ETHERNET_DEVICE(0x109A),
102 INTEL_E1000_ETHERNET_DEVICE(0x10A4),
103 INTEL_E1000_ETHERNET_DEVICE(0x10B5),
104 INTEL_E1000_ETHERNET_DEVICE(0x10B9),
105 INTEL_E1000_ETHERNET_DEVICE(0x10BA),
106 INTEL_E1000_ETHERNET_DEVICE(0x10BB),
107 INTEL_E1000_ETHERNET_DEVICE(0x10BC),
108 INTEL_E1000_ETHERNET_DEVICE(0x10C4),
109 INTEL_E1000_ETHERNET_DEVICE(0x10C5),
110 /* required last entry */
114 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
116 int e1000_up(struct e1000_adapter *adapter);
117 void e1000_down(struct e1000_adapter *adapter);
118 void e1000_reinit_locked(struct e1000_adapter *adapter);
119 void e1000_reset(struct e1000_adapter *adapter);
120 int e1000_set_spd_dplx(struct e1000_adapter *adapter, uint16_t spddplx);
121 int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
122 int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
123 void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
124 void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
125 static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
126 struct e1000_tx_ring *txdr);
127 static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
128 struct e1000_rx_ring *rxdr);
129 static void e1000_free_tx_resources(struct e1000_adapter *adapter,
130 struct e1000_tx_ring *tx_ring);
131 static void e1000_free_rx_resources(struct e1000_adapter *adapter,
132 struct e1000_rx_ring *rx_ring);
133 void e1000_update_stats(struct e1000_adapter *adapter);
135 static int e1000_init_module(void);
136 static void e1000_exit_module(void);
137 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
138 static void __devexit e1000_remove(struct pci_dev *pdev);
139 static int e1000_alloc_queues(struct e1000_adapter *adapter);
140 static int e1000_sw_init(struct e1000_adapter *adapter);
141 static int e1000_open(struct net_device *netdev);
142 static int e1000_close(struct net_device *netdev);
143 static void e1000_configure_tx(struct e1000_adapter *adapter);
144 static void e1000_configure_rx(struct e1000_adapter *adapter);
145 static void e1000_setup_rctl(struct e1000_adapter *adapter);
146 static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter);
147 static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter);
148 static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
149 struct e1000_tx_ring *tx_ring);
150 static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
151 struct e1000_rx_ring *rx_ring);
152 static void e1000_set_multi(struct net_device *netdev);
153 static void e1000_update_phy_info(unsigned long data);
154 static void e1000_watchdog(unsigned long data);
155 static void e1000_82547_tx_fifo_stall(unsigned long data);
156 static int e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
157 static struct net_device_stats * e1000_get_stats(struct net_device *netdev);
158 static int e1000_change_mtu(struct net_device *netdev, int new_mtu);
159 static int e1000_set_mac(struct net_device *netdev, void *p);
160 static irqreturn_t e1000_intr(int irq, void *data);
161 #ifdef CONFIG_PCI_MSI
162 static irqreturn_t e1000_intr_msi(int irq, void *data);
164 static boolean_t e1000_clean_tx_irq(struct e1000_adapter *adapter,
165 struct e1000_tx_ring *tx_ring);
166 #ifdef CONFIG_E1000_NAPI
167 static int e1000_clean(struct net_device *poll_dev, int *budget);
168 static boolean_t e1000_clean_rx_irq(struct e1000_adapter *adapter,
169 struct e1000_rx_ring *rx_ring,
170 int *work_done, int work_to_do);
171 static boolean_t e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
172 struct e1000_rx_ring *rx_ring,
173 int *work_done, int work_to_do);
175 static boolean_t e1000_clean_rx_irq(struct e1000_adapter *adapter,
176 struct e1000_rx_ring *rx_ring);
177 static boolean_t e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
178 struct e1000_rx_ring *rx_ring);
180 static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
181 struct e1000_rx_ring *rx_ring,
183 static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
184 struct e1000_rx_ring *rx_ring,
186 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd);
187 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
189 void e1000_set_ethtool_ops(struct net_device *netdev);
190 static void e1000_enter_82542_rst(struct e1000_adapter *adapter);
191 static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
192 static void e1000_tx_timeout(struct net_device *dev);
193 static void e1000_reset_task(struct work_struct *work);
194 static void e1000_smartspeed(struct e1000_adapter *adapter);
195 static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
196 struct sk_buff *skb);
198 static void e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp);
199 static void e1000_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid);
200 static void e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
201 static void e1000_restore_vlan(struct e1000_adapter *adapter);
203 static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
205 static int e1000_resume(struct pci_dev *pdev);
207 static void e1000_shutdown(struct pci_dev *pdev);
209 #ifdef CONFIG_NET_POLL_CONTROLLER
210 /* for netdump / net console */
211 static void e1000_netpoll (struct net_device *netdev);
214 extern void e1000_check_options(struct e1000_adapter *adapter);
216 #define COPYBREAK_DEFAULT 256
217 static unsigned int copybreak __read_mostly = COPYBREAK_DEFAULT;
218 module_param(copybreak, uint, 0644);
219 MODULE_PARM_DESC(copybreak,
220 "Maximum size of packet that is copied to a new buffer on receive");
222 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
223 pci_channel_state_t state);
224 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev);
225 static void e1000_io_resume(struct pci_dev *pdev);
227 static struct pci_error_handlers e1000_err_handler = {
228 .error_detected = e1000_io_error_detected,
229 .slot_reset = e1000_io_slot_reset,
230 .resume = e1000_io_resume,
233 static struct pci_driver e1000_driver = {
234 .name = e1000_driver_name,
235 .id_table = e1000_pci_tbl,
236 .probe = e1000_probe,
237 .remove = __devexit_p(e1000_remove),
239 /* Power Managment Hooks */
240 .suspend = e1000_suspend,
241 .resume = e1000_resume,
243 .shutdown = e1000_shutdown,
244 .err_handler = &e1000_err_handler
247 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
248 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
249 MODULE_LICENSE("GPL");
250 MODULE_VERSION(DRV_VERSION);
252 static int debug = NETIF_MSG_DRV | NETIF_MSG_PROBE;
253 module_param(debug, int, 0);
254 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
257 * e1000_init_module - Driver Registration Routine
259 * e1000_init_module is the first routine called when the driver is
260 * loaded. All it does is register with the PCI subsystem.
264 e1000_init_module(void)
267 printk(KERN_INFO "%s - version %s\n",
268 e1000_driver_string, e1000_driver_version);
270 printk(KERN_INFO "%s\n", e1000_copyright);
272 ret = pci_register_driver(&e1000_driver);
273 if (copybreak != COPYBREAK_DEFAULT) {
275 printk(KERN_INFO "e1000: copybreak disabled\n");
277 printk(KERN_INFO "e1000: copybreak enabled for "
278 "packets <= %u bytes\n", copybreak);
283 module_init(e1000_init_module);
286 * e1000_exit_module - Driver Exit Cleanup Routine
288 * e1000_exit_module is called just before the driver is removed
293 e1000_exit_module(void)
295 pci_unregister_driver(&e1000_driver);
298 module_exit(e1000_exit_module);
300 static int e1000_request_irq(struct e1000_adapter *adapter)
302 struct net_device *netdev = adapter->netdev;
306 #ifdef CONFIG_PCI_MSI
307 if (adapter->hw.mac_type >= e1000_82571) {
308 adapter->have_msi = TRUE;
309 if ((err = pci_enable_msi(adapter->pdev))) {
311 "Unable to allocate MSI interrupt Error: %d\n", err);
312 adapter->have_msi = FALSE;
315 if (adapter->have_msi) {
316 flags &= ~IRQF_SHARED;
317 err = request_irq(adapter->pdev->irq, &e1000_intr_msi, flags,
318 netdev->name, netdev);
321 "Unable to allocate interrupt Error: %d\n", err);
324 if ((err = request_irq(adapter->pdev->irq, &e1000_intr, flags,
325 netdev->name, netdev)))
327 "Unable to allocate interrupt Error: %d\n", err);
332 static void e1000_free_irq(struct e1000_adapter *adapter)
334 struct net_device *netdev = adapter->netdev;
336 free_irq(adapter->pdev->irq, netdev);
338 #ifdef CONFIG_PCI_MSI
339 if (adapter->have_msi)
340 pci_disable_msi(adapter->pdev);
345 * e1000_irq_disable - Mask off interrupt generation on the NIC
346 * @adapter: board private structure
350 e1000_irq_disable(struct e1000_adapter *adapter)
352 atomic_inc(&adapter->irq_sem);
353 E1000_WRITE_REG(&adapter->hw, IMC, ~0);
354 E1000_WRITE_FLUSH(&adapter->hw);
355 synchronize_irq(adapter->pdev->irq);
359 * e1000_irq_enable - Enable default interrupt generation settings
360 * @adapter: board private structure
364 e1000_irq_enable(struct e1000_adapter *adapter)
366 if (likely(atomic_dec_and_test(&adapter->irq_sem))) {
367 E1000_WRITE_REG(&adapter->hw, IMS, IMS_ENABLE_MASK);
368 E1000_WRITE_FLUSH(&adapter->hw);
373 e1000_update_mng_vlan(struct e1000_adapter *adapter)
375 struct net_device *netdev = adapter->netdev;
376 uint16_t vid = adapter->hw.mng_cookie.vlan_id;
377 uint16_t old_vid = adapter->mng_vlan_id;
378 if (adapter->vlgrp) {
379 if (!vlan_group_get_device(adapter->vlgrp, vid)) {
380 if (adapter->hw.mng_cookie.status &
381 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) {
382 e1000_vlan_rx_add_vid(netdev, vid);
383 adapter->mng_vlan_id = vid;
385 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
387 if ((old_vid != (uint16_t)E1000_MNG_VLAN_NONE) &&
389 !vlan_group_get_device(adapter->vlgrp, old_vid))
390 e1000_vlan_rx_kill_vid(netdev, old_vid);
392 adapter->mng_vlan_id = vid;
397 * e1000_release_hw_control - release control of the h/w to f/w
398 * @adapter: address of board private structure
400 * e1000_release_hw_control resets {CTRL_EXT|FWSM}:DRV_LOAD bit.
401 * For ASF and Pass Through versions of f/w this means that the
402 * driver is no longer loaded. For AMT version (only with 82573) i
403 * of the f/w this means that the network i/f is closed.
408 e1000_release_hw_control(struct e1000_adapter *adapter)
414 /* Let firmware taken over control of h/w */
415 switch (adapter->hw.mac_type) {
418 case e1000_80003es2lan:
419 ctrl_ext = E1000_READ_REG(&adapter->hw, CTRL_EXT);
420 E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
421 ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
424 swsm = E1000_READ_REG(&adapter->hw, SWSM);
425 E1000_WRITE_REG(&adapter->hw, SWSM,
426 swsm & ~E1000_SWSM_DRV_LOAD);
428 extcnf = E1000_READ_REG(&adapter->hw, CTRL_EXT);
429 E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
430 extcnf & ~E1000_CTRL_EXT_DRV_LOAD);
438 * e1000_get_hw_control - get control of the h/w from f/w
439 * @adapter: address of board private structure
441 * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
442 * For ASF and Pass Through versions of f/w this means that
443 * the driver is loaded. For AMT version (only with 82573)
444 * of the f/w this means that the network i/f is open.
449 e1000_get_hw_control(struct e1000_adapter *adapter)
455 /* Let firmware know the driver has taken over */
456 switch (adapter->hw.mac_type) {
459 case e1000_80003es2lan:
460 ctrl_ext = E1000_READ_REG(&adapter->hw, CTRL_EXT);
461 E1000_WRITE_REG(&adapter->hw, CTRL_EXT,
462 ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
465 swsm = E1000_READ_REG(&adapter->hw, SWSM);
466 E1000_WRITE_REG(&adapter->hw, SWSM,
467 swsm | E1000_SWSM_DRV_LOAD);
470 extcnf = E1000_READ_REG(&adapter->hw, EXTCNF_CTRL);
471 E1000_WRITE_REG(&adapter->hw, EXTCNF_CTRL,
472 extcnf | E1000_EXTCNF_CTRL_SWFLAG);
480 e1000_init_manageability(struct e1000_adapter *adapter)
482 if (adapter->en_mng_pt) {
483 uint32_t manc = E1000_READ_REG(&adapter->hw, MANC);
485 /* disable hardware interception of ARP */
486 manc &= ~(E1000_MANC_ARP_EN);
488 /* enable receiving management packets to the host */
489 /* this will probably generate destination unreachable messages
490 * from the host OS, but the packets will be handled on SMBUS */
491 if (adapter->hw.has_manc2h) {
492 uint32_t manc2h = E1000_READ_REG(&adapter->hw, MANC2H);
494 manc |= E1000_MANC_EN_MNG2HOST;
495 #define E1000_MNG2HOST_PORT_623 (1 << 5)
496 #define E1000_MNG2HOST_PORT_664 (1 << 6)
497 manc2h |= E1000_MNG2HOST_PORT_623;
498 manc2h |= E1000_MNG2HOST_PORT_664;
499 E1000_WRITE_REG(&adapter->hw, MANC2H, manc2h);
502 E1000_WRITE_REG(&adapter->hw, MANC, manc);
507 e1000_release_manageability(struct e1000_adapter *adapter)
509 if (adapter->en_mng_pt) {
510 uint32_t manc = E1000_READ_REG(&adapter->hw, MANC);
512 /* re-enable hardware interception of ARP */
513 manc |= E1000_MANC_ARP_EN;
515 if (adapter->hw.has_manc2h)
516 manc &= ~E1000_MANC_EN_MNG2HOST;
518 /* don't explicitly have to mess with MANC2H since
519 * MANC has an enable disable that gates MANC2H */
521 E1000_WRITE_REG(&adapter->hw, MANC, manc);
526 e1000_up(struct e1000_adapter *adapter)
528 struct net_device *netdev = adapter->netdev;
531 /* hardware has been reset, we need to reload some things */
533 e1000_set_multi(netdev);
535 e1000_restore_vlan(adapter);
536 e1000_init_manageability(adapter);
538 e1000_configure_tx(adapter);
539 e1000_setup_rctl(adapter);
540 e1000_configure_rx(adapter);
541 /* call E1000_DESC_UNUSED which always leaves
542 * at least 1 descriptor unused to make sure
543 * next_to_use != next_to_clean */
544 for (i = 0; i < adapter->num_rx_queues; i++) {
545 struct e1000_rx_ring *ring = &adapter->rx_ring[i];
546 adapter->alloc_rx_buf(adapter, ring,
547 E1000_DESC_UNUSED(ring));
550 adapter->tx_queue_len = netdev->tx_queue_len;
552 #ifdef CONFIG_E1000_NAPI
553 netif_poll_enable(netdev);
555 e1000_irq_enable(adapter);
557 clear_bit(__E1000_DOWN, &adapter->flags);
559 /* fire a link change interrupt to start the watchdog */
560 E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_LSC);
565 * e1000_power_up_phy - restore link in case the phy was powered down
566 * @adapter: address of board private structure
568 * The phy may be powered down to save power and turn off link when the
569 * driver is unloaded and wake on lan is not enabled (among others)
570 * *** this routine MUST be followed by a call to e1000_reset ***
574 void e1000_power_up_phy(struct e1000_adapter *adapter)
576 uint16_t mii_reg = 0;
578 /* Just clear the power down bit to wake the phy back up */
579 if (adapter->hw.media_type == e1000_media_type_copper) {
580 /* according to the manual, the phy will retain its
581 * settings across a power-down/up cycle */
582 e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
583 mii_reg &= ~MII_CR_POWER_DOWN;
584 e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
588 static void e1000_power_down_phy(struct e1000_adapter *adapter)
590 /* Power down the PHY so no link is implied when interface is down *
591 * The PHY cannot be powered down if any of the following is TRUE *
594 * (c) SoL/IDER session is active */
595 if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
596 adapter->hw.media_type == e1000_media_type_copper) {
597 uint16_t mii_reg = 0;
599 switch (adapter->hw.mac_type) {
602 case e1000_82545_rev_3:
604 case e1000_82546_rev_3:
606 case e1000_82541_rev_2:
608 case e1000_82547_rev_2:
609 if (E1000_READ_REG(&adapter->hw, MANC) &
616 case e1000_80003es2lan:
618 if (e1000_check_mng_mode(&adapter->hw) ||
619 e1000_check_phy_reset_block(&adapter->hw))
625 e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
626 mii_reg |= MII_CR_POWER_DOWN;
627 e1000_write_phy_reg(&adapter->hw, PHY_CTRL, mii_reg);
635 e1000_down(struct e1000_adapter *adapter)
637 struct net_device *netdev = adapter->netdev;
639 /* signal that we're down so the interrupt handler does not
640 * reschedule our watchdog timer */
641 set_bit(__E1000_DOWN, &adapter->flags);
643 e1000_irq_disable(adapter);
645 del_timer_sync(&adapter->tx_fifo_stall_timer);
646 del_timer_sync(&adapter->watchdog_timer);
647 del_timer_sync(&adapter->phy_info_timer);
649 #ifdef CONFIG_E1000_NAPI
650 netif_poll_disable(netdev);
652 netdev->tx_queue_len = adapter->tx_queue_len;
653 adapter->link_speed = 0;
654 adapter->link_duplex = 0;
655 netif_carrier_off(netdev);
656 netif_stop_queue(netdev);
658 e1000_reset(adapter);
659 e1000_clean_all_tx_rings(adapter);
660 e1000_clean_all_rx_rings(adapter);
664 e1000_reinit_locked(struct e1000_adapter *adapter)
666 WARN_ON(in_interrupt());
667 while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
671 clear_bit(__E1000_RESETTING, &adapter->flags);
675 e1000_reset(struct e1000_adapter *adapter)
677 uint32_t pba = 0, tx_space, min_tx_space, min_rx_space;
678 uint16_t fc_high_water_mark = E1000_FC_HIGH_DIFF;
679 boolean_t legacy_pba_adjust = FALSE;
681 /* Repartition Pba for greater than 9k mtu
682 * To take effect CTRL.RST is required.
685 switch (adapter->hw.mac_type) {
686 case e1000_82542_rev2_0:
687 case e1000_82542_rev2_1:
692 case e1000_82541_rev_2:
693 legacy_pba_adjust = TRUE;
697 case e1000_82545_rev_3:
699 case e1000_82546_rev_3:
703 case e1000_82547_rev_2:
704 legacy_pba_adjust = TRUE;
709 case e1000_80003es2lan:
717 case e1000_undefined:
722 if (legacy_pba_adjust == TRUE) {
723 if (adapter->netdev->mtu > E1000_RXBUFFER_8192)
724 pba -= 8; /* allocate more FIFO for Tx */
726 if (adapter->hw.mac_type == e1000_82547) {
727 adapter->tx_fifo_head = 0;
728 adapter->tx_head_addr = pba << E1000_TX_HEAD_ADDR_SHIFT;
729 adapter->tx_fifo_size =
730 (E1000_PBA_40K - pba) << E1000_PBA_BYTES_SHIFT;
731 atomic_set(&adapter->tx_fifo_stall, 0);
733 } else if (adapter->hw.max_frame_size > MAXIMUM_ETHERNET_FRAME_SIZE) {
734 /* adjust PBA for jumbo frames */
735 E1000_WRITE_REG(&adapter->hw, PBA, pba);
737 /* To maintain wire speed transmits, the Tx FIFO should be
738 * large enough to accomodate two full transmit packets,
739 * rounded up to the next 1KB and expressed in KB. Likewise,
740 * the Rx FIFO should be large enough to accomodate at least
741 * one full receive packet and is similarly rounded up and
742 * expressed in KB. */
743 pba = E1000_READ_REG(&adapter->hw, PBA);
744 /* upper 16 bits has Tx packet buffer allocation size in KB */
745 tx_space = pba >> 16;
746 /* lower 16 bits has Rx packet buffer allocation size in KB */
748 /* don't include ethernet FCS because hardware appends/strips */
749 min_rx_space = adapter->netdev->mtu + ENET_HEADER_SIZE +
751 min_tx_space = min_rx_space;
753 E1000_ROUNDUP(min_tx_space, 1024);
755 E1000_ROUNDUP(min_rx_space, 1024);
758 /* If current Tx allocation is less than the min Tx FIFO size,
759 * and the min Tx FIFO size is less than the current Rx FIFO
760 * allocation, take space away from current Rx allocation */
761 if (tx_space < min_tx_space &&
762 ((min_tx_space - tx_space) < pba)) {
763 pba = pba - (min_tx_space - tx_space);
765 /* PCI/PCIx hardware has PBA alignment constraints */
766 switch (adapter->hw.mac_type) {
767 case e1000_82545 ... e1000_82546_rev_3:
768 pba &= ~(E1000_PBA_8K - 1);
774 /* if short on rx space, rx wins and must trump tx
775 * adjustment or use Early Receive if available */
776 if (pba < min_rx_space) {
777 switch (adapter->hw.mac_type) {
779 /* ERT enabled in e1000_configure_rx */
789 E1000_WRITE_REG(&adapter->hw, PBA, pba);
791 /* flow control settings */
792 /* Set the FC high water mark to 90% of the FIFO size.
