err.no Git - linux-2.6/blob - drivers/media/video/cx18/cx18-firmware.c

   1 /*
   2  *  cx18 firmware functions
   3  *
   4  *  Copyright (C) 2007  Hans Verkuil <hverkuil@xs4all.nl>
   5  *
   6  *  This program is free software; you can redistribute it and/or modify
   7  *  it under the terms of the GNU General Public License as published by
   8  *  the Free Software Foundation; either version 2 of the License, or
   9  *  (at your option) any later version.
  10  *
  11  *  This program is distributed in the hope that it will be useful,
  12  *  but WITHOUT ANY WARRANTY; without even the implied warranty of
  13  *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  14  *  GNU General Public License for more details.
  15  *
  16  *  You should have received a copy of the GNU General Public License
  17  *  along with this program; if not, write to the Free Software
  18  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
  19  *  02111-1307  USA
  20  */
  21
  22 #include "cx18-driver.h"
  23 #include "cx18-scb.h"
  24 #include "cx18-irq.h"
  25 #include "cx18-firmware.h"
  26 #include "cx18-cards.h"
  27 #include <linux/firmware.h>
  28
  29 #define CX18_PROC_SOFT_RESET            0xc70010
  30 #define CX18_DDR_SOFT_RESET             0xc70014
  31 #define CX18_CLOCK_SELECT1              0xc71000
  32 #define CX18_CLOCK_SELECT2              0xc71004
  33 #define CX18_HALF_CLOCK_SELECT1         0xc71008
  34 #define CX18_HALF_CLOCK_SELECT2         0xc7100C
  35 #define CX18_CLOCK_POLARITY1            0xc71010
  36 #define CX18_CLOCK_POLARITY2            0xc71014
  37 #define CX18_ADD_DELAY_ENABLE1          0xc71018
  38 #define CX18_ADD_DELAY_ENABLE2          0xc7101C
  39 #define CX18_CLOCK_ENABLE1              0xc71020
  40 #define CX18_CLOCK_ENABLE2              0xc71024
  41
  42 #define CX18_REG_BUS_TIMEOUT_EN         0xc72024
  43
  44 #define CX18_AUDIO_ENABLE               0xc72014
  45 #define CX18_REG_BUS_TIMEOUT_EN         0xc72024
  46
  47 #define CX18_FAST_CLOCK_PLL_INT         0xc78000
  48 #define CX18_FAST_CLOCK_PLL_FRAC        0xc78004
  49 #define CX18_FAST_CLOCK_PLL_POST        0xc78008
  50 #define CX18_FAST_CLOCK_PLL_PRESCALE    0xc7800C
  51 #define CX18_FAST_CLOCK_PLL_ADJUST_BANDWIDTH 0xc78010
  52
  53 #define CX18_SLOW_CLOCK_PLL_INT         0xc78014
  54 #define CX18_SLOW_CLOCK_PLL_FRAC        0xc78018
  55 #define CX18_SLOW_CLOCK_PLL_POST        0xc7801C
  56 #define CX18_MPEG_CLOCK_PLL_INT         0xc78040
  57 #define CX18_MPEG_CLOCK_PLL_FRAC        0xc78044
  58 #define CX18_MPEG_CLOCK_PLL_POST        0xc78048
  59 #define CX18_PLL_POWER_DOWN             0xc78088
  60 #define CX18_SW1_INT_STATUS             0xc73104
  61 #define CX18_SW1_INT_ENABLE_PCI         0xc7311C
  62 #define CX18_SW2_INT_SET                0xc73140
  63 #define CX18_SW2_INT_STATUS             0xc73144
  64 #define CX18_ADEC_CONTROL               0xc78120
  65
  66 #define CX18_DDR_REQUEST_ENABLE         0xc80000
  67 #define CX18_DDR_CHIP_CONFIG            0xc80004
  68 #define CX18_DDR_REFRESH                0xc80008
  69 #define CX18_DDR_TIMING1                0xc8000C
  70 #define CX18_DDR_TIMING2                0xc80010
  71 #define CX18_DDR_POWER_REG              0xc8001C
  72
  73 #define CX18_DDR_TUNE_LANE              0xc80048
  74 #define CX18_DDR_INITIAL_EMRS           0xc80054
  75 #define CX18_DDR_MB_PER_ROW_7           0xc8009C
  76 #define CX18_DDR_BASE_63_ADDR           0xc804FC
  77
  78 #define CX18_WMB_CLIENT02               0xc90108
  79 #define CX18_WMB_CLIENT05               0xc90114
  80 #define CX18_WMB_CLIENT06               0xc90118
  81 #define CX18_WMB_CLIENT07               0xc9011C
  82 #define CX18_WMB_CLIENT08               0xc90120
  83 #define CX18_WMB_CLIENT09               0xc90124
  84 #define CX18_WMB_CLIENT10               0xc90128
  85 #define CX18_WMB_CLIENT11               0xc9012C
  86 #define CX18_WMB_CLIENT12               0xc90130
  87 #define CX18_WMB_CLIENT13               0xc90134
  88 #define CX18_WMB_CLIENT14               0xc90138
  89
