This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[SCSI] add support for variable length extended commands
Add support for variable-length, extended, and vendor specific
CDBs to scsi-ml. It is now possible for initiators and ULD's
to issue these types of commands. LLDs need not change much.
All they need is to raise the .max_cmd_len to the longest command
they support (see iscsi patch).
- clean-up some code paths that did not expect commands to be
larger than 16, and change cmd_len members' type to short as
char is not enough.
Linus Torvalds [Fri, 2 May 2008 15:20:43 +0000 (08:20 -0700)]
Merge branch 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: cleanup: drop .data.idt section in vmlinux.lds script
m32r: use KBUILD_DEFCONFIG
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: make Launcher see device status updates
lguest: remove bogus NULL cpu check
lguest: avoid using NR_CPUS as a bounds check.
virtio: add virtio disk geometry feature
virtio: explicit advertisement of driver features
virtio: change config to guest endian.
virtio: finer-grained features for virtio_net
virtio: wean net driver off NETDEV_TX_BUSY
virtio-blk: fix remove oops
virtio: fix scatterlist sizing in net driver.
virtio: de-structify virtio_block status byte
virtio: export more headers to userspace
virtio: fix sparse return void-valued expression warnings
virtio: fix tx_ stats in virtio_net
virtio: ignore corrupted virtqueues rather than spinning.
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
David S. Miller [Fri, 2 May 2008 05:28:17 +0000 (22:28 -0700)]
sparc32: More memory probing consolidation.
The PROM library function prom_meminit() builds a table,
prom_phys_avail[], just so that probe_memory() in
arch/sparc/mm/fault.c can copy it into sp_banks[].
Just have prom_meminit() fill in the sp_banks[] array directly, and
remove duplicated sort() function.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 2 May 2008 04:28:59 +0000 (21:28 -0700)]
sparc32: Kill totally unused memory information tables.
The code in arch/sparc/prom/memory.c computes three tables, the list
of total memory, the list of available memory (total minus what
firmware is using), and the list of firmware taken memory.
Only the available memory list is even used.
Therefore, kill those unused tables and make prom_meminfo() return
just the available memory list.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 1 May 2008 10:30:22 +0000 (03:30 -0700)]
sparc64: Fix syscall restart, for real...
The change I put into copy_thread() just papered over the real
problem.
When we are looking to see if we should do a syscall restart, when
deliverying a signal, we should only interpret the syscall return
value as an error if the carry condition code(s) are set.
Otherwise it's a success return.
Also, sigreturn paths should do a pt_regs_clear_trap_type().
It turns out that doing a syscall restart when returning from a fork()
does and should happen, from time to time. Even if copy_thread()
returns success, copy_process() can still unwind and signal
-ERESTARTNOINTR in the parent.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty Russell [Sat, 3 May 2008 02:50:51 +0000 (21:50 -0500)]
lguest: avoid using NR_CPUS as a bounds check.
NR_CPUS (being a host number) is an arbitrary limit for the Guest.
Using the array size directly (which currently happes to be NR_CPUS)
is more futureproof.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Ryan Harper [Wed, 16 Apr 2008 18:56:37 +0000 (13:56 -0500)]
virtio: add virtio disk geometry feature
Rather than faking up some geometry, allow the backend to push the disk
geometry via virtio pci config option. Keep the old geo code around for
compatibility.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com> Reviewed-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (modified to single struct)
Rusty Russell [Sat, 3 May 2008 02:50:50 +0000 (21:50 -0500)]
virtio: explicit advertisement of driver features
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Sat, 3 May 2008 02:50:49 +0000 (21:50 -0500)]
virtio: change config to guest endian.
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API, in particular how easy it is to break big
endian machines.
The virtio config space was originally chosen to be little-endian,
because we thought the config might be part of the PCI config space
for virtio_pci. It's actually a separate mmio region, so that
argument holds little water; as only x86 is currently using the virtio
mechanism, we can change this (but must do so now, before the
impending s390 merge).
API changes:
- __virtio_config_val() just becomes a striaght vdev->config_get() call.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Sat, 3 May 2008 02:50:46 +0000 (21:50 -0500)]
virtio: finer-grained features for virtio_net
So, we previously had a 'VIRTIO_NET_F_GSO' bit which meant that 'the
host can handle csum offload, and any TSO (v4&v6 incl ECN) or UFO
packets you might want to send. I thought this was good enough for
Linux, but it actually isn't, since we don't do UFO in software.