793 * Required to clear last 3 LSB */
794 fc_high_water_mark = ((pba * 9216)/10) & 0xFFF8;
795 /* We can't use 90% on small FIFOs because the remainder
796 * would be less than 1 full frame. In this case, we size
797 * it to allow at least a full frame above the high water
799 if (pba < E1000_PBA_16K)
800 fc_high_water_mark = (pba * 1024) - 1600;
802 adapter->hw.fc_high_water = fc_high_water_mark;
803 adapter->hw.fc_low_water = fc_high_water_mark - 8;
804 if (adapter->hw.mac_type == e1000_80003es2lan)
805 adapter->hw.fc_pause_time = 0xFFFF;
807 adapter->hw.fc_pause_time = E1000_FC_PAUSE_TIME;
808 adapter->hw.fc_send_xon = 1;
809 adapter->hw.fc = adapter->hw.original_fc;
811 /* Allow time for pending master requests to run */
812 e1000_reset_hw(&adapter->hw);
813 if (adapter->hw.mac_type >= e1000_82544)
814 E1000_WRITE_REG(&adapter->hw, WUC, 0);
816 if (e1000_init_hw(&adapter->hw))
817 DPRINTK(PROBE, ERR, "Hardware Error\n");
818 e1000_update_mng_vlan(adapter);
820 /* if (adapter->hwflags & HWFLAGS_PHY_PWR_BIT) { */
821 if (adapter->hw.mac_type >= e1000_82544 &&
822 adapter->hw.mac_type <= e1000_82547_rev_2 &&
823 adapter->hw.autoneg == 1 &&
824 adapter->hw.autoneg_advertised == ADVERTISE_1000_FULL) {
825 uint32_t ctrl = E1000_READ_REG(&adapter->hw, CTRL);
826 /* clear phy power management bit if we are in gig only mode,
827 * which if enabled will attempt negotiation to 100Mb, which
828 * can cause a loss of link at power off or driver unload */
829 ctrl &= ~E1000_CTRL_SWDPIN3;
830 E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
833 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
834 E1000_WRITE_REG(&adapter->hw, VET, ETHERNET_IEEE_VLAN_TYPE);
836 e1000_reset_adaptive(&adapter->hw);
837 e1000_phy_get_info(&adapter->hw, &adapter->phy_info);
839 if (!adapter->smart_power_down &&
840 (adapter->hw.mac_type == e1000_82571 ||
841 adapter->hw.mac_type == e1000_82572)) {
842 uint16_t phy_data = 0;
843 /* speed up time to link by disabling smart power down, ignore
844 * the return value of this function because there is nothing
845 * different we would do if it failed */
846 e1000_read_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT,
848 phy_data &= ~IGP02E1000_PM_SPD;
849 e1000_write_phy_reg(&adapter->hw, IGP02E1000_PHY_POWER_MGMT,
853 e1000_release_manageability(adapter);
857 * e1000_probe - Device Initialization Routine
858 * @pdev: PCI device information struct
859 * @ent: entry in e1000_pci_tbl
861 * Returns 0 on success, negative on failure
863 * e1000_probe initializes an adapter identified by a pci_dev structure.
864 * The OS initialization, configuring of the adapter private structure,
865 * and a hardware reset occur.
869 e1000_probe(struct pci_dev *pdev,
870 const struct pci_device_id *ent)
872 struct net_device *netdev;
873 struct e1000_adapter *adapter;
874 unsigned long mmio_start, mmio_len;
875 unsigned long flash_start, flash_len;
877 static int cards_found = 0;
878 static int global_quad_port_a = 0; /* global ksp3 port a indication */
879 int i, err, pci_using_dac;
880 uint16_t eeprom_data = 0;
881 uint16_t eeprom_apme_mask = E1000_EEPROM_APME;
882 if ((err = pci_enable_device(pdev)))
885 if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)) &&
886 !(err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK))) {
889 if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) &&
890 (err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) {
891 E1000_ERR("No usable DMA configuration, aborting\n");
897 if ((err = pci_request_regions(pdev, e1000_driver_name)))
900 pci_set_master(pdev);
903 netdev = alloc_etherdev(sizeof(struct e1000_adapter));
905 goto err_alloc_etherdev;
907 SET_MODULE_OWNER(netdev);
908 SET_NETDEV_DEV(netdev, &pdev->dev);
910 pci_set_drvdata(pdev, netdev);
911 adapter = netdev_priv(netdev);
912 adapter->netdev = netdev;
913 adapter->pdev = pdev;
914 adapter->hw.back = adapter;
915 adapter->msg_enable = (1 << debug) - 1;
917 mmio_start = pci_resource_start(pdev, BAR_0);
918 mmio_len = pci_resource_len(pdev, BAR_0);
921 adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
922 if (!adapter->hw.hw_addr)
925 for (i = BAR_1; i <= BAR_5; i++) {
926 if (pci_resource_len(pdev, i) == 0)
928 if (pci_resource_flags(pdev, i) & IORESOURCE_IO) {
929 adapter->hw.io_base = pci_resource_start(pdev, i);
934 netdev->open = &e1000_open;
935 netdev->stop = &e1000_close;
936 netdev->hard_start_xmit = &e1000_xmit_frame;
937 netdev->get_stats = &e1000_get_stats;
938 netdev->set_multicast_list = &e1000_set_multi;
939 netdev->set_mac_address = &e1000_set_mac;
940 netdev->change_mtu = &e1000_change_mtu;
941 netdev->do_ioctl = &e1000_ioctl;
942 e1000_set_ethtool_ops(netdev);
943 netdev->tx_timeout = &e1000_tx_timeout;
944 netdev->watchdog_timeo = 5 * HZ;
945 #ifdef CONFIG_E1000_NAPI
946 netdev->poll = &e1000_clean;
949 netdev->vlan_rx_register = e1000_vlan_rx_register;
950 netdev->vlan_rx_add_vid = e1000_vlan_rx_add_vid;
951 netdev->vlan_rx_kill_vid = e1000_vlan_rx_kill_vid;
952 #ifdef CONFIG_NET_POLL_CONTROLLER
953 netdev->poll_controller = e1000_netpoll;
955 strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
957 netdev->mem_start = mmio_start;
958 netdev->mem_end = mmio_start + mmio_len;
959 netdev->base_addr = adapter->hw.io_base;
961 adapter->bd_number = cards_found;
963 /* setup the private structure */
965 if ((err = e1000_sw_init(adapter)))
969 /* Flash BAR mapping must happen after e1000_sw_init
970 * because it depends on mac_type */
971 if ((adapter->hw.mac_type == e1000_ich8lan) &&
972 (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
973 flash_start = pci_resource_start(pdev, 1);
974 flash_len = pci_resource_len(pdev, 1);
975 adapter->hw.flash_address = ioremap(flash_start, flash_len);
976 if (!adapter->hw.flash_address)
980 if (e1000_check_phy_reset_block(&adapter->hw))
981 DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
983 if (adapter->hw.mac_type >= e1000_82543) {
984 netdev->features = NETIF_F_SG |
988 NETIF_F_HW_VLAN_FILTER;
989 if (adapter->hw.mac_type == e1000_ich8lan)
990 netdev->features &= ~NETIF_F_HW_VLAN_FILTER;
993 if ((adapter->hw.mac_type >= e1000_82544) &&
994 (adapter->hw.mac_type != e1000_82547))
995 netdev->features |= NETIF_F_TSO;
997 if (adapter->hw.mac_type > e1000_82547_rev_2)
998 netdev->features |= NETIF_F_TSO6;
1000 netdev->features |= NETIF_F_HIGHDMA;
1002 netdev->features |= NETIF_F_LLTX;
1004 adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw);
1006 /* initialize eeprom parameters */
1008 if (e1000_init_eeprom_params(&adapter->hw)) {
1009 E1000_ERR("EEPROM initialization failed\n");
1013 /* before reading the EEPROM, reset the controller to
1014 * put the device in a known good starting state */
1016 e1000_reset_hw(&adapter->hw);
1018 /* make sure the EEPROM is good */
1020 if (e1000_validate_eeprom_checksum(&adapter->hw) < 0) {
1021 DPRINTK(PROBE, ERR, "The EEPROM Checksum Is Not Valid\n");
1025 /* copy the MAC address out of the EEPROM */
1027 if (e1000_read_mac_addr(&adapter->hw))
1028 DPRINTK(PROBE, ERR, "EEPROM Read Error\n");
1029 memcpy(netdev->dev_addr, adapter->hw.mac_addr, netdev->addr_len);
1030 memcpy(netdev->perm_addr, adapter->hw.mac_addr, netdev->addr_len);
1032 if (!is_valid_ether_addr(netdev->perm_addr)) {
1033 DPRINTK(PROBE, ERR, "Invalid MAC Address\n");
1037 e1000_get_bus_info(&adapter->hw);
1039 init_timer(&adapter->tx_fifo_stall_timer);
1040 adapter->tx_fifo_stall_timer.function = &e1000_82547_tx_fifo_stall;
1041 adapter->tx_fifo_stall_timer.data = (unsigned long) adapter;
1043 init_timer(&adapter->watchdog_timer);
1044 adapter->watchdog_timer.function = &e1000_watchdog;
1045 adapter->watchdog_timer.data = (unsigned long) adapter;
1047 init_timer(&adapter->phy_info_timer);
1048 adapter->phy_info_timer.function = &e1000_update_phy_info;
1049 adapter->phy_info_timer.data = (unsigned long) adapter;
1051 INIT_WORK(&adapter->reset_task, e1000_reset_task);
1053 e1000_check_options(adapter);
1055 /* Initial Wake on LAN setting
1056 * If APM wake is enabled in the EEPROM,
1057 * enable the ACPI Magic Packet filter
1060 switch (adapter->hw.mac_type) {
1061 case e1000_82542_rev2_0:
1062 case e1000_82542_rev2_1:
1066 e1000_read_eeprom(&adapter->hw,
1067 EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
1068 eeprom_apme_mask = E1000_EEPROM_82544_APM;
1071 e1000_read_eeprom(&adapter->hw,
1072 EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data);
1073 eeprom_apme_mask = E1000_EEPROM_ICH8_APME;
1076 case e1000_82546_rev_3:
1078 case e1000_80003es2lan:
1079 if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1){
1080 e1000_read_eeprom(&adapter->hw,
1081 EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
1086 e1000_read_eeprom(&adapter->hw,
1087 EEPROM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
1090 if (eeprom_data & eeprom_apme_mask)
1091 adapter->eeprom_wol |= E1000_WUFC_MAG;
1093 /* now that we have the eeprom settings, apply the special cases
1094 * where the eeprom may be wrong or the board simply won't support
1095 * wake on lan on a particular port */
1096 switch (pdev->device) {
1097 case E1000_DEV_ID_82546GB_PCIE:
1098 adapter->eeprom_wol = 0;
1100 case E1000_DEV_ID_82546EB_FIBER:
1101 case E1000_DEV_ID_82546GB_FIBER:
1102 case E1000_DEV_ID_82571EB_FIBER:
1103 /* Wake events only supported on port A for dual fiber
1104 * regardless of eeprom setting */
1105 if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1)
1106 adapter->eeprom_wol = 0;
1108 case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
1109 case E1000_DEV_ID_82571EB_QUAD_COPPER:
1110 case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
1111 /* if quad port adapter, disable WoL on all but port A */
1112 if (global_quad_port_a != 0)
1113 adapter->eeprom_wol = 0;
1115 adapter->quad_port_a = 1;
1116 /* Reset for multiple quad port adapters */
1117 if (++global_quad_port_a == 4)
1118 global_quad_port_a = 0;
1122 /* initialize the wol settings based on the eeprom settings */
1123 adapter->wol = adapter->eeprom_wol;
1125 /* print bus type/speed/width info */
1127 struct e1000_hw *hw = &adapter->hw;
1128 DPRINTK(PROBE, INFO, "(PCI%s:%s:%s) ",
1129 ((hw->bus_type == e1000_bus_type_pcix) ? "-X" :
1130 (hw->bus_type == e1000_bus_type_pci_express ? " Express":"")),
1131 ((hw->bus_speed == e1000_bus_speed_2500) ? "2.5Gb/s" :
1132 (hw->bus_speed == e1000_bus_speed_133) ? "133MHz" :
1133 (hw->bus_speed == e1000_bus_speed_120) ? "120MHz" :
1134 (hw->bus_speed == e1000_bus_speed_100) ? "100MHz" :
1135 (hw->bus_speed == e1000_bus_speed_66) ? "66MHz" : "33MHz"),
1136 ((hw->bus_width == e1000_bus_width_64) ? "64-bit" :
1137 (hw->bus_width == e1000_bus_width_pciex_4) ? "Width x4" :
1138 (hw->bus_width == e1000_bus_width_pciex_1) ? "Width x1" :
1142 for (i = 0; i < 6; i++)
1143 printk("%2.2x%c", netdev->dev_addr[i], i == 5 ? '\n' : ':');
1145 /* reset the hardware with the new settings */
1146 e1000_reset(adapter);
1148 /* If the controller is 82573 and f/w is AMT, do not set
1149 * DRV_LOAD until the interface is up. For all other cases,
1150 * let the f/w know that the h/w is now under the control
1152 if (adapter->hw.mac_type != e1000_82573 ||
1153 !e1000_check_mng_mode(&adapter->hw))
1154 e1000_get_hw_control(adapter);
1156 strcpy(netdev->name, "eth%d");
1157 if ((err = register_netdev(netdev)))
1160 /* tell the stack to leave us alone until e1000_open() is called */
1161 netif_carrier_off(netdev);
1162 netif_stop_queue(netdev);
1164 DPRINTK(PROBE, INFO, "Intel(R) PRO/1000 Network Connection\n");
1170 e1000_release_hw_control(adapter);
1172 if (!e1000_check_phy_reset_block(&adapter->hw))
1173 e1000_phy_hw_reset(&adapter->hw);
1175 if (adapter->hw.flash_address)
1176 iounmap(adapter->hw.flash_address);
1178 #ifdef CONFIG_E1000_NAPI
1179 for (i = 0; i < adapter->num_rx_queues; i++)
1180 dev_put(&adapter->polling_netdev[i]);
1183 kfree(adapter->tx_ring);
1184 kfree(adapter->rx_ring);
1185 #ifdef CONFIG_E1000_NAPI
1186 kfree(adapter->polling_netdev);
1189 iounmap(adapter->hw.hw_addr);
1191 free_netdev(netdev);
1193 pci_release_regions(pdev);
1196 pci_disable_device(pdev);
1201 * e1000_remove - Device Removal Routine
1202 * @pdev: PCI device information struct
1204 * e1000_remove is called by the PCI subsystem to alert the driver
1205 * that it should release a PCI device. The could be caused by a
1206 * Hot-Plug event, or because the driver is going to be removed from
1210 static void __devexit
1211 e1000_remove(struct pci_dev *pdev)
1213 struct net_device *netdev = pci_get_drvdata(pdev);
1214 struct e1000_adapter *adapter = netdev_priv(netdev);
1215 #ifdef CONFIG_E1000_NAPI
1219 flush_scheduled_work();
1221 e1000_release_manageability(adapter);
1223 /* Release control of h/w to f/w. If f/w is AMT enabled, this
1224 * would have already happened in close and is redundant. */
1225 e1000_release_hw_control(adapter);
1227 unregister_netdev(netdev);
1228 #ifdef CONFIG_E1000_NAPI
1229 for (i = 0; i < adapter->num_rx_queues; i++)
1230 dev_put(&adapter->polling_netdev[i]);
1233 if (!e1000_check_phy_reset_block(&adapter->hw))
1234 e1000_phy_hw_reset(&adapter->hw);
1236 kfree(adapter->tx_ring);
1237 kfree(adapter->rx_ring);
1238 #ifdef CONFIG_E1000_NAPI
1239 kfree(adapter->polling_netdev);
1242 iounmap(adapter->hw.hw_addr);
1243 if (adapter->hw.flash_address)
1244 iounmap(adapter->hw.flash_address);
1245 pci_release_regions(pdev);
1247 free_netdev(netdev);
1249 pci_disable_device(pdev);
1253 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
1254 * @adapter: board private structure to initialize
1256 * e1000_sw_init initializes the Adapter private data structure.
1257 * Fields are initialized based on PCI device information and
1258 * OS network device settings (MTU size).
1261 static int __devinit
1262 e1000_sw_init(struct e1000_adapter *adapter)
1264 struct e1000_hw *hw = &adapter->hw;
1265 struct net_device *netdev = adapter->netdev;
1266 struct pci_dev *pdev = adapter->pdev;
1267 #ifdef CONFIG_E1000_NAPI
1271 /* PCI config space info */
1273 hw->vendor_id = pdev->vendor;
1274 hw->device_id = pdev->device;
1275 hw->subsystem_vendor_id = pdev->subsystem_vendor;
1276 hw->subsystem_id = pdev->subsystem_device;
1278 pci_read_config_byte(pdev, PCI_REVISION_ID, &hw->revision_id);
1280 pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
1282 adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
1283 adapter->rx_ps_bsize0 = E1000_RXBUFFER_128;
1284 hw->max_frame_size = netdev->mtu +
1285 ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
1286 hw->min_frame_size = MINIMUM_ETHERNET_FRAME_SIZE;
1288 /* identify the MAC */
1290 if (e1000_set_mac_type(hw)) {
1291 DPRINTK(PROBE, ERR, "Unknown MAC Type\n");
1295 switch (hw->mac_type) {
1300 case e1000_82541_rev_2:
1301 case e1000_82547_rev_2:
1302 hw->phy_init_script = 1;
1306 e1000_set_media_type(hw);
1308 hw->wait_autoneg_complete = FALSE;
1309 hw->tbi_compatibility_en = TRUE;
1310 hw->adaptive_ifs = TRUE;
1312 /* Copper options */
1314 if (hw->media_type == e1000_media_type_copper) {
1315 hw->mdix = AUTO_ALL_MODES;
1316 hw->disable_polarity_correction = FALSE;
1317 hw->master_slave = E1000_MASTER_SLAVE;
1320 adapter->num_tx_queues = 1;
1321 adapter->num_rx_queues = 1;
1323 if (e1000_alloc_queues(adapter)) {
1324 DPRINTK(PROBE, ERR, "Unable to allocate memory for queues\n");
1328 #ifdef CONFIG_E1000_NAPI
1329 for (i = 0; i < adapter->num_rx_queues; i++) {
1330 adapter->polling_netdev[i].priv = adapter;
1331 adapter->polling_netdev[i].poll = &e1000_clean;
1332 adapter->polling_netdev[i].weight = 64;
1333 dev_hold(&adapter->polling_netdev[i]);
1334 set_bit(__LINK_STATE_START, &adapter->polling_netdev[i].state);
1336 spin_lock_init(&adapter->tx_queue_lock);
1339 atomic_set(&adapter->irq_sem, 1);
1340 spin_lock_init(&adapter->stats_lock);
1342 set_bit(__E1000_DOWN, &adapter->flags);
1348 * e1000_alloc_queues - Allocate memory for all rings
1349 * @adapter: board private structure to initialize
1351 * We allocate one ring per queue at run-time since we don't know the
1352 * number of queues at compile-time. The polling_netdev array is
1353 * intended for Multiqueue, but should work fine with a single queue.
1356 static int __devinit
1357 e1000_alloc_queues(struct e1000_adapter *adapter)
1361 size = sizeof(struct e1000_tx_ring) * adapter->num_tx_queues;
1362 adapter->tx_ring = kmalloc(size, GFP_KERNEL);
1363 if (!adapter->tx_ring)
1365 memset(adapter->tx_ring, 0, size);
1367 size = sizeof(struct e1000_rx_ring) * adapter->num_rx_queues;
1368 adapter->rx_ring = kmalloc(size, GFP_KERNEL);
1369 if (!adapter->rx_ring) {
1370 kfree(adapter->tx_ring);
1373 memset(adapter->rx_ring, 0, size);
1375 #ifdef CONFIG_E1000_NAPI
1376 size = sizeof(struct net_device) * adapter->num_rx_queues;
1377 adapter->polling_netdev = kmalloc(size, GFP_KERNEL);
1378 if (!adapter->polling_netdev) {
1379 kfree(adapter->tx_ring);
1380 kfree(adapter->rx_ring);
1383 memset(adapter->polling_netdev, 0, size);
1386 return E1000_SUCCESS;
1390 * e1000_open - Called when a network interface is made active
1391 * @netdev: network interface device structure
1393 * Returns 0 on success, negative value on failure
1395 * The open entry point is called when a network interface is made
1396 * active by the system (IFF_UP). At this point all resources needed
1397 * for transmit and receive operations are allocated, the interrupt
1398 * handler is registered with the OS, the watchdog timer is started,
1399 * and the stack is notified that the interface is ready.
1403 e1000_open(struct net_device *netdev)
1405 struct e1000_adapter *adapter = netdev_priv(netdev);
1408 /* disallow open during test */
1409 if (test_bit(__E1000_TESTING, &adapter->flags))
1412 /* allocate transmit descriptors */
1413 if ((err = e1000_setup_all_tx_resources(adapter)))
1416 /* allocate receive descriptors */
1417 if ((err = e1000_setup_all_rx_resources(adapter)))
1420 err = e1000_request_irq(adapter);
1424 e1000_power_up_phy(adapter);
1426 if ((err = e1000_up(adapter)))
1428 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
1429 if ((adapter->hw.mng_cookie.status &
1430 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) {
1431 e1000_update_mng_vlan(adapter);
1434 /* If AMT is enabled, let the firmware know that the network
1435 * interface is now open */
1436 if (adapter->hw.mac_type == e1000_82573 &&
1437 e1000_check_mng_mode(&adapter->hw))
1438 e1000_get_hw_control(adapter);
1440 return E1000_SUCCESS;
1443 e1000_power_down_phy(adapter);
1444 e1000_free_irq(adapter);
1446 e1000_free_all_rx_resources(adapter);
1448 e1000_free_all_tx_resources(adapter);
1450 e1000_reset(adapter);
1456 * e1000_close - Disables a network interface
1457 * @netdev: network interface device structure
1459 * Returns 0, this is not allowed to fail
1461 * The close entry point is called when an interface is de-activated
1462 * by the OS. The hardware is still under the drivers control, but
1463 * needs to be disabled. A global MAC reset is issued to stop the
1464 * hardware, and all transmit and receive resources are freed.
