err.no Git - linux-2.6/blob - drivers/input/touchscreen/wm9712.c

   1 /*
   2  * wm9712.c  --  Codec driver for Wolfson WM9712 AC97 Codecs.
   3  *
   4  * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
   5  * Author: Liam Girdwood
   6  *         liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
   7  * Parts Copyright : Ian Molton <spyro@f2s.com>
   8  *                   Andrew Zabolotny <zap@homelink.ru>
   9  *                   Russell King <rmk@arm.linux.org.uk>
  10  *
  11  *  This program is free software; you can redistribute  it and/or modify it
  12  *  under  the terms of  the GNU General  Public License as published by the
  13  *  Free Software Foundation;  either version 2 of the  License, or (at your
  14  *  option) any later version.
  15  *
  16  */
  17
  18 #include <linux/module.h>
  19 #include <linux/moduleparam.h>
  20 #include <linux/kernel.h>
  21 #include <linux/input.h>
  22 #include <linux/delay.h>
  23 #include <linux/bitops.h>
  24 #include <linux/wm97xx.h>
  25
  26 #define TS_NAME                 "wm97xx"
  27 #define WM9712_VERSION          "1.00"
  28 #define DEFAULT_PRESSURE        0xb0c0
  29
  30 /*
  31  * Module parameters
  32  */
  33
  34 /*
  35  * Set internal pull up for pen detect.
  36  *
  37  * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
  38  * i.e. pull up resistance = 64k Ohms / rpu.
  39  *
  40  * Adjust this value if you are having problems with pen detect not
  41  * detecting any down event.
  42  */
  43 static int rpu = 8;
  44 module_param(rpu, int, 0);
  45 MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
  46
  47 /*
  48  * Set current used for pressure measurement.
  49  *
  50  * Set pil = 2 to use 400uA
  51  *     pil = 1 to use 200uA and
  52  *     pil = 0 to disable pressure measurement.
  53  *
  54  * This is used to increase the range of values returned by the adc
  55  * when measureing touchpanel pressure.
  56  */
  57 static int pil;
  58 module_param(pil, int, 0);
  59 MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
  60
  61 /*
  62  * Set threshold for pressure measurement.
  63  *
  64  * Pen down pressure below threshold is ignored.
  65  */
  66 static int pressure = DEFAULT_PRESSURE & 0xfff;
  67 module_param(pressure, int, 0);
  68 MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
  69
  70 /*
  71  * Set adc sample delay.
  72  *
  73  * For accurate touchpanel measurements, some settling time may be
  74  * required between the switch matrix applying a voltage across the
  75  * touchpanel plate and the ADC sampling the signal.
  76  *
  77  * This delay can be set by setting delay = n, where n is the array
  78  * position of the delay in the array delay_table below.
  79  * Long delays > 1ms are supported for completeness, but are not
  80  * recommended.
  81  */
  82 static int delay = 3;
  83 module_param(delay, int, 0);
  84 MODULE_PARM_DESC(delay, "Set adc sample delay.");
  85
  86 /*
  87  * Set five_wire = 1 to use a 5 wire touchscreen.
  88  *
  89  * NOTE: Five wire mode does not allow for readback of pressure.
  90  */
  91 static int five_wire;
  92 module_param(five_wire, int, 0);
  93 MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");
  94
  95 /*
  96  * Set adc mask function.
  97  *
  98  * Sources of glitch noise, such as signals driving an LCD display, may feed
  99  * through to the touch screen plates and affect measurement accuracy. In
 100  * order to minimise this, a signal may be applied to the MASK pin to delay or
 101  * synchronise the sampling.
 102  *
 103  * 0 = No delay or sync
 104  * 1 = High on pin stops conversions
 105  * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
 106  * 3 = Edge triggered, edge on pin starts conversion after delay param
 107  */
 108 static int mask;
 109 module_param(mask, int, 0);
 110 MODULE_PARM_DESC(mask, "Set adc mask function.");
 111
 112 /*
 113  * Coordinate Polling Enable.