  90 #define CX18_DSP0_INTERRUPT_MASK        0xd0004C
  91
  92 /* Encoder/decoder firmware sizes */
  93 #define CX18_FW_CPU_SIZE                (174716)
  94 #define CX18_FW_APU_SIZE                (141200)
  95
  96 #define APU_ROM_SYNC1 0x6D676553 /* "mgeS" */
  97 #define APU_ROM_SYNC2 0x72646548 /* "rdeH" */
  98
  99 struct cx18_apu_rom_seghdr {
 100         u32 sync1;
 101         u32 sync2;
 102         u32 addr;
 103         u32 size;
 104 };
 105
 106 static int load_cpu_fw_direct(const char *fn, u8 __iomem *mem, struct cx18 *cx, long size)
 107 {
 108         const struct firmware *fw = NULL;
 109         int retries = 3;
 110         int i, j;
 111         u32 __iomem *dst = (u32 __iomem *)mem;
 112         const u32 *src;
 113
 114 retry:
 115         if (!retries || request_firmware(&fw, fn, &cx->dev->dev)) {
 116                 CX18_ERR("Unable to open firmware %s (must be %ld bytes)\n",
 117                                 fn, size);
 118                 CX18_ERR("Did you put the firmware in the hotplug firmware directory?\n");
 119                 return -ENOMEM;
 120         }
 121
 122         src = (const u32 *)fw->data;
 123
 124         if (fw->size != size) {
 125                 /* Due to race conditions in firmware loading (esp. with
 126                    udev <0.95) the wrong file was sometimes loaded. So we check
 127                    filesizes to see if at least the right-sized file was
 128                    loaded. If not, then we retry. */
 129                 CX18_INFO("retry: file loaded was not %s (expected size %ld, got %zd)\n",
 130                                 fn, size, fw->size);
 131                 release_firmware(fw);
 132                 retries--;
 133                 goto retry;
 134         }
 135         for (i = 0; i < fw->size; i += 4096) {
 136                 setup_page(i);
 137                 for (j = i; j < fw->size && j < i + 4096; j += 4) {
 138                         /* no need for endianness conversion on the ppc */
 139                         __raw_writel(*src, dst);
 140                         if (__raw_readl(dst) != *src) {
 141                                 CX18_ERR("Mismatch at offset %x\n", i);
 142                                 release_firmware(fw);
 143                                 return -EIO;
 144                         }
 145                         dst++;
 146                         src++;
 147                 }
 148         }
 149         if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
 150                 CX18_INFO("loaded %s firmware (%zd bytes)\n", fn, fw->size);
 151         release_firmware(fw);
 152         return size;
 153 }
 154
 155 static int load_apu_fw_direct(const char *fn, u8 __iomem *dst, struct cx18 *cx, long size)
 156 {
 157         const struct firmware *fw = NULL;
 158         int retries = 3;
 159         int i, j;
 160         const u32 *src;
 161         struct cx18_apu_rom_seghdr seghdr;
 162         const u8 *vers;
 163         u32 offset = 0;
 164         u32 apu_version = 0;
 165         int sz;
 166
 167 retry:
 168         if (!retries || request_firmware(&fw, fn, &cx->dev->dev)) {
 169                 CX18_ERR("unable to open firmware %s (must be %ld bytes)\n",
 170                                 fn, size);
 171                 CX18_ERR("did you put the firmware in the hotplug firmware directory?\n");
 172                 return -ENOMEM;
 173         }
 174
 175         src = (const u32 *)fw->data;
 176         vers = fw->data + sizeof(seghdr);
 177         sz = fw->size;
 178
 179         if (fw->size != size) {
 180                 /* Due to race conditions in firmware loading (esp. with
 181                    udev <0.95) the wrong file was sometimes loaded. So we check
 182                    filesizes to see if at least the right-sized file was
 183                    loaded. If not, then we retry. */
 184                 CX18_INFO("retry: file loaded was not %s (expected size %ld, got %zd)\n",
 185                                fn, size, fw->size);
 186                 release_firmware(fw);