1468 e1000_close(struct net_device *netdev)
1470 struct e1000_adapter *adapter = netdev_priv(netdev);
1472 WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
1473 e1000_down(adapter);
1474 e1000_power_down_phy(adapter);
1475 e1000_free_irq(adapter);
1477 e1000_free_all_tx_resources(adapter);
1478 e1000_free_all_rx_resources(adapter);
1480 /* kill manageability vlan ID if supported, but not if a vlan with
1481 * the same ID is registered on the host OS (let 8021q kill it) */
1482 if ((adapter->hw.mng_cookie.status &
1483 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
1485 vlan_group_get_device(adapter->vlgrp, adapter->mng_vlan_id))) {
1486 e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
1489 /* If AMT is enabled, let the firmware know that the network
1490 * interface is now closed */
1491 if (adapter->hw.mac_type == e1000_82573 &&
1492 e1000_check_mng_mode(&adapter->hw))
1493 e1000_release_hw_control(adapter);
1499 * e1000_check_64k_bound - check that memory doesn't cross 64kB boundary
1500 * @adapter: address of board private structure
1501 * @start: address of beginning of memory
1502 * @len: length of memory
1505 e1000_check_64k_bound(struct e1000_adapter *adapter,
1506 void *start, unsigned long len)
1508 unsigned long begin = (unsigned long) start;
1509 unsigned long end = begin + len;
1511 /* First rev 82545 and 82546 need to not allow any memory
1512 * write location to cross 64k boundary due to errata 23 */
1513 if (adapter->hw.mac_type == e1000_82545 ||
1514 adapter->hw.mac_type == e1000_82546) {
1515 return ((begin ^ (end - 1)) >> 16) != 0 ? FALSE : TRUE;
1522 * e1000_setup_tx_resources - allocate Tx resources (Descriptors)
1523 * @adapter: board private structure
1524 * @txdr: tx descriptor ring (for a specific queue) to setup
1526 * Return 0 on success, negative on failure
1530 e1000_setup_tx_resources(struct e1000_adapter *adapter,
1531 struct e1000_tx_ring *txdr)
1533 struct pci_dev *pdev = adapter->pdev;
1536 size = sizeof(struct e1000_buffer) * txdr->count;
1537 txdr->buffer_info = vmalloc(size);
1538 if (!txdr->buffer_info) {
1540 "Unable to allocate memory for the transmit descriptor ring\n");
1543 memset(txdr->buffer_info, 0, size);
1545 /* round up to nearest 4K */
1547 txdr->size = txdr->count * sizeof(struct e1000_tx_desc);
1548 E1000_ROUNDUP(txdr->size, 4096);
1550 txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
1553 vfree(txdr->buffer_info);
1555 "Unable to allocate memory for the transmit descriptor ring\n");
1559 /* Fix for errata 23, can't cross 64kB boundary */
1560 if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
1561 void *olddesc = txdr->desc;
1562 dma_addr_t olddma = txdr->dma;
1563 DPRINTK(TX_ERR, ERR, "txdr align check failed: %u bytes "
1564 "at %p\n", txdr->size, txdr->desc);
1565 /* Try again, without freeing the previous */
1566 txdr->desc = pci_alloc_consistent(pdev, txdr->size, &txdr->dma);
1567 /* Failed allocation, critical failure */
1569 pci_free_consistent(pdev, txdr->size, olddesc, olddma);
1570 goto setup_tx_desc_die;
1573 if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
1575 pci_free_consistent(pdev, txdr->size, txdr->desc,
1577 pci_free_consistent(pdev, txdr->size, olddesc, olddma);
1579 "Unable to allocate aligned memory "
1580 "for the transmit descriptor ring\n");
1581 vfree(txdr->buffer_info);
1584 /* Free old allocation, new allocation was successful */
1585 pci_free_consistent(pdev, txdr->size, olddesc, olddma);
1588 memset(txdr->desc, 0, txdr->size);
1590 txdr->next_to_use = 0;
1591 txdr->next_to_clean = 0;
1592 spin_lock_init(&txdr->tx_lock);
1598 * e1000_setup_all_tx_resources - wrapper to allocate Tx resources
1599 * (Descriptors) for all queues
1600 * @adapter: board private structure
1602 * Return 0 on success, negative on failure
1606 e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
1610 for (i = 0; i < adapter->num_tx_queues; i++) {
1611 err = e1000_setup_tx_resources(adapter, &adapter->tx_ring[i]);
1614 "Allocation for Tx Queue %u failed\n", i);
1615 for (i-- ; i >= 0; i--)
1616 e1000_free_tx_resources(adapter,
1617 &adapter->tx_ring[i]);
1626 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
1627 * @adapter: board private structure
1629 * Configure the Tx unit of the MAC after a reset.
1633 e1000_configure_tx(struct e1000_adapter *adapter)
1636 struct e1000_hw *hw = &adapter->hw;
1637 uint32_t tdlen, tctl, tipg, tarc;
1638 uint32_t ipgr1, ipgr2;
1640 /* Setup the HW Tx Head and Tail descriptor pointers */
1642 switch (adapter->num_tx_queues) {
1645 tdba = adapter->tx_ring[0].dma;
1646 tdlen = adapter->tx_ring[0].count *
1647 sizeof(struct e1000_tx_desc);
1648 E1000_WRITE_REG(hw, TDLEN, tdlen);
1649 E1000_WRITE_REG(hw, TDBAH, (tdba >> 32));
1650 E1000_WRITE_REG(hw, TDBAL, (tdba & 0x00000000ffffffffULL));
1651 E1000_WRITE_REG(hw, TDT, 0);
1652 E1000_WRITE_REG(hw, TDH, 0);
1653 adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ? E1000_TDH : E1000_82542_TDH);
1654 adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ? E1000_TDT : E1000_82542_TDT);
1658 /* Set the default values for the Tx Inter Packet Gap timer */
1659 if (adapter->hw.mac_type <= e1000_82547_rev_2 &&
1660 (hw->media_type == e1000_media_type_fiber ||
1661 hw->media_type == e1000_media_type_internal_serdes))
1662 tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
1664 tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
1666 switch (hw->mac_type) {
1667 case e1000_82542_rev2_0:
1668 case e1000_82542_rev2_1:
1669 tipg = DEFAULT_82542_TIPG_IPGT;
1670 ipgr1 = DEFAULT_82542_TIPG_IPGR1;
1671 ipgr2 = DEFAULT_82542_TIPG_IPGR2;
1673 case e1000_80003es2lan:
1674 ipgr1 = DEFAULT_82543_TIPG_IPGR1;
1675 ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2;
1678 ipgr1 = DEFAULT_82543_TIPG_IPGR1;
1679 ipgr2 = DEFAULT_82543_TIPG_IPGR2;
1682 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
1683 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
1684 E1000_WRITE_REG(hw, TIPG, tipg);
1686 /* Set the Tx Interrupt Delay register */
1688 E1000_WRITE_REG(hw, TIDV, adapter->tx_int_delay);
1689 if (hw->mac_type >= e1000_82540)
1690 E1000_WRITE_REG(hw, TADV, adapter->tx_abs_int_delay);
1692 /* Program the Transmit Control Register */
1694 tctl = E1000_READ_REG(hw, TCTL);
1695 tctl &= ~E1000_TCTL_CT;
1696 tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
1697 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
1699 if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) {
1700 tarc = E1000_READ_REG(hw, TARC0);
1701 /* set the speed mode bit, we'll clear it if we're not at
1702 * gigabit link later */
1704 E1000_WRITE_REG(hw, TARC0, tarc);
1705 } else if (hw->mac_type == e1000_80003es2lan) {
1706 tarc = E1000_READ_REG(hw, TARC0);
1708 E1000_WRITE_REG(hw, TARC0, tarc);
1709 tarc = E1000_READ_REG(hw, TARC1);
1711 E1000_WRITE_REG(hw, TARC1, tarc);
1714 e1000_config_collision_dist(hw);
1716 /* Setup Transmit Descriptor Settings for eop descriptor */
1717 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
1719 /* only set IDE if we are delaying interrupts using the timers */
1720 if (adapter->tx_int_delay)
1721 adapter->txd_cmd |= E1000_TXD_CMD_IDE;
1723 if (hw->mac_type < e1000_82543)
1724 adapter->txd_cmd |= E1000_TXD_CMD_RPS;
1726 adapter->txd_cmd |= E1000_TXD_CMD_RS;
1728 /* Cache if we're 82544 running in PCI-X because we'll
1729 * need this to apply a workaround later in the send path. */
1730 if (hw->mac_type == e1000_82544 &&
1731 hw->bus_type == e1000_bus_type_pcix)
1732 adapter->pcix_82544 = 1;
1734 E1000_WRITE_REG(hw, TCTL, tctl);
1739 * e1000_setup_rx_resources - allocate Rx resources (Descriptors)
1740 * @adapter: board private structure
1741 * @rxdr: rx descriptor ring (for a specific queue) to setup
1743 * Returns 0 on success, negative on failure
1747 e1000_setup_rx_resources(struct e1000_adapter *adapter,
1748 struct e1000_rx_ring *rxdr)
1750 struct pci_dev *pdev = adapter->pdev;
1753 size = sizeof(struct e1000_buffer) * rxdr->count;
1754 rxdr->buffer_info = vmalloc(size);
1755 if (!rxdr->buffer_info) {
1757 "Unable to allocate memory for the receive descriptor ring\n");
1760 memset(rxdr->buffer_info, 0, size);
1762 size = sizeof(struct e1000_ps_page) * rxdr->count;
1763 rxdr->ps_page = kmalloc(size, GFP_KERNEL);
1764 if (!rxdr->ps_page) {
1765 vfree(rxdr->buffer_info);
1767 "Unable to allocate memory for the receive descriptor ring\n");
1770 memset(rxdr->ps_page, 0, size);
1772 size = sizeof(struct e1000_ps_page_dma) * rxdr->count;
1773 rxdr->ps_page_dma = kmalloc(size, GFP_KERNEL);
1774 if (!rxdr->ps_page_dma) {
1775 vfree(rxdr->buffer_info);
1776 kfree(rxdr->ps_page);
1778 "Unable to allocate memory for the receive descriptor ring\n");
1781 memset(rxdr->ps_page_dma, 0, size);
1783 if (adapter->hw.mac_type <= e1000_82547_rev_2)
1784 desc_len = sizeof(struct e1000_rx_desc);
1786 desc_len = sizeof(union e1000_rx_desc_packet_split);
1788 /* Round up to nearest 4K */
1790 rxdr->size = rxdr->count * desc_len;
1791 E1000_ROUNDUP(rxdr->size, 4096);
1793 rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
1797 "Unable to allocate memory for the receive descriptor ring\n");
1799 vfree(rxdr->buffer_info);
1800 kfree(rxdr->ps_page);
1801 kfree(rxdr->ps_page_dma);
1805 /* Fix for errata 23, can't cross 64kB boundary */
1806 if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
1807 void *olddesc = rxdr->desc;
1808 dma_addr_t olddma = rxdr->dma;
1809 DPRINTK(RX_ERR, ERR, "rxdr align check failed: %u bytes "
1810 "at %p\n", rxdr->size, rxdr->desc);
1811 /* Try again, without freeing the previous */
1812 rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma);
1813 /* Failed allocation, critical failure */
1815 pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
1817 "Unable to allocate memory "
1818 "for the receive descriptor ring\n");
1819 goto setup_rx_desc_die;
1822 if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
1824 pci_free_consistent(pdev, rxdr->size, rxdr->desc,
1826 pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
1828 "Unable to allocate aligned memory "
1829 "for the receive descriptor ring\n");
1830 goto setup_rx_desc_die;
1832 /* Free old allocation, new allocation was successful */
1833 pci_free_consistent(pdev, rxdr->size, olddesc, olddma);
1836 memset(rxdr->desc, 0, rxdr->size);
1838 rxdr->next_to_clean = 0;
1839 rxdr->next_to_use = 0;
1845 * e1000_setup_all_rx_resources - wrapper to allocate Rx resources
1846 * (Descriptors) for all queues
1847 * @adapter: board private structure
1849 * Return 0 on success, negative on failure
1853 e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
1857 for (i = 0; i < adapter->num_rx_queues; i++) {
1858 err = e1000_setup_rx_resources(adapter, &adapter->rx_ring[i]);
1861 "Allocation for Rx Queue %u failed\n", i);
1862 for (i-- ; i >= 0; i--)
1863 e1000_free_rx_resources(adapter,
1864 &adapter->rx_ring[i]);
1873 * e1000_setup_rctl - configure the receive control registers
1874 * @adapter: Board private structure
1876 #define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \
1877 (((S) & (PAGE_SIZE - 1)) ? 1 : 0))
1879 e1000_setup_rctl(struct e1000_adapter *adapter)
1881 uint32_t rctl, rfctl;
1882 uint32_t psrctl = 0;
1883 #ifndef CONFIG_E1000_DISABLE_PACKET_SPLIT
1887 rctl = E1000_READ_REG(&adapter->hw, RCTL);
1889 rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
1891 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
1892 E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
1893 (adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT);
1895 if (adapter->hw.tbi_compatibility_on == 1)
1896 rctl |= E1000_RCTL_SBP;
1898 rctl &= ~E1000_RCTL_SBP;
1900 if (adapter->netdev->mtu <= ETH_DATA_LEN)
1901 rctl &= ~E1000_RCTL_LPE;
1903 rctl |= E1000_RCTL_LPE;
1905 /* Setup buffer sizes */
1906 rctl &= ~E1000_RCTL_SZ_4096;
1907 rctl |= E1000_RCTL_BSEX;
1908 switch (adapter->rx_buffer_len) {
1909 case E1000_RXBUFFER_256:
1910 rctl |= E1000_RCTL_SZ_256;
1911 rctl &= ~E1000_RCTL_BSEX;
1913 case E1000_RXBUFFER_512:
1914 rctl |= E1000_RCTL_SZ_512;
1915 rctl &= ~E1000_RCTL_BSEX;
1917 case E1000_RXBUFFER_1024:
1918 rctl |= E1000_RCTL_SZ_1024;
1919 rctl &= ~E1000_RCTL_BSEX;
1921 case E1000_RXBUFFER_2048:
1923 rctl |= E1000_RCTL_SZ_2048;
1924 rctl &= ~E1000_RCTL_BSEX;
1926 case E1000_RXBUFFER_4096:
1927 rctl |= E1000_RCTL_SZ_4096;
1929 case E1000_RXBUFFER_8192:
1930 rctl |= E1000_RCTL_SZ_8192;
1932 case E1000_RXBUFFER_16384:
1933 rctl |= E1000_RCTL_SZ_16384;
1937 #ifndef CONFIG_E1000_DISABLE_PACKET_SPLIT
1938 /* 82571 and greater support packet-split where the protocol
1939 * header is placed in skb->data and the packet data is
1940 * placed in pages hanging off of skb_shinfo(skb)->nr_frags.
1941 * In the case of a non-split, skb->data is linearly filled,
1942 * followed by the page buffers. Therefore, skb->data is
1943 * sized to hold the largest protocol header.
1945 /* allocations using alloc_page take too long for regular MTU
1946 * so only enable packet split for jumbo frames */
1947 pages = PAGE_USE_COUNT(adapter->netdev->mtu);
1948 if ((adapter->hw.mac_type >= e1000_82571) && (pages <= 3) &&
1949 PAGE_SIZE <= 16384 && (rctl & E1000_RCTL_LPE))
1950 adapter->rx_ps_pages = pages;
1952 adapter->rx_ps_pages = 0;
1954 if (adapter->rx_ps_pages) {
1955 /* Configure extra packet-split registers */
1956 rfctl = E1000_READ_REG(&adapter->hw, RFCTL);
1957 rfctl |= E1000_RFCTL_EXTEN;
1958 /* disable packet split support for IPv6 extension headers,
1959 * because some malformed IPv6 headers can hang the RX */
1960 rfctl |= (E1000_RFCTL_IPV6_EX_DIS |
1961 E1000_RFCTL_NEW_IPV6_EXT_DIS);
1963 E1000_WRITE_REG(&adapter->hw, RFCTL, rfctl);
1965 rctl |= E1000_RCTL_DTYP_PS;
1967 psrctl |= adapter->rx_ps_bsize0 >>
1968 E1000_PSRCTL_BSIZE0_SHIFT;
1970 switch (adapter->rx_ps_pages) {
1972 psrctl |= PAGE_SIZE <<
1973 E1000_PSRCTL_BSIZE3_SHIFT;
1975 psrctl |= PAGE_SIZE <<
1976 E1000_PSRCTL_BSIZE2_SHIFT;
1978 psrctl |= PAGE_SIZE >>
1979 E1000_PSRCTL_BSIZE1_SHIFT;
1983 E1000_WRITE_REG(&adapter->hw, PSRCTL, psrctl);
1986 E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
1990 * e1000_configure_rx - Configure 8254x Receive Unit after Reset
1991 * @adapter: board private structure
1993 * Configure the Rx unit of the MAC after a reset.