 114  *
 115  * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
 116  * for every poll.
 117  */
 118 static int coord;
 119 module_param(coord, int, 0);
 120 MODULE_PARM_DESC(coord, "Polling coordinate mode");
 121
 122 /*
 123  * ADC sample delay times in uS
 124  */
 125 static const int delay_table[] = {
 126         21,    /* 1 AC97 Link frames */
 127         42,    /* 2 */
 128         84,    /* 4 */
 129         167,   /* 8 */
 130         333,   /* 16 */
 131         667,   /* 32 */
 132         1000,  /* 48 */
 133         1333,  /* 64 */
 134         2000,  /* 96 */
 135         2667,  /* 128 */
 136         3333,  /* 160 */
 137         4000,  /* 192 */
 138         4667,  /* 224 */
 139         5333,  /* 256 */
 140         6000,  /* 288 */
 141         0      /* No delay, switch matrix always on */
 142 };
 143
 144 /*
 145  * Delay after issuing a POLL command.
 146  *
 147  * The delay is 3 AC97 link frames + the touchpanel settling delay
 148  */
 149 static inline void poll_delay(int d)
 150 {
 151         udelay(3 * AC97_LINK_FRAME + delay_table[d]);
 152 }
 153
 154 /*
 155  * set up the physical settings of the WM9712
 156  */
 157 static void wm9712_phy_init(struct wm97xx *wm)
 158 {
 159         u16 dig1 = 0;
 160         u16 dig2 = WM97XX_RPR | WM9712_RPU(1);
 161
 162         /* WM9712 rpu */
 163         if (rpu) {
 164                 dig2 &= 0xffc0;
 165                 dig2 |= WM9712_RPU(rpu);
 166                 dev_dbg(wm->dev, "setting pen detect pull-up to %d Ohms",
 167                         64000 / rpu);
 168         }
 169
 170         /* WM9712 five wire */
 171         if (five_wire) {
 172                 dig2 |= WM9712_45W;
 173                 dev_dbg(wm->dev, "setting 5-wire touchscreen mode.");
 174
 175                 if (pil) {
 176                         dev_warn(wm->dev, "pressure measurement is not "
 177                                  "supported in 5-wire mode\n");
 178                         pil = 0;
 179                 }
 180         }
 181
 182         /* touchpanel pressure current*/
 183         if (pil == 2) {
 184                 dig2 |= WM9712_PIL;
 185                 dev_dbg(wm->dev,
 186                         "setting pressure measurement current to 400uA.");
 187         } else if (pil)
 188                 dev_dbg(wm->dev,
 189                         "setting pressure measurement current to 200uA.");
 190         if (!pil)
 191                 pressure = 0;
 192
 193         /* polling mode sample settling delay */
 194         if (delay < 0 || delay > 15) {
 195                 dev_dbg(wm->dev, "supplied delay out of range.");
 196                 delay = 4;
 197         }
 198         dig1 &= 0xff0f;
 199         dig1 |= WM97XX_DELAY(delay);
 200         dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
 201                 delay_table[delay]);
 202
 203         /* mask */
 204         dig2 |= ((mask & 0x3) << 6);
 205         if (mask) {
 206                 u16 reg;
 207                 /* Set GPIO4 as Mask Pin*/
 208                 reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
 209                 wm97xx_reg_write(wm, AC97_MISC_AFE, reg | WM97XX_GPIO_4);
 210                 reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
 211                 wm97xx_reg_write(wm, AC97_GPIO_CFG, reg | WM97XX_GPIO_4);
 212         }
 213
 214         /* wait - coord mode */
 215         if (coord)
 216                 dig2 |= WM9712_WAIT;
 217
 218         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
 219         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
 220 }
 221
 222 static void wm9712_dig_enable(struct wm97xx *wm, int enable)
 223 {
 224         u16 dig2 = wm->dig[2];
 225
 226         if (enable) {
 227                 wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
 228                                  dig2 | WM97XX_PRP_DET_DIG);
 229                 wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
 230         } else
 231                 wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
 232                                  dig2 & ~WM97XX_PRP_DET_DIG);
 233 }
 234
 235 static void wm9712_aux_prepare(struct wm97xx *wm)
 236 {
 237         memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
 238         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
 239         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
 240 }
 241
 242 static void wm9712_dig_restore(struct wm97xx *wm)
 243 {
 244         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
 245         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
 246 }
 247
 248 static inline int is_pden(struct wm97xx *wm)
 249 {
 250         return wm->dig[2] & WM9712_PDEN;
 251 }
 252
 253 /*
 254  * Read a sample from the WM9712 adc in polling mode.