So, add separate feature bits for what the host can handle. Add
equivalent ones for the guest to say what it can handle, because LRO
is coming too (thanks Herbert!).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Sat, 3 May 2008 02:50:45 +0000 (21:50 -0500)]
virtio: fix scatterlist sizing in net driver.
Herbert Xu points out (within another patch) that my scatterlists are
too short: one entry for the gso header, one for the skb->data, and
MAX_SKB_FRAGS for all the fragments.
Fix both xmit and recv sides (recv currently unused, coming in later
patch).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
is there a reason why we dont export the virtio headers for
9p, balloon, console, pci, and virtio_ring? kvm uses make sync,
but I think it is still useful to heave these headers exported
as they might be useful for other userspace tools.
I dont export virtio.h, because it does not seem to have useful
information for userspace and it requires scatterlist.h which is
also not exported. See also my other mail about your "virtio:
change config to guest endian." patch.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Sat, 3 May 2008 02:50:43 +0000 (21:50 -0500)]
virtio: ignore corrupted virtqueues rather than spinning.
A corrupt virtqueue (caused by the other end screwing up) can have
strange results such as a driver spinning: just bail when we try to
get a buffer from a known-broken queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Thomas Gleixner [Mon, 28 Apr 2008 15:01:56 +0000 (17:01 +0200)]
genirq: reenable a nobody cared disabled irq when a new driver arrives
Uwe Kleine-Koenig has some strange hardware where one of the shared
interrupts can be asserted during boot before the appropriate driver
loads. Requesting the shared irq line from another driver result in a
spurious interrupt storm which finally disables the interrupt line.
I have seen similar behaviour on resume before (the hardware does not
work anymore so I can not verify).
Change the spurious disable logic to increment the disable depth and
mark the interrupt with an extra flag which allows us to reenable the
interrupt when a new driver arrives which requests the same irq
line. In the worst case this will disable the irq again via the
spurious trap, but there is a decent chance that the new driver is the
one which can handle the already asserted interrupt and makes the box
usable again.
Eric Biederman said further: This case also happens on a regular basis
in kdump kernels where we deliberately don't shutdown the hardware
before starting the new kernel. This patch should reduce the need for
using irqpoll in that situation by a small amount.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-and-Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Denis V. Lunev [Fri, 2 May 2008 11:12:41 +0000 (04:12 -0700)]
netns: assign PDE->data before gluing entry into /proc tree
In this unfortunate case, proc_mkdir_mode wrapper can't be used anymore and
this is no way to reuse proc_create_data due to nlinks assignment. So,
copy the code from proc_mkdir and assign PDE->data at the appropriate
moment.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 2 May 2008 09:46:22 +0000 (02:46 -0700)]
net: assign PDE->data before gluing PDE into /proc tree
Simply replace proc_create and further data assigned with proc_create_data.
Additionally, there is no need to assign NULL to PDE->data after creation,
/proc generic has already done this for us.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mackerras [Fri, 2 May 2008 04:29:12 +0000 (14:29 +1000)]
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
This fixes a regression reported by Kamalesh Bulabel where a POWER4
machine would crash because of an SLB miss at a point where the SLB
miss exception was unrecoverable. This regression is tracked at:
http://bugzilla.kernel.org/show_bug.cgi?id=10082
SLB misses at such points shouldn't happen because the kernel stack is
the only memory accessed other than things in the first segment of the
linear mapping (which is mapped at all times by entry 0 of the SLB).
The context switch code ensures that SLB entry 2 covers the kernel
stack, if it is not already covered by entry 0. None of entries 0
to 2 are ever replaced by the SLB miss handler.
Where this went wrong is that the context switch code assumes it
doesn't have to write to SLB entry 2 if the new kernel stack is in the
same segment as the old kernel stack, since entry 2 should already be
correct. However, when we start up a secondary cpu, it calls
slb_initialize, which doesn't set up entry 2. This is correct for
the boot cpu, where we will be using a stack in the kernel BSS at this
point (i.e. init_thread_union), but not necessarily for secondary
cpus, whose initial stack can be allocated anywhere. This doesn't
cause any immediate problem since the SLB miss handler will just
create an SLB entry somewhere else to cover the initial stack.