1997 e1000_configure_rx(struct e1000_adapter *adapter)
2000 struct e1000_hw *hw = &adapter->hw;
2001 uint32_t rdlen, rctl, rxcsum, ctrl_ext;
2003 if (adapter->rx_ps_pages) {
2004 /* this is a 32 byte descriptor */
2005 rdlen = adapter->rx_ring[0].count *
2006 sizeof(union e1000_rx_desc_packet_split);
2007 adapter->clean_rx = e1000_clean_rx_irq_ps;
2008 adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps;
2010 rdlen = adapter->rx_ring[0].count *
2011 sizeof(struct e1000_rx_desc);
2012 adapter->clean_rx = e1000_clean_rx_irq;
2013 adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
2016 /* disable receives while setting up the descriptors */
2017 rctl = E1000_READ_REG(hw, RCTL);
2018 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
2020 /* set the Receive Delay Timer Register */
2021 E1000_WRITE_REG(hw, RDTR, adapter->rx_int_delay);
2023 if (hw->mac_type >= e1000_82540) {
2024 E1000_WRITE_REG(hw, RADV, adapter->rx_abs_int_delay);
2025 if (adapter->itr_setting != 0)
2026 E1000_WRITE_REG(hw, ITR,
2027 1000000000 / (adapter->itr * 256));
2030 if (hw->mac_type >= e1000_82571) {
2031 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
2032 /* Reset delay timers after every interrupt */
2033 ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
2034 #ifdef CONFIG_E1000_NAPI
2035 /* Auto-Mask interrupts upon ICR access */
2036 ctrl_ext |= E1000_CTRL_EXT_IAME;
2037 E1000_WRITE_REG(hw, IAM, 0xffffffff);
2039 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
2040 E1000_WRITE_FLUSH(hw);
2043 /* Setup the HW Rx Head and Tail Descriptor Pointers and
2044 * the Base and Length of the Rx Descriptor Ring */
2045 switch (adapter->num_rx_queues) {
2048 rdba = adapter->rx_ring[0].dma;
2049 E1000_WRITE_REG(hw, RDLEN, rdlen);
2050 E1000_WRITE_REG(hw, RDBAH, (rdba >> 32));
2051 E1000_WRITE_REG(hw, RDBAL, (rdba & 0x00000000ffffffffULL));
2052 E1000_WRITE_REG(hw, RDT, 0);
2053 E1000_WRITE_REG(hw, RDH, 0);
2054 adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ? E1000_RDH : E1000_82542_RDH);
2055 adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ? E1000_RDT : E1000_82542_RDT);
2059 /* Enable 82543 Receive Checksum Offload for TCP and UDP */
2060 if (hw->mac_type >= e1000_82543) {
2061 rxcsum = E1000_READ_REG(hw, RXCSUM);
2062 if (adapter->rx_csum == TRUE) {
2063 rxcsum |= E1000_RXCSUM_TUOFL;
2065 /* Enable 82571 IPv4 payload checksum for UDP fragments
2066 * Must be used in conjunction with packet-split. */
2067 if ((hw->mac_type >= e1000_82571) &&
2068 (adapter->rx_ps_pages)) {
2069 rxcsum |= E1000_RXCSUM_IPPCSE;
2072 rxcsum &= ~E1000_RXCSUM_TUOFL;
2073 /* don't need to clear IPPCSE as it defaults to 0 */
2075 E1000_WRITE_REG(hw, RXCSUM, rxcsum);
2078 /* enable early receives on 82573, only takes effect if using > 2048
2079 * byte total frame size. for example only for jumbo frames */
2080 #define E1000_ERT_2048 0x100
2081 if (hw->mac_type == e1000_82573)
2082 E1000_WRITE_REG(hw, ERT, E1000_ERT_2048);
2084 /* Enable Receives */
2085 E1000_WRITE_REG(hw, RCTL, rctl);
2089 * e1000_free_tx_resources - Free Tx Resources per Queue
2090 * @adapter: board private structure
2091 * @tx_ring: Tx descriptor ring for a specific queue
2093 * Free all transmit software resources
2097 e1000_free_tx_resources(struct e1000_adapter *adapter,
2098 struct e1000_tx_ring *tx_ring)
2100 struct pci_dev *pdev = adapter->pdev;
2102 e1000_clean_tx_ring(adapter, tx_ring);
2104 vfree(tx_ring->buffer_info);
2105 tx_ring->buffer_info = NULL;
2107 pci_free_consistent(pdev, tx_ring->size, tx_ring->desc, tx_ring->dma);
2109 tx_ring->desc = NULL;
2113 * e1000_free_all_tx_resources - Free Tx Resources for All Queues
2114 * @adapter: board private structure
2116 * Free all transmit software resources
2120 e1000_free_all_tx_resources(struct e1000_adapter *adapter)
2124 for (i = 0; i < adapter->num_tx_queues; i++)
2125 e1000_free_tx_resources(adapter, &adapter->tx_ring[i]);
2129 e1000_unmap_and_free_tx_resource(struct e1000_adapter *adapter,
2130 struct e1000_buffer *buffer_info)
2132 if (buffer_info->dma) {
2133 pci_unmap_page(adapter->pdev,
2135 buffer_info->length,
2137 buffer_info->dma = 0;
2139 if (buffer_info->skb) {
2140 dev_kfree_skb_any(buffer_info->skb);
2141 buffer_info->skb = NULL;
2143 /* buffer_info must be completely set up in the transmit path */
2147 * e1000_clean_tx_ring - Free Tx Buffers
2148 * @adapter: board private structure
2149 * @tx_ring: ring to be cleaned
2153 e1000_clean_tx_ring(struct e1000_adapter *adapter,
2154 struct e1000_tx_ring *tx_ring)
2156 struct e1000_buffer *buffer_info;
2160 /* Free all the Tx ring sk_buffs */
2162 for (i = 0; i < tx_ring->count; i++) {
2163 buffer_info = &tx_ring->buffer_info[i];
2164 e1000_unmap_and_free_tx_resource(adapter, buffer_info);
2167 size = sizeof(struct e1000_buffer) * tx_ring->count;
2168 memset(tx_ring->buffer_info, 0, size);
2170 /* Zero out the descriptor ring */
2172 memset(tx_ring->desc, 0, tx_ring->size);
2174 tx_ring->next_to_use = 0;
2175 tx_ring->next_to_clean = 0;
2176 tx_ring->last_tx_tso = 0;
2178 writel(0, adapter->hw.hw_addr + tx_ring->tdh);
2179 writel(0, adapter->hw.hw_addr + tx_ring->tdt);
2183 * e1000_clean_all_tx_rings - Free Tx Buffers for all queues
2184 * @adapter: board private structure
2188 e1000_clean_all_tx_rings(struct e1000_adapter *adapter)
2192 for (i = 0; i < adapter->num_tx_queues; i++)
2193 e1000_clean_tx_ring(adapter, &adapter->tx_ring[i]);
2197 * e1000_free_rx_resources - Free Rx Resources
2198 * @adapter: board private structure
2199 * @rx_ring: ring to clean the resources from
2201 * Free all receive software resources
2205 e1000_free_rx_resources(struct e1000_adapter *adapter,
2206 struct e1000_rx_ring *rx_ring)
2208 struct pci_dev *pdev = adapter->pdev;
2210 e1000_clean_rx_ring(adapter, rx_ring);
2212 vfree(rx_ring->buffer_info);
2213 rx_ring->buffer_info = NULL;
2214 kfree(rx_ring->ps_page);
2215 rx_ring->ps_page = NULL;
2216 kfree(rx_ring->ps_page_dma);
2217 rx_ring->ps_page_dma = NULL;
2219 pci_free_consistent(pdev, rx_ring->size, rx_ring->desc, rx_ring->dma);
2221 rx_ring->desc = NULL;
2225 * e1000_free_all_rx_resources - Free Rx Resources for All Queues
2226 * @adapter: board private structure
2228 * Free all receive software resources
2232 e1000_free_all_rx_resources(struct e1000_adapter *adapter)
2236 for (i = 0; i < adapter->num_rx_queues; i++)
2237 e1000_free_rx_resources(adapter, &adapter->rx_ring[i]);
2241 * e1000_clean_rx_ring - Free Rx Buffers per Queue
2242 * @adapter: board private structure
2243 * @rx_ring: ring to free buffers from
2247 e1000_clean_rx_ring(struct e1000_adapter *adapter,
2248 struct e1000_rx_ring *rx_ring)
2250 struct e1000_buffer *buffer_info;
2251 struct e1000_ps_page *ps_page;
2252 struct e1000_ps_page_dma *ps_page_dma;
2253 struct pci_dev *pdev = adapter->pdev;
2257 /* Free all the Rx ring sk_buffs */
2258 for (i = 0; i < rx_ring->count; i++) {
2259 buffer_info = &rx_ring->buffer_info[i];
2260 if (buffer_info->skb) {
2261 pci_unmap_single(pdev,
2263 buffer_info->length,
2264 PCI_DMA_FROMDEVICE);
2266 dev_kfree_skb(buffer_info->skb);
2267 buffer_info->skb = NULL;
2269 ps_page = &rx_ring->ps_page[i];
2270 ps_page_dma = &rx_ring->ps_page_dma[i];
2271 for (j = 0; j < adapter->rx_ps_pages; j++) {
2272 if (!ps_page->ps_page[j]) break;
2273 pci_unmap_page(pdev,
2274 ps_page_dma->ps_page_dma[j],
2275 PAGE_SIZE, PCI_DMA_FROMDEVICE);
2276 ps_page_dma->ps_page_dma[j] = 0;
2277 put_page(ps_page->ps_page[j]);
2278 ps_page->ps_page[j] = NULL;
2282 size = sizeof(struct e1000_buffer) * rx_ring->count;
2283 memset(rx_ring->buffer_info, 0, size);
2284 size = sizeof(struct e1000_ps_page) * rx_ring->count;
2285 memset(rx_ring->ps_page, 0, size);
2286 size = sizeof(struct e1000_ps_page_dma) * rx_ring->count;
2287 memset(rx_ring->ps_page_dma, 0, size);
2289 /* Zero out the descriptor ring */
2291 memset(rx_ring->desc, 0, rx_ring->size);
2293 rx_ring->next_to_clean = 0;
2294 rx_ring->next_to_use = 0;
2296 writel(0, adapter->hw.hw_addr + rx_ring->rdh);
2297 writel(0, adapter->hw.hw_addr + rx_ring->rdt);
2301 * e1000_clean_all_rx_rings - Free Rx Buffers for all queues
2302 * @adapter: board private structure
2306 e1000_clean_all_rx_rings(struct e1000_adapter *adapter)
2310 for (i = 0; i < adapter->num_rx_queues; i++)
2311 e1000_clean_rx_ring(adapter, &adapter->rx_ring[i]);
2314 /* The 82542 2.0 (revision 2) needs to have the receive unit in reset
2315 * and memory write and invalidate disabled for certain operations
2318 e1000_enter_82542_rst(struct e1000_adapter *adapter)
2320 struct net_device *netdev = adapter->netdev;
2323 e1000_pci_clear_mwi(&adapter->hw);
2325 rctl = E1000_READ_REG(&adapter->hw, RCTL);
2326 rctl |= E1000_RCTL_RST;
2327 E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
2328 E1000_WRITE_FLUSH(&adapter->hw);
2331 if (netif_running(netdev))
2332 e1000_clean_all_rx_rings(adapter);
2336 e1000_leave_82542_rst(struct e1000_adapter *adapter)
2338 struct net_device *netdev = adapter->netdev;
2341 rctl = E1000_READ_REG(&adapter->hw, RCTL);
2342 rctl &= ~E1000_RCTL_RST;
2343 E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
2344 E1000_WRITE_FLUSH(&adapter->hw);
2347 if (adapter->hw.pci_cmd_word & PCI_COMMAND_INVALIDATE)
2348 e1000_pci_set_mwi(&adapter->hw);
2350 if (netif_running(netdev)) {
2351 /* No need to loop, because 82542 supports only 1 queue */
2352 struct e1000_rx_ring *ring = &adapter->rx_ring[0];
2353 e1000_configure_rx(adapter);
2354 adapter->alloc_rx_buf(adapter, ring, E1000_DESC_UNUSED(ring));
2359 * e1000_set_mac - Change the Ethernet Address of the NIC
2360 * @netdev: network interface device structure
2361 * @p: pointer to an address structure
2363 * Returns 0 on success, negative on failure
2367 e1000_set_mac(struct net_device *netdev, void *p)
2369 struct e1000_adapter *adapter = netdev_priv(netdev);
2370 struct sockaddr *addr = p;
2372 if (!is_valid_ether_addr(addr->sa_data))
2373 return -EADDRNOTAVAIL;
2375 /* 82542 2.0 needs to be in reset to write receive address registers */
2377 if (adapter->hw.mac_type == e1000_82542_rev2_0)
2378 e1000_enter_82542_rst(adapter);
2380 memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
2381 memcpy(adapter->hw.mac_addr, addr->sa_data, netdev->addr_len);
2383 e1000_rar_set(&adapter->hw, adapter->hw.mac_addr, 0);
2385 /* With 82571 controllers, LAA may be overwritten (with the default)
2386 * due to controller reset from the other port. */
2387 if (adapter->hw.mac_type == e1000_82571) {
2388 /* activate the work around */
2389 adapter->hw.laa_is_present = 1;
2391 /* Hold a copy of the LAA in RAR[14] This is done so that
2392 * between the time RAR[0] gets clobbered and the time it
2393 * gets fixed (in e1000_watchdog), the actual LAA is in one
2394 * of the RARs and no incoming packets directed to this port
2395 * are dropped. Eventaully the LAA will be in RAR[0] and
2397 e1000_rar_set(&adapter->hw, adapter->hw.mac_addr,
2398 E1000_RAR_ENTRIES - 1);
2401 if (adapter->hw.mac_type == e1000_82542_rev2_0)
2402 e1000_leave_82542_rst(adapter);
2408 * e1000_set_multi - Multicast and Promiscuous mode set
2409 * @netdev: network interface device structure
2411 * The set_multi entry point is called whenever the multicast address
2412 * list or the network interface flags are updated. This routine is
2413 * responsible for configuring the hardware for proper multicast,
2414 * promiscuous mode, and all-multi behavior.
2418 e1000_set_multi(struct net_device *netdev)
2420 struct e1000_adapter *adapter = netdev_priv(netdev);
2421 struct e1000_hw *hw = &adapter->hw;
2422 struct dev_mc_list *mc_ptr;
2424 uint32_t hash_value;
2425 int i, rar_entries = E1000_RAR_ENTRIES;
2426 int mta_reg_count = (hw->mac_type == e1000_ich8lan) ?
2427 E1000_NUM_MTA_REGISTERS_ICH8LAN :
2428 E1000_NUM_MTA_REGISTERS;
2430 if (adapter->hw.mac_type == e1000_ich8lan)
2431 rar_entries = E1000_RAR_ENTRIES_ICH8LAN;
2433 /* reserve RAR[14] for LAA over-write work-around */
2434 if (adapter->hw.mac_type == e1000_82571)
2437 /* Check for Promiscuous and All Multicast modes */
2439 rctl = E1000_READ_REG(hw, RCTL);
2441 if (netdev->flags & IFF_PROMISC) {
2442 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
2443 } else if (netdev->flags & IFF_ALLMULTI) {
2444 rctl |= E1000_RCTL_MPE;
2445 rctl &= ~E1000_RCTL_UPE;
2447 rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE);
2450 E1000_WRITE_REG(hw, RCTL, rctl);
2452 /* 82542 2.0 needs to be in reset to write receive address registers */
2454 if (hw->mac_type == e1000_82542_rev2_0)
2455 e1000_enter_82542_rst(adapter);
2457 /* load the first 14 multicast address into the exact filters 1-14
2458 * RAR 0 is used for the station MAC adddress
2459 * if there are not 14 addresses, go ahead and clear the filters
2460 * -- with 82571 controllers only 0-13 entries are filled here
2462 mc_ptr = netdev->mc_list;
2464 for (i = 1; i < rar_entries; i++) {
2466 e1000_rar_set(hw, mc_ptr->dmi_addr, i);
2467 mc_ptr = mc_ptr->next;
2469 E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0);
2470 E1000_WRITE_FLUSH(hw);
2471 E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0);
2472 E1000_WRITE_FLUSH(hw);
2476 /* clear the old settings from the multicast hash table */
2478 for (i = 0; i < mta_reg_count; i++) {
2479 E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
2480 E1000_WRITE_FLUSH(hw);
2483 /* load any remaining addresses into the hash table */
2485 for (; mc_ptr; mc_ptr = mc_ptr->next) {
2486 hash_value = e1000_hash_mc_addr(hw, mc_ptr->dmi_addr);
2487 e1000_mta_set(hw, hash_value);
2490 if (hw->mac_type == e1000_82542_rev2_0)
2491 e1000_leave_82542_rst(adapter);
2494 /* Need to wait a few seconds after link up to get diagnostic information from
2498 e1000_update_phy_info(unsigned long data)
2500 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
2501 e1000_phy_get_info(&adapter->hw, &adapter->phy_info);
2505 * e1000_82547_tx_fifo_stall - Timer Call-back
2506 * @data: pointer to adapter cast into an unsigned long
2510 e1000_82547_tx_fifo_stall(unsigned long data)
2512 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
2513 struct net_device *netdev = adapter->netdev;
2516 if (atomic_read(&adapter->tx_fifo_stall)) {
2517 if ((E1000_READ_REG(&adapter->hw, TDT) ==
2518 E1000_READ_REG(&adapter->hw, TDH)) &&
2519 (E1000_READ_REG(&adapter->hw, TDFT) ==
2520 E1000_READ_REG(&adapter->hw, TDFH)) &&
2521 (E1000_READ_REG(&adapter->hw, TDFTS) ==
2522 E1000_READ_REG(&adapter->hw, TDFHS))) {
2523 tctl = E1000_READ_REG(&adapter->hw, TCTL);
2524 E1000_WRITE_REG(&adapter->hw, TCTL,
2525 tctl & ~E1000_TCTL_EN);
2526 E1000_WRITE_REG(&adapter->hw, TDFT,
2527 adapter->tx_head_addr);
2528 E1000_WRITE_REG(&adapter->hw, TDFH,
2529 adapter->tx_head_addr);
2530 E1000_WRITE_REG(&adapter->hw, TDFTS,
2531 adapter->tx_head_addr);
2532 E1000_WRITE_REG(&adapter->hw, TDFHS,
2533 adapter->tx_head_addr);
2534 E1000_WRITE_REG(&adapter->hw, TCTL, tctl);
2535 E1000_WRITE_FLUSH(&adapter->hw);
2537 adapter->tx_fifo_head = 0;
2538 atomic_set(&adapter->tx_fifo_stall, 0);
2539 netif_wake_queue(netdev);
2541 mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1);
2547 * e1000_watchdog - Timer Call-back
2548 * @data: pointer to adapter cast into an unsigned long
2551 e1000_watchdog(unsigned long data)
2553 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
2554 struct net_device *netdev = adapter->netdev;
2555 struct e1000_tx_ring *txdr = adapter->tx_ring;
2556 uint32_t link, tctl;
2559 ret_val = e1000_check_for_link(&adapter->hw);
2560 if ((ret_val == E1000_ERR_PHY) &&
2561 (adapter->hw.phy_type == e1000_phy_igp_3) &&
2562 (E1000_READ_REG(&adapter->hw, CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
2563 /* See e1000_kumeran_lock_loss_workaround() */
2565 "Gigabit has been disabled, downgrading speed\n");
2568 if (adapter->hw.mac_type == e1000_82573) {
2569 e1000_enable_tx_pkt_filtering(&adapter->hw);
2570 if (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id)
2571 e1000_update_mng_vlan(adapter);
2574 if ((adapter->hw.media_type == e1000_media_type_internal_serdes) &&
2575 !(E1000_READ_REG(&adapter->hw, TXCW) & E1000_TXCW_ANE))
2576 link = !adapter->hw.serdes_link_down;
2578 link = E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU;
2581 if (!netif_carrier_ok(netdev)) {
2583 boolean_t txb2b = 1;
2584 e1000_get_speed_and_duplex(&adapter->hw,
2585 &adapter->link_speed,
2586 &adapter->link_duplex);
2588 ctrl = E1000_READ_REG(&adapter->hw, CTRL);
2589 DPRINTK(LINK, INFO, "NIC Link is Up %d Mbps %s, "
2590 "Flow Control: %s\n",
2591 adapter->link_speed,
2592 adapter->link_duplex == FULL_DUPLEX ?
2593 "Full Duplex" : "Half Duplex",
2594 ((ctrl & E1000_CTRL_TFCE) && (ctrl &
2595 E1000_CTRL_RFCE)) ? "RX/TX" : ((ctrl &
2596 E1000_CTRL_RFCE) ? "RX" : ((ctrl &
2597 E1000_CTRL_TFCE) ? "TX" : "None" )));
2599 /* tweak tx_queue_len according to speed/duplex
2600 * and adjust the timeout factor */
2601 netdev->tx_queue_len = adapter->tx_queue_len;
2602 adapter->tx_timeout_factor = 1;
2603 switch (adapter->link_speed) {
2606 netdev->tx_queue_len = 10;
2607 adapter->tx_timeout_factor = 8;
2611 netdev->tx_queue_len = 100;
2612 /* maybe add some timeout factor ? */
2616 if ((adapter->hw.mac_type == e1000_82571 ||
2617 adapter->hw.mac_type == e1000_82572) &&
2620 tarc0 = E1000_READ_REG(&adapter->hw, TARC0);
2621 tarc0 &= ~(1 << 21);
2622 E1000_WRITE_REG(&adapter->hw, TARC0, tarc0);
2625 /* disable TSO for pcie and 10/100 speeds, to avoid
2626 * some hardware issues */
2627 if (!adapter->tso_force &&
2628 adapter->hw.bus_type == e1000_bus_type_pci_express){
2629 switch (adapter->link_speed) {
2633 "10/100 speed: disabling TSO\n");
2634 netdev->features &= ~NETIF_F_TSO;
2635 netdev->features &= ~NETIF_F_TSO6;
2638 netdev->features |= NETIF_F_TSO;
2639 netdev->features |= NETIF_F_TSO6;
2647 /* enable transmits in the hardware, need to do this
2648 * after setting TARC0 */
2649 tctl = E1000_READ_REG(&adapter->hw, TCTL);
2650 tctl |= E1000_TCTL_EN;
2651 E1000_WRITE_REG(&adapter->hw, TCTL, tctl);
2653 netif_carrier_on(netdev);
2654 netif_wake_queue(netdev);
2655 mod_timer(&adapter->phy_info_timer, jiffies + 2 * HZ);
2656 adapter->smartspeed = 0;
2658 /* make sure the receive unit is started */
2659 if (adapter->hw.rx_needs_kicking) {
2660 struct e1000_hw *hw = &adapter->hw;
2661 uint32_t rctl = E1000_READ_REG(hw, RCTL);
2662 E1000_WRITE_REG(hw, RCTL, rctl | E1000_RCTL_EN);
2666 if (netif_carrier_ok(netdev)) {
2667 adapter->link_speed = 0;
2668 adapter->link_duplex = 0;
2669 DPRINTK(LINK, INFO, "NIC Link is Down\n");
2670 netif_carrier_off(netdev);
2671 netif_stop_queue(netdev);
2672 mod_timer(&adapter->phy_info_timer, jiffies + 2 * HZ);
2674 /* 80003ES2LAN workaround--
2675 * For packet buffer work-around on link down event;
2676 * disable receives in the ISR and
2677 * reset device here in the watchdog
2679 if (adapter->hw.mac_type == e1000_80003es2lan)
2681 schedule_work(&adapter->reset_task);
2684 e1000_smartspeed(adapter);
2687 e1000_update_stats(adapter);
2689 adapter->hw.tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
2690 adapter->tpt_old = adapter->stats.tpt;
2691 adapter->hw.collision_delta = adapter->stats.colc - adapter->colc_old;
2692 adapter->colc_old = adapter->stats.colc;
2694 adapter->gorcl = adapter->stats.gorcl - adapter->gorcl_old;
2695 adapter->gorcl_old = adapter->stats.gorcl;
2696 adapter->gotcl = adapter->stats.gotcl - adapter->gotcl_old;
2697 adapter->gotcl_old = adapter->stats.gotcl;
2699 e1000_update_adaptive(&adapter->hw);
2701 if (!netif_carrier_ok(netdev)) {
2702 if (E1000_DESC_UNUSED(txdr) + 1 < txdr->count) {
2703 /* We've lost link, so the controller stops DMA,
2704 * but we've got queued Tx work that's never going
2705 * to get done, so reset controller to flush Tx.