 187                 retries--;
 188                 goto retry;
 189         }
 190         apu_version = (vers[0] << 24) | (vers[4] << 16) | vers[32];
 191         while (offset + sizeof(seghdr) < size) {
 192                 /* TODO: byteswapping */
 193                 memcpy(&seghdr, src + offset / 4, sizeof(seghdr));
 194                 offset += sizeof(seghdr);
 195                 if (seghdr.sync1 != APU_ROM_SYNC1 ||
 196                     seghdr.sync2 != APU_ROM_SYNC2) {
 197                         offset += seghdr.size;
 198                         continue;
 199                 }
 200                 CX18_DEBUG_INFO("load segment %x-%x\n", seghdr.addr,
 201                                 seghdr.addr + seghdr.size - 1);
 202                 if (offset + seghdr.size > sz)
 203                         break;
 204                 for (i = 0; i < seghdr.size; i += 4096) {
 205                         setup_page(offset + i);
 206                         for (j = i; j < seghdr.size && j < i + 4096; j += 4) {
 207                                 /* no need for endianness conversion on the ppc */
 208                                 __raw_writel(src[(offset + j) / 4], dst + seghdr.addr + j);
 209                                 if (__raw_readl(dst + seghdr.addr + j) != src[(offset + j) / 4]) {
 210                                         CX18_ERR("Mismatch at offset %x\n", offset + j);
 211                                         release_firmware(fw);
 212                                         return -EIO;
 213                                 }
 214                         }
 215                 }
 216                 offset += seghdr.size;
 217         }
 218         if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
 219                 CX18_INFO("loaded %s firmware V%08x (%zd bytes)\n",
 220                                 fn, apu_version, fw->size);
 221         release_firmware(fw);
 222         /* Clear bit0 for APU to start from 0 */
 223         write_reg(read_reg(0xc72030) & ~1, 0xc72030);
 224         return size;
 225 }
 226
 227 void cx18_halt_firmware(struct cx18 *cx)
 228 {
 229         CX18_DEBUG_INFO("Preparing for firmware halt.\n");
 230         write_reg(0x000F000F, CX18_PROC_SOFT_RESET); /* stop the fw */
 231         write_reg(0x00020002, CX18_ADEC_CONTROL);
 232 }
 233
 234 void cx18_init_power(struct cx18 *cx, int lowpwr)
 235 {
 236         /* power-down Spare and AOM PLLs */
 237         /* power-up fast, slow and mpeg PLLs */
 238         write_reg(0x00000008, CX18_PLL_POWER_DOWN);
 239
 240         /* ADEC out of sleep */
 241         write_reg(0x00020000, CX18_ADEC_CONTROL);
 242
 243         /* The fast clock is at 200/245 MHz */
 244         write_reg(lowpwr ? 0xD : 0x11, CX18_FAST_CLOCK_PLL_INT);
 245         write_reg(lowpwr ? 0x1EFBF37 : 0x038E3D7, CX18_FAST_CLOCK_PLL_FRAC);
 246
 247         write_reg(2, CX18_FAST_CLOCK_PLL_POST);
 248         write_reg(1, CX18_FAST_CLOCK_PLL_PRESCALE);
 249         write_reg(4, CX18_FAST_CLOCK_PLL_ADJUST_BANDWIDTH);
 250
 251         /* set slow clock to 125/120 MHz */
 252         write_reg(lowpwr ? 0x11 : 0x10, CX18_SLOW_CLOCK_PLL_INT);
 253         write_reg(lowpwr ? 0xEBAF05 : 0x18618A8, CX18_SLOW_CLOCK_PLL_FRAC);
 254         write_reg(4, CX18_SLOW_CLOCK_PLL_POST);
 255
 256         /* mpeg clock pll 54MHz */
 257         write_reg(0xF, CX18_MPEG_CLOCK_PLL_INT);
 258         write_reg(0x2BCFEF, CX18_MPEG_CLOCK_PLL_FRAC);
 259         write_reg(8, CX18_MPEG_CLOCK_PLL_POST);
 260
 261         /* Defaults */
 262         /* APU = SC or SC/2 = 125/62.5 */
 263         /* EPU = SC = 125 */
 264         /* DDR = FC = 180 */
 265         /* ENC = SC = 125 */
 266         /* AI1 = SC = 125 */
 267         /* VIM2 = disabled */
 268         /* PCI = FC/2 = 90 */
 269         /* AI2 = disabled */
 270         /* DEMUX = disabled */
 271         /* AO = SC/2 = 62.5 */
 272         /* SER = 54MHz */
 273         /* VFC = disabled */
 274         /* USB = disabled */
 275
 276         write_reg(lowpwr ? 0xFFFF0020 : 0x00060004, CX18_CLOCK_SELECT1);
