2 * SBC8349E Device Tree Source
4 * Copyright 2007 Wind River Inc.
6 * Paul Gortmaker (see MAINTAINERS for contact information)
8 * -based largely on the Freescale MPC834x_MDS dts.
10 * This program is free software; you can redistribute it and/or modify it
11 * under the terms of the GNU General Public License as published by the
12 * Free Software Foundation; either version 2 of the License, or (at your
13 * option) any later version.
20 compatible = "SBC834xE";
39 d-cache-line-size = <0x20>; // 32 bytes
40 i-cache-line-size = <0x20>; // 32 bytes
41 d-cache-size = <0x8000>; // L1, 32K
42 i-cache-size = <0x8000>; // L1, 32K
43 timebase-frequency = <0>; // from bootloader
44 bus-frequency = <0>; // from bootloader
45 clock-frequency = <0>; // from bootloader
50 device_type = "memory";
51 reg = <0x00000000 0x10000000>; // 256MB at 0
58 ranges = <0x0 0xe0000000 0x00100000>;
59 reg = <0xe0000000 0x00000200>;
63 compatible = "mpc83xx_wdt";
71 compatible = "fsl-i2c";
73 interrupts = <0xe 0x8>;
74 interrupt-parent = <&ipic>;
82 compatible = "fsl-i2c";
84 interrupts = <0xf 0x8>;
85 interrupt-parent = <&ipic>;
90 compatible = "fsl_spi";
91 reg = <0x7000 0x1000>;
92 interrupts = <0x10 0x8>;
93 interrupt-parent = <&ipic>;
97 /* phy type (ULPI or SERIAL) are only types supported for MPH */
100 compatible = "fsl-usb2-mph";
101 reg = <0x22000 0x1000>;
102 #address-cells = <1>;
104 interrupt-parent = <&ipic>;
105 interrupts = <0x27 0x8>;
109 /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
112 compatible = "fsl-usb2-dr";
113 reg = <0x23000 0x1000>;
114 #address-cells = <1>;
116 interrupt-parent = <&ipic>;
117 interrupts = <0x26 0x8>;
123 #address-cells = <1>;
125 compatible = "fsl,gianfar-mdio";
126 reg = <0x24520 0x20>;
128 phy0: ethernet-phy@19 {
129 interrupt-parent = <&ipic>;
130 interrupts = <0x14 0x8>;
132 device_type = "ethernet-phy";
134 phy1: ethernet-phy@1a {
135 interrupt-parent = <&ipic>;
136 interrupts = <0x15 0x8>;
138 device_type = "ethernet-phy";
142 enet0: ethernet@24000 {
144 device_type = "network";
146 compatible = "gianfar";
147 reg = <0x24000 0x1000>;
148 local-mac-address = [ 00 00 00 00 00 00 ];
149 interrupts = <0x20 0x8 0x21 0x8 0x22 0x8>;
150 interrupt-parent = <&ipic>;
151 phy-handle = <&phy0>;
152 linux,network-index = <0>;
155 enet1: ethernet@25000 {
157 device_type = "network";
159 compatible = "gianfar";
160 reg = <0x25000 0x1000>;
161 local-mac-address = [ 00 00 00 00 00 00 ];
162 interrupts = <0x23 0x8 0x24 0x8 0x25 0x8>;
163 interrupt-parent = <&ipic>;
164 phy-handle = <&phy1>;
165 linux,network-index = <1>;
168 serial0: serial@4500 {
170 device_type = "serial";
171 compatible = "ns16550";
172 reg = <0x4500 0x100>;
173 clock-frequency = <0>;
174 interrupts = <0x9 0x8>;
175 interrupt-parent = <&ipic>;
178 serial1: serial@4600 {
180 device_type = "serial";
181 compatible = "ns16550";
182 reg = <0x4600 0x100>;
183 clock-frequency = <0>;
184 interrupts = <0xa 0x8>;
185 interrupt-parent = <&ipic>;
188 /* May need to remove if on a part without crypto engine */
191 compatible = "talitos";
192 reg = <0x30000 0x10000>;
193 interrupts = <0xb 0x8>;
194 interrupt-parent = <&ipic>;
196 channel-fifo-len = <0x18>;
197 exec-units-mask = <0x0000007e>;
198 /* desc mask is for rev2.0,
199 * we need runtime fixup for >2.0 */
200 descriptor-types-mask = <0x01010ebf>;
204 * interrupts cell = <intr #, sense>
205 * sense values match linux IORESOURCE_IRQ_* defines:
206 * sense == 8: Level, low assertion
207 * sense == 2: Edge, high-to-low change
210 interrupt-controller;
211 #address-cells = <0>;
212 #interrupt-cells = <2>;
214 device_type = "ipic";
220 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
224 0x8800 0x0 0x0 0x1 &ipic 0x14 0x8
225 0x8800 0x0 0x0 0x2 &ipic 0x15 0x8
226 0x8800 0x0 0x0 0x3 &ipic 0x16 0x8
227 0x8800 0x0 0x0 0x4 &ipic 0x17 0x8>;
229 interrupt-parent = <&ipic>;
230 interrupts = <0x42 0x8>;
232 ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
233 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
234 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
235 clock-frequency = <66666666>;
236 #interrupt-cells = <1>;
238 #address-cells = <3>;
239 reg = <0xe0008500 0x100>;
240 compatible = "fsl,mpc8349-pci";