2706 * (Do the reset outside of interrupt context). */
2707 adapter->tx_timeout_count++;
2708 schedule_work(&adapter->reset_task);
2712 /* Cause software interrupt to ensure rx ring is cleaned */
2713 E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_RXDMT0);
2715 /* Force detection of hung controller every watchdog period */
2716 adapter->detect_tx_hung = TRUE;
2718 /* With 82571 controllers, LAA may be overwritten due to controller
2719 * reset from the other port. Set the appropriate LAA in RAR[0] */
2720 if (adapter->hw.mac_type == e1000_82571 && adapter->hw.laa_is_present)
2721 e1000_rar_set(&adapter->hw, adapter->hw.mac_addr, 0);
2723 /* Reset the timer */
2724 mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ);
2727 enum latency_range {
2731 latency_invalid = 255
2735 * e1000_update_itr - update the dynamic ITR value based on statistics
2736 * Stores a new ITR value based on packets and byte
2737 * counts during the last interrupt. The advantage of per interrupt
2738 * computation is faster updates and more accurate ITR for the current
2739 * traffic pattern. Constants in this function were computed
2740 * based on theoretical maximum wire speed and thresholds were set based
2741 * on testing data as well as attempting to minimize response time
2742 * while increasing bulk throughput.
2743 * this functionality is controlled by the InterruptThrottleRate module
2744 * parameter (see e1000_param.c)
2745 * @adapter: pointer to adapter
2746 * @itr_setting: current adapter->itr
2747 * @packets: the number of packets during this measurement interval
2748 * @bytes: the number of bytes during this measurement interval
2750 static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
2751 uint16_t itr_setting,
2755 unsigned int retval = itr_setting;
2756 struct e1000_hw *hw = &adapter->hw;
2758 if (unlikely(hw->mac_type < e1000_82540))
2759 goto update_itr_done;
2762 goto update_itr_done;
2764 switch (itr_setting) {
2765 case lowest_latency:
2766 /* jumbo frames get bulk treatment*/
2767 if (bytes/packets > 8000)
2768 retval = bulk_latency;
2769 else if ((packets < 5) && (bytes > 512))
2770 retval = low_latency;
2772 case low_latency: /* 50 usec aka 20000 ints/s */
2773 if (bytes > 10000) {
2774 /* jumbo frames need bulk latency setting */
2775 if (bytes/packets > 8000)
2776 retval = bulk_latency;
2777 else if ((packets < 10) || ((bytes/packets) > 1200))
2778 retval = bulk_latency;
2779 else if ((packets > 35))
2780 retval = lowest_latency;
2781 } else if (bytes/packets > 2000)
2782 retval = bulk_latency;
2783 else if (packets <= 2 && bytes < 512)
2784 retval = lowest_latency;
2786 case bulk_latency: /* 250 usec aka 4000 ints/s */
2787 if (bytes > 25000) {
2789 retval = low_latency;
2790 } else if (bytes < 6000) {
2791 retval = low_latency;
2800 static void e1000_set_itr(struct e1000_adapter *adapter)
2802 struct e1000_hw *hw = &adapter->hw;
2803 uint16_t current_itr;
2804 uint32_t new_itr = adapter->itr;
2806 if (unlikely(hw->mac_type < e1000_82540))
2809 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
2810 if (unlikely(adapter->link_speed != SPEED_1000)) {
2816 adapter->tx_itr = e1000_update_itr(adapter,
2818 adapter->total_tx_packets,
2819 adapter->total_tx_bytes);
2820 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2821 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
2822 adapter->tx_itr = low_latency;
2824 adapter->rx_itr = e1000_update_itr(adapter,
2826 adapter->total_rx_packets,
2827 adapter->total_rx_bytes);
2828 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2829 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
2830 adapter->rx_itr = low_latency;
2832 current_itr = max(adapter->rx_itr, adapter->tx_itr);
2834 switch (current_itr) {
2835 /* counts and packets in update_itr are dependent on these numbers */
2836 case lowest_latency:
2840 new_itr = 20000; /* aka hwitr = ~200 */
2850 if (new_itr != adapter->itr) {
2851 /* this attempts to bias the interrupt rate towards Bulk
2852 * by adding intermediate steps when interrupt rate is
2854 new_itr = new_itr > adapter->itr ?
2855 min(adapter->itr + (new_itr >> 2), new_itr) :
2857 adapter->itr = new_itr;
2858 E1000_WRITE_REG(hw, ITR, 1000000000 / (new_itr * 256));
2864 #define E1000_TX_FLAGS_CSUM 0x00000001
2865 #define E1000_TX_FLAGS_VLAN 0x00000002
2866 #define E1000_TX_FLAGS_TSO 0x00000004
2867 #define E1000_TX_FLAGS_IPV4 0x00000008
2868 #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
2869 #define E1000_TX_FLAGS_VLAN_SHIFT 16
2872 e1000_tso(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
2873 struct sk_buff *skb)
2875 struct e1000_context_desc *context_desc;
2876 struct e1000_buffer *buffer_info;
2878 uint32_t cmd_length = 0;
2879 uint16_t ipcse = 0, tucse, mss;
2880 uint8_t ipcss, ipcso, tucss, tucso, hdr_len;
2883 if (skb_is_gso(skb)) {
2884 if (skb_header_cloned(skb)) {
2885 err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
2890 hdr_len = ((skb->h.raw - skb->data) + (skb->h.th->doff << 2));
2891 mss = skb_shinfo(skb)->gso_size;
2892 if (skb->protocol == htons(ETH_P_IP)) {
2893 struct iphdr *iph = ip_hdr(skb);
2896 skb->h.th->check = ~csum_tcpudp_magic(iph->saddr,
2899 cmd_length = E1000_TXD_CMD_IP;
2900 ipcse = skb->h.raw - skb->data - 1;
2901 } else if (skb->protocol == htons(ETH_P_IPV6)) {
2902 ipv6_hdr(skb)->payload_len = 0;
2904 ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
2905 &ipv6_hdr(skb)->daddr,
2909 ipcss = skb_network_offset(skb);
2910 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
2911 tucss = skb->h.raw - skb->data;
2912 tucso = (void *)&(skb->h.th->check) - (void *)skb->data;
2915 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
2916 E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
2918 i = tx_ring->next_to_use;
2919 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
2920 buffer_info = &tx_ring->buffer_info[i];
2922 context_desc->lower_setup.ip_fields.ipcss = ipcss;
2923 context_desc->lower_setup.ip_fields.ipcso = ipcso;
2924 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
2925 context_desc->upper_setup.tcp_fields.tucss = tucss;
2926 context_desc->upper_setup.tcp_fields.tucso = tucso;
2927 context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
2928 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
2929 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
2930 context_desc->cmd_and_length = cpu_to_le32(cmd_length);
2932 buffer_info->time_stamp = jiffies;
2933 buffer_info->next_to_watch = i;
2935 if (++i == tx_ring->count) i = 0;
2936 tx_ring->next_to_use = i;
2944 e1000_tx_csum(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
2945 struct sk_buff *skb)
2947 struct e1000_context_desc *context_desc;
2948 struct e1000_buffer *buffer_info;
2952 if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
2953 css = skb->h.raw - skb->data;
2955 i = tx_ring->next_to_use;
2956 buffer_info = &tx_ring->buffer_info[i];
2957 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
2959 context_desc->lower_setup.ip_config = 0;
2960 context_desc->upper_setup.tcp_fields.tucss = css;
2961 context_desc->upper_setup.tcp_fields.tucso = css + skb->csum;
2962 context_desc->upper_setup.tcp_fields.tucse = 0;
2963 context_desc->tcp_seg_setup.data = 0;
2964 context_desc->cmd_and_length = cpu_to_le32(E1000_TXD_CMD_DEXT);
2966 buffer_info->time_stamp = jiffies;
2967 buffer_info->next_to_watch = i;
2969 if (unlikely(++i == tx_ring->count)) i = 0;
2970 tx_ring->next_to_use = i;
2978 #define E1000_MAX_TXD_PWR 12
2979 #define E1000_MAX_DATA_PER_TXD (1<<E1000_MAX_TXD_PWR)
2982 e1000_tx_map(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
2983 struct sk_buff *skb, unsigned int first, unsigned int max_per_txd,
2984 unsigned int nr_frags, unsigned int mss)
2986 struct e1000_buffer *buffer_info;
2987 unsigned int len = skb->len;
2988 unsigned int offset = 0, size, count = 0, i;
2990 len -= skb->data_len;
2992 i = tx_ring->next_to_use;
2995 buffer_info = &tx_ring->buffer_info[i];
2996 size = min(len, max_per_txd);
2997 /* Workaround for Controller erratum --
2998 * descriptor for non-tso packet in a linear SKB that follows a
2999 * tso gets written back prematurely before the data is fully
3000 * DMA'd to the controller */
3001 if (!skb->data_len && tx_ring->last_tx_tso &&
3003 tx_ring->last_tx_tso = 0;
3007 /* Workaround for premature desc write-backs
3008 * in TSO mode. Append 4-byte sentinel desc */
3009 if (unlikely(mss && !nr_frags && size == len && size > 8))
3011 /* work-around for errata 10 and it applies
3012 * to all controllers in PCI-X mode
3013 * The fix is to make sure that the first descriptor of a
3014 * packet is smaller than 2048 - 16 - 16 (or 2016) bytes
3016 if (unlikely((adapter->hw.bus_type == e1000_bus_type_pcix) &&
3017 (size > 2015) && count == 0))
3020 /* Workaround for potential 82544 hang in PCI-X. Avoid
3021 * terminating buffers within evenly-aligned dwords. */
3022 if (unlikely(adapter->pcix_82544 &&
3023 !((unsigned long)(skb->data + offset + size - 1) & 4) &&
3027 buffer_info->length = size;
3029 pci_map_single(adapter->pdev,
3033 buffer_info->time_stamp = jiffies;
3034 buffer_info->next_to_watch = i;
3039 if (unlikely(++i == tx_ring->count)) i = 0;
3042 for (f = 0; f < nr_frags; f++) {
3043 struct skb_frag_struct *frag;
3045 frag = &skb_shinfo(skb)->frags[f];
3047 offset = frag->page_offset;
3050 buffer_info = &tx_ring->buffer_info[i];
3051 size = min(len, max_per_txd);
3052 /* Workaround for premature desc write-backs
3053 * in TSO mode. Append 4-byte sentinel desc */
3054 if (unlikely(mss && f == (nr_frags-1) && size == len && size > 8))
3056 /* Workaround for potential 82544 hang in PCI-X.
3057 * Avoid terminating buffers within evenly-aligned
3059 if (unlikely(adapter->pcix_82544 &&
3060 !((unsigned long)(frag->page+offset+size-1) & 4) &&
3064 buffer_info->length = size;
3066 pci_map_page(adapter->pdev,
3071 buffer_info->time_stamp = jiffies;
3072 buffer_info->next_to_watch = i;
3077 if (unlikely(++i == tx_ring->count)) i = 0;
3081 i = (i == 0) ? tx_ring->count - 1 : i - 1;
3082 tx_ring->buffer_info[i].skb = skb;
3083 tx_ring->buffer_info[first].next_to_watch = i;
3089 e1000_tx_queue(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
3090 int tx_flags, int count)
3092 struct e1000_tx_desc *tx_desc = NULL;
3093 struct e1000_buffer *buffer_info;
3094 uint32_t txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
3097 if (likely(tx_flags & E1000_TX_FLAGS_TSO)) {
3098 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
3100 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
3102 if (likely(tx_flags & E1000_TX_FLAGS_IPV4))
3103 txd_upper |= E1000_TXD_POPTS_IXSM << 8;
3106 if (likely(tx_flags & E1000_TX_FLAGS_CSUM)) {
3107 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
3108 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
3111 if (unlikely(tx_flags & E1000_TX_FLAGS_VLAN)) {
3112 txd_lower |= E1000_TXD_CMD_VLE;
3113 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
3116 i = tx_ring->next_to_use;
3119 buffer_info = &tx_ring->buffer_info[i];
3120 tx_desc = E1000_TX_DESC(*tx_ring, i);
3121 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
3122 tx_desc->lower.data =
3123 cpu_to_le32(txd_lower | buffer_info->length);
3124 tx_desc->upper.data = cpu_to_le32(txd_upper);
3125 if (unlikely(++i == tx_ring->count)) i = 0;
3128 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
3130 /* Force memory writes to complete before letting h/w
3131 * know there are new descriptors to fetch. (Only
3132 * applicable for weak-ordered memory model archs,
3133 * such as IA-64). */
3136 tx_ring->next_to_use = i;
3137 writel(i, adapter->hw.hw_addr + tx_ring->tdt);
3138 /* we need this if more than one processor can write to our tail
3139 * at a time, it syncronizes IO on IA64/Altix systems */
3144 * 82547 workaround to avoid controller hang in half-duplex environment.
3145 * The workaround is to avoid queuing a large packet that would span
3146 * the internal Tx FIFO ring boundary by notifying the stack to resend
3147 * the packet at a later time. This gives the Tx FIFO an opportunity to
3148 * flush all packets. When that occurs, we reset the Tx FIFO pointers
3149 * to the beginning of the Tx FIFO.
3152 #define E1000_FIFO_HDR 0x10
3153 #define E1000_82547_PAD_LEN 0x3E0
3156 e1000_82547_fifo_workaround(struct e1000_adapter *adapter, struct sk_buff *skb)
3158 uint32_t fifo_space = adapter->tx_fifo_size - adapter->tx_fifo_head;
3159 uint32_t skb_fifo_len = skb->len + E1000_FIFO_HDR;
3161 E1000_ROUNDUP(skb_fifo_len, E1000_FIFO_HDR);
3163 if (adapter->link_duplex != HALF_DUPLEX)
3164 goto no_fifo_stall_required;
3166 if (atomic_read(&adapter->tx_fifo_stall))
3169 if (skb_fifo_len >= (E1000_82547_PAD_LEN + fifo_space)) {
3170 atomic_set(&adapter->tx_fifo_stall, 1);
3174 no_fifo_stall_required:
3175 adapter->tx_fifo_head += skb_fifo_len;
3176 if (adapter->tx_fifo_head >= adapter->tx_fifo_size)
3177 adapter->tx_fifo_head -= adapter->tx_fifo_size;
3181 #define MINIMUM_DHCP_PACKET_SIZE 282
3183 e1000_transfer_dhcp_info(struct e1000_adapter *adapter, struct sk_buff *skb)
3185 struct e1000_hw *hw = &adapter->hw;
3186 uint16_t length, offset;
3187 if (vlan_tx_tag_present(skb)) {
3188 if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
3189 ( adapter->hw.mng_cookie.status &
3190 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) )
3193 if (skb->len > MINIMUM_DHCP_PACKET_SIZE) {
3194 struct ethhdr *eth = (struct ethhdr *) skb->data;
3195 if ((htons(ETH_P_IP) == eth->h_proto)) {
3196 const struct iphdr *ip =
3197 (struct iphdr *)((uint8_t *)skb->data+14);
3198 if (IPPROTO_UDP == ip->protocol) {
3199 struct udphdr *udp =
3200 (struct udphdr *)((uint8_t *)ip +
3202 if (ntohs(udp->dest) == 67) {
3203 offset = (uint8_t *)udp + 8 - skb->data;
3204 length = skb->len - offset;
3206 return e1000_mng_write_dhcp_info(hw,
3216 static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
3218 struct e1000_adapter *adapter = netdev_priv(netdev);
3219 struct e1000_tx_ring *tx_ring = adapter->tx_ring;
3221 netif_stop_queue(netdev);
3222 /* Herbert's original patch had:
3223 * smp_mb__after_netif_stop_queue();
3224 * but since that doesn't exist yet, just open code it. */
3227 /* We need to check again in a case another CPU has just
3228 * made room available. */
3229 if (likely(E1000_DESC_UNUSED(tx_ring) < size))
3233 netif_start_queue(netdev);
3234 ++adapter->restart_queue;
3238 static int e1000_maybe_stop_tx(struct net_device *netdev,
3239 struct e1000_tx_ring *tx_ring, int size)
3241 if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
3243 return __e1000_maybe_stop_tx(netdev, size);
3246 #define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 )
3248 e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
3250 struct e1000_adapter *adapter = netdev_priv(netdev);
3251 struct e1000_tx_ring *tx_ring;
3252 unsigned int first, max_per_txd = E1000_MAX_DATA_PER_TXD;
3253 unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
3254 unsigned int tx_flags = 0;
3255 unsigned int len = skb->len;
3256 unsigned long flags;
3257 unsigned int nr_frags = 0;
3258 unsigned int mss = 0;
3262 len -= skb->data_len;
3264 /* This goes back to the question of how to logically map a tx queue
3265 * to a flow. Right now, performance is impacted slightly negatively
3266 * if using multiple tx queues. If the stack breaks away from a
3267 * single qdisc implementation, we can look at this again. */
3268 tx_ring = adapter->tx_ring;
3270 if (unlikely(skb->len <= 0)) {
3271 dev_kfree_skb_any(skb);
3272 return NETDEV_TX_OK;
3275 /* 82571 and newer doesn't need the workaround that limited descriptor
3277 if (adapter->hw.mac_type >= e1000_82571)
3280 mss = skb_shinfo(skb)->gso_size;
3281 /* The controller does a simple calculation to
3282 * make sure there is enough room in the FIFO before
3283 * initiating the DMA for each buffer. The calc is:
3284 * 4 = ceil(buffer len/mss). To make sure we don't
3285 * overrun the FIFO, adjust the max buffer len if mss
3289 max_per_txd = min(mss << 2, max_per_txd);
3290 max_txd_pwr = fls(max_per_txd) - 1;
3292 /* TSO Workaround for 82571/2/3 Controllers -- if skb->data
3293 * points to just header, pull a few bytes of payload from
3294 * frags into skb->data */
3295 hdr_len = ((skb->h.raw - skb->data) + (skb->h.th->doff << 2));
3296 if (skb->data_len && (hdr_len == (skb->len - skb->data_len))) {
3297 switch (adapter->hw.mac_type) {
3298 unsigned int pull_size;
3300 /* Make sure we have room to chop off 4 bytes,
3301 * and that the end alignment will work out to
3302 * this hardware's requirements
3303 * NOTE: this is a TSO only workaround
3304 * if end byte alignment not correct move us
3305 * into the next dword */
3306 if ((unsigned long)(skb->tail - 1) & 4)
3313 pull_size = min((unsigned int)4, skb->data_len);
3314 if (!__pskb_pull_tail(skb, pull_size)) {
3316 "__pskb_pull_tail failed.\n");
3317 dev_kfree_skb_any(skb);
3318 return NETDEV_TX_OK;
3320 len = skb->len - skb->data_len;
3329 /* reserve a descriptor for the offload context */
3330 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
3334 /* Controller Erratum workaround */
3335 if (!skb->data_len && tx_ring->last_tx_tso && !skb_is_gso(skb))
3338 count += TXD_USE_COUNT(len, max_txd_pwr);
3340 if (adapter->pcix_82544)
3343 /* work-around for errata 10 and it applies to all controllers
3344 * in PCI-X mode, so add one more descriptor to the count
3346 if (unlikely((adapter->hw.bus_type == e1000_bus_type_pcix) &&
3350 nr_frags = skb_shinfo(skb)->nr_frags;
3351 for (f = 0; f < nr_frags; f++)
3352 count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
3354 if (adapter->pcix_82544)
3358 if (adapter->hw.tx_pkt_filtering &&
3359 (adapter->hw.mac_type == e1000_82573))
3360 e1000_transfer_dhcp_info(adapter, skb);
3362 local_irq_save(flags);
3363 if (!spin_trylock(&tx_ring->tx_lock)) {
3364 /* Collision - tell upper layer to requeue */
3365 local_irq_restore(flags);
3366 return NETDEV_TX_LOCKED;
3369 /* need: count + 2 desc gap to keep tail from touching
3370 * head, otherwise try next time */
3371 if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2))) {
3372 spin_unlock_irqrestore(&tx_ring->tx_lock, flags);
3373 return NETDEV_TX_BUSY;
3376 if (unlikely(adapter->hw.mac_type == e1000_82547)) {
3377 if (unlikely(e1000_82547_fifo_workaround(adapter, skb))) {
3378 netif_stop_queue(netdev);
3379 mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1);
3380 spin_unlock_irqrestore(&tx_ring->tx_lock, flags);
3381 return NETDEV_TX_BUSY;
3385 if (unlikely(adapter->vlgrp && vlan_tx_tag_present(skb))) {
3386 tx_flags |= E1000_TX_FLAGS_VLAN;
3387 tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
3390 first = tx_ring->next_to_use;
3392 tso = e1000_tso(adapter, tx_ring, skb);
3394 dev_kfree_skb_any(skb);
3395 spin_unlock_irqrestore(&tx_ring->tx_lock, flags);
3396 return NETDEV_TX_OK;
3400 tx_ring->last_tx_tso = 1;
3401 tx_flags |= E1000_TX_FLAGS_TSO;
3402 } else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
3403 tx_flags |= E1000_TX_FLAGS_CSUM;
3405 /* Old method was to assume IPv4 packet by default if TSO was enabled.
3406 * 82571 hardware supports TSO capabilities for IPv6 as well...