In fact it's possible for the cpu to go quite a long time without SLB
entry 2 being valid. Eventually, though, the entry created by the SLB
miss handler will get overwritten by some other entry, and if the next
access to the stack is at an unrecoverable point, we get the crash.
This fixes the problem by making slb_initialize create a suitable
entry for the kernel stack, if we are on a secondary cpu and the stack
isn't covered by SLB entry 0. This requires initializing the
get_paca()->kstack field earlier, so I do that in smp_create_idle
where the current field is initialized. This also abstracts a bit of
the computation that mk_esid_data in slb.c does so that it can be used
in slb_initialize.
Other OS wakeup is not supported from the IR controller,
the bluetooth controller nor the RTC. Remove references
to these in the PS3 sys-manager source.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arrange for a syntax check to always be done on the powerpc/mm/slb.c
DBG() macro by defining it to pr_debug() for non-debug builds.
Also, fix these related compile warnings:
slb.c:273: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'long unsigned int
slb.c:274: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala [Wed, 30 Apr 2008 15:24:44 +0000 (10:24 -0500)]
[POWERPC] Xilinx: Fix compile warnings
arch/powerpc/sysdev/xilinx_intc.c: In function 'xilinx_intc_init':
arch/powerpc/sysdev/xilinx_intc.c:111: warning: format '%08X' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/char/xilinx_hwicap/xilinx_hwicap.c: In function 'hwicap_setup':
drivers/char/xilinx_hwicap/xilinx_hwicap.c:626: warning: cast to pointer from integer of different size
drivers/char/xilinx_hwicap/xilinx_hwicap.c:646: warning: format '%x' expects type 'unsigned int', but argument 6 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Randy Dunlap [Wed, 30 Apr 2008 23:45:58 +0000 (16:45 -0700)]
[RAPIDIO] fix current kernel-doc notation
Fix current (-git16) missing docbook/kernel-doc notation in RapidIO files.
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'sys_size'
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'phy_type'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:188): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:224): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:245): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:270): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:311): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:996): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ivo van Doorn [Mon, 21 Apr 2008 17:01:09 +0000 (19:01 +0200)]
rt2x00: Fix quality/activity led handling
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Moss [Thu, 17 Apr 2008 23:03:40 +0000 (16:03 -0700)]
iwlwifi: fix debug messages during scanning
direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.
Now make all debugging consistent.
Signed-off-by: Bill Moss <bmoss@clemson.edu> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Guy Cohen [Mon, 21 Apr 2008 22:41:57 +0000 (15:41 -0700)]
iwlwifi: fix current channel is not scanned
All channels should be scanned, including the current channel
when the client is associated.
Removed also unused flag to scan only active channels.
Signed-off-by: Guy Cohen <guy.cohen@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Al Viro [Thu, 1 May 2008 21:36:36 +0000 (14:36 -0700)]
[IA64] fix file and descriptor handling in perfmon
Races galore... General rule: as soon as it's in descriptor table,
it's over; another thread might have started IO on it/dup2() it
elsewhere/dup2() something *over* it/etc. fd_install() is the very
last step one should take - it's a point of no return.
Besides, the damn thing leaked on failure exits...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Tony Luck <tony.luck@intel.com>
Roland McGrath [Wed, 30 Apr 2008 21:40:14 +0000 (14:40 -0700)]
[IA64] TS_RESTORE_SIGMASK
Replace TIF_RESTORE_SIGMASK with TS_RESTORE_SIGMASK and define
our own set_restore_sigmask() function. This saves the costly
SMP-safe set_bit operation, which we do not need for the sigmask
flag since TIF_SIGPENDING always has to be set too.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
slabinfo: Support printout of the number of fallbacks
Add functionality to slabinfo to print out the number of fallbacks
that have occurred for each slab cache when the -D option is specified.