 277         write_reg(lowpwr ? 0xFFFF0004 : 0x00060006, CX18_CLOCK_SELECT2);
 278
 279         write_reg(0xFFFF0002, CX18_HALF_CLOCK_SELECT1);
 280         write_reg(0xFFFF0104, CX18_HALF_CLOCK_SELECT2);
 281
 282         write_reg(0xFFFF9026, CX18_CLOCK_ENABLE1);
 283         write_reg(0xFFFF3105, CX18_CLOCK_ENABLE2);
 284 }
 285
 286 void cx18_init_memory(struct cx18 *cx)
 287 {
 288         cx18_msleep_timeout(10, 0);
 289         write_reg(0x10000, CX18_DDR_SOFT_RESET);
 290         cx18_msleep_timeout(10, 0);
 291
 292         write_reg(cx->card->ddr.chip_config, CX18_DDR_CHIP_CONFIG);
 293
 294         cx18_msleep_timeout(10, 0);
 295
 296         write_reg(cx->card->ddr.refresh, CX18_DDR_REFRESH);
 297         write_reg(cx->card->ddr.timing1, CX18_DDR_TIMING1);
 298         write_reg(cx->card->ddr.timing2, CX18_DDR_TIMING2);
 299
 300         cx18_msleep_timeout(10, 0);
 301
 302         /* Initialize DQS pad time */
 303         write_reg(cx->card->ddr.tune_lane, CX18_DDR_TUNE_LANE);
 304         write_reg(cx->card->ddr.initial_emrs, CX18_DDR_INITIAL_EMRS);
 305
 306         cx18_msleep_timeout(10, 0);
 307
 308         write_reg(0x20000, CX18_DDR_SOFT_RESET);
 309         cx18_msleep_timeout(10, 0);
 310
 311         /* use power-down mode when idle */
 312         write_reg(0x00000010, CX18_DDR_POWER_REG);
 313
 314         write_reg(0x10001, CX18_REG_BUS_TIMEOUT_EN);
 315
 316         write_reg(0x48, CX18_DDR_MB_PER_ROW_7);
 317         write_reg(0xE0000, CX18_DDR_BASE_63_ADDR);
 318
 319         write_reg(0x00000101, CX18_WMB_CLIENT02);  /* AO */
 320         write_reg(0x00000101, CX18_WMB_CLIENT09);  /* AI2 */
 321         write_reg(0x00000101, CX18_WMB_CLIENT05);  /* VIM1 */
 322         write_reg(0x00000101, CX18_WMB_CLIENT06);  /* AI1 */
 323         write_reg(0x00000101, CX18_WMB_CLIENT07);  /* 3D comb */
 324         write_reg(0x00000101, CX18_WMB_CLIENT10);  /* ME */
 325         write_reg(0x00000101, CX18_WMB_CLIENT12);  /* ENC */
 326         write_reg(0x00000101, CX18_WMB_CLIENT13);  /* PK */
 327         write_reg(0x00000101, CX18_WMB_CLIENT11);  /* RC */
 328         write_reg(0x00000101, CX18_WMB_CLIENT14);  /* AVO */
 329 }
 330
 331 int cx18_firmware_init(struct cx18 *cx)
 332 {
 333         /* Allow chip to control CLKRUN */
 334         write_reg(0x5, CX18_DSP0_INTERRUPT_MASK);
 335
 336         write_reg(0x000F000F, CX18_PROC_SOFT_RESET); /* stop the fw */
 337
 338         cx18_msleep_timeout(1, 0);
 339
 340         sw1_irq_enable(IRQ_CPU_TO_EPU | IRQ_APU_TO_EPU);
 341         sw2_irq_enable(IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);
 342
 343         /* Only if the processor is not running */
 344         if (read_reg(CX18_PROC_SOFT_RESET) & 8) {
 345                 int sz = load_apu_fw_direct("v4l-cx23418-apu.fw",
 346                                cx->enc_mem, cx, CX18_FW_APU_SIZE);
 347
 348                 sz = sz <= 0 ? sz : load_cpu_fw_direct("v4l-cx23418-cpu.fw",
 349                                         cx->enc_mem, cx, CX18_FW_CPU_SIZE);
 350
 351                 if (sz > 0) {
 352                         int retries = 0;
 353
 354                         /* start the CPU */
 355                         write_reg(0x00080000, CX18_PROC_SOFT_RESET);
 356                         while (retries++ < 50) { /* Loop for max 500mS */
 357                                 if ((read_reg(CX18_PROC_SOFT_RESET) & 1) == 0)
 358                                         break;
 359                                 cx18_msleep_timeout(10, 0);
 360                         }
 361                         cx18_msleep_timeout(200, 0);
 362                         if (retries == 51) {
 363                                 CX18_ERR("Could not start the CPU\n");
 364                                 return -EIO;
 365                         }
 366                 }
 367                 if (sz <= 0)
 368                         return -EIO;
 369         }
 370         /* initialize GPIO */
 371         write_reg(0x14001400, 0xC78110);
 372         return 0;
 373 }