3407 * no longer assume, we must. */
3408 if (likely(skb->protocol == htons(ETH_P_IP)))
3409 tx_flags |= E1000_TX_FLAGS_IPV4;
3411 e1000_tx_queue(adapter, tx_ring, tx_flags,
3412 e1000_tx_map(adapter, tx_ring, skb, first,
3413 max_per_txd, nr_frags, mss));
3415 netdev->trans_start = jiffies;
3417 /* Make sure there is space in the ring for the next send. */
3418 e1000_maybe_stop_tx(netdev, tx_ring, MAX_SKB_FRAGS + 2);
3420 spin_unlock_irqrestore(&tx_ring->tx_lock, flags);
3421 return NETDEV_TX_OK;
3425 * e1000_tx_timeout - Respond to a Tx Hang
3426 * @netdev: network interface device structure
3430 e1000_tx_timeout(struct net_device *netdev)
3432 struct e1000_adapter *adapter = netdev_priv(netdev);
3434 /* Do the reset outside of interrupt context */
3435 adapter->tx_timeout_count++;
3436 schedule_work(&adapter->reset_task);
3440 e1000_reset_task(struct work_struct *work)
3442 struct e1000_adapter *adapter =
3443 container_of(work, struct e1000_adapter, reset_task);
3445 e1000_reinit_locked(adapter);
3449 * e1000_get_stats - Get System Network Statistics
3450 * @netdev: network interface device structure
3452 * Returns the address of the device statistics structure.
3453 * The statistics are actually updated from the timer callback.
3456 static struct net_device_stats *
3457 e1000_get_stats(struct net_device *netdev)
3459 struct e1000_adapter *adapter = netdev_priv(netdev);
3461 /* only return the current stats */
3462 return &adapter->net_stats;
3466 * e1000_change_mtu - Change the Maximum Transfer Unit
3467 * @netdev: network interface device structure
3468 * @new_mtu: new value for maximum frame size
3470 * Returns 0 on success, negative on failure
3474 e1000_change_mtu(struct net_device *netdev, int new_mtu)
3476 struct e1000_adapter *adapter = netdev_priv(netdev);
3477 int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
3478 uint16_t eeprom_data = 0;
3480 if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
3481 (max_frame > MAX_JUMBO_FRAME_SIZE)) {
3482 DPRINTK(PROBE, ERR, "Invalid MTU setting\n");
3486 /* Adapter-specific max frame size limits. */
3487 switch (adapter->hw.mac_type) {
3488 case e1000_undefined ... e1000_82542_rev2_1:
3490 if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) {
3491 DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
3496 /* Jumbo Frames not supported if:
3497 * - this is not an 82573L device
3498 * - ASPM is enabled in any way (0x1A bits 3:2) */
3499 e1000_read_eeprom(&adapter->hw, EEPROM_INIT_3GIO_3, 1,
3501 if ((adapter->hw.device_id != E1000_DEV_ID_82573L) ||
3502 (eeprom_data & EEPROM_WORD1A_ASPM_MASK)) {
3503 if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) {
3505 "Jumbo Frames not supported.\n");
3510 /* ERT will be enabled later to enable wire speed receives */
3512 /* fall through to get support */
3515 case e1000_80003es2lan:
3516 #define MAX_STD_JUMBO_FRAME_SIZE 9234
3517 if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
3518 DPRINTK(PROBE, ERR, "MTU > 9216 not supported.\n");
3523 /* Capable of supporting up to MAX_JUMBO_FRAME_SIZE limit. */
3527 /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
3528 * means we reserve 2 more, this pushes us to allocate from the next
3530 * i.e. RXBUFFER_2048 --> size-4096 slab */
3532 if (max_frame <= E1000_RXBUFFER_256)
3533 adapter->rx_buffer_len = E1000_RXBUFFER_256;
3534 else if (max_frame <= E1000_RXBUFFER_512)
3535 adapter->rx_buffer_len = E1000_RXBUFFER_512;
3536 else if (max_frame <= E1000_RXBUFFER_1024)
3537 adapter->rx_buffer_len = E1000_RXBUFFER_1024;
3538 else if (max_frame <= E1000_RXBUFFER_2048)
3539 adapter->rx_buffer_len = E1000_RXBUFFER_2048;
3540 else if (max_frame <= E1000_RXBUFFER_4096)
3541 adapter->rx_buffer_len = E1000_RXBUFFER_4096;
3542 else if (max_frame <= E1000_RXBUFFER_8192)
3543 adapter->rx_buffer_len = E1000_RXBUFFER_8192;
3544 else if (max_frame <= E1000_RXBUFFER_16384)
3545 adapter->rx_buffer_len = E1000_RXBUFFER_16384;
3547 /* adjust allocation if LPE protects us, and we aren't using SBP */
3548 if (!adapter->hw.tbi_compatibility_on &&
3549 ((max_frame == MAXIMUM_ETHERNET_FRAME_SIZE) ||
3550 (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
3551 adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
3553 netdev->mtu = new_mtu;
3554 adapter->hw.max_frame_size = max_frame;
3556 if (netif_running(netdev))
3557 e1000_reinit_locked(adapter);
3563 * e1000_update_stats - Update the board statistics counters
3564 * @adapter: board private structure
3568 e1000_update_stats(struct e1000_adapter *adapter)
3570 struct e1000_hw *hw = &adapter->hw;
3571 struct pci_dev *pdev = adapter->pdev;
3572 unsigned long flags;
3575 #define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
3578 * Prevent stats update while adapter is being reset, or if the pci
3579 * connection is down.
3581 if (adapter->link_speed == 0)
3583 if (pci_channel_offline(pdev))
3586 spin_lock_irqsave(&adapter->stats_lock, flags);
3588 /* these counters are modified from e1000_adjust_tbi_stats,
3589 * called from the interrupt context, so they must only
3590 * be written while holding adapter->stats_lock
3593 adapter->stats.crcerrs += E1000_READ_REG(hw, CRCERRS);
3594 adapter->stats.gprc += E1000_READ_REG(hw, GPRC);
3595 adapter->stats.gorcl += E1000_READ_REG(hw, GORCL);
3596 adapter->stats.gorch += E1000_READ_REG(hw, GORCH);
3597 adapter->stats.bprc += E1000_READ_REG(hw, BPRC);
3598 adapter->stats.mprc += E1000_READ_REG(hw, MPRC);
3599 adapter->stats.roc += E1000_READ_REG(hw, ROC);
3601 if (adapter->hw.mac_type != e1000_ich8lan) {
3602 adapter->stats.prc64 += E1000_READ_REG(hw, PRC64);
3603 adapter->stats.prc127 += E1000_READ_REG(hw, PRC127);
3604 adapter->stats.prc255 += E1000_READ_REG(hw, PRC255);
3605 adapter->stats.prc511 += E1000_READ_REG(hw, PRC511);
3606 adapter->stats.prc1023 += E1000_READ_REG(hw, PRC1023);
3607 adapter->stats.prc1522 += E1000_READ_REG(hw, PRC1522);
3610 adapter->stats.symerrs += E1000_READ_REG(hw, SYMERRS);
3611 adapter->stats.mpc += E1000_READ_REG(hw, MPC);
3612 adapter->stats.scc += E1000_READ_REG(hw, SCC);
3613 adapter->stats.ecol += E1000_READ_REG(hw, ECOL);
3614 adapter->stats.mcc += E1000_READ_REG(hw, MCC);
3615 adapter->stats.latecol += E1000_READ_REG(hw, LATECOL);
3616 adapter->stats.dc += E1000_READ_REG(hw, DC);
3617 adapter->stats.sec += E1000_READ_REG(hw, SEC);
3618 adapter->stats.rlec += E1000_READ_REG(hw, RLEC);
3619 adapter->stats.xonrxc += E1000_READ_REG(hw, XONRXC);
3620 adapter->stats.xontxc += E1000_READ_REG(hw, XONTXC);
3621 adapter->stats.xoffrxc += E1000_READ_REG(hw, XOFFRXC);
3622 adapter->stats.xofftxc += E1000_READ_REG(hw, XOFFTXC);
3623 adapter->stats.fcruc += E1000_READ_REG(hw, FCRUC);
3624 adapter->stats.gptc += E1000_READ_REG(hw, GPTC);
3625 adapter->stats.gotcl += E1000_READ_REG(hw, GOTCL);
3626 adapter->stats.gotch += E1000_READ_REG(hw, GOTCH);
3627 adapter->stats.rnbc += E1000_READ_REG(hw, RNBC);
3628 adapter->stats.ruc += E1000_READ_REG(hw, RUC);
3629 adapter->stats.rfc += E1000_READ_REG(hw, RFC);
3630 adapter->stats.rjc += E1000_READ_REG(hw, RJC);
3631 adapter->stats.torl += E1000_READ_REG(hw, TORL);
3632 adapter->stats.torh += E1000_READ_REG(hw, TORH);
3633 adapter->stats.totl += E1000_READ_REG(hw, TOTL);
3634 adapter->stats.toth += E1000_READ_REG(hw, TOTH);
3635 adapter->stats.tpr += E1000_READ_REG(hw, TPR);
3637 if (adapter->hw.mac_type != e1000_ich8lan) {
3638 adapter->stats.ptc64 += E1000_READ_REG(hw, PTC64);
3639 adapter->stats.ptc127 += E1000_READ_REG(hw, PTC127);
3640 adapter->stats.ptc255 += E1000_READ_REG(hw, PTC255);
3641 adapter->stats.ptc511 += E1000_READ_REG(hw, PTC511);
3642 adapter->stats.ptc1023 += E1000_READ_REG(hw, PTC1023);
3643 adapter->stats.ptc1522 += E1000_READ_REG(hw, PTC1522);
3646 adapter->stats.mptc += E1000_READ_REG(hw, MPTC);
3647 adapter->stats.bptc += E1000_READ_REG(hw, BPTC);
3649 /* used for adaptive IFS */
3651 hw->tx_packet_delta = E1000_READ_REG(hw, TPT);
3652 adapter->stats.tpt += hw->tx_packet_delta;
3653 hw->collision_delta = E1000_READ_REG(hw, COLC);
3654 adapter->stats.colc += hw->collision_delta;
3656 if (hw->mac_type >= e1000_82543) {
3657 adapter->stats.algnerrc += E1000_READ_REG(hw, ALGNERRC);
3658 adapter->stats.rxerrc += E1000_READ_REG(hw, RXERRC);
3659 adapter->stats.tncrs += E1000_READ_REG(hw, TNCRS);
3660 adapter->stats.cexterr += E1000_READ_REG(hw, CEXTERR);
3661 adapter->stats.tsctc += E1000_READ_REG(hw, TSCTC);
3662 adapter->stats.tsctfc += E1000_READ_REG(hw, TSCTFC);
3664 if (hw->mac_type > e1000_82547_rev_2) {
3665 adapter->stats.iac += E1000_READ_REG(hw, IAC);
3666 adapter->stats.icrxoc += E1000_READ_REG(hw, ICRXOC);
3668 if (adapter->hw.mac_type != e1000_ich8lan) {
3669 adapter->stats.icrxptc += E1000_READ_REG(hw, ICRXPTC);
3670 adapter->stats.icrxatc += E1000_READ_REG(hw, ICRXATC);
3671 adapter->stats.ictxptc += E1000_READ_REG(hw, ICTXPTC);
3672 adapter->stats.ictxatc += E1000_READ_REG(hw, ICTXATC);
3673 adapter->stats.ictxqec += E1000_READ_REG(hw, ICTXQEC);
3674 adapter->stats.ictxqmtc += E1000_READ_REG(hw, ICTXQMTC);
3675 adapter->stats.icrxdmtc += E1000_READ_REG(hw, ICRXDMTC);
3679 /* Fill out the OS statistics structure */
3680 adapter->net_stats.rx_packets = adapter->stats.gprc;
3681 adapter->net_stats.tx_packets = adapter->stats.gptc;
3682 adapter->net_stats.rx_bytes = adapter->stats.gorcl;
3683 adapter->net_stats.tx_bytes = adapter->stats.gotcl;
3684 adapter->net_stats.multicast = adapter->stats.mprc;
3685 adapter->net_stats.collisions = adapter->stats.colc;
3689 /* RLEC on some newer hardware can be incorrect so build
3690 * our own version based on RUC and ROC */
3691 adapter->net_stats.rx_errors = adapter->stats.rxerrc +
3692 adapter->stats.crcerrs + adapter->stats.algnerrc +
3693 adapter->stats.ruc + adapter->stats.roc +
3694 adapter->stats.cexterr;
3695 adapter->stats.rlerrc = adapter->stats.ruc + adapter->stats.roc;
3696 adapter->net_stats.rx_length_errors = adapter->stats.rlerrc;
3697 adapter->net_stats.rx_crc_errors = adapter->stats.crcerrs;
3698 adapter->net_stats.rx_frame_errors = adapter->stats.algnerrc;
3699 adapter->net_stats.rx_missed_errors = adapter->stats.mpc;
3702 adapter->stats.txerrc = adapter->stats.ecol + adapter->stats.latecol;
3703 adapter->net_stats.tx_errors = adapter->stats.txerrc;
3704 adapter->net_stats.tx_aborted_errors = adapter->stats.ecol;
3705 adapter->net_stats.tx_window_errors = adapter->stats.latecol;
3706 adapter->net_stats.tx_carrier_errors = adapter->stats.tncrs;
3707 if (adapter->hw.bad_tx_carr_stats_fd &&
3708 adapter->link_duplex == FULL_DUPLEX) {
3709 adapter->net_stats.tx_carrier_errors = 0;
3710 adapter->stats.tncrs = 0;
3713 /* Tx Dropped needs to be maintained elsewhere */
3716 if (hw->media_type == e1000_media_type_copper) {
3717 if ((adapter->link_speed == SPEED_1000) &&
3718 (!e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_tmp))) {
3719 phy_tmp &= PHY_IDLE_ERROR_COUNT_MASK;
3720 adapter->phy_stats.idle_errors += phy_tmp;
3723 if ((hw->mac_type <= e1000_82546) &&
3724 (hw->phy_type == e1000_phy_m88) &&
3725 !e1000_read_phy_reg(hw, M88E1000_RX_ERR_CNTR, &phy_tmp))
3726 adapter->phy_stats.receive_errors += phy_tmp;
3729 /* Management Stats */
3730 if (adapter->hw.has_smbus) {
3731 adapter->stats.mgptc += E1000_READ_REG(hw, MGTPTC);
3732 adapter->stats.mgprc += E1000_READ_REG(hw, MGTPRC);
3733 adapter->stats.mgpdc += E1000_READ_REG(hw, MGTPDC);
3736 spin_unlock_irqrestore(&adapter->stats_lock, flags);
3738 #ifdef CONFIG_PCI_MSI
3741 * e1000_intr_msi - Interrupt Handler
3742 * @irq: interrupt number
3743 * @data: pointer to a network interface device structure
3747 e1000_intr_msi(int irq, void *data)
3749 struct net_device *netdev = data;
3750 struct e1000_adapter *adapter = netdev_priv(netdev);
3751 struct e1000_hw *hw = &adapter->hw;
3752 #ifndef CONFIG_E1000_NAPI
3755 uint32_t icr = E1000_READ_REG(hw, ICR);
3757 #ifdef CONFIG_E1000_NAPI
3758 /* read ICR disables interrupts using IAM, so keep up with our
3759 * enable/disable accounting */
3760 atomic_inc(&adapter->irq_sem);
3762 if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
3763 hw->get_link_status = 1;
3764 /* 80003ES2LAN workaround-- For packet buffer work-around on
3765 * link down event; disable receives here in the ISR and reset
3766 * adapter in watchdog */
3767 if (netif_carrier_ok(netdev) &&
3768 (adapter->hw.mac_type == e1000_80003es2lan)) {
3769 /* disable receives */
3770 uint32_t rctl = E1000_READ_REG(hw, RCTL);
3771 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
3773 /* guard against interrupt when we're going down */
3774 if (!test_bit(__E1000_DOWN, &adapter->flags))
3775 mod_timer(&adapter->watchdog_timer, jiffies + 1);
3778 #ifdef CONFIG_E1000_NAPI
3779 if (likely(netif_rx_schedule_prep(netdev))) {
3780 adapter->total_tx_bytes = 0;
3781 adapter->total_tx_packets = 0;
3782 adapter->total_rx_bytes = 0;
3783 adapter->total_rx_packets = 0;
3784 __netif_rx_schedule(netdev);
3786 e1000_irq_enable(adapter);
3788 adapter->total_tx_bytes = 0;
3789 adapter->total_rx_bytes = 0;
3790 adapter->total_tx_packets = 0;
3791 adapter->total_rx_packets = 0;
3793 for (i = 0; i < E1000_MAX_INTR; i++)
3794 if (unlikely(!adapter->clean_rx(adapter, adapter->rx_ring) &
3795 !e1000_clean_tx_irq(adapter, adapter->tx_ring)))
3798 if (likely(adapter->itr_setting & 3))
3799 e1000_set_itr(adapter);
3807 * e1000_intr - Interrupt Handler
3808 * @irq: interrupt number
3809 * @data: pointer to a network interface device structure
3813 e1000_intr(int irq, void *data)
3815 struct net_device *netdev = data;
3816 struct e1000_adapter *adapter = netdev_priv(netdev);
3817 struct e1000_hw *hw = &adapter->hw;
3818 uint32_t rctl, icr = E1000_READ_REG(hw, ICR);
3819 #ifndef CONFIG_E1000_NAPI
3823 return IRQ_NONE; /* Not our interrupt */
3825 #ifdef CONFIG_E1000_NAPI
3826 /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is
3827 * not set, then the adapter didn't send an interrupt */
3828 if (unlikely(hw->mac_type >= e1000_82571 &&
3829 !(icr & E1000_ICR_INT_ASSERTED)))
3832 /* Interrupt Auto-Mask...upon reading ICR,
3833 * interrupts are masked. No need for the
3834 * IMC write, but it does mean we should
3835 * account for it ASAP. */
3836 if (likely(hw->mac_type >= e1000_82571))
3837 atomic_inc(&adapter->irq_sem);
3840 if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) {
3841 hw->get_link_status = 1;
3842 /* 80003ES2LAN workaround--
3843 * For packet buffer work-around on link down event;
3844 * disable receives here in the ISR and
3845 * reset adapter in watchdog
3847 if (netif_carrier_ok(netdev) &&
3848 (adapter->hw.mac_type == e1000_80003es2lan)) {
3849 /* disable receives */
3850 rctl = E1000_READ_REG(hw, RCTL);
3851 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
3853 /* guard against interrupt when we're going down */
3854 if (!test_bit(__E1000_DOWN, &adapter->flags))
3855 mod_timer(&adapter->watchdog_timer, jiffies + 1);
3858 #ifdef CONFIG_E1000_NAPI
3859 if (unlikely(hw->mac_type < e1000_82571)) {
3860 /* disable interrupts, without the synchronize_irq bit */
3861 atomic_inc(&adapter->irq_sem);
3862 E1000_WRITE_REG(hw, IMC, ~0);
3863 E1000_WRITE_FLUSH(hw);
3865 if (likely(netif_rx_schedule_prep(netdev))) {
3866 adapter->total_tx_bytes = 0;
3867 adapter->total_tx_packets = 0;
3868 adapter->total_rx_bytes = 0;
3869 adapter->total_rx_packets = 0;
3870 __netif_rx_schedule(netdev);
3872 /* this really should not happen! if it does it is basically a
3873 * bug, but not a hard error, so enable ints and continue */
3874 e1000_irq_enable(adapter);
3876 /* Writing IMC and IMS is needed for 82547.
3877 * Due to Hub Link bus being occupied, an interrupt
3878 * de-assertion message is not able to be sent.
3879 * When an interrupt assertion message is generated later,
3880 * two messages are re-ordered and sent out.
3881 * That causes APIC to think 82547 is in de-assertion
3882 * state, while 82547 is in assertion state, resulting
3883 * in dead lock. Writing IMC forces 82547 into
3884 * de-assertion state.