Also widen the allocation / free field since the numbers became
too big after a week.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Linus Torvalds [Thu, 1 May 2008 18:31:38 +0000 (11:31 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-sbp2: log scsi_target ID at release
ieee1394: fix NULL pointer dereference in sysfs access
can potentially trigger a deadlock. To avoid this deadlock a fix
similar to that found in the 8250.c serial driver is applied. The
deadlock is avoided by releasing the lock before pushing a buffer
and reacquiring it when completed.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jared Hulbert [Wed, 30 Apr 2008 06:26:49 +0000 (23:26 -0700)]
[MTD][NOR] Add physical address to point() method
Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com> Reviewed-by: Jörn Engel <joern@logfs.org> Acked-by: Nicolas Pitre <nico@cam.org> Acked-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Stefan Richter [Thu, 1 May 2008 08:43:04 +0000 (10:43 +0200)]
ieee1394: fix NULL pointer dereference in sysfs access
Regression since "ieee1394: prevent device binding of raw1394,
video1394, dv1394", commit d2ace29fa44589da51fedc06a67b3f05301f3bfd:
$ cat /sys/bus/ieee1394/drivers/raw1394/device_ids
triggers a NULL pointer dereference in fw_show_drv_device_ids.
Reported by Miles Lane.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Miles Lane <miles.lane@gmail.com>
David Woodhouse [Thu, 1 May 2008 17:47:17 +0000 (18:47 +0100)]
[JFFS2] Track parent inode for directories (for NFS export)
To support NFS export, we need to know the parent inode of directories.
Rather than growing the jffs2_inode_cache structure, share space with
the nlink field -- which was always set to 1 for directories anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With s390 the last arch switched to the generic sys_ptrace yesterday so
we can now kill the ifdef around it to enforce every new port it using
it instead of introducing new weirdo versions.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 28 Apr 2008 00:04:15 +0000 (20:04 -0400)]
[PATCH] fix sysctl_nr_open bugs
* if luser with root sets it to something that is not a multiple of
BITS_PER_LONG, the system is screwed.
* if it gets decreased at the wrong time, we can get expand_files()
returning success and _not_ increasing the size of table as asked.
Al Viro [Sat, 23 Feb 2008 11:46:49 +0000 (06:46 -0500)]
[PATCH] sanitize anon_inode_getfd()
a) none of the callers even looks at inode or file returned by anon_inode_getfd()
b) any caller that would try to look at those would be racy, since by the time
it returns we might have raced with close() from another thread and that
file would be pining for fjords.
Al Viro [Wed, 23 Apr 2008 04:49:25 +0000 (00:49 -0400)]
[PATCH] remove horrors with irix tty ioctls handling
Existing code in there (get_tty(), etc.) is both severely
racy *and* pointless: ioctls in question have Linux equivalents
and there's no need to play silly buggers in irix_ioctl() -
just need to replace arguments and, in case of TIOCGSID,
deal with API differences - Linux one expects pid_t __user *
while Irix one does unsigned long __user *. BFD...
Al Viro [Tue, 22 Apr 2008 23:46:10 +0000 (19:46 -0400)]
[PATCH] fix file and descriptor handling in perfmon
Races galore... General rule: as soon as it's in descriptor table,
it's over; another thread might have started IO on it/dup2() it
elsewhere/dup2() something *over* it/etc. fd_install() is the very
last step one should take - it's a point of no return.
Besides, the damn thing leaked on failure exits...
Grant Likely [Thu, 1 May 2008 17:05:58 +0000 (11:05 -0600)]
[POWERPC] mpc5200: Allow for fixed speed MII configurations
Various improvements for configuring the MPC5200 MII link from the
device tree:
* Look for 'current-speed' property for fixed speed MII links
* Look for 'fsl,7-wire-mode' property for boards using the 7 wire mode
* move definition of private data structure out of the header file
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Linus Torvalds [Thu, 1 May 2008 15:28:26 +0000 (08:28 -0700)]
Merge branch 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (adt7473) minor cleanup / refactoring
hwmon: (asb100) Remove some dead code
hwmon: (lm75) Fix an incorrect comment
hwmon: (w83793) VID and VRM handling cleanups
hwmon: (w83l785ts) Don't ask the user to report failures
hwmon: (smsc47b397) add a new chip id (0x8c)
linux-2.6-mk68/drivers/net/fec.c: In function 'fec_enet_module_init':
linux-2.6-mk68/drivers/net/fec.c:2627: warning: unused variable 'j'
linux-2.6-mk68/drivers/net/fec.c: At top level:
linux-2.6-mk68/drivers/net/fec.c:2136: warning: 'mii_link_interrupt' defined but not used
Renamed the 5272 hash_table registers to match the "grp" hash_table
registers of the other ColdFire parts. They are actually a group hash.
The makes for consistent setup across all ColdFire parts.