 255  */
 256 static int wm9712_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
 257 {
 258         int timeout = 5 * delay;
 259
 260         if (!wm->pen_probably_down) {
 261                 u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
 262                 if (!(data & WM97XX_PEN_DOWN))
 263                         return RC_PENUP;
 264                 wm->pen_probably_down = 1;
 265         }
 266
 267         /* set up digitiser */
 268         if (adcsel & 0x8000)
 269                 adcsel = ((adcsel & 0x7fff) + 3) << 12;
 270
 271         if (wm->mach_ops && wm->mach_ops->pre_sample)
 272                 wm->mach_ops->pre_sample(adcsel);
 273         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
 274                          adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
 275
 276         /* wait 3 AC97 time slots + delay for conversion */
 277         poll_delay(delay);
 278
 279         /* wait for POLL to go low */
 280         while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
 281                && timeout) {
 282                 udelay(AC97_LINK_FRAME);
 283                 timeout--;
 284         }
 285
 286         if (timeout <= 0) {
 287                 /* If PDEN is set, we can get a timeout when pen goes up */
 288                 if (is_pden(wm))
 289                         wm->pen_probably_down = 0;
 290                 else
 291                         dev_dbg(wm->dev, "adc sample timeout");
 292                 return RC_PENUP;
 293         }
 294
 295         *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
 296         if (wm->mach_ops && wm->mach_ops->post_sample)
 297                 wm->mach_ops->post_sample(adcsel);
 298
 299         /* check we have correct sample */
 300         if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
 301                 dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
 302                 *sample & WM97XX_ADCSEL_MASK);
 303                 return RC_PENUP;
 304         }
 305
 306         if (!(*sample & WM97XX_PEN_DOWN)) {
 307                 wm->pen_probably_down = 0;
 308                 return RC_PENUP;
 309         }
 310
 311         return RC_VALID;
 312 }
 313
 314 /*
 315  * Read a coord from the WM9712 adc in polling mode.