3886 if (hw->mac_type == e1000_82547 || hw->mac_type == e1000_82547_rev_2) {
3887 atomic_inc(&adapter->irq_sem);
3888 E1000_WRITE_REG(hw, IMC, ~0);
3891 adapter->total_tx_bytes = 0;
3892 adapter->total_rx_bytes = 0;
3893 adapter->total_tx_packets = 0;
3894 adapter->total_rx_packets = 0;
3896 for (i = 0; i < E1000_MAX_INTR; i++)
3897 if (unlikely(!adapter->clean_rx(adapter, adapter->rx_ring) &
3898 !e1000_clean_tx_irq(adapter, adapter->tx_ring)))
3901 if (likely(adapter->itr_setting & 3))
3902 e1000_set_itr(adapter);
3904 if (hw->mac_type == e1000_82547 || hw->mac_type == e1000_82547_rev_2)
3905 e1000_irq_enable(adapter);
3911 #ifdef CONFIG_E1000_NAPI
3913 * e1000_clean - NAPI Rx polling callback
3914 * @adapter: board private structure
3918 e1000_clean(struct net_device *poll_dev, int *budget)
3920 struct e1000_adapter *adapter;
3921 int work_to_do = min(*budget, poll_dev->quota);
3922 int tx_cleaned = 0, work_done = 0;
3924 /* Must NOT use netdev_priv macro here. */
3925 adapter = poll_dev->priv;
3927 /* Keep link state information with original netdev */
3928 if (!netif_carrier_ok(poll_dev))
3931 /* e1000_clean is called per-cpu. This lock protects
3932 * tx_ring[0] from being cleaned by multiple cpus
3933 * simultaneously. A failure obtaining the lock means
3934 * tx_ring[0] is currently being cleaned anyway. */
3935 if (spin_trylock(&adapter->tx_queue_lock)) {
3936 tx_cleaned = e1000_clean_tx_irq(adapter,
3937 &adapter->tx_ring[0]);
3938 spin_unlock(&adapter->tx_queue_lock);
3941 adapter->clean_rx(adapter, &adapter->rx_ring[0],
3942 &work_done, work_to_do);
3944 *budget -= work_done;
3945 poll_dev->quota -= work_done;
3947 /* If no Tx and not enough Rx work done, exit the polling mode */
3948 if ((!tx_cleaned && (work_done == 0)) ||
3949 !netif_running(poll_dev)) {
3951 if (likely(adapter->itr_setting & 3))
3952 e1000_set_itr(adapter);
3953 netif_rx_complete(poll_dev);
3954 e1000_irq_enable(adapter);
3963 * e1000_clean_tx_irq - Reclaim resources after transmit completes
3964 * @adapter: board private structure
3968 e1000_clean_tx_irq(struct e1000_adapter *adapter,
3969 struct e1000_tx_ring *tx_ring)
3971 struct net_device *netdev = adapter->netdev;
3972 struct e1000_tx_desc *tx_desc, *eop_desc;
3973 struct e1000_buffer *buffer_info;
3974 unsigned int i, eop;
3975 #ifdef CONFIG_E1000_NAPI
3976 unsigned int count = 0;
3978 boolean_t cleaned = FALSE;
3979 unsigned int total_tx_bytes=0, total_tx_packets=0;
3981 i = tx_ring->next_to_clean;
3982 eop = tx_ring->buffer_info[i].next_to_watch;
3983 eop_desc = E1000_TX_DESC(*tx_ring, eop);
3985 while (eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) {
3986 for (cleaned = FALSE; !cleaned; ) {
3987 tx_desc = E1000_TX_DESC(*tx_ring, i);
3988 buffer_info = &tx_ring->buffer_info[i];
3989 cleaned = (i == eop);
3992 struct sk_buff *skb = buffer_info->skb;
3993 unsigned int segs, bytecount;
3994 segs = skb_shinfo(skb)->gso_segs ?: 1;
3995 /* multiply data chunks by size of headers */
3996 bytecount = ((segs - 1) * skb_headlen(skb)) +
3998 total_tx_packets += segs;
3999 total_tx_bytes += bytecount;
4001 e1000_unmap_and_free_tx_resource(adapter, buffer_info);
4002 tx_desc->upper.data = 0;
4004 if (unlikely(++i == tx_ring->count)) i = 0;
4007 eop = tx_ring->buffer_info[i].next_to_watch;
4008 eop_desc = E1000_TX_DESC(*tx_ring, eop);
4009 #ifdef CONFIG_E1000_NAPI
4010 #define E1000_TX_WEIGHT 64
4011 /* weight of a sort for tx, to avoid endless transmit cleanup */
4012 if (count++ == E1000_TX_WEIGHT) break;
4016 tx_ring->next_to_clean = i;
4018 #define TX_WAKE_THRESHOLD 32
4019 if (unlikely(cleaned && netif_carrier_ok(netdev) &&
4020 E1000_DESC_UNUSED(tx_ring) >= TX_WAKE_THRESHOLD)) {
4021 /* Make sure that anybody stopping the queue after this
4022 * sees the new next_to_clean.
4025 if (netif_queue_stopped(netdev)) {
4026 netif_wake_queue(netdev);
4027 ++adapter->restart_queue;
4031 if (adapter->detect_tx_hung) {
4032 /* Detect a transmit hang in hardware, this serializes the
4033 * check with the clearing of time_stamp and movement of i */
4034 adapter->detect_tx_hung = FALSE;
4035 if (tx_ring->buffer_info[eop].dma &&
4036 time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
4037 (adapter->tx_timeout_factor * HZ))
4038 && !(E1000_READ_REG(&adapter->hw, STATUS) &
4039 E1000_STATUS_TXOFF)) {
4041 /* detected Tx unit hang */
4042 DPRINTK(DRV, ERR, "Detected Tx Unit Hang\n"
4046 " next_to_use <%x>\n"
4047 " next_to_clean <%x>\n"
4048 "buffer_info[next_to_clean]\n"
4049 " time_stamp <%lx>\n"
4050 " next_to_watch <%x>\n"
4052 " next_to_watch.status <%x>\n",
4053 (unsigned long)((tx_ring - adapter->tx_ring) /
4054 sizeof(struct e1000_tx_ring)),
4055 readl(adapter->hw.hw_addr + tx_ring->tdh),
4056 readl(adapter->hw.hw_addr + tx_ring->tdt),
4057 tx_ring->next_to_use,
4058 tx_ring->next_to_clean,
4059 tx_ring->buffer_info[eop].time_stamp,
4062 eop_desc->upper.fields.status);
4063 netif_stop_queue(netdev);
4066 adapter->total_tx_bytes += total_tx_bytes;
4067 adapter->total_tx_packets += total_tx_packets;
4072 * e1000_rx_checksum - Receive Checksum Offload for 82543
4073 * @adapter: board private structure
4074 * @status_err: receive descriptor status and error fields
4075 * @csum: receive descriptor csum field
4076 * @sk_buff: socket buffer with received data
4080 e1000_rx_checksum(struct e1000_adapter *adapter,
4081 uint32_t status_err, uint32_t csum,
4082 struct sk_buff *skb)
4084 uint16_t status = (uint16_t)status_err;
4085 uint8_t errors = (uint8_t)(status_err >> 24);
4086 skb->ip_summed = CHECKSUM_NONE;
4088 /* 82543 or newer only */
4089 if (unlikely(adapter->hw.mac_type < e1000_82543)) return;
4090 /* Ignore Checksum bit is set */
4091 if (unlikely(status & E1000_RXD_STAT_IXSM)) return;
4092 /* TCP/UDP checksum error bit is set */
4093 if (unlikely(errors & E1000_RXD_ERR_TCPE)) {
4094 /* let the stack verify checksum errors */
4095 adapter->hw_csum_err++;
4098 /* TCP/UDP Checksum has not been calculated */
4099 if (adapter->hw.mac_type <= e1000_82547_rev_2) {
4100 if (!(status & E1000_RXD_STAT_TCPCS))
4103 if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
4106 /* It must be a TCP or UDP packet with a valid checksum */
4107 if (likely(status & E1000_RXD_STAT_TCPCS)) {
4108 /* TCP checksum is good */
4109 skb->ip_summed = CHECKSUM_UNNECESSARY;
4110 } else if (adapter->hw.mac_type > e1000_82547_rev_2) {
4111 /* IP fragment with UDP payload */
4112 /* Hardware complements the payload checksum, so we undo it
4113 * and then put the value in host order for further stack use.
4115 csum = ntohl(csum ^ 0xFFFF);
4117 skb->ip_summed = CHECKSUM_COMPLETE;
4119 adapter->hw_csum_good++;
4123 * e1000_clean_rx_irq - Send received data up the network stack; legacy
4124 * @adapter: board private structure
4128 #ifdef CONFIG_E1000_NAPI
4129 e1000_clean_rx_irq(struct e1000_adapter *adapter,
4130 struct e1000_rx_ring *rx_ring,
4131 int *work_done, int work_to_do)
4133 e1000_clean_rx_irq(struct e1000_adapter *adapter,
4134 struct e1000_rx_ring *rx_ring)
4137 struct net_device *netdev = adapter->netdev;
4138 struct pci_dev *pdev = adapter->pdev;
4139 struct e1000_rx_desc *rx_desc, *next_rxd;
4140 struct e1000_buffer *buffer_info, *next_buffer;
4141 unsigned long flags;
4145 int cleaned_count = 0;
4146 boolean_t cleaned = FALSE;
4147 unsigned int total_rx_bytes=0, total_rx_packets=0;
4149 i = rx_ring->next_to_clean;
4150 rx_desc = E1000_RX_DESC(*rx_ring, i);
4151 buffer_info = &rx_ring->buffer_info[i];
4153 while (rx_desc->status & E1000_RXD_STAT_DD) {
4154 struct sk_buff *skb;
4157 #ifdef CONFIG_E1000_NAPI
4158 if (*work_done >= work_to_do)
4162 status = rx_desc->status;
4163 skb = buffer_info->skb;
4164 buffer_info->skb = NULL;
4166 prefetch(skb->data - NET_IP_ALIGN);
4168 if (++i == rx_ring->count) i = 0;
4169 next_rxd = E1000_RX_DESC(*rx_ring, i);
4172 next_buffer = &rx_ring->buffer_info[i];
4176 pci_unmap_single(pdev,
4178 buffer_info->length,
4179 PCI_DMA_FROMDEVICE);
4181 length = le16_to_cpu(rx_desc->length);
4183 if (unlikely(!(status & E1000_RXD_STAT_EOP))) {
4184 /* All receives must fit into a single buffer */
4185 E1000_DBG("%s: Receive packet consumed multiple"
4186 " buffers\n", netdev->name);
4188 buffer_info->skb = skb;
4192 if (unlikely(rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK)) {
4193 last_byte = *(skb->data + length - 1);
4194 if (TBI_ACCEPT(&adapter->hw, status,
4195 rx_desc->errors, length, last_byte)) {
4196 spin_lock_irqsave(&adapter->stats_lock, flags);
4197 e1000_tbi_adjust_stats(&adapter->hw,
4200 spin_unlock_irqrestore(&adapter->stats_lock,
4205 buffer_info->skb = skb;
4210 /* adjust length to remove Ethernet CRC, this must be
4211 * done after the TBI_ACCEPT workaround above */
4214 /* probably a little skewed due to removing CRC */
4215 total_rx_bytes += length;
4218 /* code added for copybreak, this should improve
4219 * performance for small packets with large amounts
4220 * of reassembly being done in the stack */
4221 if (length < copybreak) {
4222 struct sk_buff *new_skb =
4223 netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
4225 skb_reserve(new_skb, NET_IP_ALIGN);
4226 memcpy(new_skb->data - NET_IP_ALIGN,
4227 skb->data - NET_IP_ALIGN,
4228 length + NET_IP_ALIGN);
4229 /* save the skb in buffer_info as good */
4230 buffer_info->skb = skb;
4233 /* else just continue with the old one */
4235 /* end copybreak code */
4236 skb_put(skb, length);
4238 /* Receive Checksum Offload */
4239 e1000_rx_checksum(adapter,
4240 (uint32_t)(status) |
4241 ((uint32_t)(rx_desc->errors) << 24),
4242 le16_to_cpu(rx_desc->csum), skb);
4244 skb->protocol = eth_type_trans(skb, netdev);
4245 #ifdef CONFIG_E1000_NAPI
4246 if (unlikely(adapter->vlgrp &&
4247 (status & E1000_RXD_STAT_VP))) {
4248 vlan_hwaccel_receive_skb(skb, adapter->vlgrp,
4249 le16_to_cpu(rx_desc->special) &
4250 E1000_RXD_SPC_VLAN_MASK);
4252 netif_receive_skb(skb);
4254 #else /* CONFIG_E1000_NAPI */
4255 if (unlikely(adapter->vlgrp &&
4256 (status & E1000_RXD_STAT_VP))) {
4257 vlan_hwaccel_rx(skb, adapter->vlgrp,
4258 le16_to_cpu(rx_desc->special) &
4259 E1000_RXD_SPC_VLAN_MASK);
4263 #endif /* CONFIG_E1000_NAPI */
4264 netdev->last_rx = jiffies;
4267 rx_desc->status = 0;
4269 /* return some buffers to hardware, one at a time is too slow */
4270 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
4271 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4275 /* use prefetched values */
4277 buffer_info = next_buffer;
4279 rx_ring->next_to_clean = i;
4281 cleaned_count = E1000_DESC_UNUSED(rx_ring);
4283 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4285 adapter->total_rx_packets += total_rx_packets;
4286 adapter->total_rx_bytes += total_rx_bytes;
4291 * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split
4292 * @adapter: board private structure
4296 #ifdef CONFIG_E1000_NAPI
4297 e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
4298 struct e1000_rx_ring *rx_ring,
4299 int *work_done, int work_to_do)
4301 e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
4302 struct e1000_rx_ring *rx_ring)
4305 union e1000_rx_desc_packet_split *rx_desc, *next_rxd;
4306 struct net_device *netdev = adapter->netdev;
4307 struct pci_dev *pdev = adapter->pdev;
4308 struct e1000_buffer *buffer_info, *next_buffer;
4309 struct e1000_ps_page *ps_page;
4310 struct e1000_ps_page_dma *ps_page_dma;
4311 struct sk_buff *skb;
4313 uint32_t length, staterr;
4314 int cleaned_count = 0;
4315 boolean_t cleaned = FALSE;
4316 unsigned int total_rx_bytes=0, total_rx_packets=0;
4318 i = rx_ring->next_to_clean;
4319 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
4320 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
4321 buffer_info = &rx_ring->buffer_info[i];
4323 while (staterr & E1000_RXD_STAT_DD) {
4324 ps_page = &rx_ring->ps_page[i];
4325 ps_page_dma = &rx_ring->ps_page_dma[i];
4326 #ifdef CONFIG_E1000_NAPI
4327 if (unlikely(*work_done >= work_to_do))
4331 skb = buffer_info->skb;
4333 /* in the packet split case this is header only */
4334 prefetch(skb->data - NET_IP_ALIGN);
4336 if (++i == rx_ring->count) i = 0;
4337 next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
4340 next_buffer = &rx_ring->buffer_info[i];
4344 pci_unmap_single(pdev, buffer_info->dma,
4345 buffer_info->length,
4346 PCI_DMA_FROMDEVICE);
4348 if (unlikely(!(staterr & E1000_RXD_STAT_EOP))) {
4349 E1000_DBG("%s: Packet Split buffers didn't pick up"
4350 " the full packet\n", netdev->name);
4351 dev_kfree_skb_irq(skb);
4355 if (unlikely(staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK)) {
4356 dev_kfree_skb_irq(skb);
4360 length = le16_to_cpu(rx_desc->wb.middle.length0);
4362 if (unlikely(!length)) {
4363 E1000_DBG("%s: Last part of the packet spanning"
4364 " multiple descriptors\n", netdev->name);
4365 dev_kfree_skb_irq(skb);
4370 skb_put(skb, length);
4373 /* this looks ugly, but it seems compiler issues make it
4374 more efficient than reusing j */
4375 int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
4377 /* page alloc/put takes too long and effects small packet
4378 * throughput, so unsplit small packets and save the alloc/put*/
4379 if (l1 && (l1 <= copybreak) && ((length + l1) <= adapter->rx_ps_bsize0)) {
4381 /* there is no documentation about how to call
4382 * kmap_atomic, so we can't hold the mapping
4384 pci_dma_sync_single_for_cpu(pdev,
4385 ps_page_dma->ps_page_dma[0],
4387 PCI_DMA_FROMDEVICE);
4388 vaddr = kmap_atomic(ps_page->ps_page[0],
4389 KM_SKB_DATA_SOFTIRQ);
4390 memcpy(skb->tail, vaddr, l1);
4391 kunmap_atomic(vaddr, KM_SKB_DATA_SOFTIRQ);
4392 pci_dma_sync_single_for_device(pdev,
4393 ps_page_dma->ps_page_dma[0],
4394 PAGE_SIZE, PCI_DMA_FROMDEVICE);
4395 /* remove the CRC */
4402 for (j = 0; j < adapter->rx_ps_pages; j++) {
4403 if (!(length= le16_to_cpu(rx_desc->wb.upper.length[j])))
4405 pci_unmap_page(pdev, ps_page_dma->ps_page_dma[j],
4406 PAGE_SIZE, PCI_DMA_FROMDEVICE);
4407 ps_page_dma->ps_page_dma[j] = 0;
4408 skb_fill_page_desc(skb, j, ps_page->ps_page[j], 0,
4410 ps_page->ps_page[j] = NULL;
4412 skb->data_len += length;
4413 skb->truesize += length;
4416 /* strip the ethernet crc, problem is we're using pages now so
4417 * this whole operation can get a little cpu intensive */
4418 pskb_trim(skb, skb->len - 4);
4421 total_rx_bytes += skb->len;
4424 e1000_rx_checksum(adapter, staterr,
4425 le16_to_cpu(rx_desc->wb.lower.hi_dword.csum_ip.csum), skb);
4426 skb->protocol = eth_type_trans(skb, netdev);
4428 if (likely(rx_desc->wb.upper.header_status &
4429 cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP)))
4430 adapter->rx_hdr_split++;
4431 #ifdef CONFIG_E1000_NAPI
4432 if (unlikely(adapter->vlgrp && (staterr & E1000_RXD_STAT_VP))) {
4433 vlan_hwaccel_receive_skb(skb, adapter->vlgrp,
4434 le16_to_cpu(rx_desc->wb.middle.vlan) &
4435 E1000_RXD_SPC_VLAN_MASK);
4437 netif_receive_skb(skb);
4439 #else /* CONFIG_E1000_NAPI */
4440 if (unlikely(adapter->vlgrp && (staterr & E1000_RXD_STAT_VP))) {
4441 vlan_hwaccel_rx(skb, adapter->vlgrp,
4442 le16_to_cpu(rx_desc->wb.middle.vlan) &
4443 E1000_RXD_SPC_VLAN_MASK);
4447 #endif /* CONFIG_E1000_NAPI */
4448 netdev->last_rx = jiffies;
4451 rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
4452 buffer_info->skb = NULL;
4454 /* return some buffers to hardware, one at a time is too slow */
4455 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
4456 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4460 /* use prefetched values */
4462 buffer_info = next_buffer;
4464 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
4466 rx_ring->next_to_clean = i;
4468 cleaned_count = E1000_DESC_UNUSED(rx_ring);
4470 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4472 adapter->total_rx_packets += total_rx_packets;
4473 adapter->total_rx_bytes += total_rx_bytes;
4478 * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
4479 * @adapter: address of board private structure
4483 e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
4484 struct e1000_rx_ring *rx_ring,
4487 struct net_device *netdev = adapter->netdev;
4488 struct pci_dev *pdev = adapter->pdev;
4489 struct e1000_rx_desc *rx_desc;
4490 struct e1000_buffer *buffer_info;
4491 struct sk_buff *skb;
4493 unsigned int bufsz = adapter->rx_buffer_len + NET_IP_ALIGN;
4495 i = rx_ring->next_to_use;
4496 buffer_info = &rx_ring->buffer_info[i];
4498 while (cleaned_count--) {
4499 skb = buffer_info->skb;
4505 skb = netdev_alloc_skb(netdev, bufsz);
4506 if (unlikely(!skb)) {
4507 /* Better luck next round */
4508 adapter->alloc_rx_buff_failed++;
4512 /* Fix for errata 23, can't cross 64kB boundary */
4513 if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
4514 struct sk_buff *oldskb = skb;
4515 DPRINTK(RX_ERR, ERR, "skb align check failed: %u bytes "
4516 "at %p\n", bufsz, skb->data);
4517 /* Try again, without freeing the previous */
4518 skb = netdev_alloc_skb(netdev, bufsz);
4519 /* Failed allocation, critical failure */
4521 dev_kfree_skb(oldskb);
4525 if (!e1000_check_64k_bound(adapter, skb->data, bufsz)) {
4528 dev_kfree_skb(oldskb);
4529 break; /* while !buffer_info->skb */
4532 /* Use new allocation */
4533 dev_kfree_skb(oldskb);
4535 /* Make buffer alignment 2 beyond a 16 byte boundary
4536 * this will result in a 16 byte aligned IP header after
4537 * the 14 byte MAC header is removed
4539 skb_reserve(skb, NET_IP_ALIGN);
4541 buffer_info->skb = skb;
4542 buffer_info->length = adapter->rx_buffer_len;
4544 buffer_info->dma = pci_map_single(pdev,
4546 adapter->rx_buffer_len,
4547 PCI_DMA_FROMDEVICE);
4549 /* Fix for errata 23, can't cross 64kB boundary */
4550 if (!e1000_check_64k_bound(adapter,
4551 (void *)(unsigned long)buffer_info->dma,
4552 adapter->rx_buffer_len)) {
4553 DPRINTK(RX_ERR, ERR,
4554 "dma align check failed: %u bytes at %p\n",
4555 adapter->rx_buffer_len,
4556 (void *)(unsigned long)buffer_info->dma);
4558 buffer_info->skb = NULL;
4560 pci_unmap_single(pdev, buffer_info->dma,
4561 adapter->rx_buffer_len,
4562 PCI_DMA_FROMDEVICE);
4564 break; /* while !buffer_info->skb */
4566 rx_desc = E1000_RX_DESC(*rx_ring, i);
4567 rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
4569 if (unlikely(++i == rx_ring->count))
4571 buffer_info = &rx_ring->buffer_info[i];
4574 if (likely(rx_ring->next_to_use != i)) {
4575 rx_ring->next_to_use = i;
4576 if (unlikely(i-- == 0))
4577 i = (rx_ring->count - 1);
4579 /* Force memory writes to complete before letting h/w
4580 * know there are new descriptors to fetch. (Only
4581 * applicable for weak-ordered memory model archs,
4582 * such as IA-64). */
4584 writel(i, adapter->hw.hw_addr + rx_ring->rdt);
4589 * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split
4590 * @adapter: address of board private structure
4594 e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
4595 struct e1000_rx_ring *rx_ring,
4598 struct net_device *netdev = adapter->netdev;
4599 struct pci_dev *pdev = adapter->pdev;
4600 union e1000_rx_desc_packet_split *rx_desc;
4601 struct e1000_buffer *buffer_info;
4602 struct e1000_ps_page *ps_page;
4603 struct e1000_ps_page_dma *ps_page_dma;
4604 struct sk_buff *skb;
4607 i = rx_ring->next_to_use;
4608 buffer_info = &rx_ring->buffer_info[i];
4609 ps_page = &rx_ring->ps_page[i];
4610 ps_page_dma = &rx_ring->ps_page_dma[i];
4612 while (cleaned_count--) {
4613 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
4615 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
4616 if (j < adapter->rx_ps_pages) {
4617 if (likely(!ps_page->ps_page[j])) {
4618 ps_page->ps_page[j] =
4619 alloc_page(GFP_ATOMIC);
4620 if (unlikely(!ps_page->ps_page[j])) {
4621 adapter->alloc_rx_buff_failed++;
4624 ps_page_dma->ps_page_dma[j] =
4626 ps_page->ps_page[j],
4628 PCI_DMA_FROMDEVICE);
4630 /* Refresh the desc even if buffer_addrs didn't
4631 * change because each write-back erases
4634 rx_desc->read.buffer_addr[j+1] =
4635 cpu_to_le64(ps_page_dma->ps_page_dma[j]);
4637 rx_desc->read.buffer_addr[j+1] = ~0;
4640 skb = netdev_alloc_skb(netdev,
4641 adapter->rx_ps_bsize0 + NET_IP_ALIGN);
4643 if (unlikely(!skb)) {
4644 adapter->alloc_rx_buff_failed++;
4648 /* Make buffer alignment 2 beyond a 16 byte boundary
4649 * this will result in a 16 byte aligned IP header after
4650 * the 14 byte MAC header is removed
4652 skb_reserve(skb, NET_IP_ALIGN);
4654 buffer_info->skb = skb;
4655 buffer_info->length = adapter->rx_ps_bsize0;
4656 buffer_info->dma = pci_map_single(pdev, skb->data,
4657 adapter->rx_ps_bsize0,
4658 PCI_DMA_FROMDEVICE);
4660 rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma);
4662 if (unlikely(++i == rx_ring->count)) i = 0;
4663 buffer_info = &rx_ring->buffer_info[i];
4664 ps_page = &rx_ring->ps_page[i];
4665 ps_page_dma = &rx_ring->ps_page_dma[i];
4669 if (likely(rx_ring->next_to_use != i)) {
4670 rx_ring->next_to_use = i;
4671 if (unlikely(i-- == 0)) i = (rx_ring->count - 1);
4673 /* Force memory writes to complete before letting h/w
4674 * know there are new descriptors to fetch. (Only
4675 * applicable for weak-ordered memory model archs,
4676 * such as IA-64). */
4678 /* Hardware increments by 16 bytes, but packet split
4679 * descriptors are 32 bytes...so we increment tail
4682 writel(i<<1, adapter->hw.hw_addr + rx_ring->rdt);
4687 * e1000_smartspeed - Workaround for SmartSpeed on 82541 and 82547 controllers.
4692 e1000_smartspeed(struct e1000_adapter *adapter)
4694 uint16_t phy_status;
4697 if ((adapter->hw.phy_type != e1000_phy_igp) || !adapter->hw.autoneg ||
4698 !(adapter->hw.autoneg_advertised & ADVERTISE_1000_FULL))
4701 if (adapter->smartspeed == 0) {
4702 /* If Master/Slave config fault is asserted twice,
4703 * we assume back-to-back */
4704 e1000_read_phy_reg(&adapter->hw, PHY_1000T_STATUS, &phy_status);
4705 if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
4706 e1000_read_phy_reg(&adapter->hw, PHY_1000T_STATUS, &phy_status);
4707 if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
4708 e1000_read_phy_reg(&adapter->hw, PHY_1000T_CTRL, &phy_ctrl);
4709 if (phy_ctrl & CR_1000T_MS_ENABLE) {
4710 phy_ctrl &= ~CR_1000T_MS_ENABLE;
4711 e1000_write_phy_reg(&adapter->hw, PHY_1000T_CTRL,
4713 adapter->smartspeed++;
4714 if (!e1000_phy_setup_autoneg(&adapter->hw) &&
4715 !e1000_read_phy_reg(&adapter->hw, PHY_CTRL,
4717 phy_ctrl |= (MII_CR_AUTO_NEG_EN |
4718 MII_CR_RESTART_AUTO_NEG);
4719 e1000_write_phy_reg(&adapter->hw, PHY_CTRL,
4724 } else if (adapter->smartspeed == E1000_SMARTSPEED_DOWNSHIFT) {
4725 /* If still no link, perhaps using 2/3 pair cable */
4726 e1000_read_phy_reg(&adapter->hw, PHY_1000T_CTRL, &phy_ctrl);
4727 phy_ctrl |= CR_1000T_MS_ENABLE;
4728 e1000_write_phy_reg(&adapter->hw, PHY_1000T_CTRL, phy_ctrl);
4729 if (!e1000_phy_setup_autoneg(&adapter->hw) &&
4730 !e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_ctrl)) {
4731 phy_ctrl |= (MII_CR_AUTO_NEG_EN |
4732 MII_CR_RESTART_AUTO_NEG);
4733 e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_ctrl);
4736 /* Restart process after E1000_SMARTSPEED_MAX iterations */
4737 if (adapter->smartspeed++ == E1000_SMARTSPEED_MAX)
4738 adapter->smartspeed = 0;
4749 e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
4755 return e1000_mii_ioctl(netdev, ifr, cmd);
4769 e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
4771 struct e1000_adapter *adapter = netdev_priv(netdev);
4772 struct mii_ioctl_data *data = if_mii(ifr);
4776 unsigned long flags;
4778 if (adapter->hw.media_type != e1000_media_type_copper)
4783 data->phy_id = adapter->hw.phy_addr;
4786 if (!capable(CAP_NET_ADMIN))
4788 spin_lock_irqsave(&adapter->stats_lock, flags);
4789 if (e1000_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
4791 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4794 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4797 if (!capable(CAP_NET_ADMIN))
4799 if (data->reg_num & ~(0x1F))
4801 mii_reg = data->val_in;
4802 spin_lock_irqsave(&adapter->stats_lock, flags);
4803 if (e1000_write_phy_reg(&adapter->hw, data->reg_num,
4805 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4808 if (adapter->hw.media_type == e1000_media_type_copper) {
4809 switch (data->reg_num) {
4811 if (mii_reg & MII_CR_POWER_DOWN)
4813 if (mii_reg & MII_CR_AUTO_NEG_EN) {
4814 adapter->hw.autoneg = 1;
4815 adapter->hw.autoneg_advertised = 0x2F;
4818 spddplx = SPEED_1000;
4819 else if (mii_reg & 0x2000)
4820 spddplx = SPEED_100;
4823 spddplx += (mii_reg & 0x100)
4826 retval = e1000_set_spd_dplx(adapter,
4829 spin_unlock_irqrestore(
4830 &adapter->stats_lock,
4835 if (netif_running(adapter->netdev))
4836 e1000_reinit_locked(adapter);
4838 e1000_reset(adapter);
4840 case M88E1000_PHY_SPEC_CTRL:
4841 case M88E1000_EXT_PHY_SPEC_CTRL:
4842 if (e1000_phy_reset(&adapter->hw)) {
4843 spin_unlock_irqrestore(
4844 &adapter->stats_lock, flags);
4850 switch (data->reg_num) {
4852 if (mii_reg & MII_CR_POWER_DOWN)
4854 if (netif_running(adapter->netdev))
4855 e1000_reinit_locked(adapter);
4857 e1000_reset(adapter);
4861 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4866 return E1000_SUCCESS;
4870 e1000_pci_set_mwi(struct e1000_hw *hw)
4872 struct e1000_adapter *adapter = hw->back;
4873 int ret_val = pci_set_mwi(adapter->pdev);
4876 DPRINTK(PROBE, ERR, "Error in setting MWI\n");
4880 e1000_pci_clear_mwi(struct e1000_hw *hw)
4882 struct e1000_adapter *adapter = hw->back;
4884 pci_clear_mwi(adapter->pdev);
4888 e1000_read_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t *value)
4890 struct e1000_adapter *adapter = hw->back;
4892 pci_read_config_word(adapter->pdev, reg, value);
4896 e1000_write_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t *value)
4898 struct e1000_adapter *adapter = hw->back;
4900 pci_write_config_word(adapter->pdev, reg, *value);
4904 e1000_read_pcie_cap_reg(struct e1000_hw *hw, uint32_t reg, uint16_t *value)
4906 struct e1000_adapter *adapter = hw->back;
4907 uint16_t cap_offset;
4909 cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
4911 return -E1000_ERR_CONFIG;
4913 pci_read_config_word(adapter->pdev, cap_offset + reg, value);
4915 return E1000_SUCCESS;
4919 e1000_io_write(struct e1000_hw *hw, unsigned long port, uint32_t value)
4925 e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp)
4927 struct e1000_adapter *adapter = netdev_priv(netdev);
4928 uint32_t ctrl, rctl;
4930 e1000_irq_disable(adapter);
4931 adapter->vlgrp = grp;
4934 /* enable VLAN tag insert/strip */
4935 ctrl = E1000_READ_REG(&adapter->hw, CTRL);
4936 ctrl |= E1000_CTRL_VME;
4937 E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
4939 if (adapter->hw.mac_type != e1000_ich8lan) {
4940 /* enable VLAN receive filtering */
4941 rctl = E1000_READ_REG(&adapter->hw, RCTL);
4942 rctl |= E1000_RCTL_VFE;
4943 rctl &= ~E1000_RCTL_CFIEN;
4944 E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
4945 e1000_update_mng_vlan(adapter);
4948 /* disable VLAN tag insert/strip */
4949 ctrl = E1000_READ_REG(&adapter->hw, CTRL);
4950 ctrl &= ~E1000_CTRL_VME;
4951 E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
4953 if (adapter->hw.mac_type != e1000_ich8lan) {
4954 /* disable VLAN filtering */
4955 rctl = E1000_READ_REG(&adapter->hw, RCTL);
4956 rctl &= ~E1000_RCTL_VFE;
4957 E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
4958 if (adapter->mng_vlan_id !=
4959 (uint16_t)E1000_MNG_VLAN_NONE) {
4960 e1000_vlan_rx_kill_vid(netdev,
4961 adapter->mng_vlan_id);
4962 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
4967 e1000_irq_enable(adapter);
4971 e1000_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid)
4973 struct e1000_adapter *adapter = netdev_priv(netdev);
4974 uint32_t vfta, index;
4976 if ((adapter->hw.mng_cookie.status &
4977 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
4978 (vid == adapter->mng_vlan_id))
4980 /* add VID to filter table */
4981 index = (vid >> 5) & 0x7F;
4982 vfta = E1000_READ_REG_ARRAY(&adapter->hw, VFTA, index);
4983 vfta |= (1 << (vid & 0x1F));
4984 e1000_write_vfta(&adapter->hw, index, vfta);
4988 e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid)
4990 struct e1000_adapter *adapter = netdev_priv(netdev);
4991 uint32_t vfta, index;
4993 e1000_irq_disable(adapter);
4994 vlan_group_set_device(adapter->vlgrp, vid, NULL);
4995 e1000_irq_enable(adapter);
4997 if ((adapter->hw.mng_cookie.status &
4998 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
4999 (vid == adapter->mng_vlan_id)) {
5000 /* release control to f/w */
5001 e1000_release_hw_control(adapter);
5005 /* remove VID from filter table */
5006 index = (vid >> 5) & 0x7F;
5007 vfta = E1000_READ_REG_ARRAY(&adapter->hw, VFTA, index);
5008 vfta &= ~(1 << (vid & 0x1F));
5009 e1000_write_vfta(&adapter->hw, index, vfta);
5013 e1000_restore_vlan(struct e1000_adapter *adapter)
5015 e1000_vlan_rx_register(adapter->netdev, adapter->vlgrp);
5017 if (adapter->vlgrp) {
5019 for (vid = 0; vid < VLAN_GROUP_ARRAY_LEN; vid++) {
5020 if (!vlan_group_get_device(adapter->vlgrp, vid))
5022 e1000_vlan_rx_add_vid(adapter->netdev, vid);
5028 e1000_set_spd_dplx(struct e1000_adapter *adapter, uint16_t spddplx)
5030 adapter->hw.autoneg = 0;
5032 /* Fiber NICs only allow 1000 gbps Full duplex */
5033 if ((adapter->hw.media_type == e1000_media_type_fiber) &&
5034 spddplx != (SPEED_1000 + DUPLEX_FULL)) {
5035 DPRINTK(PROBE, ERR, "Unsupported Speed/Duplex configuration\n");
5040 case SPEED_10 + DUPLEX_HALF:
5041 adapter->hw.forced_speed_duplex = e1000_10_half;
5043 case SPEED_10 + DUPLEX_FULL:
5044 adapter->hw.forced_speed_duplex = e1000_10_full;
5046 case SPEED_100 + DUPLEX_HALF:
5047 adapter->hw.forced_speed_duplex = e1000_100_half;
5049 case SPEED_100 + DUPLEX_FULL:
5050 adapter->hw.forced_speed_duplex = e1000_100_full;
5052 case SPEED_1000 + DUPLEX_FULL:
5053 adapter->hw.autoneg = 1;
5054 adapter->hw.autoneg_advertised = ADVERTISE_1000_FULL;
5056 case SPEED_1000 + DUPLEX_HALF: /* not supported */
5058 DPRINTK(PROBE, ERR, "Unsupported Speed/Duplex configuration\n");
5065 e1000_suspend(struct pci_dev *pdev, pm_message_t state)
5067 struct net_device *netdev = pci_get_drvdata(pdev);
5068 struct e1000_adapter *adapter = netdev_priv(netdev);
5069 uint32_t ctrl, ctrl_ext, rctl, status;
5070 uint32_t wufc = adapter->wol;
5075 netif_device_detach(netdev);
5077 if (netif_running(netdev)) {
5078 WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
5079 e1000_down(adapter);
5083 retval = pci_save_state(pdev);
5088 status = E1000_READ_REG(&adapter->hw, STATUS);
5089 if (status & E1000_STATUS_LU)
5090 wufc &= ~E1000_WUFC_LNKC;
5093 e1000_setup_rctl(adapter);
5094 e1000_set_multi(netdev);
5096 /* turn on all-multi mode if wake on multicast is enabled */
5097 if (wufc & E1000_WUFC_MC) {
5098 rctl = E1000_READ_REG(&adapter->hw, RCTL);
5099 rctl |= E1000_RCTL_MPE;
5100 E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
5103 if (adapter->hw.mac_type >= e1000_82540) {
5104 ctrl = E1000_READ_REG(&adapter->hw, CTRL);
5105 /* advertise wake from D3Cold */
5106 #define E1000_CTRL_ADVD3WUC 0x00100000
5107 /* phy power management enable */
5108 #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
5109 ctrl |= E1000_CTRL_ADVD3WUC |
5110 E1000_CTRL_EN_PHY_PWR_MGMT;
5111 E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
5114 if (adapter->hw.media_type == e1000_media_type_fiber ||
5115 adapter->hw.media_type == e1000_media_type_internal_serdes) {
5116 /* keep the laser running in D3 */
5117 ctrl_ext = E1000_READ_REG(&adapter->hw, CTRL_EXT);
5118 ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
5119 E1000_WRITE_REG(&adapter->hw, CTRL_EXT, ctrl_ext);
5122 /* Allow time for pending master requests to run */
5123 e1000_disable_pciex_master(&adapter->hw);
5125 E1000_WRITE_REG(&adapter->hw, WUC, E1000_WUC_PME_EN);
5126 E1000_WRITE_REG(&adapter->hw, WUFC, wufc);
5127 pci_enable_wake(pdev, PCI_D3hot, 1);
5128 pci_enable_wake(pdev, PCI_D3cold, 1);
5130 E1000_WRITE_REG(&adapter->hw, WUC, 0);
5131 E1000_WRITE_REG(&adapter->hw, WUFC, 0);
5132 pci_enable_wake(pdev, PCI_D3hot, 0);
5133 pci_enable_wake(pdev, PCI_D3cold, 0);
5136 e1000_release_manageability(adapter);
5138 /* make sure adapter isn't asleep if manageability is enabled */
5139 if (adapter->en_mng_pt) {
5140 pci_enable_wake(pdev, PCI_D3hot, 1);
5141 pci_enable_wake(pdev, PCI_D3cold, 1);
5144 if (adapter->hw.phy_type == e1000_phy_igp_3)
5145 e1000_phy_powerdown_workaround(&adapter->hw);
5147 if (netif_running(netdev))
5148 e1000_free_irq(adapter);
5150 /* Release control of h/w to f/w. If f/w is AMT enabled, this
5151 * would have already happened in close and is redundant. */
5152 e1000_release_hw_control(adapter);
5154 pci_disable_device(pdev);
5156 pci_set_power_state(pdev, pci_choose_state(pdev, state));
5163 e1000_resume(struct pci_dev *pdev)
5165 struct net_device *netdev = pci_get_drvdata(pdev);
5166 struct e1000_adapter *adapter = netdev_priv(netdev);
5169 pci_set_power_state(pdev, PCI_D0);
5170 pci_restore_state(pdev);
5171 if ((err = pci_enable_device(pdev))) {
5172 printk(KERN_ERR "e1000: Cannot enable PCI device from suspend\n");
5175 pci_set_master(pdev);
5177 pci_enable_wake(pdev, PCI_D3hot, 0);
5178 pci_enable_wake(pdev, PCI_D3cold, 0);
5180 if (netif_running(netdev) && (err = e1000_request_irq(adapter)))
5183 e1000_power_up_phy(adapter);
5184 e1000_reset(adapter);
5185 E1000_WRITE_REG(&adapter->hw, WUS, ~0);
5187 e1000_init_manageability(adapter);
5189 if (netif_running(netdev))
5192 netif_device_attach(netdev);
5194 /* If the controller is 82573 and f/w is AMT, do not set
5195 * DRV_LOAD until the interface is up. For all other cases,
5196 * let the f/w know that the h/w is now under the control
5198 if (adapter->hw.mac_type != e1000_82573 ||
5199 !e1000_check_mng_mode(&adapter->hw))
5200 e1000_get_hw_control(adapter);
5206 static void e1000_shutdown(struct pci_dev *pdev)
5208 e1000_suspend(pdev, PMSG_SUSPEND);
5211 #ifdef CONFIG_NET_POLL_CONTROLLER
5213 * Polling 'interrupt' - used by things like netconsole to send skbs
5214 * without having to re-enable interrupts. It's not called while
5215 * the interrupt routine is executing.
5218 e1000_netpoll(struct net_device *netdev)
5220 struct e1000_adapter *adapter = netdev_priv(netdev);
5222 disable_irq(adapter->pdev->irq);
5223 e1000_intr(adapter->pdev->irq, netdev);
5224 e1000_clean_tx_irq(adapter, adapter->tx_ring);
5225 #ifndef CONFIG_E1000_NAPI
5226 adapter->clean_rx(adapter, adapter->rx_ring);
5228 enable_irq(adapter->pdev->irq);
5233 * e1000_io_error_detected - called when PCI error is detected
5234 * @pdev: Pointer to PCI device
5235 * @state: The current pci conneection state
5237 * This function is called after a PCI bus error affecting
5238 * this device has been detected.
5240 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev, pci_channel_state_t state)
5242 struct net_device *netdev = pci_get_drvdata(pdev);
5243 struct e1000_adapter *adapter = netdev->priv;
5245 netif_device_detach(netdev);
5247 if (netif_running(netdev))
5248 e1000_down(adapter);
5249 pci_disable_device(pdev);
5251 /* Request a slot slot reset. */
5252 return PCI_ERS_RESULT_NEED_RESET;
5256 * e1000_io_slot_reset - called after the pci bus has been reset.
5257 * @pdev: Pointer to PCI device
5259 * Restart the card from scratch, as if from a cold-boot. Implementation
5260 * resembles the first-half of the e1000_resume routine.
5262 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
5264 struct net_device *netdev = pci_get_drvdata(pdev);
5265 struct e1000_adapter *adapter = netdev->priv;
5267 if (pci_enable_device(pdev)) {
5268 printk(KERN_ERR "e1000: Cannot re-enable PCI device after reset.\n");
5269 return PCI_ERS_RESULT_DISCONNECT;
5271 pci_set_master(pdev);
5273 pci_enable_wake(pdev, PCI_D3hot, 0);
5274 pci_enable_wake(pdev, PCI_D3cold, 0);
5276 e1000_reset(adapter);
5277 E1000_WRITE_REG(&adapter->hw, WUS, ~0);
5279 return PCI_ERS_RESULT_RECOVERED;
5283 * e1000_io_resume - called when traffic can start flowing again.
5284 * @pdev: Pointer to PCI device
5286 * This callback is called when the error recovery driver tells us that
5287 * its OK to resume normal operation. Implementation resembles the
5288 * second-half of the e1000_resume routine.
5290 static void e1000_io_resume(struct pci_dev *pdev)
5292 struct net_device *netdev = pci_get_drvdata(pdev);
5293 struct e1000_adapter *adapter = netdev->priv;
5295 e1000_init_manageability(adapter);
5297 if (netif_running(netdev)) {
5298 if (e1000_up(adapter)) {
5299 printk("e1000: can't bring device back up after reset\n");
5304 netif_device_attach(netdev);
5306 /* If the controller is 82573 and f/w is AMT, do not set
5307 * DRV_LOAD until the interface is up. For all other cases,
5308 * let the f/w know that the h/w is now under the control
5310 if (adapter->hw.mac_type != e1000_82573 ||
5311 !e1000_check_mng_mode(&adapter->hw))
5312 e1000_get_hw_control(adapter);