 316  */
 317 static int wm9712_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
 318 {
 319         int timeout = 5 * delay;
 320
 321         if (!wm->pen_probably_down) {
 322                 u16 data_rd = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
 323                 if (!(data_rd & WM97XX_PEN_DOWN))
 324                         return RC_PENUP;
 325                 wm->pen_probably_down = 1;
 326         }
 327
 328         /* set up digitiser */
 329         if (wm->mach_ops && wm->mach_ops->pre_sample)
 330                 wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
 331
 332         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
 333                 WM97XX_COO | WM97XX_POLL | WM97XX_DELAY(delay));
 334
 335         /* wait 3 AC97 time slots + delay for conversion and read x */
 336         poll_delay(delay);
 337         data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
 338         /* wait for POLL to go low */
 339         while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
 340                && timeout) {
 341                 udelay(AC97_LINK_FRAME);
 342                 timeout--;
 343         }
 344
 345         if (timeout <= 0) {
 346                 /* If PDEN is set, we can get a timeout when pen goes up */
 347                 if (is_pden(wm))
 348                         wm->pen_probably_down = 0;
 349                 else
 350                         dev_dbg(wm->dev, "adc sample timeout");
 351                 return RC_PENUP;
 352         }
 353
 354         /* read back y data */
 355         data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
 356         if (pil)
 357                 data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
 358         else
 359                 data->p = DEFAULT_PRESSURE;
 360
 361         if (wm->mach_ops && wm->mach_ops->post_sample)
 362                 wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
 363
 364         /* check we have correct sample */
 365         if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
 366                 goto err;
 367         if (pil && !(data->p & WM97XX_ADCSEL_PRES))
 368                 goto err;
 369
 370         if (!(data->x & WM97XX_PEN_DOWN) || !(data->y & WM97XX_PEN_DOWN)) {
 371                 wm->pen_probably_down = 0;
 372                 return RC_PENUP;
 373         }
 374         return RC_VALID;
 375 err:
 376         return 0;
 377 }
 378
 379 /*
 380  * Sample the WM9712 touchscreen in polling mode
 381  */
 382 static int wm9712_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
 383 {
 384         int rc;
 385
 386         if (coord) {
 387                 rc = wm9712_poll_coord(wm, data);
 388                 if (rc != RC_VALID)
 389                         return rc;
 390         } else {
 391                 rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
 392                 if (rc != RC_VALID)
 393                         return rc;
 394
 395                 rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
 396                 if (rc != RC_VALID)
 397                         return rc;
 398
 399                 if (pil && !five_wire) {
 400                         rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_PRES,
 401                                                 &data->p);
 402                         if (rc != RC_VALID)
 403                                 return rc;
 404                 } else
 405                         data->p = DEFAULT_PRESSURE;
 406         }
 407         return RC_VALID;
 408 }
 409
 410 /*
 411  * Enable WM9712 continuous mode, i.e. touch data is streamed across
 412  * an AC97 slot
 413  */
 414 static int wm9712_acc_enable(struct wm97xx *wm, int enable)
 415 {
 416         u16 dig1, dig2;
 417         int ret = 0;
 418
 419         dig1 = wm->dig[1];
 420         dig2 = wm->dig[2];
 421
 422         if (enable) {
 423                 /* continous mode */
 424                 if (wm->mach_ops->acc_startup) {
 425                         ret = wm->mach_ops->acc_startup(wm);
 426                         if (ret < 0)
 427                                 return ret;
 428                 }
 429                 dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
 430                         WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
 431                 dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
 432                         WM97XX_DELAY(delay) |
 433                         WM97XX_SLT(wm->acc_slot) |
 434                         WM97XX_RATE(wm->acc_rate);
 435                 if (pil)
 436                         dig1 |= WM97XX_ADCSEL_PRES;
 437                 dig2 |= WM9712_PDEN;
 438         } else {
 439                 dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
 440                 dig2 &= ~WM9712_PDEN;
 441                 if (wm->mach_ops->acc_shutdown)
 442                         wm->mach_ops->acc_shutdown(wm);
 443         }
 444
 445         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
 446         wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
 447
 448         return 0;
 449 }
 450
 451 struct wm97xx_codec_drv wm9712_codec = {
 452         .id = WM9712_ID2,
 453         .name = "wm9712",
 454         .poll_sample = wm9712_poll_sample,
 455         .poll_touch = wm9712_poll_touch,
 456         .acc_enable = wm9712_acc_enable,
 457         .phy_init = wm9712_phy_init,
 458         .dig_enable = wm9712_dig_enable,
 459         .dig_restore = wm9712_dig_restore,
 460         .aux_prepare = wm9712_aux_prepare,
 461 };
 462 EXPORT_SYMBOL_GPL(wm9712_codec);
 463
 464 /* Module information */
 465 MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
 466 MODULE_DESCRIPTION("WM9712 Touch Screen Driver");
 467 MODULE_LICENSE("GPL");